(Above 100km Distance) (Streetlight Pole) (Above 100km Distance) (Streetlight Pole)

Size: px

Start display at page:

Download "(Above 100km Distance) (Streetlight Pole) (Above 100km Distance) (Streetlight Pole)"

Ashlyn Jefferson
5 years ago
Views:

1 Part 9 Miscellaneous Drawing Register Number Description M1-1 SSN Network Device with LV Aerial Supply (ABC) Arrangement M1-2 SSN Network Device with LV Aerial Supply Arrangement M1-3 SSN Network Device with LV Aerial Supply (on HV Pole) Arrangement M1-4 SSN Network Device with Street Light Supply Arrangement M1-5 M1-6 M1-7 SSN Network Device with LV Kiosk (Type-1) Supply Arrangement (Above 100km Distance) (Power Pole) SSN Network Device with LV Kiosk (Type-1) Supply Arrangement (Above 100km Distance) (Streetlight Pole) SSN Network Device with LV Kiosk (Type-1) Supply Arrangement (Above 100km Distance) (Streetlight Pole) M3-1 Pole Top Switch or Isolator Ground Clearing Details M3-2 Expulsion-Type Dropout Fuse Ground Clearing Details M4-1 Third Party Electrical Attachment with LV Aerial Supply (ABC) Arrangement M4-2 Third Party Electrical Attachment with LV Aerial Supply Arrangement M4-3 Third Party Electrical Attachment with LV Aerial Supply (on HV Pole) Arrangement M4-4 Third Party Electrical Attachment with Street Light Supply Arrangement AS/NZS AS/NZS Clearances to ground and areas remote from building, railways and navigable waterways Spacing of conductors Horizon Power Corporation

2 WARNING THIS ANTENNA IS EARTHED TO ISOLATE FROM EARTH DISCONNECT ANTENNA CABLE AT CONTROL BOX. REMOVE ANTENNA IF WORK AREA IS OBSTRUCTED. RESTORE WHEN FINISHED R8-4 N PH 6mm 2C XLPE 20mm FLEXIBLE CONDUIT FOR MECHANICAL PROTECTION OF CABLES NOTE 2 (1PH-N) CB TOP OF BRACKET NOTE 1 L N L N A N E AERIAL SUPPLY SSN DEVICE NOTES: 1. USE 2 x 32mm BANDIT STRAPS FOR STEEL POLES, FOR EXISTING WOOD POLES USE 2 x M16 x 400mm BOLTS. 2. 1PH CB WITH "NEUTRAL FEED THROUGH POLE". SECURE CB TO POLE USING 20mm BANDIT STRAPS (STEEL) OR 2 x M12 BOLTS (WOOD) CIRCUIT BREAKER CUT-OUT DISTRIBUTION CONSTRUCTION STANDARDS OPERATIONS STRUCTURE - 9.5m SSN NETWORK DEVICE WITH LV AERIAL SUPPLY (ABC) ARRANGEMENT REVISION DATE B MAY 2014 DRAWING No. M1-1

5 EXISTING STREET LIGHT POLE OUTREACH JOINTING NOTE TOP OF BRACKET mm FLEXIBLE CONDUIT FOR MECHANICAL PROTECTION OF CABLES 2.5mm 2C+E NOTE 2 NOTE 5 A N E LV AC SUPPLY - SEE NOTE 3 (DOUBLE INSULATED CABLE) A N E EXISTING TO LUMINAIRE (DOUBLE INSULATED CABLE) A A N A N E NOTE 4 EXISTING LV SUPPLY STREET LIGHT CUT-OUT DETAIL NOTE 3 NOTES: 1. USE 2 x 32mm BANDIT STRAPS FOR STREET LIGHT POLES. 2. EXTEND THE LV AC SUPPLY FROM STREET LIGHTING POLE CUT-OUT TO ACCESS POINT/RELAY. 3. STREET LIGHT CUT-OUT WILL NEED TO COMPLY WITH NEW STANDARD. 4. ADD 5 AMP FUSE ON CUT-OUT FOR NEW CIRCUIT TO AP/RELAY. 5. DRILL A HOLE TO FIX 20mm CONDUIT GLAND. DISTRIBUTION CONSTRUCTION STANDARDS OPERATIONS STRUCTURE - STREET LIGHT POLE SSN NETWORK DEVICE WITH STREET LIGHT SUPPLY ARRANGEMENT REVISION DATE A DRAWING No. M1-4

6 WARNING THIS ANTENNA IS EARTHED TO ISOLATE FROM EARTH DISCONNECT ANTENNA CABLE AT CONTROL BOX. REMOVE ANTENNA IF WORK AREA IS OBSTRUCTED. RESTORE WHEN FINISHED EXISTING POWER POLE (LV OH BARE OR LV OH AB CABLE) R11-1 (AERIAL) N PH 2.5mm 2C+E CABLE 0.6/1kV CO-AXIAL CABLES 2500 NOTE 1 ANTENNAS (WAN & NAN) TOP OF BRACKET NOTE 3 ACCESS POINT/ RELAY A N E L N L N A N E BATT KIOSK A N E LV AC SUPPLY SEE NOTE 3 CIRCUIT BREAKER DETAIL MCB NOTE 2 (SEE DETAIL) ACCESS POINT SURGE PROTECTOR CO-AXIAL CABLES NOTES: 1. USE 2 x 32mm BANDIT STRAPS FOR STEEL POLES. FOR EXISTING WOOD POLES USE 2 x M16 x 400mm BOLTS. 2. 1PH CB WITH "NEUTRAL FEED THROUGH POLE" MTD IN KIOSK. 3. EXTEND THE LV AC SUPPLY FROM LV O/H BARE (OR LV O/H ABC) TO CB IN LV KIOSK AND THEN TO ACCESS POINT/RELAY. STRUCTURE - 9.5M POWER POLE REVISION DATE A DISTRIBUTION CONSTRUCTION STANDARDS OPERATIONS DRAWING No. SSN NETWORK DEVICE WITH LV KIOSK (TYPE-1) SUPPLY M1-5 ARRANGEMENT (ABOVE 100km DISTANCE)

7 EXISTING STREET LIGHT POLE OUTREACH JOINTING 1000 CO-AXIAL CABLES TOP OF BRACKET NOTE 1 ANTENNAS (WAN & NAN) ACCESS POINT/ RELAY L A N E N L N A N E A N E NOTE 4 LV AC SUPPLY SEE NOTE 3 CIRCUIT BREAKER DETAIL KIOSK BATT MCB NOTE 2 (SEE DETAIL) ACCESS POINT CO-AXIAL CABLES LV UG SUPPLY 2.5mm 2C+E CABLE 0.6/1kV SURGE PROTECTOR NOTES: 1. USE 2 x 32mm BAND-IT STRAPS FOR STREET LIGHT POLES. 2. 1PH CB WITH "NEUTRAL FEED THROUGH POLE". MTD IN KIOSK. 3. EXTEND THE LV AC FROM UG SUPPLY TO CB IN LV KIOSK AND THEN TO ACCESS POINT/RELAY. 4. USE BAND-IT STRAPS TO FIX CO-AX CABLE CONDUIT TO OUTSIDE OF POLE. DISTRIBUTION CONSTRUCTION STANDARDS OPERATIONS STRUCTURE - STREET LIGHT POLE SSN NETWORK DEVICE WITH LV KIOSK (TYPE-1) SUPPLY ARRANGEMENT (ABOVE 100kM DISTANCE) REVISION DATE A DRAWING No. M1-6

8 NEW STREET LIGHT POLE OUTREACH JOINTING 1000 CO-AXIAL CABLE TOP OF BRACKET ANTENNAS (WAN & NAN) NOTE 1 20mm FLEXIBLE CONDUIT FOR MECHANICAL PROTECTION OF CABLES NOTE 4 ACCESS POINT/ RELAY L A N E N L N A N E A N E LV AC SUPPLY SEE NOTE 3 CIRCUIT BREAKER DETAIL KIOSK BATT MCB NOTE 2 (SEE DETAIL) ACCESS POINT CO-AXIAL CABLES SURGE PROTECTOR NOTES: USE 2 x 32mm BANDIT STRAPS FOR STREET LIGHTING POLES. 1PH CB WITH "NEUTRAL FEED THROUGH POLE". MTD IN KIOSK. EXTEND THE LV AC SUPPLY FROM LV UG CABLE TO CB IN LV KIOSK AND THEN TO ACCESS POINT/RELAY. DRILL A HOLE TO FIX 20mm RUBBER SEAL. LV UG SUPPLY 2.5mm 2C+E CABLE 0.6/1kV DISTRIBUTION CONSTRUCTION STANDARDS OPERATIONS STRUCTURE - STREET LIGHT POLE SSN NETWORK DEVICE WITH LV KIOSK (TYPE-1) SUPPLY ARRANGEMENT (ABOVE 100kM DISTANCE) REVISION DATE A DRAWING No. M1-7

9 SIDE VIEW OF P.T.S 7m 7m A OVERHEAD VIEW 7m A OVERHEAD VIEW SHOWS THE FOOTPRINT TO BE CLEARED STRUCTURE GROUND CLEARING REVISION DATE B AUG 2015 DISTRIBUTION CONSTRUCTION STANDARDS OPERATIONS POLE TOP SWITCH OR ISOLATOR GROUND CLEARING DETAILS DRAWING No. M3-1

10 CASE 1: THREE PHASE POLE D.O.F. X = DISTANCE FROM POLE TO OUTSIDE PHASE + 3m A 8m OUTSIDE PHASE Y X CASE 2: SINGLE PHASE POLE Y = 3m FROM CENTRE OF POLE A 8m A A 3m X D.O.F. POLE POLE NOTE: 1. POINT A SHALL BE DETERMINED BY FOLLOWING A LINE FROM THE FUSE TO THE GROUND ALONG THE ANGLE OF THE FUSE. 2. FOR THREE-PHASE POLES, POINT A SHALL BE DETERMINED FROM CENTRE PHASE. STRUCTURE - GROUND REVISION DATE B AUG 2015 DISTRIBUTION CONSTRUCTION STANDARDS OPERATIONS EXPULSION TYPE DROPOUT FUSE DRAWING No. M3-2 GROUND CLEARING DETAILS

11 9/03/ :30:03 AM pw:\\oca-pw-701.ghdnet.internal:pwv8iss4prodhp\documents\projects\61\31024 Drawing Management System Transition\08_0 DRAFTING\8_3 DRAWINGS\Drawings\M4-1.dgn GIS mleroux

12 9/03/ :33:52 AM pw:\\oca-pw-701.ghdnet.internal:pwv8iss4prodhp\documents\projects\61\31024 Drawing Management System Transition\08_0 DRAFTING\8_3 DRAWINGS\Drawings\M4-2.dgn GIS mleroux

13 9/03/ :38:02 AM pw:\\oca-pw-701.ghdnet.internal:pwv8iss4prodhp\documents\projects\61\31024 Drawing Management System Transition\08_0 DRAFTING\8_3 DRAWINGS\Drawings\M4-3.dgn GIS mleroux

14 0/03/2017 4:21:29 PM pw:\\oca-pw-701.ghdnet.internal:pwv8iss4prodhp\documents\projects\61\32028 Misc. Minor Support Works\08_0 DRAFTING\8_3 DRAWINGS\M4-4 GIS mleroux

15 COPYRIGHT AS/NZS 7000:2016

16 COPYRIGHT AS/NZS 7000:2016

17 COPYRIGHT AS/NZS 7000:2016

18 COPYRIGHT AS/NZS 7000:2016

19 COPYRIGHT AS/NZS 7000:2016

20 COPYRIGHT AS/NZS 7000:2016

21 COPYRIGHT AS/NZS 7000:2016

22 COPYRIGHT AS/NZS 7000:2016

23 COPYRIGHT AS/NZS 7000:2016

24 COPYRIGHT AS/NZS 7000:2016

25 COPYRIGHT AS/NZS 7000:2016

26 COPYRIGHT AS/NZS 7000:2016

Common Departures Interconnecting Facilities Requirements

Common Departures Interconnecting Facilities Requirements Welcome to our e-rew Express. In our last issue, we discussed the common departures on metering installation requirements. This time, we would like to discuss the common departures on the customer low