Compact Flash Card Connectors

Transcription

1 Compact Flash Card Connectors Complies with Compact Flash Association MI2/2 Series (a)space-saving design Features. Compact design occupies minimum space Connectors are designed with small width and depth for miniaturization and the foot print on the board has been made smaller. (See (a) to the right) (b)suitable for automatic mounting Automatic equipment pick up area. 2. Supplied with ground terminals The MI2 Series are furnished with ground terminals. 3. Card ejection mechanism Two point ejection mechanism to assure even card ejection. 4. Designed and packaged for board placement with automatic equipment Headers are designed with a pick up area to accommodate the pick-and -place nozzles of automatic mounting machines. (Patents pending) Receptacles are designed to be mounted on top the board, and automatic mounting is possibble on the specified board. HRS Product Feature Fixed fittings make slider immobile. Construction facilitates pick-and-place process. Fixed 5. Card ejection mechanism Available in several termination and mouting styles, with and without ejection mechanism, with and without standoffs. 6. Rich variations A rich assortment of variations allows selection of a type to suit the specific card and the equipment to which it will be installed. ()Suitable cards: Type I, type I/II. (2)Eject button: None, right, left (3)Standoff: mm, 2.2 mm (4)Board mounting type: Standard, reverse Producut variation Series Mounting offset Ejector Cards Built-in nuts None None Typeor MI2 Standard Right 2.2 mm Left Type YES Reverse 2.2 mm None Type Ø(None) None Right MI2 Standard Left 2.2 mm None Typeor2 YES Reverse None None Note : Hexagonal nuts (M2.4) are required. Applications PDA, digital still cameras, etc. C2

2 Product Specifications Rating Current rating Voltage rating.5 A 25 V AC Operating temperature range Operating humidity range -55 to +85ç (Note ) Relative humidity 95% or less (No condensation) Storage temperature range Storage humidity range - to +6ç -4 to 7% Item Specification Conditions. Insulation resistance 2. Withstanding voltage 3. Contact resistance, M ohms min. No flashover or insulation breakdown. 4 m ohms max. (initial value) (Note 3) 5 V DC 5 V AC / minute ma 4. Vibration 5. Humidity (Steady state) 6. Temperature cycle 7. Durability (Insertion/withdrawal) No electrical discontinuity of ns or more Insulation resistance of M ohms min. Insulation resistance of M ohms min. Change of contact resistance from initial value is 2 m ohms max. Frequency: to 2 Hz, full amplitude of.52 mm or acceleration of 47 m/s 2 (peak), 4 hours in each of the 3 directions. 96 hours at temperature of 4ç and humidity of 9% to 95% Temperature: -55ç for 3 min. --> +5 to 35ç within 5 min. 85ç for 3 min. --> +5 to 35ç within 5 min. for 5 cycles cycles at 4 to 6 cycles per hour 8. Resistance to Soldering heat No deformation of components affecting performance. Reflow: At the recommended temperature profile Manual soldering: 3ç for 3 seconds Note : Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation. Note 3: This does not include the resistance of the conductor. Materials Item Part Material Finish Remarks Receptacle Header Insulator PPS Color:Black UL94V- Contacts Insulator Contacts Metal fitting Eject fitting Ground clip Nut Ordering Information Receptacles MI 2-5 RD - SF Headers Series name: MI Series No.: 2 Number of contacts: 5 Connector type RD: Receptacle Contact form SF: SMT Phosphor bronze PPS Brass Brass Stainless steel Stainless steel Steel MI 2 A - 5 PD R - SF - EJR (3) Contact Area : Gold plating Lead Area : Solder plating Color:Black Contact Area : Gold plating Termination Area : Solder plating Solder plating Series name: MI Series No. 2: for type I cards ( ) 2: for type I and II cards Stand off type Blank : None A : 2.2 mm Number of contacts: 5 Connector type PD: Header UL94V Applied to eject mechanism Applied to MI2 series Board mounting type Blank : Standard R : Reverse Contact type SF: SMT Eject button position EJR : Right button EJL : Left button Blank : None Built-in nut type (3): With built-in nuts Blank: Standard product ( ) Can accommodate type II cards only when standard mounting is used and stand off is mm. C3

3 Receptacle.27 No No No.5 No.26.2 (offset) 2.7 No.5 No (t.8 w.3) No. No.26 A Note The coplanarity of the conductor is. mm Max. MI2-5RD-SF (35) ±.5 (4.2) 2min 2-Rmax 5-.4±.3.635± max (Recommended board thickness=.4) C4

4 Headers for Type I or II Cards Eject button : None Offset : None.95 No No.38 No.26 No.25 No.3 No () 5±. 45.5± ±. 37±.5 2-Ø ± ±. 4±.5 4.5max (2) MI2--5PD No No No.2 No Polartiy mark No. 3.8 (.8) t :.25 w : Note : Coplanarity of all surface mount terminals and components is.. Note 2: Dimensions in parentheses ( ) are reference dimensions. MI2-5PD-SF Ø min +.634±.3 3.5± ±.5 No. 5-.4±.3 C5

5 Headers for Type I Cards Eject button : None Offset : 2.2 mm Mounting style : Reverse mounting 4.5 No. No.3 No.25 No.26 No No (27.9) (7.2) () () (4.5) No. No No.25 No No.5 (4.3) (4.3) t :.25 w :.25 (.5) Note : Coplanarity of all surface mount terminals and components is.. Note 2: Dimensions in parentheses ( ) are reference dimensions. 44 MI2A-5PDR-SF ±.5 2-Ø min 28.5±.5 4.5max 22.25±. 3.5±.5 No. 43.9±. 5.3±. 4.3±.5 37±.5.635±.3 3.5± ±.5 4±. 2-Ø ± Ø C6

6 Headers for Type I Cards Eject button : Right button Offset : 2.2 mm Note : The amount of card and button protrusion from the connector after mating is 3.6 mm. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be. maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. MI2A-5PD-SF-EJR C7

7 Headers for Type I Cards Eject button : Left side Offset : 2.2 mm Note : The amount of card and button protrusion from the connector after mating is 3.6 mm. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be. maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. MI2A-5PD-SF-EJL C8

8 Headers for Type I or II Cards Eject button : Right side Offset : mm Note : This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be. maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. MI2-5PD-SF-EJR C9

9 Headers for Type I or II Cards Eject button : Left side Offset : None Note : This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be. maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. MI2-5PD-SF-EJL C

10 Headers for Type I or II Cards Eject button : None Offset : None Note : This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be. maximum Note 4: Dimensions in parentheses ( ) are to be regarded as reference dimensions. MI2-5PD-SF C

11 Headers for Type I or II Cards Eject button : None Offset : None Mounting style : Reverse mounting Note : Coplanarity of all surface mount terminals and components is.. Note 2: Dimensions in parentheses ( ) are reference dimensions. MI2A-5PDR-SF C2

12 Headers for Type I and II Cards Eject button : Right side Offset : 2.2 mm Note : This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be. maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. MI2A-5PD-SF-EJR C3

13 Headers for Type I and II Cards Eject button : Left button Offset : 2.2 mm Note : This item is a (standard type) header for use with CompactFlash cards. Note 2: The dimensions of mating portion of this product comply with CFA standards. Note 3: This product can be automatically mounted. The suction surface for automatic mounting is positioned as illustrated in the figure. 3 This part is fixed in the initial condition, but released with a single operation of the ejector. (Amount of actual card ejection: 3.5 mm) Note 4: The coplanarity (degree of flatness) of the SMT lead tip portion and the reinforced fitting mounting end face is to be. maximum. Note 5: Dimensions in parentheses ( ) are to be regarded as reference dimensions. MI2A-5PD-SF-EJL C4

14 Headers for Type I and II Cards Eject button : None Offset : 2.2 mm Note : Coplanarity of all surface mount terminals and components is.. Note 2: Dimensions in parentheses ( ) are reference dimensions. MI2A-5PD-SF C5

15 BTemperature Profile Applicable Conditions Reflow system : IR reflow Solde : Paste type 63 Sn/37 Pb (Flux content 9 wt%) Test board Glass epoxy 6mm x 6mm x.6 mm Metal mask thickness:.5 mm Recommended temperature profile. The temperature may be slightly changed according to the solder paste type and amount. C6

16 BPrecautions for Use. Differentiate the side of the card at the time of CF card insertion. This product is furnished with an wrong insertion prevention mechanism which is compliant with CFA standards, but forced wrong insertion of the card may cause damage to the card. 2. Do not move the CF card up and down when it has been partially inserted. It may cause damage to the connector and card. Up CF Card Down 3. The package used for this product is the soft tray. We recommend a check before mounting, since the adjustment may be reqaired depending on the type of mounter. For more detailed information, please contact nearest Hirose account representative. 4. Recommended screw torque values. Screw type Standard torque Steel screws.42 Brass screws.24 Screws : M2 X.4 BWashing Conditions This product is a no-wash item, but in the case of washing, please observe the following conditions.. Organic Solvent Washing [Unit: N'm] Upper tolerance limit.8.68 Solvent IPA (Isopropyl alcohol) HCFC (Hydrochlorofluorocarbon) Room temperature washing YES YES Heated washing YES YES 2. Water Type Washing When using water type cleaning agents (e.g., terpene, and alkali saponifiers), select the cleaning agent based on the documentation issued by the various manufacturers of cleaning agents which describes the effects on metals and resins. Be careful that parts are not left with moisture remaining on them. 3. Washing Precautions Residual flux or cleaning agent on the contacts when washing with organic solvents or water type cleaners can give rise to the deterioration of electrical performance. In this regard it is important to check whether a thorough washing has been performed. C7