Multi Function POS SP-7260
|
|
- Louise Glenn
- 6 years ago
- Views:
Transcription
1 Multi Function POS SP-7260 User s Manual Edition: Jun 2014 Version 1.0
2 PREFACEE Federal Communications Commission (FCC) This equipment has been tested t andd found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCCC Rules. These T limits are designed to provide reasonable protection against harmful interferencee in a residential installation. This equipment generates, uses and can radiatee radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio orr televisionn reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following f measures: Reorient or relocate the receiving antenna. Increasee the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Declaration of Conformity These devices comply with part 15 of the FCC Rules. Operationn is subject to the following two conditions: 1. Thesee devices may not cause harmful interference. 2. Thesee devices must accept any interference received, including interference that may cause undesired operation. Lithium Battery Replace ement To avoid possible danger of explosion, ensuree correct polarity when changing the lithium battery. Replace only with the same or equivalent type recommended by the manufacturer. WEEEE (Waste from Electrical and Electronicc Equipment) The WEEE wheeled bin symbol on the product or on its packaging indicates that the product must not be disposed of with other waste. It should be the user s responsibility to dispose of their waste equipment by handing it over to an approved location for the recycling of waste electrical and electronic equipment. For more information about where to send your waste equipment for recycling, please contact your local city office, your household d waste disposal service or where you purchased the product. SP-7260 Multi Function POS II
3 Disclaimer PREFACE The material in this document is for information purpose and is subject to change without prior notice. APPOSTAR has made every effort to ensure that this user s manual is accurate and complete. However, no liability is assumed for any errors and omissions that may have occurred. Nor are any liability assumed for any damages resulting from the use of this product and the information contained in this document. APPOSTAR reserves the right to make improvements to this publication from time to time in the contents hereof without obligation of the manufacturer to notify any person of such revision or changes. Copyright This work is copyrighted. Reproduction or retransmission of this documentation, in whole or in part, without prior written permission from the manufacture is a violation of copyright law APPOSTAR Technology Co., Ltd. All rights reserved. Trademark Recognition 1. Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp. 2. Intel is a registered trademark of Intel International Inc. 3. Other software or product names used in this manual are the properties of their respective owners and are acknowledged. III SP-7260 Multi Function POS
4 PREFACE Important Safety Instructions Failure to observe these safety instructions may cause bodily injury, or damage to the product. Read these instructions carefully and keep this user s manual in an accessible location for future reference. The product may cause a fire or electric shock when it is used improperly. Observe the above safety measures at all times. If the product is damaged, immediately turn off the power and disconnect the power cord. Contact your dealer for assistance. 1. Do not plug in or unplug the power cord with wet hands. 2. Do not plug the product into an AC outlet with the incorrect voltage. (Be sure to use a voltage that is between AC 100V~240V) 3. Do not plug several products into one multi-outlet. 4. Do not apply pressure to the power cord or place heavy objects on it. 5. Immediately stop using the product if it emits strange noise, odor, or smoke. 6. Do not use aerosol sprayers containing flammable gas inside or around the product. 7. Do not allow foreign objects or liquids to enter the product, or serious damage may result. 8. Do not place the product on an unstable surface. The product may cause a fire if it is dropped, damaged, or broken. The following instructions will help you to make better use of this product. 1. Keep the machine away from locations subject to high humidity, dust, or temperatures that exceed the specification. (Refer to SEC. 1.4 Specification) 2. Clean the product only by using a dry cloth or a cloth soaked with detergent. Never use thinner or other volatile solvents for cleaning. 3. At the end of the day, clean and inspect the exterior of the machine after the machine is powered off. 4. Use only specified accessories. 5. Do not expose the accessories directly to sunlight, high temperatures, humidity, dust, or gas. 6. Do not place heavy objects on top of the product or lean them against the product. These items may fall down and cause injury. 7. Do not block the air vent of the product as this can cause heat accumulation inside the box machine and may cause a fire. SP-7260 Multi Function POS IV
5 Table of Contents CHAPTER 1 Product Overview Unpacking Appearance I/O Interface Specification... 6 CHAPTER 2 Hardware Installation Magnetic Stripe Reader (MSR) Installation... 7 CHAPTER 3 Software Installation Motherboard Driver Installation Peripheral Device Driver Installation... 9 CHAPTER 4 Board Setting Main Board Jumper Setting CHAPTER 5 INITIALIZING SCANNING BARCODES MAINTAINING CHAPTER 6 TROUBLESHOOTING APPENDIX General Scanner functionality USB Communication Decoding parameters Data formatting... 55
6 PRODUCT OVERVIEW CHAPTER 1 Product Overview Welcome The Multi Function POS series is the All-in-one POS Terminal which is conceptualized to save power consumption to meet the trend for green product. The features of Multi Function POS includes energy saving, s loww noise operation and highh performance value. The main board of Multi Function POS is skillfully embedded in the slim touch monitor. The compact and solidd stand gives you flexible working space arrangement. Up to five color options for the front panel are also providedd to match the mood of the operation environments. 1.1 Unpacking Confirm that all the following items are contained inn the carton. If any item is missing or damaged, contact the dealer from whom you y purchased the product. 1. POS Terminal Main Unit 2. Power Adapter 3. Power cord 4. Quick Reference Guide 5. Driver CD (User s Manual included) SP-7260 Multi Functionn POS 2
7 PRODUCT OVERVIEW 1.2 Appearance Front View 15 LCD touch panel MSR (optional) / Attachable on both sides Scanner Rear View I/O Cover 3 SP-7260 Multi Function POS
8 PRODUCT OVERVIEW Side View Tilt angle 0~90 degree Scanner View Scanner angle 0~66 degree SP-7260 Multi Function POS 4
9 1.3 I/O Interface PRODUCT OVERVIEW NO Port Description NO Port Description 1.5W integratedd SPEAKER speaker x 2 POWER On / Off switch DC-INPUT 12V DC-OUTPUTT 12V DC Jack DB15/F for second VGA-OUT display LANN COM 1 COM 2 COM 4 COM 5 LAN port with RJ45 Serial port with DB9/M connector Serial port with RJ45(5V default) Serial port with DB9/M connector Serial port with DB9/M connector DUAL USB USB 2. 0 Type A CASH DRAWER RJ11 with 12V NOTE: To avoid confusion with the LAN port, the COM 2 is protected with a lid. Remove the lid before use. 5 SP-7260 Multi Function POS
10 PRODUCT OVERVIEW 1.4 Specification System Main Board IAT CPU Intel Atom D GHz Dual Core Chipset Intel NM10 Express Chipset Main Memory 1GB DDRIII RAM Display Size 15 TFT-LCD with touch panel Display Resolution 1024 x 768 HDD 2.5 SATA HDD 320G Expansion Mini PCI Express Network 10/100M bps onboard Ethernet controller OS Compatibility Windows 7, Windows XP/XPE, POS Ready, Linux External I/O Interface Serial Port 4 x External COM Ports with 5V / 12V selectable Cash Drawer Port 1 x RJ 11 with DC 12V (single/dual) VGA Port 1 x VGA (DB15) Speaker 2 x Integrated 1.5 W stereo speaker Ethernet Port 1 x RJ45 10M / 100M / 1G Base-T USB Port 4 x USB 2.0 Type A DC output Jack 1 x 12V / 2.5A DC Jack Power Button 1 x power on/off switch Option Peripheral Magnetic Card Reader ISO 7811 option 1 / 2 / 3 track Fingerprint 512 dpi x 8 bit grayscale, Capture area:14.6 x 18.1 mm i-button Dallas Key Wireless LAN b/g Scanner Feature Light Source 650 nm VLD Depth of Field Up to mil / 0.33 mm, PCS 90% Scan Rate 2000 Scans per second Scan Pattern 6 direction scan field, 24 lines Resolution 5 mil / PCS 90 % Print contrast ratio 30% Indicator Beep and LED (Red:Standy by ; Green:Reading finished) Ambient light 4800 Lux Max Powering Power Supply AC 100V~240V / 60W power adapter Environment EMC & Safety CE/FCC Class A Operating Temperature 5 C ~ 40 C Storage Temperature -20 C ~ 60 C Operating Humidity 15%~80% RH Storage Humidity 20% ~90% RH Mechanical Housing Color Black Construction ABS + SECC Dimension (W x D x H) 355 x 240 x 390 mm Weight N.W 6.7kg SP-7260 Multi Function POS 6
11 CHAPTER 2 Hardware Installation HARDWARE INSTALLATION Before starting any hardware configuration, ensure that the system is powered off and the power cord is disconnected to prevent possible damage to the product. 2.1 Magnetic Stripe Reader (MSR) Installation An optional MSR can be installed on both right and left side of SP By default, the MSR is installed on the right side. Step 1 Remove the cover from the MSR extension slot. Step 2 Connect the MSR cable correctly. 7 SP-7260 Multi Function POS
12 SOFTWARE INSTALLATION CHAPTER 3 Software Installation This chapter describes the driver requirements and how to install the drivers from the driver CD. All step-by-step procedures described below are for Windows XP and similar on all other Microsoft Windows platforms. Insert the driver CD into your CD-ROM drive. Windows will automatically detect it and the Appostar Driver Installer appears on the screen. If not, locate the Setup.exe file at CD:\ and double-click it to execute the one-step driver installation. Follow the on-screen instructions to complete the installation. 3.1 Motherboard Driver Installation a. Click Install Motherboard Drivers. Select your model name and click Next to continue. b. Click Drivers icon on the upper left corner to continue. c. Select the Drivers option, including Chipset, Graphics, and LAN. Click Install to continue. d. Select Yes to reboot system. SP-7260 Multi Function POS 8
13 SOFTWARE INSTALLATION 3.2 Peripheral Device Driver Installation Touch Panel Driver Installation a. Click Touch Panel. b. Click Next on the Welcome screen to continue. c. Uncheck the Install PS/2 interface driver option. Click Next to continue. d. Select the Install RS232 interface driver option. Click Next to continue. e. Select the None option and click Next to continue. f. Select the Support Multi-Monitor System option. Click Next to continue. 9 SP-7260 Multi Function POS
14 SOFTWARE INSTALLATION g. Select the Destination Folder or use the default one listed. h. Type a Folder name or use the default one listed. Click Next to continue. i. A progress window appears. Please wait. j. Click Yes. The installation completes in seconds. SP-7260 Multi Function POS 10
15 CHAPTER 4 Board Setting BOARD SETTING 4.1 Main Board Jumper Setting JCMOS1: Clear CMOS Header * Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the mainboard. 1 3 Pin 1-2 Close: (Default) Normal Operation. 1 3 Pin 2-3 Close: Clear CMOS data. Clear CMOS Procedures: 1. Remove AC power line. 2. Set the jumper to Pin 2-3 close. 3. Wait for five seconds. 4. Set the jumper to Pin 1-2 close. 5. Power on the AC. 6. Reset your desired password or clear the CMOS data. JPC1/3/4/5/6: Voltage Switch jumper for JCOM1/3/4/5/6 ports This header is for controlling the Pin9 of COM ports to switch Ring/ 5V/12V. 2 1 Pin 1-2 Close: Pin9=5V 4 3 Pin 3-4 Close: Pin9=Ring (Default) 6 5 Pin 5-6 Close: Pin9=12V Remark: Max output: 12V@500mA for each COM port 11 SP-7260 Multi Function POS
16 BOARD SETTING JPC2 Voltage Switch jumper for JCOM2 ports This header is for controlling the Pin1of COM ports to switch Ring/ 5V/12V. 2 1 Pin 1-2 Close: Pin1=5V (Default) 4 3 Remark: Max output: 12V@500mA for each COM port Pin 3-4 Close: Pin1=Ring 6 5 Pin 5-6 Close: Pin1=12V JCOM2: Serial Port Connector Pin Assignment 1 COM2_RI 2 COM2C_DSR 3 COM2C_TXD 4 COM2C_RXD 5 COM2C_RTS 6 COM2C_CTS 7 GND 8 COM2C_DTR UATTENTION To avoid system malfunctions, DO NOT change the default setting by yourself. Contact your dealer for assistance if needed SP-7260 Multi Function POS 12
17 CHAPTER 5 INITIALIZING INITIALIZING When using this scanner for the first time, you need to initialize the communication. parameters first. Follow the steps below to initialize: 1. Power up POS. 2. Initialize the communication parameters by scanning the programming barcode 1.1 and 1.3 on the APPENDIX (A. Change Scanner Settings). NOTE The procedure is required only once. However, when changing the cable from one type to another, you need to perform the procedure again. 3. In USB mode, the scanner defaults to Keyboard Emulation Mode. This scanner transmits the data in International Keyboard layout (ALT-method) for communication. NOTE The USB must be directly connected to the host-usb port and not through an (un-powered) USB hub. 5.1 SCANNING BARCODES This scanner is an omni-directional presentation scanner featuring a 6 directional scan field with a 24-line scan pattern. Barcode labels can easily be read by presenting them to the scanner. NOTE Since this scanner is a presentation scanner, best results are obtained if the barcode is moved towards the scanner. 13 SP-7260 Multi Function POS
18 INITIALIZING 5.2 MAINTAINING This scanner requires little maintenance. Only occasional cleaning of the scanner window is necessary to remove dirt and fingerprints. Cleaning can be performed during operation with a non-abrasive glass spray cleaner and a soft lint-free cloth. SP-7260 Multi Function POS 14
19 CHAPTER 6 TROUBLESHOOTING TROUBLESHOOTING This section contains information on solving problems you may encounter when using the scanner. If troubles occur, take a moment to read the information in this section. However, before referring to the diagnostic tips ensure that the scanner is installed as described in Chapter 2 and that all cables are properly connected. Problem Diagnostic Tips The scanner window is dirty. Clean the scanner window as described in section 5.2. The scanner is on but a barcode cannot be read. The scanner does not accept more than two or three barcodes. A barcode is read by the scanner but not accepted by the host system. USB communication is not working. The presented barcode type is not enabled. Select the barcode type with the Configuration Guide. The scanner is disabled by the host. The barcode type you presented to the scanner is not supported by this scanner. There is no proper handshaking with the host system. Switch the host system on and check connection and communication settings. The communication cable is not connected to the serial port of your host system. Refer to the manual of your host system to locate the serial port. The communication settings of the host and scanner do not match. Ensure that the setting values for both devices are the same. For proper adjustment values, refer to the Configuration Guide. The communication cable does not suit your host system. Contact your supplier for the correct communication cable. The data format is not supported by the software running on the host system. In case of KB emulation you can select various keyboard languages or the universal Alt-input-method (default). You may want to try programming barcodes from section 3.4 on the Configuration Guide. In case of KB emulation in combination with the Alt-input method, check that Num-Lock of your keyboard is on. In MS-windows environment, verify with the device manager that the HID (Human Interface Device) is installed for the scanner. Check that the scanner and the host system both expect the same USB protocol (KB emulation, RS232 emulation or IBM POS protocol). See the Configuration Guide for setup codes and reset the scanner after making any changes. When using a standard-usb cable, the scanner defaults to the USB KB emulation protocol with ALT-method character transmission. When using USB plus power cable (with the green connector), the scanner defaults to USB-IBM-POS protocol for tabletop scanners. These settings are restored after programming back to default using the Configuration Guide. 15 SP-7260 Multi Function POS
20 APPENDIX Change Scanner Settings In order to change the scanner settings please follow the sequence below: 1. OPEN the scanner Programming Mode by scanning code CHANGE SCANNER SETTINGS by scanning any of the codes 2.1.x to 10.x.x. 3. CLOSE the scanner Programming Mode by scanning code 1.1. Reading the OPEN/CLOSE code 1.1 gives a double tone beep (Low High). An example: For changing the baudrate to 4800 the following codes must be scanned successively: After reading a valid barcode in Programming mode the scanner will give a High beep. The scanner will generate a Low beep after receiving an unexpected code. Reading a code, for example a predefined ASCII character, directly after entering the Programming Mode, is not allowed and the scanner will not accept this data. At any moment (in Programming Mode) you can scan code 1.2 to close the programming mode without update, or code 1.3 to return to default setting. SP-7260 Multi Function POS 16
21 Factory default settings SLEEP MODE DEFAULT Sleep mode After 10 minutes RS232 COMMUNICATION DEFAULT Baudrate 9600 Parity None Data bits 8 Stop bits 2 RTS/CTS Off Postamble <CR> KEYBOARD WEDGE COMMUNICATION DEFAULT Terminal type PC/AT Keyboard International (ALT Method) + Inter character delay 2 msec ++ Postamble Enter (alpha numeric) USB COMMUNCATION DEFAULT Mode USB Keyboard Emulation DECODER SELECTION DEFAULT EAN/UPC On (Add-On Off) Code 128/EAN 128 On Code 39 On Code 32 Off Codabar Off Interleaved 2/5 Off MSI Plessey Off Code 93 Off ISBN Off ISSN Off GS1 DataBar Off GS1 DataBar Expanded Off DECODER CONFIGURATION DEFAULT Min. length Interleaved 2/5 8 CODE IDENTIFIERS DEFAULT Code identifiers Off NOTE: + In Asian Mode, it is set at US Keyboard. ++ In Asian Mode, it is set at 0 msec. APPENDIX 17 SP-7260 Multi Function POS
22 Default message format CODE MESSAGE FORMAT EAN13 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11D12 D13 EAN8 D1 D2 D3 D4 D5 D6 D7 D8 UPCA D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11D12 UPCE 0 D1 D2 D3 D4 D5 D6 Code 128 D1 - Dx EAN 128 ]C1 D1 - Dx Code 39 D1 - Dx Code 32 D1 - Dx Codabar D1 - Dx Interleaved 2/5 D1 - Dx MSI Plessey D1 - Dx Code 93 D1 - Dx ISBN D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 ISSN D1 D2 D3 D4 D5 D6 D7 D8 GS1 DataBar D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11D12 D13 GS1 DataBar DD11-4D74 (numeric) D1- D42 (alphanumeric) Expanded Important: Please note that EAN/UPC codes with Add-On are transmitted without a separator. Programming flow chart CHANGE SCANNER SETTINGS OPEN PROGRAMMING MODE BY SCANNING CODE 1.1 CHANGE SCANNER SETTINGS BY SCANNING CODE 2.1.x 10.x.x CLOSE PROGRAMMING MODE BY SCANNING CODE 1.1 SAVE AND EXIT SP-7260 Multi Function POS 18
23 1. General 1.1 OPEN PROGRAMMING MODE OR CLOSE PROGRAMMING MODE WITH UPDATE CLOSE PROGRAMMING MODE WITHOUT UPDATE SP-7260 Multi Function POS
24 1.3 RETURN TO FACTORY DEFAULT SETTINGS 1.3 Use this code to return to the original factory default setting. Important: Programming Mode is closed after scanning this code. 1.8 EMEA MODE 1.8 Note: For European, Middle East and African countries, read the following bar codes to set in EMEA mode SP-7260 Multi Function POS 20
25 1.9 ASIA MODE Note: For Asian and other countries (except European, Middle East and African countries), read the following bar codes to set in Asia mode FIRMWARE VERSION 1.15 Note: Output the firmware version by read the following bar codes: SP-7260 Multi Function POS
26 2. Scanner functionality 2.1 Speaker settings SPEAKER FERQUENCY Note: Repeat reading this bar code to obtain different tone SPEAKER VOLUME Note: Repeat reading this bar code to obtain different volume. SP-7260 Multi Function POS 22
27 2.2 Sleep mode SLEEP MODE OFF Note: This setting will reduce the product life time SLEEP MODE AFTER 10 MINUTES (DEFAULT) SP-7260 Multi Function POS
28 2.2.3 SLEEP MODE AFTER 30 MINUTES SLEEP MODE AFTER 60 MINUTES SP-7260 Multi Function POS 24
29 2.3 Scanner timing SAME CODE DELAY 300MSEC SAME CODE DELAY 600MSEC SP-7260 Multi Function POS
30 3. USB Communication 3.1 USB SETTINGS For scanners with integrated USB-interface, you may activate this interface by connecting to appropriate communication cable. Depending on the firmware version of the scanner, various protocol versions may be possible: 1. USB Keyboard Emulation (default) 2. USB IBM fixed POS scanner 3. USB IBM handheld scanner emulation Important: Reset (re-power) the scanner after changing one of the options listed above USB KEYBOARD EMULATION (DEFAULT) USB IBM FIXED POS SCANNER SP-7260 Multi Function POS 26
31 3.1.3 USB IBM HANDHELD SCANNER EMULATION USB COMPORT EMULATION SP-7260 Multi Function POS
32 4. Decoding parameters 4.1 Decoder selection EAN/UPC ON + ADDON OFF (DEFAULT) EAN/UPC OFF + ADDON OFF SP-7260 Multi Functionn POS 28
33 4.1.3 EAN/UPC ON + ADDON ON Note: Important: Add-On codes are optional. The scanner will accept bar codes with or without Add-On. If the scanner reads an EAN/UPC code without Add-On, the scanner will look for a certain extra time for an Add-On. If this time has elapsed and no Add-On is found, the scanner will just send the EAN/UPC main code EAN/UPC + ADDON MANDATORY ON (FOR378/379/414/419/434/439/529/977) SP-7260 Multi Function POS
34 CODE 128/EAN 128 ON CODE 128/EAN 128 OFF SP-7260 Multi Function POS 30
35 CODE 39 ON CODE 39 FULL ASCII ON SP-7260 Multi Function POS
36 CODE 32 ON CODE 39/CODE 32 OFF SP-7260 Multi Function POS 32
37 CODABAR ON CODABAR OFF SP-7260 Multi Function POS
38 INTERLEAVED 2/5 ON It is mandatory to select a minimum code length using the appropriate bar code in paragraph 4.2 to prevent short reads INTERLEAVED 2/5 OFF SP-7260 Multi Function POS 34
39 MSI PLESSEY ON MSI PLESSEY OFF SP-7260 Multi Function POS
40 CODE 93 ON CODE 93 OFF SP-7260 Multi Function POS 36
41 ISBN ON ISBN OFF SP-7260 Multi Function POS
42 ISSN ON ISSN OFF SP-7260 Multi Function POS 38
43 GS1 DATABAR ON GS1 DATABAR OFF SP-7260 Multi Function POS
44 GS1 DATABAR EXPANDED ON GS1 DATABAR EXPANDED OFF SP-7260 Multi Function POS 40
45 GS1 DATABAR LIMITED ON GS1 DATABAR LIMITED OFFF SP-7260 Multi Function POS
46 4.2 Decoder configuration Programming flow chart for minimum length off bar code PROGRAMMING MINIMUM LENGTH OF BAR CODE SET MINIMUM LENGTH OF BAR CODE (SCAN CODE 4.2.1~ ) LENGTH (SCAN CODE ~ ) SAVE AND EXIT SET MIN. LENGTH CODE SET MIN. LENGTH CODE SP-7260 Multi Functionn POS 42
47 4.2.3 SET MIN. LENGTH CODABAR R SET MIN. LENGTH INTERLEAVED 2/ SP-7260 Multi Function POS
48 SET MIN. LENGTH MSI Plessey SET MIN. LENGTH CODE SP-7260 Multi Functionn POS 44
49 LENGTH = LENGTH = SP-7260 Multi Function POS
50 LENGTH = LENGTH = SP-7260 Multi Functionn POS 46
51 LENGTH = LENGTH = SP-7260 Multi Function POS
52 LENGTH = LENGTH = SP-7260 Multi Functionn POS 48
53 LENGTH = LENGTH = SP-7260 Multi Function POS
54 LENGTH = LENGTH = SP-7260 Multi Functionn POS 50
55 LENGTH = LENGTH = SP-7260 Multi Function POS
56 4.3 Japanese book code DISABLE 978/192 JAPANESEE BOOK CODE(DEFAULT) ENABLE 978/192 JAPANESE BOOK CODE SP-7260 Multi Functionn POS 52
57 4.3.5 ENABLE JAPANESE BOOK CODE SEPARATOR (DEFAULT)) DISABLE JAPANESE BOOK CODE SEPARATOR SP-7260 Multi Function POS
58 4.3.7 OPEN PROGRAMMING JAPANESE BOOK CODE SEPARATOR (ONE CHARACTER) Note: Only one separator is available. To set Japanese book code separator, scan: ASCII code 1.1 SP-7260 Multi Function POS 54
59 5. Data formatting 5.1 Preambles Programming sequence preambles The scanner can be programmed to output bar code data according to the following format: [PREAMBLE STRING BAR CODE DATA] APPENDIX The preamble string is limited to a maximum length of 3 characters. Use the chart on the next page to program the preamble string. Example: To send a <STX> in front of the bar code, scan successively (while in Programming Mode) Free programmable preambles : Open Programming mode <STX> Free programmable preambles : Close programming mode with update As a result, the scanner will give the following bar code data output: 55 SP-7260 Multi Function POS
60 Programming flow chart preambles PROGRAMMMING PREAMBLE STRING OPEN PROGRAMMING MODE FREE PROGRAMMABLE PREAMBLES (SCAN CODE 5.1.1) SELECT PREAMBLE CHARACTER (SCAN CODE 10.1.X) Yes NUMBER OF PREAMBLE CHARACTERS = 3? SAVE AND EXIT NO MOREPREAMBLE CHARACTERS TO BE PROGRAMMED? Yes NO Yes SAVE PROGRAMMED DATA? NO CLOSE PROGRAMMING FREE PROGRAMMABLE PREAMBLES WITHOUT UPDATE (SCAN CODE 5.1.1) CLOSE PROGRAMMING MODE FREE PROGRAMMABLE PREAMBLES WITH UPDATE (SCAN CODE 5.1.2) EXIT SAVE AND EXIT SP-7260 Multi Function POS 56
61 5.1.1 FREE PROGRAMMABLE PREAMBLES: OPEN PROGRAMMING MODE / CLOSE PROGRAMMING MODE WITHOUT UPDATE FREE PROGRAMMABLE PREAMBLES: CLOSE PROGRAMMING MODE WITH UPDATE SP-7260 Multi Function POS
62 5.2 Postambles Programming sequence preambles The scanner can be programmed to output bar code data according to the following format: [BAR CODE DATA] [POSTAMBLE STRING] The preamble string is limited to a maximum length of 3 characters. Use the chart on the next page to program the preamble string. Example: To send a <ETX>after of the bar code, scan successively (while in Programming Mode) Free programmable preambles : Open Programming mode <ETX> Free programmable preambles : Close programming mode with update As a result, the scanner will give the following bar code data output: SP-7260 Multi Function POS 58
63 Programming flow chart preambles APPENDIX PROGRAMMMING PREAMBLE STRING OPEN PROGRAMMING MODE FREE PROGRAMMABLE PREAMBLES (SCAN CODE 5.2.5) SELECT PREAMBLE CHARACTER (SCAN CODE 10.1.X) Yes SAVE AND EXIT NUMBER OF PREAMBLE CHARACTERS = 3? NO MOREPREAMBLE CHARACTERS TO BE PROGRAMMED? Yes NO SAVE PROGRAMMED DATA? Yes NO CLOSE PROGRAMMING FREE PROGRAMMABLE PREAMBLES WITHOUT UPDATE (SCAN CODE 5.2.5) CLOSE PROGRAMMING MODE FREE PROGRAMMABLE PREAMBLES WITH UPDATE (SCAN CODE 5.2.6) EXIT SAVE AND EXIT 59 SP-7260 Multi Function POS
64 5.2.1 PREDEFINED POSTAMBLE = CR(DEFAULT) PREDEFINED POSTAMBLE = LF SP-7260 Multi Function POS 60
65 5.2.3 PREDEFINED POSTAMBLE = CR + LF FREE PROGRAMMABLE POSTAMBLES: OPEN PROGRAMMING MODE / CLOSE PROGRAMMING MODE WITHOUT UPDATE SP-7260 Multi Function POS
66 5.2.6 FREE PROGRAMMABLE POSTAMBLES: CLOSE PROGRAMMING MODE WITH UPDATE Code identifiers Set message format with code identifiers A code identifier is a data string, giving information to the host system concerning the bar code type that has been read. After scanning code 5.3.1, the scanner is programmed to transmit data according to the following format: CODE CODE MESSAGE FORMAT EAN13 F D1 - D13 EAN8 FF D1 - D8 UPCA A D1 - D12 UPCE E 0 D1 - D6 Code 128 # D1 - Dx EAN 128 P ]C1 D1 - Dx Code 39 * D1 - Dx Code 32 * D1 - Dx Codabar % D1 - Dx Interleaved 2/5 i D1 - Dx MSI Plessey O D1 - Dx Code 93 L D1 - Dx ISBN F D1 - D10 ISSN F D1 - D8 GS1 DataBar U D1 - D14 GS1 DataBar Expanded W D1 - D74 (numeric) or D1 - D42 (alphanumeric) Important: Please note that the UPCE format will be changed. The scanner will transmit UPCE codes with leading zero and without check digit. To return to default format without code identifiers scan code SP-7260 Multi Function POS 62
67 5.3.1 SET MESSAGE FORMAT WITH CODE IDENTIFIERS SET MESSAGE FORMAT WITHOUT CODE IDENTIFIERS SP-7260 Multi Function POS
68 2 versions of preset code identifier are available. The comparison between default version and Datalogic version is listed below. Default Datalogic EAN13 F F EAN8 FF FF UPCA A A UPCE E E Code 128 # # EAN 128 P Null(none) Code 39 * * Code 32 * p ITF 25 i l Codabar % % Code 93 L & MSI/PLESSY DataBar Omni-directional U R4 DataBar Limted V RL DataBar Expanded W RX Note: Scan code for Datalogic version. *Datalogic is the trade mark of Datalogic S.p.A. SP-7260 Multi Function POS 64
69 5.3.3 DEFAULT CODE IDENTIFIER DATALOGIC CODE IDENTIFIER SP-7260 Multi Function POS
70 Programming flow chart for setting codee identifier PROGRAMMING CODE IDENTIFIER SET IDENTIFIER OF BAR CODE (SCAN CODE ~ ) ASCII CODE (SCAN CODE ~ ) EXIT PROGRAMMING IDENTIFIER WITH UPDATE (SCAN CODE ) SAVE AND EXIT SETTING IDENTIFIER EAN SETTING IDENTIFIER EAN SP-7260 Multi Functionn POS 66
71 SETTING IDENTIFIER UPCAA SETTING IDENTIFIER UPCE SP-7260 Multi Function POS
72 SETTING IDENTIFIER EAN SETTING IDENTIFIER CODE SP-7260 Multi Functionn POS 68
73 SETTING IDENTIFIER CODE SETTING IDENTIFIER CODE SP-7260 Multi Function POS
74 SETTING IDENTIFIER CODABAR SETTING IDENTIFIER INTERLEAVED 2/ SP-7260 Multi Functionn POS 70
75 SETTING IDENTIFIER MSI/ /PLESEY SETTING IDENTIFIER CODE SP-7260 Multi Function POS
76 EXIT PROGRAMMING FREE PROGRAMMABLE IDENTIFII ER WITH UPDATE EXIT PROGRAMMING FREE UPDATE PROGRAMMABLE IDENTIFII ER WITHOUT SP-7260 Multi Functionn POS 72
77 5.4 Code representation UPCA FORMAT TRANSMITTED AS UPCA (12 DIGITS) UPCA FORMAT TRANSMITTED AS EAN13 (WITHH LEADING ZERO) SP-7260 Multi Function POS
78 5.4.5 UPCA FORMAT UPCE TO UPCAA EXPANSION ON UPCA FORMAT UPCE TO UPCAA EXPANSION OFF SP-7260 Multi Functionn POS 74
79 5.4.7 UPCE FORMAT WITH LEADING ZERO UPCE FORMAT WITHOUT LEADING ZERO SP-7260 Multi Function POS
80 5.4.9 UPCE FORMAT WITH CHECK DIGIT UPCE FORMAT WITHOUT CHECK DIGIT SP-7260 Multi Function POS 76
81 EAN 128 CODE INDENTIFIER ]C1 ON EAN 128 CODE INDENTIFIER ]C1 OFF SP-7260 Multi Function POS
82 TRANSMITT EAN8 CHECKDIG GIT ON TRANSMITT EAN8 CHECKDIG GIT OFF SP-7260 Multi Functionn POS 78
83 TRANSMITT EAN13 CHECKDIGIT ON TRANSMITT EAN13 CHECKDIGIT OFF SP-7260 Multi Function POS
84 TRANSMITT UOCA CHECKDIG GIT ON TRANSMITT UPCA CHECKDIG GIT OFF SP-7260 Multi Functionn POS 80
85 EXPAND EAN8 TO UPCA ON EXPAND EAN8 TO UPCA OFF SP-7260 Multi Function POS
86 TRANSMITT FIRST DIGIT UPCA OFF TRANSMITT FIRST DIGIT UPCA ON SP-7260 Multi Functionn POS 82
87 TRANSMISSION OF THE CHECK CHARACTER AT CODE39 OFF TRANSMISSION OF THE CHECK CHARACTER AT CODE39 ON SP-7260 Multi Function POS
88 VERIFICATION OF THE CHECK CHARACTER AT A CODE39 OFF VERIFICATION OF THE CHECK CHARACTER AT A CODE39 ON SP-7260 Multi Functionn POS 84
89 TRANSMISSION OF THE CHECK CHARACTER AT CODABAR OFF TRANSMISSION OF THE CHECK CHARACTER AT CODABAR ON SP-7260 Multi Function POS
90 VERIFICATION OF THE CHECK CHARACTER AT A CODABAR OFF VERIFICATION OF THE CHECK CHARACTER AT A CODABAR ON SP-7260 Multi Functionn POS 86
91 TRANSMISSION OF THE CHECK DIGIT AT INTERLEAVED 2/5 OFF TRANSMISSION OF THE CHECK DIGIT AT INTERLEAVED 2/5 ON SP-7260 Multi Function POS
92 VERIFICATION OF THE CHECK DIGIT AT INTERLEAVEDD 2/5 OFFF VERIFICATION OF THE CHECK DIGIT AT INTERLEAVEDD 2/5 ON SP-7260 Multi Functionn POS 88
93 VERIFICATION MSI/PLESSEY CHECK DIGIT OFF O VERIFICATION MSI/PLESSEY CHECK DIGIT ON O SP-7260 Multi Function POS
94 TRANSMISSION OF THE CHECK DIGIT AT ISBN OFF TRANSMISSION OF THE CHECK DIGIT AT ISBN ON SP-7260 Multi Functionn POS 90
95 DO NOT TRANSMITT START/ /STOP AT CODE TRANSMITT START/ /STOP AT CODE SP-7260 Multi Function POS
96 DO NOT TRANSMIT START/STOP CODABAR SP-7260 Multi Functionn POS 92
97 B. Predefined ASCII characters SOH STX SP-7260 Multi Function POS
98 ETX EOT SP-7260 Multi Function POS 94
99 C. Special keys On the following pages you find some special key programming bar codes, related to KBW communication. These codes are also applicable in USB interface with USB keyboard emulation TAB ENTER (ALPHANUMERIC) SP-7260 Multi Function POS
100 ENTER (NUMERIC) SP-7260 Multi Function POS 96
Multi Function POS SP-7262
http://www.appostar.com Multi Function POS SP-7262 User s Manual Edition: Jun 2015 Version 0.9 PREFACEE Federal Communications Commission (FCC) This equipment has been tested t andd found to comply with
More informationC O N F I G U R A T I O N G U I D E
C O N F I G U R A T I O N G U I D E Copyright @ 2013, This manual is copyrighted, with all right reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced,
More informationC O N F I G U R A T I O N G U I D E
C O N F I G U R A T I O N G U I D E Copyright @ 2013, This manual is copyrighted, with all right reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced,
More informationTable of contents. Change scanner settings Factory default settings Default message format Programming flow chart
Table of contents Change scanner settings Factory default settings Default message format Programming flow chart 1. General 1.1 Open programming mode or Close programming mode with update 1.2 Close programming
More informationOmni-Directional Barcode Scanner Model No. OM7120
Omni-Directional Barcode Scanner Model No. OM7120 User s Manual Programming with barcodes The BARCODE PROGRAMMING feature gives the possibility to change scanner settings without any tools or dismounting
More informationProgramming with barcodes
Configuration Guide Programming with barcodes The BARCODE PROGRAMMING feature gives the possibility to change the Scantech scanner settings without any tools or dismounting the scanner from the check stand.
More informationC O N F I G U R A T I O N G U I D E
C O N F I G U R A T I O N G U I D E Copyright @ 2009, This manual is copyrighted, with all right reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced,
More information2190 POS System User Guide
2190 POS System 2190 User Guide Thank you for selecting UTC RETAIL s innovative Model 2190 Point of Sale solution! This guide is designed to acquaint you with the features and functionality of the 2190
More information2100 POS System User Guide
2100 POS System 2100 User Guide Thank you for selecting UTC RETAIL s innovative Model 2100 Point of Sale solution! This guide is designed to acquaint you with the features and functionality of the 2100
More informationNuscan 3200 Optical Laser Barcode Scanner
Nuscan 3200 Optical Laser Barcode Scanner Programming Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
More informationManual de Programación
Manual de Programación SM2410, SM2410B, SM2420 y SM2430 ESPECIFICACIONES SUJETAS A CAMBIO SIN PREVIO AVISO. Enter/Exit Programming Mode (This barcode is also found at page 8.) IMPORTANT NOTICE Every effort
More informationMini Wireless Barcode Reader Quick Guide
Mini Wireless Barcode Reader Quick Guide Full user s manual is available on the enclosed CD. Mini Wireless Barcode Reader Quick Guide P/N: 8002-0028*00 FCC WARNING STATEMENT This equipment has been tested
More informationMagnetic Stripe Reader SERIES 1290 Operation Manual
Magnetic Stripe Reader SERIES 1290 Operation Manual Version 2.0 This equipment has been tested and found to comply with the limits for Class A digital device. Pursuant to Part 15 of the FCC Rules. These
More informationThe following symbols are used to show dangerous operation or handling. Make sure you understand them before reading the guide.
Safety Instructions Before use Thank you very much for purchasing this product. This product is an interface box called "Connection & Control Box" for EPSON short throw projectors. For your safety, read
More informationThe following symbols are used to show dangerous operation or handling. Make sure you understand them before reading the guide.
Safety Instructions Before use Thank you very much for purchasing this product. This product is an interface box called "Connection & Control Box" for EPSON short throw projectors. For your safety, read
More informationMultiPlex 15 Touch Screen. User s Manual
MultiPlex 5 Touch Screen User s Manual Preface Precautions. READ INSTRUCTIONS: All the safety and operating instructions should be read before the LCD monitor is operated.. RETAIN INSTRUCTIONS: The safety
More informationThank you for selecting UTC RETAIL s innovative Model 1170 Point of Sale solution!
1170 POS SYSTEM 1170 USER GUIDE Thank you for selecting UTC RETAIL s innovative Model 1170 Point of Sale solution! This guide is designed to acquaint you with the features and functionality of the 1170
More informationEVO-TP Hardware System
User Manual Revision v1.3 February 2010 EVO-TP Hardware System Copyright 2009 February All Rights Reserved Manual Version 1.1 Part Number: The information contained in this document is subject to change
More informationUser Manual Version V1.1 March Elios Point-of-Sale Hardware System
User Manual Version V1.1 March 2010 Elios Point-of-Sale Hardware System Copyright 2009~2010 All Rights Reserved Manual Version 1.1 The information contained in this document is subject to change without
More information4170 POS System Installation Guide
4170 POS System 4170 Installation Guide Thank you for selecting UTC RETAIL s innovative Model 4170 Point of Sale solution! This Installation Guide will help you efficiently install the 4170 POS. The document
More informationUser Manual Infinity:One
User Manual Infinity:One For the latest updates and information, please visit: support.one-education.org Notice The information in this user s manual is protected by copyright laws, all parts of this manual,
More informationChromebook Owner s Manual
CMT Chromebook Owner s Manual Before using, please read these operating instructions carefully. They contain important advice concerning the use and safety of your Chromebook. Use for its intended purpose
More informationChromebook Owner s Manual
Chromebook Owner s Manual Before using, please read these operating instructions carefully. They contain important advice concerning the use and safety of your Chromebook. Use for its intended purpose
More informationMIL-STD Rugged Computer User's Manual. Version 1.0 Revision Date: July. 05, 2017 THOR200. MIL-STD Rugged Computer
THOR200 MIL-STD Rugged Computer Safety information Electrical safety To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. When adding
More informationMagnetic Stripe Reader SERIES 1290
Magnetic Stripe Reader SERIES 1290 Operation Manual Version 1.0 This equipment has been tested and found to comply with the limits for Class A digital device. Pursuant to Part 15 of the FCC Rules. These
More informationNetwork Camera. Quick Guide DC-B1203X. Powered by
Network Camera Quick Guide DC-B1203X Powered by Safety Precautions English WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE
More informationwireless barcode scanner X-620 User Manual
wireless barcode scanner X-620 User Manual V:1.0 Performance Strong decoding capability Rugged housing design Proprietary intellectual property Comfortable and convenient to use long life time button--3
More information2D Image Handheld Scanner
1 Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0 9/6/2018 Initial release i Important Notice No warranty of any kind is made in regard to this
More informationFZ-VEBG11x. Cradle. Model No. FZ-VEBG11 1. Model No. U Universal R China 1: Area U: Universal R: China
ORDER NO. CPD1306201CE Cradle Model No. FZ-VEBG11x This is the Service Manual for the following areas. U for Universal R for China Model No. FZ-VEBG11 1 U Universal R China 1: Area U: Universal R: China
More information4100 POS System User Guide
4100 POS System 4100 User Guide Thank you for selecting UTC RETAIL s innovative Model 4100 Point of Sale solution! This guide is designed to acquaint you with the features and functionality of the 4100
More informationCOPYRIGHT 2009,SCSC. Manual P/No: SCCM - 80S-01A Released Date: Oct 31, 2009
To begin the configuration procedures Thank you for purchasing the scanner. Inside each packaging box, you may find the scanner, the interface cable and user's fuide. Configuration manual might be optional
More informationSmartphone Photo Printer
Smartphone Photo Printer Safety Precautions Safety Precautions Denotes the possibility of serious injury or death Please keep you away at least 20cm distance from printer when printing. Use only recommended
More informationUSER MANUAL VERSION V1.0 AUG MiniPOS Hardware System
USER MANUAL VERSION V1.0 AUG 2010 MiniPOS Hardware System Copyright 2010 August All Rights Reserved Manual Version 1.0 Part Number: 3LMPPA530110 The information contained in this document is subject to
More informationAvailable in 2.0MP, 4.0MP, 6.0MP and 8.0MP, with 2.8mm and 3.6mm lenses.
Camera Quick Install Guide VDMINIIRCB Series Available in 2.0MP, 4.0MP, 6.0MP and 8.0MP, with 2.8mm and 3.6mm lenses. Thank you for purchasing a VDMINIIRCB Series CCTV Surveillance Camera. This Quick Install
More informationUser manual Model: VIU-800 Brand:
User manual Model: VIU-800 Brand: - 1 - This manual s main purpose is to introduce the correct way of using the Voter Identification Unit / Electronic Voting Machine (hereinafter referred to as "the device").
More informationUser s Manual WARNING CIPHER 1000 CCD SERIES
CIPHER 1000 CCD SERIES User s Manual WARNING This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed
More informationPlease read this guide before using the printer
PD-450/450W/480/480W User Guide Please read this guide before using the printer Safety Precautions Safety Precautions Denotes the possibility of serious injury or death Use only recommended power sources.
More informationAvailable in 2.0MP, 4.0MP and 8.0MP variants
Camera Quick Install Guide FBMINIIR Series Available in 2.0MP, 4.0MP and 8.0MP variants Thank you for purchasing a FBMINIIR Series CCTV Surveillance Camera. This Quick Install Guide covers basic setup,
More informationITA-1711 Series Fanless Compact Embedded IPC with Intel Celeron Dual Core CPU Startup Manual
ITA-1711 Series Fanless Compact Embedded IPC with Intel Celeron Dual Core CPU Startup Manual Packing List Specifications Before you begin installing your IPC, please make sure that the following items
More informationWelcome 1. Precaution
0 Table of Contents 1. Precautions. 2 2. Preparation.. 2 Standard Accessories.. 5 Parts Names.. 6 Charging the Battery Pack..... 7 3. Recording Mode 9 Loading SD card 9 Connect External Camera.. 9 Powering
More informationQuick Installation Guide
Quick Installation Guide Applicable Models: AS3102T/AS3104T/AS3202T/AS3204T Ver.2.5.0128 (2016-1-28) Table of Contents Notices... 3 Safety Precautions... 4 1. Package Contents... 5 2. Optional Accessories...
More informationQuick Installation Guide
Quick Installation Guide For Network Attached Storage Ver.1.1.0.0320 Table of Contents Notices... 3 Safety Precautions... 4 1. Package Contents... 5 2. Hardware Installation Guide... 6 2.1. Hard Disk Installation...
More informationSPK User Manual. 900MHz Wireless Stereo Headphones INTRODUCTION FEATURES IMPORTANT SAFETY INFORMATION
INTRODUCTION Thank you for purchasing our 900Mhz compact cordless stereo headphone system that takes advantage of the very latest advances in wireless transmission technology so you SPK-9100 900MHz Wireless
More information3190 Series Touch Screen POS Workstation
3190 Series Touch Screen POS Workstation INSTALLATION GUIDE Congratulations on your purchase of UTC RETAIL s innovative 3190 Series Touch Screen POS Workstation. The 3190 Series is designed for use in
More informationUSER MANUAL 10 Multi-Touch Panel PC
Rev 1.0 May, 2013 USER MANUAL 10 Multi-Touch Panel PC IPW10ID3S-H1-PoE-PCT American Industrial Systems, Inc. http://www.aispro.com Quick solution for: Room Booking Schedule Access Control Room Information
More informationSB1015W Widescreen All-in-one POS Terminal USER MANUAL
SB1015W Widescreen All-in-one POS Terminal USER MANUAL Table of Contents 1 Introduction...2 1.1 Safety Information... 2 1.2 Electromagnetic compatibility statement... 3 2 Overview... 4 2.1 Features...
More information2D Image Hands-Free Scanner
8072 1 Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0 03/24/2016 Initial release i Important Notice No warranty of any kind is made in regard
More informationUser s guide for Xtenda TM
User s guide for Xtenda TM (X300 Series) Copyright by Ncomputing Co. Ltd. 2004. - Illegal copying of this software, hardware and this documentation is prohibited by law. All other brand- and product names
More informationPA Series. Available in 6.0MP and 8.0MP
Camera Quick Install Guide PA Series Available in 6.0MP and 8.0MP Thank you for purchasing a PA Series CCTV Surveillance Camera. This Quick Install Guide covers basic setup, installation and use of your
More informationPOS500/505 with B75 M/B Installation Guide Point-of-Sale Hardware System
POS500/505 with B75 M/B Installation Guide Point-of-Sale Hardware System 48200280 July 2003 V1.0 1. Accessory External Floppy Cable External IDE Cable Power Cord Y Cable(Keyboard & Mouse) Serial Cable
More informationProgrammable Keyboard SERIES 8031 S
Programmable Keyboard SERIES 8031 S Operation Manual Version 1.0 This equipment has been tested and found to comply with the limits for Class A digital device. Pursuant to Part 15 of the FCC Rules. These
More informationSafety and Maintenance You can use your Tablet PC under a wide range of environmental conditions. However, to ensure long use and continued high
EVG7 DL46 Getting Started Congratulations on your purchase of a Tablet PC. The Tablet PC is a fully functional PC with built-in LAN, and wireless connectivity. With your Tablet PC you will be able to organize
More informationTWINHEAD. Plug-In PC - PLUGTH series for Panasonic Professional Displays. Operating Instructions. PN1H (Model number PLUGTH series) English
TWINHEAD English PN1H (Model number PLUGTH series) Plug-In PC - PLUGTH series for Panasonic Professional Displays Operating Instructions Before connecting, operating, or adjusting this product, please
More informationQuick Installation Guide
Quick Installation Guide For Network Attached Storage Ver.1.1.0.0517 Table of Contents Notices... 3 Safety Precautions... 4 1. Package Contents... 5 2. Hardware Installation Guide... 6 2.1. Hard Disk Installation...
More informationTable of Contents. Federal Communications Commission (FCC) Statement...2
Contents Table of Contents Federal Communications Commission (FCC) Statement...2 Important Safety Instructions...3 Chapter 1 Introduction Features...6 Package Contents...7 Front View and Controls...8 Installing
More informationUser Guide PCT Multi Touch Monitor Display OF17T100-A1-PCT
User Guide PCT Multi Touch Monitor Display OF17T100-A1-PCT American Industrial Systems - OF17T100-A1-PCT User Guide Page 1 The information contained in this document is subject to change without notice.
More informationW10 PRO QUICK START GUIDE
W10 PRO QUICK START GUIDE GETTING STARTED Thank you for purchasing a Hipstreet product and we hope you enjoy using it. Please visit our website at www.hipstreet.com IMPORTANT SAFETY PRECAUTIONS Always
More informationLaser Barcode Scanner ARP Nr User s Manual
Laser Barcode Scanner ARP Nr. 853782 User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
More informationLCD monitor $ *- & 86 LR60441
LCD monitor B286HK MHL USB 2 USB Acer LCD Monitor Quick Start Guide (QSG) Important safety instructions Please read the following instructions carefully. 1. To clean the LCD monitor screen: Turn off the
More informationUser Guide Widescreen PCT Multi Touch Monitor Display DTW15T100-A1-PCT
User Guide Widescreen PCT Multi Touch Monitor Display DTW15T100-A1-PCT American Industrial Systems - DTW15T100-A1-PCT User Guide Page 1 The information contained in this document is subject to change without
More informationUSB to Serial Converter User s Guide
USB to Serial Converter User s Guide Important Note! In order to minimize possible installation problems and/or resource conflicts: Read Me First! About This User s Guide This User s Guide is designed
More informationMS810 Laser Scanner. Product Reference Guide. Rev. A
MS810 Laser Scanner Product Reference Guide Rev. A 1 Preface About This Manual This manual explains how to install, operate and maintain the Unitech MS810 Laser Scanner. No part of this publication may
More informationMS810 Laser Scanner. Product Reference Guide. Rev. A
MS810 Laser Scanner Product Reference Guide Rev. A 1 Preface About This Manual This manual explains how to install, operate and maintain the Unitech MS810 Laser Scanner. No part of this publication may
More information4 Port KVM Switch. If anything is damaged or missing, contact your dealer.
4 Port KVM Switch User Manual CS-84A Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the units and/or any devices that connect
More informationProjection Laser Scanner SERIES 2600
ISO 9002 Certified Lead with technology Win customers with service Projection Laser Scanner SERIES 2600 OPERATION MANUAL OPERATION MANUAL Laser Safety The 2600 laser scanner complies with safety standard
More informationDLL2020. Software Configuration Manual
DLL2020 Software Configuration Manual DLL2020 SOFTWARE CONFIGURATION MANUAL DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italia DLL2020 Software Configuration Manual Ed.:02/2003
More informationUser Manual. TEOS Hardware System. November 2011 Revision 1.2 TEOS 1218/1216D TEOS 1518/1516D TEOS 1718/1716D TEOS 1918/1916D
User Manual November 2011 Revision 1.2 TEOS Hardware System TEOS 1218/1216D TEOS 1518/1516D TEOS 1718/1716D TEOS 1918/1916D Copyright 2007~2011. All Rights Reserved Manual Version 1.2 The information contained
More informationPOS Terminal NP-3264 User s Manual Edition: NOV 2012 Version 1.02
http://www.appostar.com POS Terminal NP-3264 User s Manual Edition: NOV 2012 Version 1.02 PREFACE Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits
More informationUser s Manual 131 Tiny III Decoder
User s Manual 131 Tiny III Decoder Document Number : 131-0114 Release Date : Mar 16, 1998 1998, SYNTECH INFORMATION Co., Ltd.. All rights reserved. CipherLab is a registered trademark of SYNTECH INFORMATION
More informationf200 English User Manual Contents
f200 English User Manual Contents About this Guide...3 FCC Statement...3 WEEE Notice...3 CE Regulatory Notice...4 Notes on Installation...4 Caution...4 1 Introduction...5 1.1 Features...5 1.2 Package Contents...5
More informationOmni-Directional 1D Barcode Scanner user manual
Omni-Directional 1D Barcode Scanner user manual Model 177597 MAN-177597-UM-1110-02 Installation & User s Manual Copyright 2009. This manual is copyrighted, with all rights reserved. Under the copyright
More informationCS-231. User Manual. Copyright ATEN International Co., Ltd. Manual Part No. PAPE G Printing Date: 11/2006
User Manual CS-231 Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the units and/or any devices that connect to them. This package
More informationCP MultiTouch Controller
CP450-010 MultiTouch Controller Welcome! We greatly appreciate your purchase of the CP450. We are sure you will find it reliable and simple to use. Superior performance for the right price, backed by solid
More informationUSER s GUIDE Toccare AIO Touch POS Systems
USER s GUIDE Toccare AIO Touch POS Systems 2011 JULY, Rev.B The information contained in this document is subject to change without notice. This document contains proprietary information that is protected
More informationInstallation Manual of DS-9600NI-H8 DS-9600NI-H8. Installation Manual UD.7L0202A1730B01
DS-9600NI-H8 Installation Manual UD.7L0202A1730B01 1 Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. Before you start, read the following
More informationWindows-Based Terminal. TK-3550 H.W. Manual
Windows-Based Terminal TK-3550 H.W. Manual Product Overview WBTs WBTs (Windows-based Terminals) are designed to connect to WTS (Windows Terminal Server) servers via RDP (Remote Desktop Protocol), or Windows
More informationUSB 3.0 Single/Dual Display Docking Station. User's Manual
USB 3.0 Single/Dual Display Docking Station User's Manual Table of contents Safety instructions...1 Copyright...1 Trademarks...1 Introduction...2 Features...2 Package contents...2 System requirements...3
More informationUSB-C Multiport Dock with Power Charging USER MANUAL UH3230
USB-C Multiport Dock with Power Charging USER MANUAL UH3230 EMC Information Federal Communication Commission Interference Statement: This equipment has been tested and found to comply with the limits for
More informationJentafon Wireless Loopset LPS-6 User Guide
Jentafon Wireless Loopset LPS-6 User Guide User Guide for Jentafon Wireless Loopset LPS-6 Jentafon Wireless Loopset LPS-6 is a Bluetooth headset for T-coil equipped hearing aid or cochlear implant users.
More informationIf anything is damaged or missing, contact your dealer.
User Manual CS-64A Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the unit and/or any devices that connect to it. This package
More informationTo force your device to restart, press and hold the power button until your device vibrates.
Quick Start CPN-W09 1 Your device at a glance Before you start, let's take a look at your new device. To power on your device, press and hold the power button until your device vibrates and the screen
More informationFCC COMPLICANCE STATEMENT
FCC COMPLICANCE STATEMENT For Users in the USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These rules are designed
More informationOperation Manual ZOOM CORPORATION Copying or reprinting this manual in part or in whole without permission is prohibited.
Operation Manual 2016 ZOOM CORPORATION Copying or reprinting this manual in part or in whole without permission is prohibited. Usage and Safety Precautions Usage and Safety Precautions Safety Precautions
More informationUSB Memory Adapter MAUSB-500 REFERENCE MANUAL
USB Memory Adapter MAUSB-500 REFERENCE MANUAL MAUSB-200 ReferenceManual Introduction The MAUSB-500 USB Memory Adapter (hereinafter referred to as the adapter ) is designed exclusively for reading and writing
More informationOptoma NuForce NuForce STA200 STA200 Stereo Amplifier Power Amplifier UserUser s Manual s Manual ALSTANZZ
NuForce Optoma NuForce STA200 STA200 Power Stereo Amplifier Amplifier User s User s Manual Manual ALSTANZZ FCC STATEMENTS This device has been tested and found to comply with the limits for a Class B digital
More informationUSER MANUAL. Elo Touch Solutions 2D Barcode Scanner Peripheral
USER MANUAL Elo Touch Solutions 2D Barcode Peripheral Copyright 2016 Elo Touch Solutions, Inc. All Rights Reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a
More informationUser Manual - KVM Rear Kit Version
dedicated KVM switch and rackmount screen technology User Manual - KVM Rear Kit Version for LCD Console Drawer PS/2 DB-15 KVM - 801 back Designed and manufactured by Austin Hughes 751 Legal Information
More informationOwner s Instruction Manual
Owner s Instruction Manual Advanced Healthcare Telephone Model 5150 Contents IMPORTANT SAFETY INSTRUCTIONS...3 BOX CONTENTS...4 FEATURES...4 ON/OFF SWITCH...4 DIAL BUTTONS...4 RECEIVER VOLUME CONTROL...4
More informationEVO-TM2A EVO-TM2B Touch Screen Monitor
User Manual Revision v1.3 Dec. 2010 EVO-TM2A EVO-TM2B Touch Screen Monitor Copyright 2010 August All Rights Reserved Manual Version 1.3 Part Number: The information contained in this document is subject
More informationCS-64U. User Manual
User Manual CS-64U Read this guide thoroughly and follow the installation and operation procedures carefully in order to prevent any damage to the units and/or any devices that connect to them. This package
More informationUSER MANUAL. VERSION V1.0 March Saturn Plus
USER MANUAL VERSION V1.0 March 2011 Saturn Plus Copyright 2011 March All Rights Reserved Manual Version 1.0 Part Number: 3LMKKPC70210 ii The information contained in this document is subject to change
More informationMP3 Speaker USER GUIDE
MP3 Speaker USER GUIDE Jazwares, Inc. 2012 CONTENTS Please read the instructions along with the Speaker carefully before you use it, so that you can operate it conveniently. WELCOME, Warnings & Safety
More informationInstallation & User s Manual Scantech-ID LIBRA L-7050 Multi-purpose Omni-directional scanner
Installation & User s Manual Scantech-ID LIBRA L-7050 Multi-purpose Omni-directional scanner Copyright 2010, Scantech-ID BV. This manual is copyrighted, with all rights reserved. Under the copyright laws,
More informationLP3 Multipurpose Laser Presenter
LP3 Multipurpose Laser Presenter User Manual Table of Contents 1. IMPORTANT SAFETY INSTRUCTIONS 2 2. PACKAGE CONTENTS 4 3. PART NAMES AND FUNCTIONS 4 4. SETUP AND INSTALLATION 5 5. BASIC OPERATION 5 6.
More informationDash Jr. User Manual Table of Contents
(/usermanuals) Dash Jr. User Manual Table of Contents Safety Information Safety Information Call Functions Contacts Messaging Opera Mini Browser Bluetooth & Wi Fi Camera Gallery Music Sound Recorder Alarm
More informationFCC Regulatory Information
DVW32C Advanced Wireless Voice Gateway - Safety and Installation Product Insert Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the
More informationSLIMLINE DASH CAM Audio & Video Recorder
SLIMLINE DASH CAM Audio & Video Recorder 1 EK142CAM INSTRUCTION MANUAL PLEASE READ ALL INSTRUCTIONS CAREFULLY AND RETAIN FOR FUTURE USE Getting Started Remove the Car Digital Video Recorder from the box.
More informationLinēa-pro 4 User Manual
Linēa-pro 4 User Manual iphone, ipod, ipod classic, ipod nano, ipod shuffle, and ipod touch are trademarks of Apple Inc., registered in the U.S. and other countries. ipad is a trademark of Apple Inc. www.ipcprint.com
More informationFlyTV MCE Installation Guide Animation Technologies Inc.
FlyTV MCE Installation Guide Animation Technologies Inc. www.lifeview.com Ver: 1.0 Copyright and Trademark Notice Copyright 2005 by Animation Technologies Inc. All rights reserved. Specifications and
More informationQuick Installation Guide
Quick Installation Guide Applicable Models: AS6004U Ver.3.0.0 (2017-4-13) Table of Contents Notices... 3 Safety Precautions... 4 1. Package Contents... 5 2. Optional Accessories... 6 3. Hardware Installation
More information