Modular Jack Connectors for High-Speed LAN Transmission

Size: px

Start display at page:

Download "Modular Jack Connectors for High-Speed LAN Transmission"

Liliana Griffith
5 years ago
Views:

NEW Modular Jack Connectors for High-Speed LAN Transmission TM2R Series Built-in Optical Indicators Optical indicator LED Optical pipe Features.

Single port configuration meeting CAT5e and multiple port configuration meeting CAT5 transmission performance.

Built-in Optical Indicators Optical indicators are integral part of the connectors saving space on customer s board. Compared with LED type indicators, they do not emit any electrical noise.

1 NEW Modular Jack Connectors for High-Speed LAN Transmission TM2R Series Built-in Optical Indicators Optical indicator LED Optical pipe Features. Supports High-Speed LAN Transmission Meets requirements of TIA/EIA-568-B data wiring standard. Single port configuration meeting CAT5e and multiple port configuration meeting CAT5 transmission performance. As such, these products fully support Gigabit Ethernet (BASE-T) and Fast Ethernet (BASE-TX) highspeed LAN transmission. 2. Built-in Optical Indicators Optical indicators are integral part of the connectors saving space on customer s board. Compared with LED type indicators, they do not emit any electrical noise.. EMI protection Metal shield covers the outer surfaces of the connectors assuring complete protection against electromagnetic interference. Built-in multiple shield and ground contacts assure reliable connection with the mounting panel as well as with the mating connector. 4. FCC Standards Meets requirements of FCC Title 47, Part 68, Subpart F. Housing Space saving Optical indicator area Optical indicator One additional TM2 multi-port jack can be mounted in the space previously occupied by LEDs. Applications Telecom Hubs, Routers, Bridges and ATM Transmission Equipment, Ethernet Switches and Networking Equipment, Test and Measurement Equipment, Medical Diagnostic Equipment. Built-in LED type (Possibility of electromagnetic noise emission and interference.) Built-in Optical pipe type (No electromagnetic noise emission.) 22.

2 Product Specifications Ratings Current rating Voltage rating A 25 V AC Operating temperature range-25ç to +8ç (Note) Item Specification Conditions.Insulation resistance 2.Dielectric Withstanding Voltage (between adjacent contacts) M ohms min No flashover or insulation breakdown V DC 5 V AC / one minute.withstanding voltage (between contact and shield) 4.Contact resistance 5.Vibration 6.Shock 7.Durability (mating/unmating) 8.Temperature cycle 9.Humidity.Salt Spray No flashover or insulation breakdown 2 m ohms max. No electrical discontinuity of 5 ms or more Contact resistance: 25m ohms max. No electrical discontinuity of 5ms or more Contact resistance: 25m ohms max. Contact resistance: 25m ohms max. Contact resistance: 25 m ohms max. Insulation resistance: M ohms min. Contact resistance: 25 m ohms max. Insulation resistance: M ohms min. (High humidity) Insulation resistance: M ohms min. (Dry state) Contact resistance: 25 m ohms max. 5 V AC / one minute ma DC Frequency: to 55 Hz, single amplitude of.75 mm, 2 hours / axis Acceleration of 49 m/s 2, ms duration, sine half-wave waveform, cycles in each of the axis 2 cycles (Temperature: -55ç/+5ç to +5ç/+85ç/+5ç to +5ç Duration: / 5 / / 5 (Minutes) 5 cycles 5 hours at temperature of 4ç and humidity of 9% to 95% Exposed to density 5% salt water for 48 hours Note :Includes temperature rise caused by current flow. Materials Part Material Finish Remarks Insulator Contact Optical pipe Shield PBT Copper alloy Poly carbonate Copper alloy Color: Black Contact area: Gold plating Termination area: Solder plating Color: Clear Tin plating UL94V Ordering information Jacks TM2 R - 5 A D - LP q Series Name TM2 w Connector type R : Jack e Jack type number 5 : PCB Right-angle through hole type r Jack performance level code A : CAT5 (Single row, multi-port) B : CAT5 (Double row, multi port) C : Supports CAT5e (Single port) t Jack opening code 8 : 8 contacts 2 : 8 contacts /4 ports 48 : 8 contact/6 ports y Number of inserted contacts 8 : 8 contact 2 : 8 contact inserted in 4 ports=2 contacts 48 : 8 contact inserted in 6 ports=48 contacts u Number of rows Blank: Single row D: Double row i Optical pipe LP: With optical pipe inserted Blank: Without optical pipe 2

Modular Jack Connectors Supporting CAT5e Single Port With Built-in Optical Pipe 6 Contact No. 2.25.6 (2.8).4 5.75.75.4.7.45.5.5 6.5 2.54.25.5 24 Contact No.7 TM2R-5C PC.9 Contact No. Contact No.2 TM2R-5C-88-LP 222-2892- Single Port Without Optical Pipe 2 6 Contact No.

3 Modular Jack Connectors Supporting CAT5e Single Port With Built-in Optical Pipe 6 Contact No (2.8) Contact No.7 TM2R-5C PC.9 Contact No. Contact No.2 TM2R-5C-88-LP Single Port Without Optical Pipe 2 6 Contact No..25 (2.8) Contact No.7 TM2R-5C PC Contact No..9 Contact No.2 TM2R-5C

4 BRecommended PCB mounting patterns With Built-in Optical Pipe Without Optical Pipe Ø.6 8-Ø LED location area.27 LED light emission area No ground traces Contact No Ø MIN 6.75 MIN Printed board edge.4 Connector front edge.4min 5.75 No conductive traces Ø.2 2-Ø.6 8-Ø Contact No. No ground traces 6.75 MIN MIN 6.75 Printed board edge Connector front edge.4min No conductive traces 2 *Recommendations for PCB Design The contact arrangement differs between the contact area side and Printed board side. (,2,,4,5,6,7,8 on the contact are side / 2,,,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. Area indicated should be free of ground traces. 4 Recommended board thickness:.6mm. 5 To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. 5 PCB mounting pattern Other Series TM2R Series Suggested LEDs LED light emitting center 2.7MAX.2MAX.5MAX BPanel Cutout For Both Types, With and Without Built-in Optical Pipe PCB mounting surface 4.5MIN 4..6MIN TM2P--88P () Lock lever TM2R--5C--88--LP.5 Panel side 6.4 Connector front surface *Recommendations for Panel Design The shield contacts should connect with the panel cut-out on all sides. 4

Modular Receptacles Supporting CAT5 Single row/ multiple ports, with Built-in Optical Pipe 59.8 4.9 25.9 TM2R-5A-22-LP 222-287-5.97 Contact No..75 5..7 5.4.45 (.5) Contact No.2.25.5 Contact No.

5 Modular Receptacles Supporting CAT5 Single row/ multiple ports, with Built-in Optical Pipe TM2R-5A-22-LP Contact No (.5) Contact No Contact No. Contact No BRecommended PCB mounting patterns LED Mount Area Dimensions 6MAX Ø2 MIN 4-Ø2 2-Ø LED location area 4 LED light emission area.97 Contact No. No conductive traces Ø Printed board edge Connector front edge CL-22 Series.9 SML-2 Series SML- Series *Recommendations for PCB Design The contact arrangement differs between the contact area side and Printed board side. (,2,,4,5,6,7,8 on the contact are side / 2,,,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. Recommended board thickness:.6mm. 4 To assure that the indicator light pipes operates correctly the LED s must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. 4 Suggested LEDs Series Name Manufacturer CL-22 SML- SML-2 Citizen Electronics Co., Ltd. Rohm Co., LTD Rohm Co., LTD PCB mounting pattern

6 BRecommended Panel Cutout PCB mounting surface MIN.4MIN Shield spring contact Panels Side 59.6 (4) TM2P-- 88P Connector front surface Lock lever 6 MAX *Recommendations for Panel Design The shield contacts should connect with the panel cut-out on all sides. 6

Double row / multiple port, with Built-in Optical Pipe TM2R-5B-22D-LP A B.97.45 Contact No..25 C D Lower row connectors contacts Upper row Contact No. 28.6 Lower row 5.8 8.4 27.9.75 (.5).4 2.5 4.94.

85 8.75 86.87 BRecommended PCB mounting pattern 4 4 Upper row LED mount position Lower row LED mount position.4..2.9 7.7 A B LED light emission area E- Ø2.97 8.89 6.5.8.27 Upper row contact hole Lower row contact hole 6 MAX 9.

7 Double row / multiple port, with Built-in Optical Pipe TM2R-5B-22D-LP A B Contact No..25 C D Lower row connectors contacts Upper row Contact No Lower row (.5) PBT TM2R-5B-4848D-LP.9 Upper row connectors contacts 7.7 TM2R-5B-22D-LP TM2R-5B-4848D-LP A B C D BRecommended PCB mounting pattern 4 4 Upper row LED mount position Lower row LED mount position A B LED light emission area E- Ø Upper row contact hole Lower row contact hole 6 MAX MIN D- Ø 4- Ø2 2- Ø.2 Contact No No conductive traces 2 C Printed board edge Connector front edge TM2R-5B-22D-LP TM2R-5B-4848D-LP A B C D E *Recommendations for PCB Design The contact arrangement differs between the contact area side and Printed board side. (,2,,4,5,6,7,8 on the contact are side / 2,,,4,5,6,8,7 on the printed board side) 2 Areas indicated should be free of conductive traces. Recommended board thickness:.6mm. 4 To assure that the indicator light pipes operates correctly the LED's must be installed directly on the PCB, within recommended dimensions and with light emitting center in upward direction. Contact applicable manufacturer for LED specification. PCB mounting pattern Other Series TM2R Series Suggested LEDs Series Name Manufacturer CL-22 Citizen Electronics Co., Ltd. 7

8 BPanes Cutout Shield spring contact spring 28.4 PCB mounting surface.5 4.5MIN.4 MIN.97 Panel Side A B A B TM2R-5B-22D-LP TM2R-5B-4848D-LP (4) TM2P -- 88P Lock lever TM2R -- 5B -- * * * * D -- LP Connector front surface 6 MAX *Recommendations for Panel Design The shield contacts should connect with the panel cut-out on all sides. 8

9 BTechnical Documentation CAT5e Transmission Characteristics Data Representative values of the various transmission characteristics data for fully mated receptacle (TM2R-5C-88-LP) and plug (TM2P-88P). All plugs in the TM2R-5C Series that were manufactured based on the De-embedded method of the TIA/EIA-568-B.2 standard and meet performance requirements of CAT5e single transmission. Note:These data are for the listed connector combination. Inquire with your Hirose Electric account representative about other combinations. Signal Attenuation.5 Attenuation(dB) ,2,6 4,5 7,8 CAT5e Spec Near-End Crosstalk (NEXT) Data 2 NEXT(dB) ,2-,6,2-4,5,2-7,8,6-4,5,6-7,8 4,5-7,8 CAT5e Spec Return Loss 8 Return Loss(dB) ,2,6 4,5 7,8 CAT5e Spec 9

10 Far-End Crosstalk (FEXT) 2 FEXT(dB) ,2-,6,2-4,5,2-7,8,6-,2,6-4,5,6-7,8 4,5-,2 4,5-,6 4,5-7,8 7,8-,2 7,8-,6 7,8-4,5 CAT5e Spec Propagation Delay 2.5 Delay(ns) ,2,6 4,5 7,8 CAT5e Spec Propagation Delay (Delay Skew) Delay Skew(ns) Measurement Value CAT5e Spec

11 BReference Documentation CAT6 Certification Received Only the high quality plugs in the TM2R-5C Series (based on the De-embedded method of the TIA/EIA-568-B.2 standard) clear CAT6 single transmission performance. A certificate was issued by the GHMT, independent European testing company. Certificate of Acceptance Return Loss NEXT

Modular Jack Connectors for High-Speed LAN Transmission

Modular Jack Connectors for High-Speed LAN Transmission TM2R Series Built-in Optical Indicators Optical indicator LED Optical pipe Features. Supports High-Speed LAN Transmission Meets requirements of TIA/EIA-568-B