GUIDE SOFTWARE INSTALLATION USER MANUAL

Transcription

1 GUIDE SOFTWARE INSTALLATION USER MANUAL Tolteq Group, LLC Document #: Rev. A Software Revision:

2 INTELLECTUAL PROPERTY NOTICE If this manual is distributed with software, firmware, and hardware that includes an end-user agreement, this manual, as well as the software, firmware, or hardware described, is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by any such license, no part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, recording, or otherwise, without the prior written permission of Tolteq Group, LLC. Please note that the content in this manual is protected under copyright law, even if it is not distributed with software, firmware, or hardware that includes an end-user license agreement. The content of this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Tolteq Group, LLC. Tolteq Group, LLC assumes no responsibility or liability for any errors or inaccuracies that may appear in the informational content of this manual. Copyright 2012 Tolteq Group, LLC. All rights reserved. How to use this manual Navigation options Throughout this user manual, you will find references made to Figures, Chapters, Sections, and Topics. These references are also hyperlinks on which you can click and which lead you directly to the information you might seek. Because these hyperlinks appear in blue, you will be able to easily identify them. 2 Revision A

3 Navigation options you will find on every page The following navigation options will help you navigate through this manual effortlessly and fast: Click on the maroon arrows in the side margin of each page to go back or forth by one page. The Table of Contents Chapter Glossary Back displayed in the bottom margin of each page allow you to navigate to the different chapters, including the Table of Contents and Glossary. The Back option is used to jump back to the page on which you had previously clicked a link. This means, when you click a link to a certain page or figure and you then decide you want to go back to the page you last viewed, you can click on the Back option at the bottom of the page. Note The title page of this user manual lists the Tolteq internet address. You can click on it to open the Tolteq website. Conventions used in this manual The conventions that are used in this manual are described in the table below: Convention Emphasis Bold Blue Description Italic font is used to emphasize certain words or terms within the text. Bold font is used for software related functions and options, these include: Windows Panes Buttons File and directory names Menus and Menu bar options Tool bar options Fields Blue fond is used to indicate a hyperlink to any of the following: Another page Chapter Document Website Copyright

4 Revision history This section is intended to provide you with the revision history of your document. The Revision History table lists the following information and will be updated with each new release: Document Part # Revision Description Release Date A Initial release Revision A

5 Installation 1 GUIDE SOFTWARE INSTALLATION GUIDE software is part of Tolteq's GUIDE MWD Surface System, a field proven, complete wellsite solution. This software release is an update to existing version 4.8.0, and includes numerous enhancements and issue fixes. Note It is highly recommended to install the MWD Desktop and MWD Decoder individually via Ethernet connection. Installation Follow the steps below to update your MWD Desktop software, installed on laptop, and MWD Decoder software, installed on the RFD. It is highly recommended that you install the update for both the MWD Desktop and Decoder software individually. MWD Desktop Software Update 1. Ensure that your SSI cable is not connected. 2. Double click on the MWD Desktop icon, to open the MWD Desktop software. 3. Click on the Options menu, and select Update. 4. When you see the Options window: Copyright

6 MWD Desktop Software Update Figure 1: Options window 5. Uncheck the Update MWD Decoder before MWD Desktop (circled in Red). 6. Click OK. 7. Close the MWD Desktop program by clicking on the File menu, and select Exit All. 8. Connect your desktop or laptop computer to internet, and make sure that you have Internet access. 9. Ensure your SSI cable is not plugged in to the laptop. 10. Double click on the MWD Desktop icon, to open the MWD Desktop software. 11. Wait for about 60 seconds, and you should see the Software Update Available window pop up: Copyright

7 MWD Desktop Software Update 12. Click on the Update Now! button. 13. At the Internet Login window: Figure 2: Software Update Available window Figure 3: Internet Login window 14. Verify that your login info is correct and click the OK button. 15. Then you will see a few windows that will pop up and close by themselves. 16. Finally, the updated MWD Desktop will launch and display version Click OK. Copyright

8 MWD Decoder software update Figure 4: MWD Desktop MWD Decoder software update 1. Connect your Rig Floor Display (RFD) unit to the Ethernet cable, and make sure that you have Internet access. 2. MWD Decoder should start up automatically, if not double click on the MWD Decoder icon, to open the MWD Decoder software. 3. Wait for about 60 seconds, until the Software Update Available window pops up: Copyright

9 MWD Decoder software update 4. Click on the Update Now! button. 5. You will see an Internet Login window: Figure 5: Software Update Available window Figure 6: Internet Login window 6. Verify that your login info is correct and click the OK button. 7. Then you will see a few windows will pop up and close by themselves. 8. Finally, the updated MWD Desktop will launch and display version Copyright

10 Troubleshooting Troubleshooting Copyright

11 Troubleshooting Copyright