páêçå~=aéåí~ä=`^al`^j=póëíéã áåbçë=_äìé

Transcription

1 kéï=~ë=çñw= MTKOMNN páêçå~=aéåí~ä=`^al`^j=póëíéã áåbçë=_äìé lééê~íáåö=fåëíêìåíáçåë båöäáëü=erpf Operating Instructions

2 Sirona Dental Systems GmbH Table of contents 1 Dear Customer, General information Structure of the document Identification of danger levels Formats and symbols used Legend Warranty Safety Basic safety information Prerequisites Connecting the unit Connection to the CEREC 3 acquisition unit Connection to the CEREC AC acquisition unit Connection of external equipment Maintenance and repair Changes to the product Accessories In case of damage Intended use Further use of Sirona Dental CAD/CAM System Certification Technical description Design and function System components Components of the ineos Blue Accessories (included in the scope of supply) Calibration parts (included in scope of supply) D acquisition system XYZ axis alignment Technical data System requirements Transport to the installation site D

3 Sirona Dental Systems GmbH 5.1 Transport and unpacking Installation site Initial installation of the software Installation of the user software and initial start-up Connecting the unit to the PC Switching the unit on and starting the software Selecting the 3D acquisition system Adding ineos Blue to the device configuration Connecting the unit Connecting the ineos Blue to the PC Connecting the ineos Blue to the power supply Connecting the rotation mouse Connecting the foot switch Controls and displays Controls on the ineos Blue Ready LED Switching the system on Calibration General information on calibration Calibrating the 3D camera system Calibrating the XYZ axis alignment Performing 3D acquisition General Scan models Focusing the image Overlap area during acquisition Deleting images Operating the foot switch Raster scans Preparing the model Taking a scan D

4 Sirona Dental Systems GmbH 11.3 Free scans Preparing the model Taking a scan Performing detail scans Rotational scans Preparing the model Taking a scan Acquiring impressions Examples Scan of a 3-unit bridge Acquiring a preparation Rotational scans Acquiring an antagonist Bite registration Buccal scan Terminating acquisition Acquisition of a crown cap Exposure of an inlay Acquiring a preparation Considering the antagonist Terminating acquisition Cleaning and care Care of the 3D camera system Cleaning the outer surface Protection against medicaments D

5 Sirona Dental Systems GmbH 1 Dear Customer, 1 Dear Customer, Dear Customer, Thank you for purchasing your ineos Blue from Sirona. Improper use and handling can create hazards and cause damage. Please read and follow these operating instructions carefully and always keep them within easy reach. To prevent personal injury or material damage, it is important to observe all safety information. To safeguard your warranty claims, please complete the attached Installation Report / Warranty Passport when the system is handed over and send it to the indicated fax number. Your ineos Blue Team D

6 2 General information Sirona Dental Systems GmbH 2.1 Structure of the document 2 General information General information CAUTION Be sure to observe all warnings! Please observe the warning and safety information provided to prevent personal injury and material damage. Any such information is highlighted by a signal word, i.e. DANGER, WARNING, CAUTION or NOTICE. Please read this document completely and follow the instructions exactly. You should always keep it within reach. Original language of the present document: German. 2.1 Structure of the document Structure of the document Identification of danger levels Identification of danger levels To prevent personal injury and material damage, please observe the warning and safety information provided in this document. Such information is highlighted as follows: DANGER An imminent danger that could result in serious bodily injury or death. WARNING A possibly dangerous situation that could result in serious bodily injury or death. CAUTION A possibly dangerous situation that could result in slight bodily injury. NOTICE A possibly harmful situation which could lead to damage of the product or an object in its environment. IMPORTANT Application instructions and other important information. Tip: Information on making work easier. 6 D

7 Sirona Dental Systems GmbH 2 General information Formats and symbols used Formats and symbols used The symbols and character formats used in the present manual have the following meaning: Prerequisite 1. First action step 2. Second action step or Alternative action Result See "Formats and symbols used [ 7] 2.2 Legend Requests you to do something. Identifies a reference to another text passage and specifies its page number. List Identifies a list. "Command/menu item" Identifies commands, menu items or quotations. 20XX Legend Year of manufacture 2.3 Warranty Warranty To safeguard your warranty claims, please complete the attached Installation Report / Warranty Passport when the unit is handed over. Then fax it to the specified fax no. D

8 3 Safety Sirona Dental Systems GmbH 3.1 Basic safety information 3 Safety Safety 3.1 Basic safety information Basic safety information Prerequisites Prerequisites NOTICE Important information on the building installation The building installation must be performed by a qualified expert in compliance with the national regulations. DIN VDE applies in Germany. NOTICE Restrictions regarding installation site The system is not intended for operation in areas subject to explosion hazards. NOTICE Do not damage the unit! The unit can be damaged if opened improperly. It is expressly prohibited to open the unit with tools! Connecting the unit Connecting Description the unit Perform connection by following the directions given in the present operating instructions Connection to the CEREC 3 acquisition unit Connection Warning: ineos to the connected CEREC 3 to acquisition CEREC 3 acquisition unit unit WARNING No acquisitions in the patient's mouth As long as an ineos Blue is connected to a CEREC 3 acquisition unit, no acquisitions may be made in the patient's mouth using the connected CEREC 3D camera. 8 D

9 Sirona Dental Systems GmbH 3 Safety Connection to the CEREC AC acquisition unit Patient environment Connection to the CEREC AC acquisition unit 1500mm mm mm mm mm mm mm mm mm mm mm 59 Within the patient environment (A), direct contact is only permissible with devices or system parts that are approved for use in the patient environment (A). This applies to all possible patient positions (B) during the examination or treatment. ineos outside of patient environment WARNING No acquisitions in the patient's mouth within the patient environment As long as an ineos Blue is connected to a CEREC AC acquisition unit, no acquisitions may be made in the patient's mouth using the connected CEREC Bluecam if the ineos Blue is located outside of the patient environment. D

10 3 Safety Sirona Dental Systems GmbH 3.1 Basic safety information Connection of external equipment Connection of external equipment If any equipment not approved by Sirona is connected, it must comply with the applicable standards: EN for information technology equipment, and EN for laboratory equipment Maintenance and repair Maintenance and repair As manufacturers of dental instruments and laboratory equipment, we can assume responsibility for the safety properties of the unit only if the following points are observed: The Maintenance and repair of this unit may be performed only by Sirona or by agencies authorized by Sirona. Components which have failed and influence the safety of the unit must be replaced with original (OEM) spare parts. Please request a certificate whenever you have such work performed. It should include: The type and scope of work. Any changes made in the rated parameters or working range. Date, name of company and signature Changes to the product Changes to the product Modifications to this unit which may affect the safety of the operator, patients or third parties are prohibited by law! Accessories Accessories In order to ensure product safety, this product may be operated only with original Sirona accessories or third-party accessories expressly approved by Sirona. The user assumes the risk of using non-approved accessories In case of damage In case of damage In case of noticeable malfunctions or damage, stop using the instrument immediately and notify your dental depot or the manufacturer. 10 D

11 Sirona Dental Systems GmbH 3 Safety 3.2 Intended use Intended Indications use for use The Sirona Dental CAD/CAM System is intended for use in partially or fully edentulous mandibles and maxillae in support of single or multipleunit cement retained restorations. The system consists of three major parts: TiBase, incoris mesostructure, and CAD/CAM software. Specifically, the incoris mesostructure and TiBase components make up a two-piece abutment which is used in conjunction with endosseous dental implants to restore the function and aesthetics in the oral cavity. The incoris mesostructure may also be used in conjunction with the Camlog Titanium base CAD/CAM (types K2244.xxxx) (K083496) in the Camlog Implant System. The CAD/CAM software is intended to design and fabricate the incoris mesostructure. The incoris mesostructure and TiBase two-piece abutment is compatible with the following implants systems: Nobel Biocare Replace (K020646) Nobel Biocare Branemark (K022562) Friadent Xive (K013867) Biomet 3i Osseotite (K980549) Astra Tech Osseospeed (K091239) Zimmer Tapered Screw-Vent (K061410) Straumann SynOcta (K061176) Note for use in the USA Note for use in the USA CAUTION: According to US Federal Law, this product may be sold only to or by instruction of physicians, dentists, or licensed professionals. 3.3 Further use of Sirona Dental CAD/CAM System Further use of Sirona Dental CAD/CAM System The Sirona Dental CAD/CAM System is also an optical impression system for computer assisted design and manufacturing (CAD/CAM) according to 21 CFR The system records the topographical characteristics of teeth, dental impressions, or stone models for use in the computer-assisted design and manufacturing of dental restorative prosthetic devices. Such devices are exempt from the premarket notification procedures. D

12 3 Safety Sirona Dental Systems GmbH 3.4 Certification 3.4 Certification Certification CE mark This product bears the CE mark in accordance with the provisions of directives 2006/95/EC (Low Voltage Directive) and 2004/108/EC (EMC Directive). CAUTION CE mark for connected products Further products which are connected to this unit must also bear the CE mark. These products must be tested according to the applicable standards. Examples EN CAN/CSA Examples of CE mark for connected products: EN 60950: A1: A2: A3: A4:1997 based on IEC CAN/CSA-C22.2 No inlab+eos GOST mark GOST mark CSA mark CSA mark VDE mark C US VDE mark 12 D

13 Sirona Dental Systems GmbH 4 Technical description 4 Technical description Technical description 4.1 Design and function Design and function The ineos Blue is designed as a desktop unit and consists of several components (see Chapter "System components" [ 13]). It is powered from the standard local power network via an external power supply unit. The unit is connected to a PC via a USB port. The PC must fulfill the minimum requirements (see Chapter on "System requirements" [ 17]). The PC serves both for controlling ineos Blue and for displaying the captured images by means of the user software. C A D B A B C D External power supply unit Supply board Rotation mouse 3D acquisition system 4.2 System components System components "ineos Blue" consists of a base plate and a vertical unit. In addition, different accessories as well as the required calibration kits are included in the scope of supply of the system. D

14 4 Technical description Sirona Dental Systems GmbH 4.2 System components Components of the ineos Blue Components of the ineos Blue Vertical unit and front side of base plate A Vertical unit E Base plate B Rotary knobs for height F Ready LED (blue) adjustment C Height adjustment unit G Shifting plate with 3D camera system D Cone with glass H Start button protection cover I Rotation mouse 14 D

15 Sirona Dental Systems GmbH 4 Technical description Rear side of base plate A B C D Main switch Supply voltage input USB port Rotation mouse Accessories (included in the scope of supply) Accessories (included in the scope of supply) C D E A B F A B C D E F Model holder (with ball-and-socket joint) Sliding block Clamps Model pot 31 (3x) Model pot 52 (2x) Plate D

16 4 Technical description Sirona Dental Systems GmbH 4.2 System components Foot control Calibration parts (included in scope of supply) Calibration parts (included in scope of supply) D acquisition system 3D acquisition system Calibration part for calibrating the 3D acquisition system. A A Calibration part XYZ axis alignment XYZ axis alignment Calibration parts for calibrating the XYZ axis alignment A B A B Calibration plate Spacer 16 D

17 Sirona Dental Systems GmbH 4 Technical description 4.3 Technical data Model designation Technical data ineos Blue Power connection via power supply unit: INPUT: VAC / 47-63Hz / 1.0 A max. permissible line voltage fluctuations: ± 10% of nominal voltage Overvoltage category II OUTPUT: +12VDC / 2.08A / 25W max. Power consumption 15 W Ambient conditions For indoor use Pollution degree 2 Temperature: 10 C 35 C (50 F ~ 95 F) Relative humidity: 30% 75% Barometric pressure: 700hPa 1060hPa Transport and storage conditions Temperature: -40 C +70 C (-40 F ~ 158 F) Relative humidity: 10% 95% Barometric pressure: 500hPa 1060hPa Protection class Class I device Degree of protection against ingress of water Ordinary equipment (not protected) Mode of operation Continuous operation with intermittent loading corresponding to the laboratory mode of working. Tabletop unit Tests/approvals This device complies with the requirements of EN : System requirements System requirements An inlab PC 64bit is required to run this software. The hardware version must be PC Hardware L or higher. D

18 5 Transport to the installation site Sirona Dental Systems GmbH 5.1 Transport and unpacking 5 Transport to the installation site Transport to the installation site 5.1 Transport and unpacking Transport and unpacking All Sirona products are carefully checked prior to shipment. Please perform an incoming inspection immediately after delivery. 1. Check the delivery note to ensure that the consignment is complete. 2. Check whether the product shows any visible signs of damage. NOTICE Damage during transport If the product was damaged during transport, please contact your carrying agent. If return shipment is required, please use the original packaging for shipment. 5.2 Installation site Installation site The unit is designed for desktop use and requires a level footprint of approx. 35 x 45 cm for installation. Make sure that suitable operating conditions are given (see section on Technical data [ 17]). NOTICE Install ineos Blue in a protected area 3D image acquisition may be adversely affected by bright light. Set the ineos Blue up so that it is not located directly in the beam path of an extreme light source and not exposed to direct sunlight. 18 D

19 Sirona Dental Systems GmbH 6 Initial installation of the software 6 Initial installation of the software Initial installation of the software NOTICE Initial installation without ineos Blue Perform the initial installation of the software without connecting ineos Blue. 6.1 Installation of the user software and initial start-up of the Installation 1. user software and initial start-up Start your PC. 2. Insert the DVD into the DVD drive of your PC. NOTICE Installation does not start The installation will start automatically. If it does not start, the CD autorun feature is disabled on your PC. In this case start the setup.exe file on the CD-ROM by double-clicking it. The installation wizard opens. 3. Click the "next" button. 4. Read the license agreement. 5. Confirm your acceptance by clicking the "Yes" button. 6. Click "Standard Installation". NOTICE User-defined installation The user-defined installation option is recommended only for experienced users. The standard installation is then executed. 7. Follow the instructions of the installation wizard to complete the installation. 8. Restart the system. The software and drivers are installed. 6.2 Connecting the unit to the PC Connecting the unit to the PC Connect the ineos Blue to the PC (see also section Connecting the unit [ 22]). D

20 6 Initial installation of the software Sirona Dental Systems GmbH 6.3 Switching the unit on and starting the software 6.3 Switching the unit on and starting the software Switching Let unit dry the off unit after on storage and starting the software NOTICE Do not put the unit into operation at low temperatures! If you move the unit to the operating site from a cold environment, condensation may form and result in a short circuit. Install the unit at room temperature. Wait until the unit has reached room temperature and is absolutely dry. The unit is dry and can be put into operation. 1. Switch the unit on at the main switch. 2. Start the software at the PC via the Windows start menu. 6.4 Selecting the 3D acquisition system Selecting the 3D acquisition system 1. Click "Settings"/"Configuration"/"Acquisition system" in the user software. The menu for selection of the 3D acquisition system opens. 2. Select "ineos". 3. Click the "OK" button. 20 D

21 Sirona Dental Systems GmbH 6 Initial installation of the software 6.5 Adding ineos Blue to the device configuration Adding Calibrating ineos the Blue system to the device configuration 1. Click "Settings"/"Configuration"/"Devices..." in the user software. The "Configure Devices" dialog box opens. 2. Click the "Add automatically" button and enter a name for this device ("ineos Blue" is suggested). NOTICE ineos Blue is not displayed If ineos Blue does not appear in the "Configure Devices" dialog, check the configuration of the interface (see the section entitled Checking and configuring the serial interface ). 3. Click the "Add Device" button. The installation is now completed. Calibrating the system NOTICE Calibrating the system After installing the ineos Blue, you must calibrate the system (see the chapter entitled "Calibration" [ 27]). D

22 7 Connecting the unit Sirona Dental Systems GmbH 7.1 Connecting the ineos Blue to the PC 7 Connecting the unit Connecting the unit CAUTION Switching the PC off Switch the PC off before connecting the ineos Blue. 7.1 Connecting the ineos Blue to the PC Connecting the ineos Blue to the PC A B C Socket (USB port) of ineos Blue Interface cable Socket (USB port) on the rear of the PC (labeled "ineos Blue") Connect the socket (USB port) of the ineos Blue (A) to the socket (USB port) of your PC (C) via the interface cable included in the scope of supply (B). 7.2 Connecting the ineos Blue to the power supply Connecting the ineos Blue to the power supply A Socket for power supply Connect the socket (A) of the ineos Blue to the power supply via the power supply unit included in the scope of supply. 22 D

23 Sirona Dental Systems GmbH 7 Connecting the unit NOTICE Use a grounded power outlet The power supply unit must be connected to a grounded power outlet. 7.3 Connecting the rotation mouse Connecting the rotation mouse A B Socket of the ineos Blue Rotation mouse Plug the connector of the rotation mouse (B) into the matching socket (A) on the ineos Blue. 7.4 Connecting the foot switch Connecting the foot switch Plug the connector of the foot switch into the matching socket (USB port) of your PC. D

24 8 Controls and displays Sirona Dental Systems GmbH 8.1 Controls on the ineos Blue 8 Controls and displays Controls and displays 8.1 Controls on the ineos Blue Controls on the ineos Blue The following controls are available on the ineos Blue: A B C D Rotary knobs for height adjustment (focusing) of the lens on the vertical unit Start button Main switch Rotation mouse 24 D

25 Sirona Dental Systems GmbH 8 Controls and displays 8.2 Ready LED Ready LED The blue Ready LED indicates the operating status of the unit: A LED not lit: Unit is switched off B LED flashes: Unit is switched on and ready for operation D

26 9 Switching the system on Sirona Dental Systems GmbH 9 Switching the system on Switching Let unit dry the off system after storage on NOTICE Do not put the unit into operation at low temperatures! If you move the unit to the operating site from a cold environment, condensation may form and result in a short circuit. Install the unit at room temperature. Wait until the unit has reached room temperature and is absolutely dry. The unit is dry and can be put into operation. Switching the system on Switching the ineos Blue on 1. Switch on the PC. 2. Switch the ineos Blue on at the main switch. Starting the software Start the software at the PC via the Windows start menu. 26 D

27 Sirona Dental Systems GmbH 10 Calibration 10 Calibration Calibration 10.1 General information on calibration General information on calibration The ineos Blue has two components that must be calibrated: 3D camera system XYZ axis alignment NOTICE Calibrate prior to initial startup Prior to initial startup of the ineos Blue, you must perform a full calibration. No further calibrations are usually required afterwards. If you remove the shifting plate, the X-Y-Z alignment must be recalibrated after reassembling the unit. Various calibration standards and parts are required for calibration (see Chapter on "Calibration parts" [ 16]). They are included in the scope of supply of the ineos Blue. Recalibrate your ineos Blue following transport (shaking stress), after storage in unheated or un-air-conditioned rooms (temperature differences exceeding 30 C), with temperature differences of over 15 C between the last calibration and operation Calibrating the 3D camera system Calibrating the 3D camera system Preparing the ineos Blue NOTICE Do not damage the calibration parts Proceed carefully when attaching or removing the calibration part in order to ensure that it is not damaged or contaminated. The PC and the ineos Blue are switched on. The inlab software is started 1. Click "Settings"/"Calibration"/"inEos"/"Camera system". D

28 10 Calibration Sirona Dental Systems GmbH 10.3 Calibrating the XYZ axis alignment The window for calibrating the 3D camera system opens. You will be prompted to attach the calibration part. 2. Fasten the calibration part to the left side of the cone with the clip. 3. Tilt the calibration part via the cone. 4. Slide the calibration part upward up to the stop. 5. Confirm the message box with the "OK" button. The calibration is performed. A message appears stating that the unit has been successfully calibrated. 6. Confirm the message box with the "OK" button. 7. Remove the calibration part. Note: After each additional calibration of the camera system, you also must calibrate the X-Y-Z axis alignment Calibrating the XYZ axis alignment Calibrating the XYZ axis alignment 1. Click "Settings"/"Calibration"/"inEos"/"XYZ alignment". Tip: The following dialog boxes will guide you through the calibration procedure and provide all relevant information. The calibration window and a message box open. 2. Check to make sure that the calibration parts are not damaged and click the "OK" button. Step 1 Step 1 1. Place the calibration plate in position 1. Note the position of the beveled corner. The grid balls must be seated as shown in the illustration. The right half of the cylinder is located in the image field. 28 D

29 Sirona Dental Systems GmbH 10 Calibration 2. Adjust the spacer as shown in the illustration between the calibration plate and the cone and move the vertical unit into the bottom position. Remove the spacer. NOTICE Do not change this position This position must not be further changed until step Click the "Acquire" button. The scan starts. Step 2 Step 2 1. Position the calibration plate in position 2. Note the position of the beveled corner. The grid balls must be seated as shown in the illustration. The left half of the cylinder is located in the image field. 2. Click the "Acquire" button. The scan starts. Step 3 Step 3 1. Rotate the calibration plate counterclockwise 90 and position it in position 3. Align the calibration plate so that the grid balls are seated as shown in the illustration. The upper half of the cylinder is located in the image field. 2. Click the "Acquire" button. The scan starts. D

30 10 Calibration Sirona Dental Systems GmbH 10.3 Calibrating the XYZ axis alignment Step 4 Step 4 1. Position the calibration plate in position 4. Note the position of the beveled corner. The grid balls must be seated as shown in the illustration. The bottom half of the cylinder is located in the image field. 2. Click the "Acquire" button. The scan starts. Step 5 Step 5 1. Screw in the calibration plate 90 clockwise and place it in position 1. Align the calibration plate in such a way that the grid balls are seated as shown in the illustration. The cylinder is positioned horizontal. The right half of the cylinder is located in the image field. 2. Move the vertical unit upward (approx. 7mm) until the spacer fits between the calibration plate and the cone as shown in the illustration. Remove the spacer. 3. Click the "Acquire" button. The scan starts. 30 D

31 Sirona Dental Systems GmbH 10 Calibration Step 6 Step 6 1. Turn the calibration plate counterclockwise 90 and place it in position 3. Note the position of the beveled corner. The grid balls must be seated as shown in the illustration. The bottom half of the cylinder is located in the image field. 2. Click the "Acquire" button. The scan starts. The automatic calibration of the XYZ axis alignment is now completed. 3. Confirm the successful calibration in the inlab software with the "OK" button. 4. Remove the calibration plate from the shifting plate. D

32 11 Performing 3D acquisition Sirona Dental Systems GmbH 11.1 General 11 Performing 3D acquisition Performing 3D acquisition 11.1 General General Acquisition methods You have three modes for executing scans with ineos Blue: Grid acquisition For large scans with 9 or more units Long, untoothed areas Free scan For scans with up to and including 8 units For additional scans at different angles Rotational scan For the surveying of single tooth stumps For single restorations without consideration of the proximal contacts or the antagonist You can execute several scan modes in sequence. You can omit a scan mode if, for example, it is not suitable for your model Scan models Scan Materials models You can scan all materials that correspond to the following criteria: Non-reflecting Nontransparent No transparent parts Not highly absorbent (e.g. heavily colored plasters) Unscannable materials generate artifacts in the image. Tip: When using plasters that do not meet the above criteria, you must powder the affected areas. Otherwise the measuring accuracy will be impaired considerably. The following are suitable for this purpose: CEREC Optispray (REF ) For scanning with ineos Blue, we recommend using CEREC Stone BC plaster (REF ). Saw-cut etc. When preparing saw-cut models, be careful not to mill off the single stump segments. Place the model next to the stumps so that the scanner can properly capture these areas. Create only a slight fluting below the preparation margin. 32 D

33 Sirona Dental Systems GmbH 11 Performing 3D acquisition Focusing the image Focusing the image Turn the rotary buttons for height adjustment. The sharpness adjustment changes. The image is then sharpened if the relevant areas are not red. Left: Scan clear; Right: Scan unclear Object unclear If the object is unclear while the image is being acquired, the error message "Object out of focus! Move camera down!" or "Object out of focus! Move camera up!" appears. Sharpen the image and take a new scan Overlap area during acquisition Overlap area during acquisition If images are acquired via free scans, each image must overlap with the previous image. This overlap area must comprise roughly half of the image. Overlapping insufficient If the overlap with the previous scans is not sufficient, the software cannot assign the image. The error message "No matching data found" appears. Select a section that has a larger overlap with previously acquired images or reduce the tilt Deleting images Deleting images Deleting images You can delete completed scans by right-clicking on the active scan icon (e.g. "Preparation"). Each further click deletes the last scan. D

34 11 Performing 3D acquisition Sirona Dental Systems GmbH 11.2 Raster scans Operating the foot switch Operating the foot switch You can use the foot switch instead of the start button of the ineos Blue. Link to ineos Blue To do this, connect the foot switch as described in the chapter entitled "Connecting the foot switch" [ 23] Raster scans Raster scans Preparing the model Preparing the model 1. Secure the model to the model holder included. The labial side faces the fixing screw. 2. Release the ball and socket joint. 3. Align the model: The model is horizontal and the front teeth stand parallel to a triangle side. 4. Remove the sliding block from the model holder Taking a scan Taking a scan NOTICE Do not damage the shifting plate Do not apply any pressure to the model when it is located on the shifting plate. Doing so could damage the shifting plate. Tip: Do not change the position of the ball-and-socket joint during acquisition. 34 D

35 Sirona Dental Systems GmbH 11 Performing 3D acquisition 1. Place the model holder on the shifting plate. The small balls must lodge in the longitudinal and transverse grooves. The tip of the model holder plate and the oral side of the model face the column of the ineos Blue. 2. Click the icon for grid scans. A section of the model appears in the the live image. 3. Slide the model until you can begin scan acquisition on a distal side. 4. Focus the image with the rotary knobs for height adjustment; see Focusing the image [ 33]. Do not touch the rotary knobs during the image acquisition process. 5. Single-click the Start button of the ineos Blue. The image is acquired. 6. Add additional scans from adjacent areas: Move the model in the desired direction by one stop position and repeat steps 4 to 5. If you do not require any further grid scans, you can change to the next acquisition mode; see Free scans [ 35] or Rotational scans [ 38]. Tip: If a bite registration is to be acquired, additional mesial and distal areas also must be scanned. These areas must not be concealed by the bite registration Free scans Free scans You can also take detail scans from different angles in this mode. You can use detail scans for example to detect undercuts which were not detected by the overview scans. D

36 11 Performing 3D acquisition Sirona Dental Systems GmbH 11.3 Free scans Preparing the model Preparing the model 1. Press the triangular glide foot on to the bottom of the model holder until the glide foot clicks into place. The model holder can be moved into any position across the shifting plate. 2. Secure the model to the model holder included. The labial side faces the fixing screw. 3. Release the ball and socket joint. 4. Align the model: The model is horizontal and the front teeth stand parallel to a triangle side Taking a scan Taking a scan The Free Scan mode offers a variety of options for image acquisition. Acquisition with the Start button Double-click the Start button Single-click the Start button. A single exposure will be acquired. The crosshairs turn blue. The system will automatically acquire new images after you move the model or reset the image focus. If you want to interrupt the automatic scan, single-click the Start button of the ineos Blue. The crosshairs turn green. Use the Start button to acquire additional exposures. Tip: When taking detail scans, interrupt the automatic scan to continue at a different model location. This location must overlap roughly one half of the image previously scanned. 36 D

37 Sirona Dental Systems GmbH 11 Performing 3D acquisition Acquisition with the foot switch Actuate the foot switch once Press and hold down the foot switch A single exposure will be acquired. The model must be motionless and set in focus. The crosshairs turn blue. The system will automatically acquire new images after you move the model or reset the image focus. To interrupt the automatic scan, simply let go of the foot switch. The crosshairs turn green. You can acquire additional exposures by reactivating the foot switch. Tip: When taking detail scans, interrupt the automatic scan to continue at a different model location. This location must overlap roughly one half of the image previously scanned. Taking the scan 1. Click the Free Scan icon. A section of the model appears in the the live image. 2. Slide the model until you can begin scan acquisition on a distal side. 3. Focus the image with the rotary knobs for height adjustment; see Focusing the image [ 33]. 4. Single-click the Start button of the ineos Blue. The first scan is taken and the crosshairs are displayed blue. 5. Add additional scans from adjacent areas: Move the model freely on the table until you have reached the next acquisition position. As soon as the model stops moving, the camera is automatically released. You can turn the model on the shifting plate by up to 30. Tip:The new image must overlap approximately one half of the previous image. If necessary, you can turn the model by Repeat step 5 until all of the required scans have been taken. If you do not require any further free scans (including detail scans), you can change to the next acquisition mode; see Rotational scans [ 38] Performing detail scans Performing detail scans You can acquire detail scans at any time during the free scan. 1. Tilt the model no more than 30 in the desired direction. Tip: You can turn the entire model on the shifting plate by 180 if necessary. 2. Double-click the Start button of the ineos Blue. An image is acquired. 3. Repeat steps 1 and 2 until all of the required scans have been taken. Tip: Align the scanned area as for the overview scan. Tilt the model holder to an angle of up to 30. Multiple scans are required for angles larger than 30. Start with a small angle and take additional exposures right afterwards with a larger angle. D

38 11 Performing 3D acquisition Sirona Dental Systems GmbH 11.4 Rotational scans Do not turn the model. The lateral alignment must remain the same as for the overview scans Rotational scans Rotational scans Use the rotational scans to acquire single tooth stumps from all sides Preparing the model Preparing the model 1. Move the model holder on the rotation mouse to the 0 position. 2. Secure the object (e.g. a tooth stump) with the fill material in the center of the model holder. The longitudinal alignment of the object must correspond to the model holder's axis of rotation. 3. Tilt the model holder at an angle which enables the undercuts to be recorded (standard: 60 ) Taking a scan Taking a scan 1. Click the icon for rotational scans. 2. Slide the rotation mouse on the shifting plate until the entire object is displayed in the image field. The cable of the rotation mouse should point to the right or left, and not to the front or rear. 3. Rotate the rotation pot until the object remains in the image field in every position. 4. Focus the image with the rotary knobs for height adjustment; see Focusing the image [ 33]. 5. Click the Start button of the ineos Blue. 8 single scans are taken in rapid succession. Tip: You can accelerate the computing process. Align the object so that the distal side points upward Acquiring impressions Acquiring impressions You have selected the bite registration technique "Buccal scan". 38 D

39 Sirona Dental Systems GmbH 11 Performing 3D acquisition Preparing an impression 1. Apply a matte finishing to the areas to be acquired to prevent reflections. An example of a matting agent is CEREC Optispray. 2. Attach the impression tray with the filler material on the rough side of the round plate. 3. Set the plate into the model holder with the oral side facing the column of the ineos Blue. Taking scans It is best to take scans in Free Scan mode. The steps are the same as for exposures of a model. Tip: Be careful not to touch the impression tray when shifting the model. Only touch the model holder. 1. Place a checkmark in front of "Impression Scan" in the selection dialog. Both sides of the model are displayed in the 3D preview. If you click the "Next" icon, the model will be reconstructed from the impression. 2. Check the scan 3D preview. The preparation surface must be completely scanned. Impressions of the upper and lower jaw can only be registered via an exposure of a corresponding buccal impression. The impression should be matted, e.g. using CEREC Optispray, and must be positioned under the camera so that the occlusal plane appears vertically in the live image, and 50% of each half of the jaw is visible. D

40 11 Performing 3D acquisition Sirona Dental Systems GmbH 11.6 Examples 11.6 Examples Examples Scan of a 3-unit bridge Scan of a 3-unit bridge Acquiring a preparation Acquiring a preparation Preparing the model The sliding block is mounted on the model holder. 1. Place the model on the model holder. 2. Tighten the fastening screw until the model is fixed in place. 3. Align the platform in such a way that the model is horizontal. 4. Place the model holder on the shifting plate of the ineos Blue. The oral side points to the column of the ineos Blue. Preparing scans The inlab software is started. 1. Click the "New" button to create a new restoration. The "Select patient for new restoration" window opens. 2. Select a patient you would like to assign the restoration to. A dialog box opens. 40 D

41 Sirona Dental Systems GmbH 11 Performing 3D acquisition 3. Select the type of restoration "Bridge", the allocation "Bite material scan" or "Buccal scan", the Design technique and the teeth concerned and confirm with the "OK" button. A new restoration opens. Acquiring an overview 1. Click the "Preparation" button. The "Acquisition technique" window opens. 2. Select the button for free scans in the "Acquisition technique" window. A section of the model appears in the the live image. 3. Place the model so that the desired section appears in the live image. Start at the distal end. Be careful to include the adjacent teeth in the scan. 4. Focus the image with the rotary knobs for height adjustment; see Focusing the image [ 33]. 5. Single-click the Start button of the ineos Blue to start the automatic scan. The first scan is taken and the crosshairs are displayed blue. If you shift the model or re-focus it, additional scans will automatically be generated. 6. Shift the model and take further exposures until you have a complete overview of the required teeth. Refocus the image if necessary. Tip: The image must overlap approximately one half of the previous image. Interrupt the automatic scan to continue at another location of the model. This location must overlap roughly one half of the image previously scanned. D

42 11 Performing 3D acquisition Sirona Dental Systems GmbH 11.6 Examples 7. To stop acquisition, single-click the Start button of the ineos Blue. Acquiring detail scans 1. Set the angle of the model holder so that the areas required for the design can be completely acquired. Tip: You can rotate the model in the "3D Preview" window. In this way, you can determine whether the information is complete. 2. Click the Start button of the ineos Blue twice to create single scans. The overview image is supplemented. 3. Repeat steps 1 and 2 until all required areas have been covered. Tip: If you have selected "Buccal scan" as the bite registration system, make sure that buccal parts are included in the scan as well Rotational scans Rotational scans Perform the following steps for both abutment teeth. 42 D

43 Sirona Dental Systems GmbH 11 Performing 3D acquisition Preparing the model for rotational scans 1. Fixate the model of the respective tooth in the center of the model pot with filler material. 2. Set the rotation mouse to 60 and place it on the shifting plate of the ineos Blue. Acquisition of rotational scans 1. Select the button for rotational scans in the "Acquisition technique" window. 2. Focus the image with the rotary knobs for height adjustment; see Focusing the image [ 33]. 3. Single-click the Start button of the ineos Blue to start the scan. Eight scans are acquired and included in the preparation. 4. Check whether the preparation surface and the preparation margin were fully acquired. The other scans are displayed transparently. 5. If necessary, acquire further rotational scans at a different angle Acquiring an antagonist Acquiring an antagonist 1. Replace the model in the model holder with the model of the antagonist as described in the section "Preparing the model." 2. Click the "Antagonist" button. 3. Select the button for free scans in the "Acquisition technique" window. A section of the model appears in the the live image. 4. Position the model. Acquire an image of the antagonist section that matches the exposures in the "Preparation"image field. 5. Focus the image with the rotary knobs for height adjustment; see Focusing the image [ 33]. 6. Single-click the Start button of the ineos Blue to start the automatic scan. The first scan is taken and the crosshairs are displayed blue. If you shift the model or re-focus it, additional scans will automatically be generated. 7. Shift the model and take further exposures until you have a complete overview of the required teeth. Refocus the image if necessary. Tip: The image must overlap approximately one half of the previous image. D

44 11 Performing 3D acquisition Sirona Dental Systems GmbH 11.6 Examples 8. To stop acquisition, single-click the Start button of the ineos Blue. Tip: If you selected "Buccal scan" as the bite registration system, you also have to acquire the buccal parts of the antagonist Bite registration Bite registration If you selected "Bite material scan" as the bite registration system in the "New" dialog, you have to acquire an image of the bite registration. 1. Replace the model in the model holder with the model of the preparation as described in the section "Preparing the model." 2. Place the bite registration on the model. 3. Click the "Occlusion" button in the inlab software. 4. Select the button for free scans in the "Acquisition technique" window. A section of the model appears in the the live image. 5. Fasten the models in the holder and place it on the shifting plate of the ineos Blue. The view is located on the preparation. 6. Focus the image with the rotary knobs for height adjustment; see Focusing the image [ 33]. 7. Double-click the Start button of the ineos Blue. An image is acquired. 8. Scan additional images until the required area has been fully acquired Buccal scan Buccal scan If you selected "Buccal scan" as the bite registration system in the "New" dialog, you have to acquire an image of the buccal side. 1. Bring the models of the upper and lower jaws into terminal occlusion. 44 D

45 Sirona Dental Systems GmbH 11 Performing 3D acquisition 2. Fasten the models in the model holder and place it on the shifting plate of the ineos Blue. The occlusal plane is vertical and points toward the column. Scan a location near the preparation. Tip: If you cannot fix the model on the holder, hold the models freely underneath the camera. At the same time, support the model to prevent blurring. 3. Click the "Buccal" button. 4. Double-click the Start button of the ineos Blue. An image is acquired. The preparation and the antagonist can only be combined if sufficient buccal portions were acquired in the image fields "Preparation" and "Antagonist" Terminating acquisition Terminating acquisition The respective teeth, proximal contacts and antagonists have been fully acquired. Click the "Next" button. The program calculates the data Acquisition of a crown cap Acquisition of a crown cap Preparing scans The inlab software is started. 1. Click the "New" button to create a new restoration. The "Select patient for new restoration" window opens. 2. Select a patient you would like to assign the restoration to. A dialog box opens. D

46 11 Performing 3D acquisition Sirona Dental Systems GmbH 11.6 Examples 3. Select the type of restoration "Crown", the Design technique "FrameWork", and the teeth concerned and confirm with the "OK" button. A new restoration opens. Preparing the model for rotational scans 1. Fixate the model of the respective tooth in the center of the model pot with plasticine. 2. Set the rotation mouse to 60 and place it on the shifting plate of the ineos Blue. The tooth must remain completely visible during the rotational movement. Acquisition of rotational scans 1. Select the button for rotational scans in the "Acquisition technique" window. 2. Focus the image with the rotary knobs for height adjustment. 3. Single-click the Start button of the ineos Blue to start the scan. Eight scans are acquired and included in the preparation Exposure of an inlay Exposure of an inlay Acquiring a preparation Acquiring a preparation Preparing the model The sliding block is mounted on the model holder. 1. Place the model on the model holder. 2. Tighten the fastening screw until the model is fixed in place. 3. Align the platform so that the model is positioned horizontally to the model holder plate. 4. Place the model holder on the shifting plate of the ineos Blue. The oral side points to the column of the ineos Blue. 46 D

47 Sirona Dental Systems GmbH 11 Performing 3D acquisition Preparing scans The inlab software is started. 1. Click the "New" button to create a new restoration. The "Select patient for new restoration" window opens. 2. Select a patient you would like to assign the restoration to. A dialog box opens. 3. Select the type of restoration "Inlay", the allocation "Bite material scan" or "Buccal scan", the Design technique and the tooth concerned and confirm with the "OK" button. A new restoration opens. Acquiring an overview 1. Click the "Preparation" button. The "Acquisition technique" window opens. 2. Select the button for free scans in the "Acquisition technique" window. A section of the model appears in the the live image. 3. Place the model so that the desired section appears in the live image. Start with the acquisition of the adjacent tooth. Start at the distal end. Be careful to include the adjacent teeth in the scan. 4. Focus the image with the rotary knobs for height adjustment. 5. Single-click the Start button of the ineos Blue to start the automatic scan. The first scan is taken and the crosshairs are displayed blue. If you shift the model or re-focus it, additional scans will automatically be generated. Tip: If you want to interrupt the automatic scan, single-click the D

48 11 Performing 3D acquisition Sirona Dental Systems GmbH 11.6 Examples Start button of the ineos Blue. The crosshairs turn green. You can resume scanning by clicking the Start button again. 6. Shift the model and take further exposures until you have a complete overview of the required teeth. Refocus the image if necessary. Tip: The image must overlap approximately one half of the previous image. Interrupt the automatic scan to continue at another location of the model. This location must overlap roughly one half of the image previously scanned. 7. To stop acquisition, single-click the Start button of the ineos Blue. Acquiring detail scans 1. Tilt the model slightly to acquire the areas of the preparations that have not yet been exposed. 2. Set the angle of the model holder so that the areas required for the design can be completely acquired. Tip: You can rotate the model in the "3D Preview" window. In this way, you can determine whether the information is complete. 48 D