Issue 3 1st September 2006

Transcription

1 COMPONENTS / XPANDA Order Form 48 COMPONENT PARTS / XpANDA ORDER FORM Postcode ref. STOCK CODE DESCRIPTION QUANTITY PRICE DISCOUNT Issue 3 1st September 2006

2 49 12/2007 SECEUROGUARD / SECEUROBAR Order Form /job ref. placed by WIDTH (mm) SECEUROBAR HEIGHT (mm) WINDOW (W) OR DOOR (D) SECEUROGUARD SECURITY LEVEL LATTICE BUNCH BOTTOM TRACK LOCK TYPE LOCK POSITION * DRILLING HINGE PRICE X S Bi-PART LEFT RIGHT ASIDE FIXED FOLD- EURO EURO EURO RE- LOW STAND- - NO LOCK - HALF - FULL HIGH MID ( ) ING MOVE (T) ARD LOCK HIGH MID MID BOT- LOW TOP LEFT RIGHT LOW TOM FITTED LOCK LOCK (viewed from inside) *Please refer to pages in the price list to determine Measurements are in mm and denote overall sizes. The product will be manufactured to the sizes provided; no further deduction for tolerances will be applied. which lock positions are Exchange or return is not possible. available. (Examples: bottom running, fixed panel, floating sash, face fixed bottom track, etc.) NET PRICE KEYS Additional blank keys EXTRA HANDLES* Brass handle with rivets *Please note all gates are supplied with handles as standard. LOCKS Max of 50 gates keyed alike, 100 window bars Keyed alike? YES/NO Keyed alike? to previous order (gates only) YES/NO ORDER NUMBER MNFG DATE DESPATCH DATE D&T PROCESSED D&T FAXED ROUTE A B C D E F G H DELIVERY DATE Issue 7 1st December 2007 SPECIAL LPCB RESTRICTIONS SECEUROGUARD 1001 Maximum Height 3000mm Minimum Height 650mm* *1001 gates with a height between 650mm and 999mm will be supplied with the following: Two lock hooks only Lock post welded to leading picket Two rows of 1/2 lattice X Lattice S Lattice

3 ORDER FORMS 50 Assembled Shutter Order Form A B C D E F G H I J K L WIDTH INC. GUIDES (mm) HEIGHT INC. BOX (mm) Window (W) or Door* (D) *Please note shutters installed on bar/servery areas and cabinets will be classified as door shutters. SLATS BOTTOM SLAT TYPE BOX SIZE BUILT BUILT -ON -IN SWIVEL GEARED OPERATION MOTOR ROD SPRING CRANK & LOCK MOTOR +OVER- RIDE EXIT OR CABLE CRANK OR OVER- RIDE SIDE OF OPERATION FITTING SIDE (SEE BELOW) LOCK TYPE (SEE BELOW) LEFT RIGHT I E A B /job ref. placed by FACE FIX SIDE FIX GUIDE RAILS UN- DRILLED TYPE PRICE ( ) You must state in this special requirements section if any of the shutters on this order form will: l Require an anti-fallback device (i.e. second spring or anti-dropbrake) as indicated on the appropriate price table l Be installed out of sight of the control unit used to operate the shutter or controlled by impulse operation l Cover a doorway which is the only point of exit or escape l For advice on overide handle selection please see pages 25, 44 and 53 in the price list. NOTE: If one guide rail is face fixed and one guide rail is side fixed you must clearly state on this order form which guide rail is face and which is side (either left or right as viewed from the flat face of the box). EXTERNALLY FITTED (E) FITTING / LOCK SIDE (see columns J & K) INTERNALLY FITTED (I) ORDER NUMBER MNFG DATE D&T PROCESSED Issue 6 1st December 2007 LOCK TYPE B D&T FAXED ROUTE A B C D E F G H DESPATCH DATE DELIVERY DATE LOCK TYPE A NET PRICE LOCKS Keyed alike? YES / NO EXIT (see column H) If ordering a crank operated shutter or a shutter with manual override please state the type of crank / override handle required. *Please state in Special Requirements if shutter will cover a doorway which is the only point of exit or escape. SIDE OF OPERATION (see column I) For built-on shutters the side for operation is viewed from the flat surface of the box For PVC box built-in shutters operation is viewed from inside the building.

4 51 12/2007 FIXED BARS Order Form /job ref. placed by WIDTH (mm) HEIGHT (mm) BAR TYPE FRAME TYPE DRILLING EXTRAS 50 X 10 ROUND SQUARE 25mm BOX 30mm BOX 40mm BOX TOP LEFT RIGHT BOTTOM CUT OUT LUGS ZINC PRIMER FLAT PRICE ( ) ORDER NUMBER MNFG DATE LOAD DATE D&T PROCESSED D&T FAXED ROUTE A B C D E F G H DESPATCH DATE DELIVERY DATE Issue 1 1st December 2007

5 ORDER FORMS 52 MESH GRILLE Order Form WIDTH (mm) HEIGHT (mm) /job ref. placed by MESH PATTERN FRAME DRILLING EXTRAS 12mm x 12mm 25mm x 25mm DIAMOND SQUARE 25mm flat TOP LEFT RIGHT BOTTOM CUT OUT box angle PRICE ( ) ORDER NUMBER MNFG DATE LOAD DATE D&T PROCESSED D&T FAXED ROUTE A B C D E F G H DESPATCH DATE DELIVERY DATE Issue 1 1st December 2007