USER MANUAL. Installation and Set Up. Model: IP8100C. Compact IP-PBX extensions 197 System.

Size: px

Start display at page:

Download "USER MANUAL. Installation and Set Up. Model: IP8100C. Compact IP-PBX extensions 197 System."

Anabel Skinner
5 years ago
Views:

1 USER MANUAL Installation and Set Up Model: IP8100C Compact IP-PBX extensions 197 System

2 Notification Notification is hereby given that Auto Telecom Company reserves the right to modify, change, update or revise this document from time to time as required without the prior obligation to notify any person, company or organization. Further, Auto Telecom Company makes no warranty or representation, either express or implied, with respect to merchantability, or fitness of its products for a particular purpose Auto Telecom Company This document or any parts thereof are not to be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or information storage and retrieval systems for any purpose whatsoever without the express written permission of Auto Telecom Company.

3 Table of Contents 1. Description System Programming Default IP Default NO Password Default system Set system password Into console programming Default setting of IP Trunk Default setting of IP extension Trunk ringing assignment Console Password System Technical password setting Technical password PSTN LINE Information IP-Trunk Information IP-extension Information Access Trunk Trunk Enable PR Software update software update software update Use a file to program VoIP File programming Modify Setting Upload Configured File System save and reboot... 12

4 1. Description IP8100C is a small IP-PBX system; it can register up to 197 IP-Extension with two IP-Trunks and one PSTN trunk. Easy to deploy and cost effective solution for community intercom, home environments or small office application. 1. RESET: Reset button 2. STOP: Shutdown button. Pressing 2 seconds for safely power down. 3. RS232: RS232 port 4. Normal/Default: Normal Operation / Clear Flash Memory 5. WAN1: to set IP address on mode 15 (LAN xxx) 6. WAN2: to set IP address on mode 15 (LAN xxx) 7. +5CVD IN: Power for IP FXO: FXO port 9. GPO1~GPO4: Dry connector for Relay1 ~ Relay4 (Normally Open 30VDC/1A) and refer setting on mode GPI1~GPI8: Sensors detection and refer setting on mode 06. GND with GPI1~GPI8 are sensor connectors.

2. System Programming Software version G-IP81-WF11cB1 and ip-8100c-003 (update via WinSock File Transfer Protocol WS_FTP) 2.1 Default IP Default IP is 10.10.10.5 Power on and wait 40 seconds to start; Use Google Chrome to log onto the IP8100 setup page: 2.

5 2. System Programming Software version G-IP81-WF11cB1 and ip-8100c-003 (update via WinSock File Transfer Protocol WS_FTP) 2.1 Default IP Default IP is Power on and wait 40 seconds to start; Use Google Chrome to log onto the IP8100 setup page: 2.2 Default NO Password Click System Programming, Default NO Password, click OK to proceed. 2.3 Default system Please click SYSTEM tab, then click Mode: 25 System Data Base Reset; Ensure pull down menu is showing 2: Reset All, then click SAVE button to auto configure extension number, name and password in Numbering Plan and Port/Station Number menu. After configuration complete, click on ImmediateBackup to save setting. 3

6 2.4 Set system password Click SYSTEM tab, then click PASSWORD (Mode: 13), see 1st row PROGRAM/FTP to set system password, then SAVE (Example password: 1234) If password lost, user can press hardware DEFAULT switch located on the back of IP8100C body to reset system. 2.5 Into console programming After enter the set up page by no password, click HOME, then SYSTEM PROGRAMMING, then click OK without enter password to enter Console Programming page to see simplified menu to set IP extension and IP Trunk 2.6 Default setting of IP Trunk Default setting of IP Trunk Account as below: 4

7 Setting Example: 2.7 Default setting of IP extension IP-Extension number, extension name and password can be changed in Port/Station Number 2.8 Trunk ringing assignment IP-Trunk and PSTN Trunk incoming call assignment setting 2.9 Console Password Console password can be set in the Console Page under SYSTEM, then PASSWORD 5

8 6

9 3. System 3.1 Technician password setting Click SYSTEM tab, then click PASSWORD (Mode: 13), see 1st row PROGRAM/FTP to set system password, then SAVE (Example password: 1234) 3.2 Technician password When user enters password (example: 1234), complete program setting menu will show on left column 3.3 PSTN LINE Information Click NUMBERING PLAN, then click PORT/STATION NUMBER (Mode: 21) to see default Port Number 171 with Number 801 for PSTN line 7

3.4 IP-Trunk Information Click NUMBERING PLAN, then

5 IP-extension Information Click NUMBERING PLAN, then

10 3.4 IP-Trunk Information Click NUMBERING PLAN, then click PORT/STATION NUMBER (Mode: 21) select CAB/SLOT: 1a to see two default IP-Trunk 802 and 803 information 3.5 IP-extension Information Click NUMBERING PLAN, then click PORT/STATION NUMBER (Mode: 21) select CAB/SLOT to show remain 197 IP extensions slots information 8

3.6 Access Trunk For outgoing calls setting, click Trunk, then click Mode 36: TRUNK GROUP ASSIGNMENT, 801 (PSTN), 802 & 803 (IP) For general dial out: dial 9 + number + # For assigned channel dial

11 3.6 Access Trunk For outgoing calls setting, click Trunk, then click Mode 36: TRUNK GROUP ASSIGNMENT, 801 (PSTN), 802 & 803 (IP) For general dial out: dial 9 + number + # For assigned channel dial out: dial number + # 3.7 Trunk Enable PR Click Trunk, then click Mode 35: TRUNK SPECIFICATION, please ensure all outgoing trunk 1. Type: 2=CO, Enable PR is selected, or user cannot answer ITU dial out calls 9

12 4. Software update 4.1 software update 1 IP8100c Software update via WS_FTP User ID is transtel (or hybrex) and default password is dddddddd 4.2 software update 2 After FTP connected, put new updates tgz file to /voip folder, it will auto update and restart system 10

5. Use a file to program VoIP. 5.1 File programming Using PC to setup IP-extension and ITU configuration (197 extension and 2 ITU) follow steps below: Use WS_FTP to download /bin/app/useraccount.

13 5. Use a file to program VoIP. 5.1 File programming Using PC to setup IP-extension and ITU configuration (197 extension and 2 ITU) follow steps below: Use WS_FTP to download /bin/app/useraccount.csv file to PC 5.2 Modify Setting Use Microsoft Excel to open UserAccount.CSV, administrator can perform batch setting with file (maximum 16 digits per cell; USER NUMBER use only numerical value) 11

CSV file back to the same folder to replace

14 5.3 Upload Configured File Upload UserAccount.CSV file back to the same folder to replace original file, /bin/app/useraccount.csv 5.4 System save and reboot Please log in setup page using browser IP: , select SYSTEM PROGRAMMING, and then MPU VOIP: T-2 S-197 to logon IP: :8080 Default User Name: admin Default Password:

15 After save system will automatically restart; after restart, use SYSTEM PROGRAMMING, NUMBERING PLAN, then PORT/STATION NUMBER (Mode: 21) to confirm change AUTO TELECOM COMPANY 13

Configuring the Grandstream UCM6202 for use with TopView Voice Notification Updated August 2018

Configuring the Grandstream UCM6202 for use with TopView Voice Notification Updated August 2018 Contents Introduction... 2 Voice Notification in TopView... 2 Options for using VOIP in TopView... 2 How