User Manual_T series T-OS01/T-IS01 T-PS01

Size: px

Start display at page:

Download "User Manual_T series T-OS01/T-IS01 T-PS01"

Amice Adams
5 years ago
Views:

1 User Manual_T series T-OS01/T-IS01 T-PS01

3 Catalog Overview... 1 Product Introduction... 2 Indoor Station Appearance...2 Indoor Station Size...4 Interface Instruction of Indoor Station...5 Indoor Station Specification...6 Outdoor Station Appearance...7 Outdoor Station Size Interface Instruction of Outdoor Station Outdoor Station Specification Power Supply Appearance Power Supply Size Interface Instruction of Power Supply Power Supply Specification System Connection Indoor Station-Basic Function & Settings Standby Interface Visitors intercom Monitor Call Out Message Indoor Station Setting Ring Setting Time setting Language setting Advanced Setup Outdoor Station Settings Default Setting Register Card Settings Unlock time setting ADD Setting Installation Where to install the outdoor station:... 31

4 How to install outdoor station: Where to install the indoor station How to install indoor station:... 34

5 Overview This product is a video intercom system based on two wire analog solution, the system uses two core wire to connect power supply, the outdoor station and indoor station. The functions are as below: Visual Intercom, Unlock; Monitor; 4 indoor station in 1 house; Intercom through the system s unit; TF card storage, screenshot and video record; Support KNX home automation 1

6 Product Introduction Indoor Station Appearance Model:T-IS01-W H Model:T-IS01-W L 2

7 Model:T-IS01-W H Model:T-IS01-W L 3

8 Indoor Station Size Model:T-IS01-W H Model:T-IS01-W L 4

9 Interface Instruction of Indoor Station

10 1: BUS1-A BUS1-B:Bus Port 1; BUS2-A BUS2-B:Bus Port 2; EXT-DC24V GND:Auxiliary Power Supply 24V; GND DoorBell:Interface of doorbell button; 2: 1:Setting on Master-Slave devic; 2:Impedance matching of video terminal; 3:Doorbell port; 4:485 Expansion interface; Note: 1When impedance matching the video terminal of the last indoor station device, please turn 2 on. 2The bus port A & B are used for connecting the indoor station. 3The master indoor station rings and screen wake up when it s called in, but slave device will only ring but not screen wake up. Indoor Station Specification Working Voltage:DC 24~32V Idle current: 10 ma (DC 32V) Working current: 200 ma (DC 32V) Screen:7 inches TFT Resolution:800 * 480 TF Card: 2~32G (Class 10 preferred) Dimension (L * W * D):220 * 140 * 24 mm 6

11 Outdoor Station Appearance Model:T-OS01-S-IC-01 Model: T-OS01-S-IC-02 Note: These models are for IC card only. Model:T-OS01-S-IC-04 7

12 Model:T-OS01-S-IC-01 Model:T-OS01-S-IC-02 8

13 Model:T-OS01-S-IC-04 Note: The Call button are related to different indoor station, please refer to the indoor station settings. 9

14 Outdoor Station Size Note:The above image is based on T-OS01-S-IC-02, the other models are the same size. 10

15 Interface Instruction of Outdoor Station : BUS-A BUS-B:Bus Port; NO COM NC :Normal on/off port; GS :Door status checking; DOOR SW:Unlock inside; GND :Public Area; Unlock timing settings, details in page 30 3: Outdoor Station ADD Settings, details in page 30 2: 11

16 Outdoor Station Specification Working voltage:dc 24~32V Idle current: 25 ma (DC32V) Working current: 150 ma (DC32V) Camera type:cmos PAL Camera pixel:30w Visual angle:90 Fill-in light:white light Size (L*W*D): 120 * 194 * 44.7 mm 12

17 Power Supply Appearance Model:T-PS01 13

18 Front Side: Back Size: 14

19 Power Supply Size 15

20 Interface Instruction of Power Supply BUS1 BUS2 BUS3:Bus Interface; L N :AC Port;L connect Live wire,n connect null wire, connect earth wire. Note: 1 The left red light will flash while the working in the bus line. 2 The middle green light will be on while working, and flash while receiving date signal. 3 The right green light is for back up use Power Supply Specification Working input voltage:ac 90V ~ 255V Output voltage:dc 30V Rated powert:30w Size (L*W*D): 144 * 90 * 64 mm 50/60Hz 16

21 System Connection Note: 1 The most devices of system: 2 outdoor station+16 indoor station. 2 The distance Ais the longest length between outdoor station 1 & 2, the distance B is the whole length between the power supply and the last indoor station. The wire as below: Wire (A+B) Length/m RVV 2*0.75mm² 110 Twisted-pair cable

Indoor Station-Basic Function & Settings Standby Interface 1 Monitor 3 Message touch icon to enter the touch icon to enter Message monitor interface,you can operate to make snap or video record.

22 Indoor Station-Basic Function & Settings Standby Interface 1 Monitor 3 Message touch icon to enter the touch icon to enter Message monitor interface,you can operate to make snap or video record. 2 Call touch icon to enter Call interface,you can make intercom among indoor stations in a unit or among different units; interface,you can view the snap, video; 4 Setting Present icon to enter Setting interface, you can set the tunes, languages, display and configuration. 18

23 Visitors intercom Ringing Procedure:Ringing Intercom Unlock End Incoming calls: 1 Visitors use the outdoor station to call the indoor station and the indoor station will ring. 2 After residents touch, the conversation begins. 3 During the conversation,the residents can touch to unlock the door,the call will end up automatically after 5s the door unlocks. 4 The resident touch or touch to end up the call. Note: 1 While calling, touch to keep sound coming from outdoor station; In other status, touch to mute the outdoor station and indoor station. 2 While screen wake up, touch calling, monitor),while the screen lock, touch to turn off the screen (except the interactive interface like to wake up the screen. 19

24 Setting: Setting 1 While the visitors calling, you can touch for setting operation. 2 Setting: Brightness, contrast and chroma Snap: 1 While the visitors calling, you can touch to make screenshot. 2 The snap pictures are stored in the call records. Video Record: 1 While the visitors calling, you can touch to record the video. 2 The videos are stored in the call records. Note: With TF card inserted, the storage is 40 video or 1000 pieces of photos. 20

25 Monitor Monitor & Unlock Procedure: Select the monitor Monitor Unlock End Monitor Visitors intercom Procedure:Monitor Intercom End While monitoring the outdoor station, the resident can touch to communicate 1 Touch or icon, select with visitors. the monitor device type. The outdoor station 1 (ADD 1) will be monitored acquiescently 2 Monitor the sight 3 To monitor the outdoor station, you can switch it by and. 4 While monitoring, the resident can touch to unlock for the visitors. 5 Touch to end monitoring. 21

26 Call Out On the main interface, touch to enter calling interface. Call out Units intercom Procedure:Call Ring Conversation End 1 Enter the room no and touch. 2 Hear ring back tone. 3 After the callee picks up, then start the conversation. 4 The resident can touch or to end up the intercom. Rooms intercom Procedure:Call Conversation End 1 Touch to start the intercom. 2 Hear ring back tone. 3 The indoor station of calleer rings. 4 The resident touch to end up the call. 22

Photos Touch to select the next photo, touch to select

27 Message Touch to enter message interface, check the snap/video Message Photos Touch for checking. Photos Touch to select the next photo, touch to select the previous one. Touch to delete photos,touch to delete all photos. 23

28 Video Touch to check the videos. Video Touch to select the next video, touch to select the previous one. Touch to delete vido,touch to delete all photos. Version Touch to check the version info,including the MCU and Address. Version 24

Ring Setting Indoor Station Setting On the main interface, touch ring setting: Ring setting Ringtone Of OS: to set the ringtone of outdoor station or indoor station; Ringtone Volume: to set the

29 Ring Setting Indoor Station Setting On the main interface, touch ring setting: Ring setting Ringtone Of OS: to set the ringtone of outdoor station or indoor station; Ringtone Volume: to set the ringtone volume of outdoor station or indoor station; Ringtone Of IS: to set the ringtone of indoor station Time setting On the main interface, touch time setting, to set the date and time. Time Setting 25

30 Language setting On the main interface, touch Language, to set the language. Language It s a must to set the language when the device is started at 1 st time. Advanced Setup On the main interface, touch Advanced setup,input the password to enter Note1: Original password: Password 26

31 Address Settings 高级设置界面 Touch the and set the address. Address Note: A. Address should be the number of 1 to 100 B. The address of indoor stations in one house should be the same. 27

32 Password Setting Touch the and set the password. Password Input the Old password and the new password to confirm Default Setting Touch and Yes to reset the device. Default 28

33 Outdoor Station Settings Default Setting Cut off the power of outdoor station, and restart it; The outdoor station ADD is 0, long touch any key for 3s, it will long ring after setting successfully. Register Card Settings Register Admin Card After the outdoor station reset, the first card to swipe will be the Admin card, it will long ring after setting successfully. Continuously Register User Card In standby mode, swipe the Admin card to enter the Register User Card Mode and it rings once. Within 15s time, user can register User Card. It will long ring and re-time again after success. When it s over 15s or fail to register, it will keep ringing and return to standby mode automatically; After registration, swipe the Admin card again to return to standby mode. Continuously Delete User Card In standby mode, swipe the Admin card twice to enter the Delete User Card Mode and it rings twice. Within 15s time, user can swipe to delete User Card. It will long ring and re-time again after success. When it s over 15s or fail to delete, it will keep ringing and return to standby mode automatically; After delete, swipe the Admin card again to return to standby mode. Continuously Register Admin Card In standby mode, swipe the Admin card 3 times to enter the Register Admin Card Mode and it rings 3 times. Within 15s time, user can register Admin Card. It will long ring and re-time again after success. When it s over 15s or fail to register, it will keep ringing and return to standby mode automatically; After registration, swipe the Admin card again to return to standby mode. Continuously Delete Admin Card In standby mode, swipe the Admin card 4 times to enter the Delete Admin Card Mode and it rings 4 times. Within 15s time, user can swipe to delete Admin Card. It will long ring and re-time again after success. When it s over 15s or fail to delete, it will keep ringing and return to standby mode automatically; After delete, swipe the Admin card again to return to standby mode. 29

34 Clear User Card In standby mode, swipe the Admin card 5 times to enter the Clear User Card Mode and it rings 10 times. Within 15s time, it will delete all user cards. It will long ring after success. When it fails to delete, it will keep ringing and return to standby mode automatically; After delete, swipe the Admin card again to return to standby mode. Note: Admin card+user card 200 张 Unlock time setting There s an adjustable potentiometer on the back side of outdoor station (2), for setting the unlocking time wihtin 180 ; Within 1s ~10s time,clockwise ratate to longthen, anticlockwise rotate to shorten. ADD Setting There s one 2 bits dialer (3),the method to set is as below: 1 2 ADD OFF OFF 0 ON OFF 1 OFF ON 2 ON ON 3 Note: It enters to setting mode when ADD is 0. 30

35 Installation Where to install the outdoor station: Suggesting height of installation:1.6m 31

36 How to install outdoor station: Step 1:Install the wall-in box, installation dimension (W/H/D) 100 * 180 *40mm Step 2:Put the outdoor station into the wall-in box, and fix it with screw. 32

37 Where to install the indoor station m Suggesting height of installation:1.5m 33

38 How to install indoor station: Step 1:Aim the screw hold of bracket with the holes of 86 box. Tighten the screw and fix the bracket Step 2:Connect the indoor station with wire, and aim the slot with the hanger of bracket. Then, move down the device a little bit. It s fixed when hearing Ka ta. 34

39 How to install the power supply 第一步 Step 1: Install the holding bracket and Tighten the screw and fix the bracket. Step 2:Aim the power supply box to bracket, and insert the fixing slot first, then spin the power supply and press till you hear the Ka ta. 35

CONTENTS. How to answer the call from the doorbell and release the door lock?...22

CONTENTS. How to answer the call from the doorbell and release the door lock?...22 CONTENTS FEATURES:... 2 SPECIFICATIONS:... 2 DSCRIPTIONS OF MONITOR: (Power voltage:ac 100-240V)... 3 DSCRIPTIONS OF MONITOR: (7/10.2 inch TFT Power voltage:dc 13.8V)... 4 DESCRIPTIONS OF MONITOR - REAR: