Long-range sensing made possible with built-in optical lens Stable long-term sensing Enhanced worksite-friendly installability

Transcription

1 FIBER SENSORS FX-1 SERIES Digital Sensor PNP output type available Timer ight intensity monitor Interference prevention Automatic sensitivity setting FX-1 FX-2 Superior performance and advanced user-friendly multi-functionality enables expert usage on the very first day * Passed the U 991 Environment Test FX- * U 611C-1 compatible, Passed the U 991 Environment Test based on SEMI S2-2. [Category applicable for semiconductor manufacturing: TWW2, Process Equipment] [Applicable standards: U 611C-1] [Additional test / evaluation standards as per intended use: U 991, SEMI S2-2] Conforming to EMC Directive U Recognition FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit ong-range sensing made possible with built-in optical lens Stable long-term sensing Enhanced worksite-friendly installability For the first time in the industry, an optical double coupling lens has been incorporated directly into the fiber sensor itself. This lens maximizes the light emission efficiency, resulting in a tremendous improvement in the sensing range. Sensing ranges with small diameter fibers and ultra-small diameter fibers, which have become very popular in recent years due to the miniaturization of chip components, have been increased by % over previous values achieved with other amplifiers. FX-1 series (Double coupling lens) Emitting element Double coupling lens The lens concentrates the light, greatly increasing emitting efficiency. Conventional fiber sensors (No lens) The newly developed four-chemical emitting element that uses the FX-1 (red ED type) suppresses changes over long periods of time as much as possible, so that a stable light emitting level is maintained. There is very little element deterioration so that stable and accurate sensing can be maintained over long periods. Selectable response time We offer selectable levels to correspond with various applications: the response time!s mode, the ONG mode, perfect for adverse environments, and the mode, especially made for minute detection. Selectable sensing range as per the application Ex.: the FX-1 fiber sensor and the FT-B8 fiber ONG 1,1 mm.7 in ong range mode (ONG): Response time s mm in Standard mode (): Response time 2!s mm.78 in High-speed mode (): Response time!s 18 mm 7.87 in Reduced light intensity mode (): Response time 2!s Our new fiber cutter utilizes a specially developed two-in-one fiber attachment that now makes it possible to cut two fibers simultaneously to exactly the same length. Also, since the fibers can be attached to the amplifier while being fixed in position in the two-in-one fiber attachment, sensitivity changes due to variation in the amount of fiber insertion do not occur. cutter Two-in-one fiber attachment Cut 2 equal length fibers simultaneously mthe mode can be set in the red ED type only. Disperses the light reduces emitting efficiency. 62

2 Easy maintenance, as main and sub units are identical Both main and sub units utilize the same amplifier body. This feature allows for easy mounting in the side-by-side configuration. The main and sub unit functions are distinguished only by the proper use of -core main cable and the 1-core sub cable. Moreover, by utilizing the same body for both main and sub units, inventory management and maintenance is simplified. Main cable CN-7-C Identical part numbers eliminate the need for costly inventory management labor Sub cable CN-71-C Wiring- and labor-saving design allows sideby-side configuration for up to sixteen units Up to sixteen amplifiers can be connected in a side-by-side configuration. As the sub cable contains only one output line, a great amount of wiring and space can be saved. Also, special sliding connectors have been provided for all main and sub cables, which can be detached merely by releasing the lock and pulling directly back, without having to slide the amplifier body to the side. Using this connector system, only a minimal amount of space is required for regular maintenance. Sliding connectors are easy to insert and remove Even beginners can quickly learn how to use the MODE NAVI Environmentally friendly packaging FX-1 With regard to effects on the environment, we only utilize the simplest of packaging methods greatly contributing to the reduction in wastes generated by your worksite. Also, the bags are made of polyethylene, a substance that doesn t give off polluting gases when burned. Polyethylene packaging FIBER SENSORS FX-1 FX-2 FX- MODE NAVI uses six indicators to display the amplifier s basic operations. The current operating mode can be confirmed at a glance, so even a first time user can easily operate the amplifier without becoming confused. RUN This is the sensing mode. Incident light level is displayed in the digital display. PUSH PRO This mode allows the selection of further advanced functions, such as the copying of individual settings and the memory functions. PUSH PUSH TEACH This mode is for setting the threshold value. TIMER This mode permits the choice of using or not using the timer. The use of only two switches makes for very simple operations Only two switches, the large jog switch and the large MODE key, are required for operation. Depressing the large MODE key sets the mode selection and mode cancel functions. The large jog switch is used to select from the detailed functions available within each mode, as well as to change numerical values after the mode has been chosen. PUSH PUSH ADJ In this mode, the threshold value, once set, may be fine-tuned. PUSH /D ON This mode allows the selection of output operation as either ight-on or Dark-ON. Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A arge MODE key arge jog switch 1 2 Pressing the switch selects or cancels the operating mode Moving the switch from side to side allows items to be selected Pressing the switch then confirms the selected setting 6

3 FIBER SENSORS FX-1 FX-1 types of light sources available In addition to our red ED (four-chemical emitting element) type, the blue, green, and infrared ED types are also provided to correspond to your specific application. Optical communication function lets multiple sensors be adjusted all at once The optical communication function allows the data that is currently set to be copied and saved all at once for all amplifiers connected together from the right side. This greatly reduces troublesome setup tasks and makes setup much smoother. Single copy & save operation for all amplifiers Equipped with each type of timer These sensors are equipped with types of timers, ON-delay, OFF-delay, and ONE SHOT, for compatibility to variegated environments. ON-delay timer This function is useful for sensing only objects taking a long time travel. OFF-delay timer This function is useful when the connected device has a slow response time. ONE SHOT timer This function is useful when the input specifications of the connected device require a signal of fixed width. FX- FX-2 FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit Easy code input setting Sensing condition ON-delay OFF-delay ONE SHOT Every function can be directly set merely by the input of a four digit code (numbers) from the code table. This convenient feature is easy to set up. In the event that settings are accidentally changed at the operating site, merely entering the correct code can restore the original settings. This results in easy and quick maintenance. Invertible digital display First digit: Settings for response time and hysteresis Second digit: Settings for /D ON and display mode Fourth digit: Timer settings Third digit: Settings for Adjust lock and timer The digital display can be inverted as per its orientation once mounted onto the amplifier. Conventional model FX-1 SERIES turn OFF status T1 T1 T1 T1 T1 T1 T1 : Timer period [Code setting table] Direct First digit Second digit Third digit Fourth digit code Response time Hysteresis /D ON Display mode Adjust lock Timer Timer setting ONG ONG ONG H-2 (standard) H- (large) H-1 (small) H-2 (standard) H- (large) H-1 (small) H-2 (standard) H- (large) H-1 (small) H-2 (standard) -ON -ON -ON -ON D-ON D-ON D-ON D-ON digit % Peak hold Bottom hold digit % Peak hold Bottom hold ON ON ON ON OFF OFF OFF OFF OFF OFF-delay ON-delay ONE SHOT OFF OFF-delay ON-delay ONE SHOT OFF 1 ms ms ms 1 ms ms ms 1 ms ms ms represents a description of the setting in the picture on the left. Selectable cable length Made available are lengths, 1 m.281 ft,, and m 16. ft, to suit your application requirements. This helps reduce the waste caused by cutting cables and lightens the installation workload. Used for intermediate terminal block Directly connected to the PC To PC To PC m 16. ft cable length type turn ON status m 16. ft 1 m.281 ft 6

4 FX-CH Sensor-PC connection system This wire-saving system enables the collective connection of up to 16 I/O devices with an MI connector. Scattered installation is also possible with the help of a sensor separate unit. (Refer to p.876 l for details) Optional units for greater freedom and control when installing SC SERIES Bank selection unit Without directly manipulating the sensor itself, you can simultaneously switch up to 16 fiber sensors settings using an external emitted signal. (oad and save) malso possible with the FX-1 series databank function (Refer to p.1 l for details) FX-1 FX-CH SERIES FIBER SENSORS Inductive proximity sensor Morning ot All settings are changed in a single step Afternoon ot Custom circuit board PC Photoelectric sensor Cylinder switch Micro photoelectric sensor Signal for changing the settings FX-1 Simultaneous settings changes Main unit Separate unit 8-channel connector input extension unit 1-channel connector input extension unit OK Channel 1 NG No cap present Simultaneous settings changes OK Channel 2 NG No cap present FX-2 APPICATIONS FX- Workpieces detection This standard type of FX-1 using red light has a four-chemical emitting element for stable sensing over long periods. Sensing semi-transparent stickers The blue ED type greatly reduces the dampening rate, making it ideal for delicate sensing. FX-1B Sensing register marks The green ED type can accurately discriminate between red and yellow, that cannot be easily detected using red ED type. Red Yellow FX-1G Manually Set Bank Unit FX-11 FX-CH Sensing film meandering Infrared ED type is ideal for sensing environments with light restrictions, such as places where light-sensitive film is being handled. (The emission peak wavelength: 9 nm.7 mil.) It includes full-auto teaching function which allows sensitivity to be set without stopping the workpiece line. Detecting chip component Because of low light intensity fluctuations when detecting minute moving objects, decrease the hysteresis in PRO mode and accurate sensing will be possible in highspeed mode. This method is optimal for chip component verification in taping equipment. Detecting register marks on a transparent sheet When detecting registration marks on transparent film with a thru-beam type, the (reduced light intensity) mode will enable minute light intensity fluctuation sensing. Color Detection Analog Output FZ-1 FX-11A FX-1H FT-FM2 6

5 FIBER SENSORS FX-1 ORDER GUIDE Amplifiers Quick-connection cable is not supplied with the amplifier. Please order it separately. Type Appearance Model No. Emitting element Output FX-1 Digital NPN output PNP output FX-1 FX-1B FX-1G FX-1H FX-1P FX-1BP FX-1GP FX-1HP Red ED Blue ED Green ED Infrared ED Red ED Blue ED Green ED Infrared ED NPN open-collector transistor PNP open-collector transistor FX- FX-2 FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit Quick-connection cables Type Model No. Description Main cable Sub cable End plates OPTIONS CN-7-C1 CN-7-C2 CN-7-C CN-71-C1 CN-71-C2 CN-71-C Quick-connection cable is not supplied with the amplifier. Please order it separately. ength: 1 m.281 ft ength: ength: m 16. ft ength: 1 m.281 ft ength: ength: m 16. ft Appearance Model No. Description MIN-E. mm 2 -core cabtyre cable, with connector on one end Cable outer diameter: ". mm ".118 in. mm 2 1-core cabtyre cable, with connector on one end Cable outer diameter: ". mm ".118 in When cascading multiple amplifiers, or when it moves depending on the way it is installed on a DIN rail, these end plates ensure that all amplifiers are mounted together in a secure and fully connected manner. Two pcs. per set Designation Model No. Description Amplifier mounting bracket MIN-2 Main cable CN-7-C Sub cable CN-71-C End plates are not supplied with the amplifier. Please order separately when the amplifiers are mounted in cascade. Mounting bracket for amplifier Amplifier mounting bracket MIN-2 amplifier protective seal FX-MB1 1 sets of 2 communication window seals and 1 connector seal Communication window seal: It prevents malfunction due to transmission signal from another amplifier, as well as, prevents effect on another amplifier. Connector seal: It prevents contact of any metal, etc., with the pins of the quickconnection cable. amplifier protective seal FX-MB1 Communication window seal Connector seal 66

6 IST OF FIBERS Standard fibers [ (one pair set)] Type Standard ong sensing range Elbow Side-view Shape of fiber (mm in) With lens With lens ens mountable ens mountable Sleeve 9 mm. in "1. ".9 "1. ".9 "2. ".98 "1 ".9 "2 ".79 "1 ".9 M1 "2. ".98 "1.8 ".8 Sleeve mm 1.7 in ens mountable "1.8 ".8 Sleeve 9 mm. in M "2. ".98 M M ".88 ". Sleeve mm 1.7 in ens mountable M ".88 ". " ".7 Sleeve part cannot be bent. Sleeve part cannot be bent. "2. ".98 Sleeve part cannot be bent. Sensing range (mm in ) (Note 1) Red ED Blue ED Green ED Infrared ED 19, 767,7 1, , 9.7, , , ,, , , , ,.118 1, , (Note ) , 1, :ONG : : : Min. sensing object under the optimum condition (Note 2) ". mm ".16 in ".m ".8 in ". mm ".16 in ". mm ".12 in ". mm ".12 in ". mm ".12 in ".2 mm ".1 in ". mm ".16 in ". mm ".19 in ".m ".8 in FX-1 Allowable bending radius R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in Sleeve R1 mm R.9 in R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in Sleeve R1 mm R.9 in R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in FT-FM1 FT-SFM2 FT-B8 FT-NB8 FT-FM2 FT-FM2S FT-FM2S FT-T8 FT-SFM2 FT-N8 FT-NFM2 FT-NFM2S FT-NFM2S FT-SNFM2 FT-R8 FT-V1 FT-SFM2SV2 FT-V22 FT-V1 Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. In addition, the infrared type is easily affected by humidity, so contact our office if using these sensors in environments with high humidity or where humidity levels can fluctuate. Notes: 2) The minimum sensing object size is the value for red ED type. Please contact our office for information on the minimum sensing object size if using amplifiers other than red ED type. The optimum condition is the condition when the sensitivity is set so that the sensing output just changes to light incident operation in the object absent condition. Notes: ) Sensing range for a long fiber. A 1 m 2.88 ft long fiber will cause damping of the beam and cannot be used. Notes: ) The fiber cutter is not supplied as an accessory with FT-NB8 and FT-N8. Please order it separately cable length : 1 m 2.88 ft (Note ) (Note ) 1 m.281 ft R2 mm R.98 in Model No. 67 FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A

7 FIBER SENSORS FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit FX-1 IST OF FIBERS Sharp bending fibers / Flexible fibers [ (one pair set)] Type Sharp bending Flexible Wide beam Rectangular Narrow beam ong sensing range Small diameter Standard Rectangular Side-view Small diameter Standard 68 Shape of fiber (mm in) Wide area sensing Sensing width m 1.26 in WH69D2 W.197H2.717D.787 Wide area sensing Sensing width 11 mm. in W.2H1D1. W.16H1.22D.1 Easy mounting Top sensing WH8D12 W.118H.D.72 Easy mounting Side sensing WH12D8 W.118H.72D. Easy mounting Front sensing W8.H12D W.H.72D.118 Side-view type with small light dispersion " " With lens ong sensing range " ".118 ens mountable 1.9 " ".118 "2. ".98 M "1. ".9 "1 ".9 "2 ".79 Sleeve part cannot be bent. Easy mounting Top sensing WH8D12 W.118H.D.72 Easy mounting Side sensing WH12D8 W.118H.72D. Easy mounting Front sensing W8.H12D W.H.72D.118 ens mountable ens mountable M "1. ".9 "1 ".9 :ONG : Sensing range (mm in) (Note 1) : : Red ED Blue ED Green ED Infrared ED, , 9. 1, , , , , , , 17.79, 17.79, 17.79, (Note ) , ,.118 1, , , , ". mm ".12 in ".2 mm ".1 in ".8 mm ". in ". mm ".2 in ". mm ".16 in ".6 mm ".2 in ".m ".8 in cable Allowable length bending : radius Model No. FT-WA FT-WA8 FT-WZ8H FT-WZ8E FT-WZ8 FT-WKV8 FT-WS8 FT-W8 FT-WS FT-WS8 FT-WV2 FT-Z8H FT-Z8E FT-Z8 FT-P8 FT-P6 FT-P FT-P2 FT-PS1 Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. In addition, the infrared type is easily affected by humidity, so contact our office if using these sensors in environments with high humidity or where humidity levels can fluctuate. Notes: 2) The minimum sensing object size is the value for red ED type. Please contact our office for information on the minimum sensing object size if using amplifiers other than red ED type. The optimum condition is the condition when the sensitivity is set so that the sensing output just changes to light incident operation in the object absent condition. Notes: ) The fiber cable length practically limits the sensing range to, mm in long , Min. sensing object under the optimum condition (Note 2) ". mm ".12 in ". mm ".2 in ". mm ".12 in ".m ".8 in ".m ".8 in ". mm ".12 in ". mm ".16 in ".m ".8 in 1 m.281 ft mm in R1 mm R.9 in R1 mm R.9 in R1 mm R.9 in R1 mm R.9 in R1 mm R.9 in R1 mm R.9 in R1 mm R.9 in R1 mm R.9 in R mm R.7 in R mm R.7 in R mm R.7 in FT-W FT-WS

8 IST OF FIBERS Special use fibers [ (one pair set)] Type Special use Wide beam Array Narrow beam Ultra-small diameter Tough flexible Shape of fiber (mm in) Sensing width m 1.26 in WH69D2 W.197H2.717D.787 Sensing width 11 mm. in W.2H1D1. W.16H1.22D.1 Top sensing WHD W.197H.91D.91 Side sensing WHD W.197H.91D.91 Side-view.118 " ".7 ". ".18 ".7 ".16 Side-view W2H1.D2 W.79H.9D Beam diameter: ".12 mm ". in ".2 " ".1 ".118 Sleeve part cannot be bent. Beam diameter: ".2 mm ".1 in ". " ".16 ".118 Sleeve part cannot be bent. ens mountable :ONG : Sensing range (mm in) (Note 1) : : Red ED Blue ED Green ED Infrared ED, , 9. 1, , 1, , 17.79, 17.79, 17.79, (Note ) 2, , , ".2 mm ".1 in Horizontal: ".2 mm ".1 in Vertical: ". mm ".18 in ".6 mm ".2 in ".m ".8 in ".m ".8 in ". mm ".2 in FX-1 Allowable bending radius R2 mm R.98 in R2 mm R.98 in Model No. FT-A8 FT-AFM2 FT-AFM2E FT-K8 FT-KV8 FT-KV1 FT-E12 FT-E22 FT-P81X Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. In addition, the infrared type is easily affected by humidity, so contact our office if using these sensors in environments with high humidity or where humidity levels can fluctuate. Notes: 2) The minimum sensing object size is the value for red ED type. Please contact our office for information on the minimum sensing object size if using amplifiers other than red ED type. The optimum condition is the condition when the sensitivity is set so that the sensing output just changes to light incident operation in the object absent condition. Notes: ) The fiber cable length practically limits the sensing range to, mm in long Min. sensing object under the optimum condition (Note 2) ". mm ".12 in cable length : mm in 1 m.281 ft 1 m.281 ft R1 mm R.9 in R1 mm R.9 in R1 mm R.9 in R mm R.197 in R1 mm R.9 in FT-A FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A 69

9 FIBER SENSORS FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit FX-1 IST OF FIBERS Environment resistant fibers [ (one pair set)] Type Environment resistant Heat-resistant Vacuum Chemical-resistant C 662 F ens mountable C 662 F Sleeve 6 mm 2.62 in Allows flexible wiring 2 C 92 F ens mountable 2 C 92 F ens mountable 1 C 266 F ens mountable ". ".217 "2.1 ".8 Easy mounting Rectangular SEMI S2 compliant W7HD1 W.276H.91D.12 Side-view ens mountable ". ".217 :ONG : Sensing range (mm in) (Note 1) : : Red ED Blue ED Green ED Infrared ED , , 9. 1, 2.866, , 9. 1, ". mm ".16 in ".m ".8 in ". mm ".16 in ".6 mm ".2 in " mm ".7 in ".8 mm ". in ".m ".8 in Allowable bending radius R2 mm R.98 in Sleeve R1 mm R.9 in R2 mm R.98 in R2 mm R.98 in R mm R1.181 in Rm R in R mm R1.181 in Model No. FT-H-M2 FT-H-M2S6 FT-H2W-M1 FT-H2W-M2 FT-H2-M1 FT-H1-FM2 FT-8Y FT-V8Y Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. In addition, the infrared type is easily affected by humidity, so contact our office if using these sensors in environments with high humidity or where humidity levels can fluctuate. Notes: 2) The minimum sensing object size is the value for red ED type. Please contact our office for information on the minimum sensing object size if using amplifiers other than red ED type. The optimum condition is the condition when the sensitivity is set so that the sensing output just changes to light incident operation in the object absent condition. Notes: ) The allowable cutting range is mm in from the end that the amplifier inserted. The vacuum type fiber must be used with the following products as a set. FT-J6: at atmospheric side (one pair set) FV-BR1: Photo-terminal (one pair set) R1 mm R.9 in FT-Z82Y FT-6V FT-6V Semi-standard fibers (Custom made per order) The fiber cable length or sleeve length of the standard fibers can be modified at your request. Select the fiber cable length (symbol ) or the sleeve length (symbol f ) from the table below. Type Standard threaded (free-cut) FT-FM With sleeve FT-FM -S f FT-FM FT-NFM2-S f With large diameter lens Small diameter threaded with sleeve (free-cut) Wide beam 2C 92F heat-resistant C 662F heat-resistant Chemical-resistant Shape of fiber (mm in) Basic model No. FT-WA- FT-WA8- FT-A- FT-A8- FT-H2-M FT-H-M FT-Z8 Y cable length (Unit: m ft) 9.8, 1.12, 16., , 9.21, , , (Note), 9.8, 1.12, 16., , 9.21, , , , , , f Sleeve length (Unit: cm in) 1.9, 2.787, 1.181, 1.7,, , , 8., 9., 1, 11.1, , 2.787, 1.181, 1.7,, , , 8., 9., 1, 11.1, Note: The standard fiber has a fiber cable length and a cm 1.7 in or 9 cm. in sleeve length. Min. sensing object under the optimum condition (Note 2) cable length : 1 m.281 ft 1 m.281 ft (Note ) 1 m.281 ft Correlation between sensing range attenuation coefficient and fiber cable length The longer the fiber cable, the shorter the sensing range. Sensing range attenuation coefficient R2 mm R.98 in cable length (m ft) 7

10 IST OF FIBERS Standard fibers (Reflective type) :ONG : Shape of fiber Sensing range (mm in ) (Note 1, 2) : : Type (mm in) Red ED Blue ED Green ED Infrared ED Standard ong sensing range Side-view Elbow M6 Sleeve 9 mm. in M6 "2. ".98 Sleeve mm 1.7 in M6 "2. ".98 M6 Coaxial Small diameter M " ".118 M6 Sleeve 9 mm. in "1.8 ".8 Sleeve mm 1.7 in "2. ".98 M6 "1.8 ".8 "2 " ".79.8 " Sleeve part cannot be bent. Small diameter "1. " ".9.7 " Sleeve part cannot be bent Min. sensing object at the maximum sensitivity (Note ) ".m ".8 in ".m ".8 in ".m ".8 in ".m ".8 in ".m ".8 in ".m ".8 in ".m ".8 in ".m ".8 in cable length : mm in (Note ) FX-1 Allowable bending radius R2 mm R.98 in R2 mm R.98 in Sleeve R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in Sleeve R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in Model No. FD-B8 FD- FD-FM2 FD-FM2S FD-FM2S FD-T8 FD-T FD-S8 FD-N8 FD-N FD-NFM2 FD-NFM2S FD-NFM2S FD-SNFM2 FD-R8 FD-SFM2SV2 FD-V1 Notes: 1) The sensing range is specified for white non-glossy paper (FD-B8, FD-, FD-FM2, FD-FM2S, FD-FM2S, FD-N8, FD-T8, FD-S8 and FD-R8: mm in, FD-T, FD-N, FD-NFM2, FD-NFM2S, FD-NFM2S, FD-SNFM2, FD-SFM2SV2 and FD-V1: 2m in) as the object. Notes: 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. In addition, the infrared type is easily affected by humidity, so contact our office if using these sensors in environments with high humidity or where humidity levels can fluctuate. Notes: ) The minimum sensing object size is the value for red ED type at maximum sensitivity. Please contact our office for information on the minimum sensing object size if using amplifiers other than red ED type. Also, note that the corresponding setting distance is different from the rated sensing distance. Notes: ) The fiber cutter is not supplied as an accessory with FD-N8 and FD-N. Please order it separately. R1 mm R.9 in R1 mm R.9 in FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A 71

11 FIBER SENSORS FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit FX-1 IST OF FIBERS Sharp bending fibers / Flexible fibers (Reflective type) Type Flexible Sharp bending ong sensing range Standard Small diameter Standard Side-view Fixed-focus reflective High precision Shape of fiber (mm in) ong sensing range Rectangular M6 " ".118 M For sensing minute objects Coaxial " ".118 Glass substrate detection "2 " " ".118 Sleeve part cannot be bent. M6 " ".118 M "1. ".9 W.2H9.D mm W.2H.7D.911 in Sleeve mm 1.7 in "1.8 ".8 Small spot for sensing minute objects Coaxial ens mountable W2H21D W.9H Specular object detection WH19D W.91H :ONG : Sensing range (mm in) (Note 1, 2) : : Red ED Blue ED Green ED Infrared ED to to to to 9. 2 to to to 1.98 to to 1.26 to.1 (Convergent point 8.) 7 to to.72 (Convergent point 8.) 7. to to.72 (Convergent point 8.) Cannot use.6 to..2 to.18 (Convergent point 2.79).9 to 2.7. to.16 (Convergent point 2.79) 1 to 2..9 to.98 (Convergent point 2.79) Cannot use Cannot use Min. sensing object at the maximum sensitivity (Note ) ". mm ".12 in copper wire ".m ".8 in ".m ".8 in "1.9 mm ".7 in metal pipe (gray) ".8 mm ". in ".m ".8 in ".m ".8 in cable length : 1 m.281 ft Allowable bending radius R1 mm R.9 in Sleeve R1 mm R.9 in Model No. FD-WKZ1 FD-W8 FD-W FD-WT8 FD-WS8 FD-WT FD-WG FD-WSG FD-W1 FD-W2 FD-WV2 FD-P8 FD-P6 FD-P FD-P Notes: 1) The sensing range is specified for white non-glossy paper [11 mm in (FD-WKZ1, FD-W8, FD-WT8, FD-WS8 and FD-P8: mm in, FD-WG, FD-WSG, FD-P6 and FD-P: 2m in, FD-W1: glass substrate 11t m t.72 in)] as the object. Notes: 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. In addition, the infrared type is easily affected by humidity, so contact our office if using these sensors in environments with high humidity or where humidity levels can fluctuate. Notes: ) The minimum sensing object size is the value for red ED type at maximum sensitivity. Please contact our office for information on the minimum sensing object size if using amplifiers other than red ED type. Also, note that the corresponding setting distance is different from the rated sensing distance. However, with the fixed-focus reflective type, when the sensitivity is at MAX., it is only possible to detect the minimum size of the sensing object at a distance corresponding to the convergent point. R1 mm R.9 in R1 mm R.9 in R1 mm R.9 in Rm R.79 in R1 mm R.9 in R1 mm R.9 in R mm R.7 in FD-P2 72

12 IST OF FIBERS Special use fibers (Reflective type) Type Special use Wide beam Array High precision Ultra-small diameter Tough flexible iquid level sensing Fixed-focus reflective Shape of fiber (mm in) W7HD W.276H.91D1.181 Side sensing WH2D2 W.197H.787D.787 Coaxial ens mountable Coaxial ens mountable M Coaxial ens mountable M Coaxial ens mountable M Coaxial ens mountable M "1. ". ".9 ".2 Sleeve part cannot be bent. Coaxial " ".6 ".118 ".26 Sleeve part cannot be bent. ". M ".2 Sleeve part cannot be bent. Coaxial ".8 M ".1 M6 Top sensing WH2D2 W.197H.787D.787 Sleeve part cannot be bent. Glass substrate detection SEMI S2 compliant W17H29D.8 W.669H1.12D. Glass substrate detection W2H21D W.9H.827D.7 Specular object detection WH19D W.91H.78D.118 W6H18D1 W.26H.79D.1 Contact type "6 ".26 Mountable on pipe Standard W2H1D2 W.98H.12D.787 Mountable on pipe For PFA, wall thickness 1 mm.9 in pipe W2H1D2 W.98H.12D.787 Small spot for sensing minute objects M Coaxial High precision :ONG : Sensing range (mm in) (Note 1, 2) : : Red ED Blue ED Green ED Infrared ED Cannot use to 2 to to to.79 (Convergent point 8.) to to.6 (Convergent point 8.). to.18 to.91 (Convergent point 8.) Cannot use. to.2 to.7 (Convergent point 2.79) 1 to.8.9 to. (Convergent point 2.79) 1. to..1 to.18 (Convergent point 2.79) Cannot use 2. to to.79 (Convergent point 6.26) to 12.7 to.72 (Convergent point 6.26). to to. (Convergent point 6.26).8 to to.7 (Convergent point 6.26) FX-1 Allowable bending radius Model No. FD-EG1 FD-EG2 FD-EG FD-E12 FD-E22 FD-ENS1 FD-ENM1S1 Notes: 1) The sensing range is specified for white non-glossy paper [11 mm in (FD-A, FD-G, FD-G6X: 2m in, FD-AFM2, FD-AFM2E, FD-P81X: mm in, FD-: glass substrate 762t 1.1 mm t. in, FD-1: glass substrate 11t m t.79 in)] as the object. Notes: 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. In addition, the infrared type is easily affected by humidity, so contact our office if using these sensors in environments with high humidity or where humidity levels can fluctuate. Notes: ) The minimum sensing object size is the value for red ED type at maximum sensitivity. Please contact our office for information on the minimum sensing object size if using amplifiers other than red ED type. Also, note that the corresponding setting distance is different from the rated sensing distance. However, with the fixed-focus reflective type, when the sensitivity is at MAX., it is only possible to detect the minimum size of the sensing object at a distance corresponding to the convergent point. Notes: ) Following is the allowable cutting range from the end that the amplifier is inserted FD-F8Y: 1, mm in, FD-G6X: 7 mm 27.9 in to to.7 to to.. to to to to.. to to to to.7 Applicable pipe diameter: Outer dia. "6 to "26 mm ".26 to "1.2 in transparent pipe [PVC, fluorine resin, polycarbonate, acrylic, glass, wall thickness 1 to mm.9 to.118 in] Applicable pipe diameter: Outer dia. "6 to "26 mm ".26 to "1.2 in transparent pipe [PFA (fluorine resin) or equivalently transparent pipe, wall thickness 1 mm.9 in] Min. sensing object at the maximum sensitivity (Note ) ".m ".8 in ".m ".8 in ".m ".8 in ". mm ".16 in ".m ".8 in (CD glass) ".6 mm ".2 in ". mm ".12 in ".m ".8 in (iquid) (iquid) ".m ".8 in cable length : mm in 1 m.281 ft mm in 1 m.281 ft (Note ) m 16. ft m 16. ft 1 m.281 ft 1 m.281 ft (Note ) R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in R1 mm R.9 in R1 mm R.9 in R2 mm R.98 in R R.7 R1 mm R.9 in Protective tube R mm R1.7 in R mm R.91 in R1 mm R.9 in R1 mm R.9 in FD-A FD-AFM2 FD-AFM2E FD-G FD-G6 FD- FD-1 FD-2 FD- FD-F8Y FD-F1 FD-F91 FD-F FD-F9 FD-P81X FD-G6X 7 FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A

13 FIBER SENSORS FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit FX-1 IST OF FIBERS Environment resistant fibers (Reflective type) Type Environment resistant Heat-resistant Vacuum Shape of fiber (mm in) C 662 F Coaxial M6 C 662 F Sleeve 6 mm 2.62 in "2.8 M6 ".11 in 2 C 92 F Coaxial M6 C 662 F Sleeve 9 mm. in 1 C 266 F M6 M6 "2.1 ".8 in 2 C 92 F Coaxial C 72 F Glass substrate detection Fixed-focus reflective type W19H27D W.78H1.6 D C 6 F Glass substrate detection Fixed-focus reflective type W19H27D W.78H1.6 D.197 :ONG : Sensing range (mm in) (Note 1, 2) : : Red ED Blue ED Green ED Infrared ED to to.91 to 1 to.9 1 to 8.9 to. 2 to 6.79 to ".m ".8 in ".m ".8 in ".m ".8 in ".m ".8 in ".m ".8 in ".m ".8 in 1 m,281 ft 1 m,281 ft 1 m,281 ft Allowable bending radius R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in R2 mm R.98 in Rm R in Model No. FD-H-M2 FD-H-M2S6 FD-H2-M1 FD-H-2S FD-H2-21 FD-H-2 FD-H18-1 FD-H1-FM2 Notes: 1) The sensing range is specified for white non-glossy paper [ mm in (FD-H-2, FD-H18-1: glass substrate mm in)] as the object. Notes: 2) Please take care that the sensing range of the free-cut type fiber may be reduced by 2 % max. depending upon how the fiber is cut. In addition, the infrared type is easily affected by humidity, so contact our office if using these sensors in environments with high humidity or where humidity levels can fluctuate. Notes: ) The minimum sensing object size is the value for red ED type at maximum sensitivity. Please contact our office for information on the minimum sensing object size if using amplifiers other than red ED type. Also, note that the corresponding setting distance is different from the rated sensing distance. The vacuum type fiber must be used with the following products as a set. FT-J6: at atmospheric side (one pair set) FV-BR1: Photo-terminal (one pair set) 1 m,281 ft Semi-standard fibers (Custom made per order) The fiber cable length or sleeve length of the standard fibers can be modified at your request. Select the fiber cable length (symbol ) or the sleeve length (symbol f ) from the table below. Type Standard threaded (free-cut) Basic model No. FD-FM cable length (Unit: m ft) 9.8, 1.12, 16., , 9.21, f Sleeve length (Unit: cm in) Min. sensing object at the maximum sensitivity (Note ) cable length : (Note), 9.8, 1.12, 1.9, 2.787, 1.181, 1.7, 1.2 With sleeve FD-FM -S f 16., , 9.21,, , , 8., , 1, 11.1, Small diameter 1.9, 2.787, 1.181, 1.7,.6 threaded with FD-NFM2-S f, , , 8., sleeve (free-cut) 9., 1, 11.1, C 92F heat-resistant FD-H2-M , 9.8 C 662F heat-resistant FD-H-M Note: The standard fiber has a fiber cable length and a cm 1.7 in or 9 cm. in sleeve length. Sensing range attenuation coefficient R2 mm R.98 in Sleeve R1 mm R.9 in R2 mm R.98 in Sleeve R1 mm R.9 in FD-6V Correlation between sensing range attenuation coefficient and fiber cable length The longer the fiber cable, the shorter the sensing range cable length (m ft) Accessories (attached with fibers) cutter attachment FX-CT2 FX-AT2 (for fixed-length fiber) 7 FX-AT for "2.m ".87 in fiber ( ) FX-AT (for "1 mm ".9 in fiber) FX-AT (for "1. mm ".1 in fiber) FX-AT6 for "1 mm ".9 in and "1. mm ".1 in mixed fiber ( ) Notes: 1) cutter is not supplied as accessory along with FT-NB8, FT-N8, FD-N8 and FD-N. Please order it separately. Notes: 2) The fiber attachment is not attached with FT-N8/NB8/P8 and FD-N8/P8. The previous FX-AT1 attachment is attached with FD-N.

14 FIBER OPTIONS ens (For thru-beam type fiber) Designation Model No. For thru-beam type fiber For reflective type fiber Expansion lens (Note 1) Superexpansion lens (Note 1) Sideview lens Expansion lens for vacuum fiber (Note 1) FX-E1 FX-E2 FX-SV1 FV-E1 Description Increases the sensing range by times or more. Ambient temperature: 6 to C 76 to 662 F Tremendously increases the sensing range with large diameter lenses. Ambient temperature: 6 to C 76 to 662 F Beam axis is bent by 9. Ambient temperature: 6 to C 76 to 72 F Sensing range increases by times or more. Ambient temperature: to 12 C to 28 F FT-B8 FT-FM2 FT-T8 FT-R8 FT-W8 FT-P8 FT-P6 FT-P81X FT-H-M2 FT-H2W-M1 FT-H2W-M2 FT-H2-M1, (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ) 1,6 (Note ) 2,6 1,6 (Note ) 2,, (Note ), (Note ) 2, 2,9, (Note ), (Note ), (Note ) 2, 1, 1, 1,6 (Note ) FX-1 Notes: 1) Be careful when installing the thru-beam type fiber equipped with the expansion lens, as the beam envelope becomes narrow and alignment is difficult. Especially when installing a fiber with many cores (sharp bending fibers and heat-resistant glass fiber) please be sure to use it only after you have adjusted it sufficiently. Notes: 2) The sensing ranges are the values for red ED type amplifier. Please contact our office for details on sensing ranges for other types of amplifiers. Notes: ) The fiber cable length practically limits the sensing range to. mm in long (FT-H2W-M1 and FT-H2-M1: 1,6 mm in). ens (For reflective type fiber) Designation Model No. Description Pinpoint Pinpoint spot of ". mm ".2 in. Enables detection of minute objects or small marks. FX-MR1 spot lens Applicable fibers: FD-WG, FD-G Distance to focal point: 61 mm.26.9 in Ambient temperature: to 7 C to 8 F Zoom lens Finest spot lens Finest spot lens Zoom lens Side-view type ( ) FX-MR2 FX-MR FX-MR6 FX-MR Screw-in depth Distance to focal point Distance to focal point Distance to focal point Spot diameter Spot diameter Screw-in depth Spot diameter The spot diameter is adjustable from ".7 mm ".28 in to "m ".79 in according to how much the fiber is screwed in. Applicable fibers: FD-WG, FD-G Ambient temperature: to7 C to 8 F Accessory: MS-EX- (mounting bracket) Extremely fine spot of ". mm ".12 in approx. achieved. Applicable fibers: FD-WG, FD-G, FD-EG1,FD-EG2, FD-EG, FD-G6X, FD-G6 Ambient temperature: to 7 C to 8 F Extremely fine spot of ".1 mm ". in approx. achieved. Applicable fibers: FD-WG, FD-G, FD-EG1,FD-EG2, FD-EG, FD-G6X, FD-G6 Ambient temperature:2 to 6 C to 1 F FX-MR2 is converted into a side-view type and can be mounted in a very small space. Applicable fibers: FD-WG, FD-G Ambient temperature: to 7 C to 8 F Sensing range (mm) [ens on both sides] (Note 2) Mode ONG FT-B8 FT-FM2 FT-R8 FT-W8 FT-P8 FT-P6 FT-P81X FT-H-M2 FT-H2W-M1 FT-H2W-M2 FT-H2-M1 FT-H1-FM2, (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ) 1,6 (Note ), (Note ) 1,6 (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ) 1,6 (Note ), (Note ) 1,6 (Note ), (Note ) Note: The sensing ranges are the values when used in combination with red ED type amplifier. Please contact our office for details on sensing distances for other types of amplifier. 2, 2, 2, 1,6 2, 2, 1, 2, 1, 9 9 1,1, (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ) 1,6 (Note ), 1,6 (Note ), (Note ) 1, 1, 1, 8 1, 1,1 9 1,1 7 9 Sensing range (mm) [ens on both sides] (Note 2) Mode ONG Sensing range (mm) [ens on both sides] (Note 2) Mode FT-B8 FT-FM2 FT-T8 FT-W8 FT-P8 FT-P6 FT-P81X FT-H-M2 FT-H2W-M1 FT-H2W-M2 FT-H2-M1 FT-6V FT-6V 1,1 1,2 1,2 9 1,2 6 1,2 1 1, (Note ) 2, ,7 1, ,8 1,, (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ), (Note ) 1, 1, 1,6 (Note ), (Note ) ONG Sensing range (mm) [ens on both sides] (Note 2) Mode ONG Sensing range (Note 1) Screw-in depth Distance to focal point 7 mm "18. mm approx. 1m "27 mm approx. 1 mm " mm approx. FD-EG FD-EG2 FD-EG1 FD-WG/G/G6X/G6 7.. mm 7.. mm 7.. mm 7.. mm 9 9 Spot diameter ".7 mm "1.m "2. mm Sensing range (Note 1) Distance to focal point Spot diameter FD-EG FD-EG2 FD-EG1 FD-WG/G/G6X/G6 7. mm 7. mm 7. mm 7. mm ". mm approx. ".m approx. ". mm approx. ". mm approx. Sensing range (Note 1) Distance to focal point Spot diameter Sensing range (Note 1) Screw-in depth Distance to focal point 8 mm 1 mm approx. 1 mm mm approx. 1 mm mm approx. ".1 mm approx. ". mm approx. ".m approx. ". mm approx. Spot diameter ". mm ".8 mm ". mm 7 FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A

15 FIBER SENSORS FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit FX-1 FIBER OPTIONS Others Designation Protective tube For thru-beam type fiber ( Protective tube For reflective type fiber ( ) bender Universal sensor mounting stand (Note 2) cutter Attachment for fixedlength fiber Attachment for "2.m ".87 in fiber Attachment for "1 mm ".9 in fiber Attachment for "1. mm ".1 in fiber Attachment for "1 mm ".9 in / "1. mm ".1 in mixed fiber ) FTP- (. m 1.6 ft) FTP-1 (1 m.281 ft) FTP- (1. m.921 ft) FTP-N (. m 1.6 ft) FTP-N1 (1 m.281 ft) FTP-N (1. m.921 ft) FDP- (. m 1.6 ft) FDP-1 (1 m.281 ft) FDP- (1. m.921 ft) FDP-N (. m 1.6 ft) FDP-N1 (1 m.281 ft) FDP-N (1. m.921 ft) FB-1 MS-AJ1-F MS-AJ2-F FX-CT1 FX-CT2 FX-AT2 FX-AT FX-AT FX-AT FX-AT6 Model No. For thread For M thread For M6 thread For thread Applicable fibers FT-B8 FT-FM2 FT-FM2S FT-FM2S FT-P8 FT-T8 FT-NFM2 FT-NFM2S FT-NFM2S FD-B8 FD-FM2 FD-FM2S FD-FM2S FD-P8 FD-T8 FD-N FD-NFM2 FD-NFM2S FD-NFM2S Description FT-P6 FT-H1-FM2 FT-P FD-T FD-P FD-H1-FM2 The protective tube, made of non-corrosive stainless steel, protects the inner fiber cable from any external forces. The fiber bender bends the sleeve part of the fiber at the proper radius. (Note 1) Horizontal mounting type Vertical mounting type The free-cut type fiber can be easily cut. (Accessory for FT/FD-P8 only) Mounting stand assembly for fiber (For M, or M6 threaded fiber) The free-cut type fiber can be easily cut. Accessory for the free-cut type fiber. Not attached with the FT-N8/NB8/P8 and FD-N8/N/P8 ( ) This is the attachment for the fixed length fiber. (Accessory) This is the attachment for the "2.m ".87 in fiber. (Accessory. Does not attach with the FT-N8/NB8/P8 or the FD-N8/P8.) (Note ) This is the attachment for the "1 mm ".9 in fiber (Accessory. Does not attach with the FD-N.) (Note ) This is the attachment for the "1. mm ".1 in fiber (Accessory) This is the attachment for the "1 mm".9 in / "1. mm ".1 in mixed fiber. (Accessory) Notes: 1) Do not bend the sleeve part of any side-view type fiber or ultra-small diameter type fiber. Notes: 2) Refer to p.2l for details of the universal sensor mounting stand. Notes: ) The conventional FX-AT1 fiber attachment is attached with the FD-N. Protective tube FTP- FDP- bender FB-1 Universal sensor mounting stand MS-AJ1-F MS-AJ2-F Using the arm which enables adjustment in the horizontal direction, sensing can also be done from above an assembly line. 6 rotation 6 rotation 2 2 Angle adjustment:2 Mounting base (Note) cutter FX-CT2 FX-CT1 Height adjustment: mm.96 in approx. Mounting hole for M6 screw Note: The above figure is MS-AJ1-F. The mounting base of MS-AJ2-F has a different shape. attachment It s possible to simultaneously cut two fibers to the same length Each fiber (with some exceptions) has a newly developed two-in-one fiber attachment (FX-AT/AT/AT/AT6) which enables two fibers to be cut simultaneously to the same length with the new fiber cutter (FX-CT2). Also, since the fibers can be attached to the amplifier while being fixed in position in the two-in-one fiber attachment, sensitivity changes resulting from variation in the amount of fiber insertion do not occur. FX-AT2 FX-AT FX-AT/AT/AT6 76

16 SPECIFICATIONS Amplifiers Item Supply voltage Power consumption Output Utilization category Output operation Short-circuit protection Response time Sensitivity setting Operation indicator Stability indicator MODE indicator Digital display Fine sensitivity adjustment function Timer function Automatic interference prevention function Environmental resistance Pollution degree Ambient temperature Ambient humidity Ambient illuminance EMC Type Model No. Voltage withstandability Insulation resistance Vibration resistance Shock resistance Emitting element (modulated) Material Connecting method Cable extension Weight <Red ED / Infrared ED type> Normal operation: 96 mw or less Current consumption ma or less at 2 V supply voltage ECO mode: 6 mw or less Current consumption 2 ma or less at 2 V supply voltage NPN open-collector transistor Maximum sink current:1 ma are connected in cascade. Applied voltage: V DC or less (between output and V) Residual voltage: 1. V or less at 1 ma (at ma, if five, or more, amplifiers are connected in cascade) sink current. 12 to 2 V DC1 % Ripple P-P 1 % or less FX-1 NPN output PNP output Red ED Blue ED Green ED Infrared ED Red ED Blue ED Green ED Infrared ED FX-1 FX-1B FX-1G FX-1H FX-1P FX-1BP FX-1GP FX-1HP ( ) <Blue ED / Green ED type> Normal operation: 7W or less Current consumption ma or less at 2 V supply voltage ECO mode: mw or less Current consumption 18 ma or less at 2 V supply voltage PNP open-collector transistor Maximum source current: 1 ma ma, if five, or more, amplifiers ma, if five, or more, amplifiers ( ) ( are connected in cascade. ) Applied voltage: V DC or less (between output and V) Residual voltage: 1. V or less at 1 ma (at ma, if five, or more, amplifiers are connected in cascade) source current. DC-12 or DC-1 Selectable either ight-on or Dark-ON, with jog switch Incorporated!s or less (), 2!s or less [ / (Red ED type only)], s or less (ONG) selectable with jog switch 2-level teaching / imit teaching / Manual adjustment / Full auto-teaching (excluding red ED type) Orange ED (lights up when the output is ON) Green ED (lights up under stable light received condition or stable dark condition) RUN: Green ED, TEACH ADJ /D ON TIMER PRO: Yellow ED digit red ED display Incorporated Incorporated with variable ON-delay / OFF-delay / ONE SHOT timer, switchable either effective or ineffective. (timer period:. to ms approx.) Incorporated (Up to four sets of fiber s can be mounted close together) (Note 1) (Industrial environment) 1 to C 1 to 11 F If to 7 units are connected in cascade: 1 to C 1 to 122 F, ( if 8 to 16 units are connected in cascade: 1 to C 1 to 11 F) (No dew condensation or icing allowed), Storage: 2 to 7 C to 8 F to 8 % RH, Storage: to 8 % RH Sunlight: 1,x at the light-receiving face, Incandescent light:,x at the light-receiving face Red ED type: EN 81-2, EN 82-2, EN Blue / green / infrared ED type: EN , V AC for one min. between all supply terminals connected together and enclosure (Note 2) 2 MΩ, or more, with 2 V DC megger between all supply terminals connected together and enclosure (Note 2) 1 to Hz frequency,.7 mm. in amplitude in X, Y and Z directions for two hours each 98 m/s 2 acceleration (1 G approx.) in X, Y and Z directions for five times each Red ED Blue ED Green ED Infrared ED Red ED Blue ED Green ED Infrared ED Enclosure: Heat-resistant ABS, Case cover: Polycarbonate, Switch: Acrylic Connector (Note ) Extension up to total 1 m 28.8 ft is possible with. mm 2, or more, cable. 2 g approx. ( ) ( ) ( ) FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A Notes: 1) When the power supply is switched on, the emission timing are automatically set for interference prevention. Notes: 2) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only. Notes: ) The cable for amplifier connection is not supplied as an accessory. Make sure to use the optional quick-connection cable given below. Main cable (-core): CN-7-C1 (cable length 1 m.281 ft), CN-7-C2 (cable length ), CN-7-C (cable length m 16. ft) Sub cable (1-core): CN-71-C1 (cable length 1 m.281 ft), CN-71-C2 (cable length ), CN-71-C (cable length m 16. ft) 77

17 FIBER SENSORS FX-1 SPECIFICATIONS s Item Type Standard Flexible Allowable bending radius R2 mm R.98 in or more [Sleeve of a with sleeve:r1 mm R.9 in or more (Note 1)] R mm R.7 in or more Bending durability Ambient temperature Ambient humidity 1 million times or more (at R1 mm R.9 in, FT-P/P2 and FD-P/P2: at R mm R.7 in) to 7 C to 8 F FT-SFM2SV2: 2 to 7 C to 8 F to 7 C to 8 F ( FT-V22, FD-SFM2SV2: 2 to 6 C to 1 F FT-V1, FD-V1, FT-V1: to 6 C to 1 F ) ( FT-Z8, FT-P6, FT-PS1, FD-P6, FD-P: ) to 6 C to 1 F to 8%RH (No dew condensation or icing allowed) FX- FX-2 FX-1 FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit Material core Sheath Accessories (Note 2) Polyethylene (FT-V22: Polyolefin) Brass (Nickel plated) FT-SFM2/T8/SFM2/SNFM2/SFM2SV2/V22/V1, FD-T8/T/S8/SNFM2/SFM2SV2/V1 and Sleeve: Stainless steel (SUS) FT-FM1: ABS, ens of FT-FM1/SFM2/V1: Acrylic FT-V1: Stainless steel (SUS) and Polycarbonate All fibers (except for FT-NB8/N8 and FD-N8/N): 1 fiber attachment set type fibers (except for FT-NB8/N8 and FD-N8/N): FX-CT2 (fiber cutter) 1 pc. Threaded fibers: Nuts 2 pcs. (thru-beam type: pcs.) and toothed lock washer 1 pc. (thru-beam type: 2 pcs.) R2 mm R.98 in or more Acrylic to 8 %RH (No dew condensation or icing allowed) Vinyl chloride (FT-PS1: Polyethylene, FD-P2: Vinyl chloride and Polyurethane) Stainless steel (SUS) FT/FD-P8, FT-P6: Brass (Nickel plated) Case of FT-Z8: Polycarbonate ens of FT-Z8H/Z8E, Front film of FT-Z8: Polyester All fibers: 1 fiber attachment set. (except for FT-P8 and FD-P8) type fibers: FX-CT2 (fiber cutter) 1 pc. (FT/FD-P8: FX-CT1 1 pc.) Threaded fibers: Nuts 2 pcs. (thru-beam type: pcs.) and toothed lock washer 1 pc. (thru-beam type: 2 pcs.), FT-Z8: 1 set of mounting screw Notes: 1) Sleeve part of side-view fiber cannot be bent. Notes: 2) The five types of attached fiber attachments (FX-AT2/AT/AT/AT/AT6) described in this catalog are for use only with the FX-1/2//11 series. Refer to p.76 for details FIBER OPTIONS. attachment accessories are also supplied along with conventional amplifiers. Please contact our office for more details on these accessories. Item Type Sharp bending Allowable bending radius Ambient temperature Ambient humidity core Sheath Material Accessories (Note) R1 mm R.9 in or more (FD-WG/WSG: Rm R.79 in or more, Sleeve of FD-W: R1 mm R.9 in or more) to 6 C to 1 F (FT-WA/WA8/WKV8: to C to 11 F) to 8 %RH (No dew condensation or icing allowed) Acrylic Polyethylene Stainless steel (SUS) (including sleeve) FT-W8/W, FD-W8/W/WG: Brass (Nickel plated) Case of FT-WA/WA8/WZ8, ens of FT-WS8 and Resin part of FT-WKV8: Polycarbonate, ens of FT-WA: Norbornene resin ens of FT-WA8: Polyolefin, ens of FT-WZ8H/WZ8E, Reflector of FT-WZ8E and Prism of FT-WKV8: Acrylic, Reflector of FT-WZ8: Polycarbonate, FD-W1: Heat-resistant ABS, Front film of FD-W1: Polyester, FD-W2: Aluminum (Black AMITE), ens of FD-WKZ1: Optical lens ( ) All fibers: 1 fiber attachment set and FX-CT2 (fiber cutter) 1 pc. Threaded fibers: Nuts 2 pcs. (thru-beam type: pcs.) and toothed lock washer 1 pc. (thru-beam type: 2 pcs.) FT-WA:.m in seal type slit mask 2 pcs. FT-WA8:.1m.2.72 in seal type slit mask 2 pcs. and 11m.9.72 in seal type slit mask 2 pcs. FT-WZ8: 1 set of mounting screw FD-WKZ1: mounting bracket 1 pc. Note: The five types of attached fiber attachments (FX-AT2/AT/AT/AT/AT6) described in this catalog are for use only with the FX-1/2//11 series. Refer to p.76 for details FIBER OPTIONS. attachment accessories are also supplied along with conventional amplifiers. Please contact our office for more details on these accessories. Type Special use Item Wide beam Array Narrow beam High precision Allowable bending radius Ambient temperature Ambient humidity FT-A/A8: R1 mm R.9 in or more FD-A: R2 mm R.98 in or more FT-A, FD-A: to 6 C to 1 F FT-A8: to 7 C to 8 F to 7 C to 8 F R2 mm R.98 in or more (FT-KV1: R1 mm R.9 in or more) to 6 C to 1 F FD-EG2/EG: R1 mm R.9 in or more FD-G/G6/EG1: R2 mm R.98 in or more 2 to 6 C to 1 F FD-G: to 7 C to 8 F FD-G6: to 6 C to 1 F ( ) Material core Sheath Accessories (Note) 78 Acrylic Polyethylene Polyolefin (FD-G/G6: Polyethylene) Polycarbonate Stainless steel (SUS), Polycarbonate ens of FT-A, FD-A: Norbornene resin Brass (Nickel plated) ens: Norbornene resin Brass (Nickel plated) ( ens of FT-A8: Polyolefin ) ( ens of FT-KV1: Polycarbonate, Prism of FT-KV8: Acrylic) [FD-G6: Stainless steel (SUS)] All fibers: 1 fiber attachment set and FX-CT2 (fiber cutter) 1 pc. FT-A:.m in seal type slit mask 2 pcs. FT-A8:.1m.2.72 in seal type slit mask 2 pcs. and 1 1m.9.72 in seal type slit mask 2 pcs. All fibers: 1 fiber attachment set type fibers: FX-CT2 (fiber cutter) 1 pc. Threaded fibers: Nuts 2 pcs. and toothed lock washer 1 pc. Note: The five types of attached fiber attachments (FX-AT2/AT/AT/AT/AT6) described in this catalog are for use only with the FX-1/2//11 series. Refer to p.76 for details FIBER OPTIONS. attachment accessories are also supplied along with conventional amplifiers. Please contact our office for more details on these accessories.

18 SPECIFICATIONS s Type Special use Item Ultra-small diameter Fixed-focus reflective Tough flexible Allowable bending radius Ambient temperature Ambient humidity core Material Sheath Accessories (Note 2) FT-E12/E22: R mm R.197 in or more (Note 1) FD-E12: R1 mm R.9 in or more (Note 1) FD-E22/ENS1/ENM1S1: R2 mm R.98 in or more (Note 1) FT-E12/E22, FD-E22: to 7 C to 8 F FD-E12: to 6 C to 1 F FD-ENS1/ENM1S1: 2 to 6 C to 1 F Polyolefin Brass (Nickel plated) [Sleeve: Stainless steel (SUS)] All fibers: 1 fiber attachment set Threaded fibers: Nuts 2 pcs. and toothed lock washer 1 pc. R1 mm R.9 in or more (FD-: R mm R.7 in or more) FD-: to 7 C 2 to 8 F FD-1/2: to 6 C to 1 F FD-: to 7 C to 8 F to 8 %RH (No dew condensation or icing allowed) Acrylic Polyethylene [FT-P81X: Vinyl chloride, Polyethylene (FD-2: Vinyl chloride) Protective tube: Stainless steel (SUS)] FD-/1: Heat-resistant ABS FD-: ABS FD-2: Aluminum (Black AMITE) ens of FD-/: Acrylic ( Front film of FD-1: Polyester) All fibers: 1 fiber attachment set and FX-CT2 (fiber cutter) 1 pc. FD-: M2.6 (length 1m.72 in) screws with washers 2 pcs. and nuts 2 pcs. FX-1 R1 mm R.9 in or more to 6 C to 1 F (FD-P81X: to 7 C to 8 F) FT-P81X, FD-P81X: Brass (Nickel plated) FD-G6X: Stainless steel (SUS) All fibers: 1 fiber attachment set, nuts 2 pcs. (thru-beam type: pcs.) and toothed lock washer 1 pc. (thru-beam type: 2 pcs.) FD-G6X: FX-CT2 (fiber cutter) 1 pc. Notes: 1) Sleeve part cannot be bent. Notes: 2) The five types of attached fiber attachments (FX-AT2/AT/AT/AT/AT6) described in this catalog are for use only with the FX-1/2//11 series. Refer to p.76 for details FIBER OPTIONS. attachment accessories are also supplied along with conventional amplifiers. Please contact our office for more details on these accessories. FIBER SENSORS FX-1 FX-2 Special use Type iquid level sensing Item Model No. FD-F8Y FD-F/F9 Protective tube: R mm R1.7 in or more Allowable bending radius R1 mm R.9 in or more : R mm R.91 in or more Ambient temperature Ambient humidity core Sheath Material Accessories (Note 2) Allowable bending radius Ambient temperature Ambient humidity core Sheath Accessories (Note ) to 12 C to 27 F (Note 1) to 1 C to 212 F (Note 1) to 8 %RH (No dew condensation or icing allowed) Polycarbonate Polypropylene (Protective tube: Fluorine resin) C 662 F type C 72 F type 2 C 92 F type 18 C 6 F type 1 C 266 F type R2 mm R.98 in or more (FT-H2W-: R1 mm R.9 in or more, Sleeve of a with sleeve: R1 mm R.9 in or more) 6 to C 76 to 662 F (Note 1, 2) 6 to C 76 to 72 F (Note 1, 2, ) to 8 %RH (No dew condensation or icing allowed) Polyethylene Polyetherimide (ens: Polycarbonate) 1 fiber attachment set, FX-CT2 (fiber cutter) 1pc. Tying bands pcs., anti-slip tubes 2 pcs. Notes: 1) With the liquid sensing fiber, make sure that the temperature of the liquid is also within the ambient temperature range. Notes: 2) The five types of attached fiber attachments (FX-AT2/AT/AT/AT/AT6) described in this catalog are for use only with the FX-1/2//11 series. Refer to p.76 for details FIBER OPTIONS. attachment accessories are also supplied along with conventional amplifiers. Please contact our office for more details on these accessories. Item Material Type Multi-component glass (Note ) Silicone Acrylic Quartz glass (Note ) Stainless steel (SUS) 1 fiber attachment set FX-CT2 (fiber cutter) 1 pc. Heat-resistant 6 to 2 C 76 to 92 F (Note 2) Silicone Inside stainless steel (SUS) spiral tube FD-H2-21: Stainless steel (sus) FT-H2W-: Fluorine resin Brass (Nickel plated) FD-H2-21: Stainless steel (sus) 6 to 18 C 76 to 6 F (Note 2, ) Environment resistant Fluorine resin Stainless steel (SUS) 6 to 1 C 76 to 266 F Brass (Nickel plated) FT-H2W-, FD-H18-1 and FT-H1-FM2: 1 fiber attachment set type fibers: FX-CT2 (fiber cutter) 1 pc. Threaded fibers: Nuts 2 pcs. (thru-beam type: pcs.) and toothed lock washer 1 pc. (thru-beam type: 2 pcs.) Chemical-resistant R mm R1.181 in or more (FT-Z82Y: R2 mm R.98 in or more) to 1 C to 29 F (FT-Z82Y: to 6 C 1 to 1 F) Protective tube: Fluorine resin Sheath: Polypropylene (Sheath of FT-Z82Y: Fluorine resin) 1 fiber attachment set FX-CT2 (fiber cutter) 1 pc. Vacuum Rm R in or more (FT-6V: R mm R1.181 in or more) to 12 C to 28 F Fluorine resin Aluminum Nuts 2 pcs. (thru-beam type: pcs.) and toothed lock washer 1 pc. (thru-beam type: 2 pcs.) Notes: 1) If the fiber is used below C 22 F, its maximum resistable temperature drops to 2 C 92 F. If the side-view lens FX-SV1 is put on the fiber, the allowable maximum temperature drops to C 72 F. (The ambient temperature range of FX-SV1 is from 6 to C 76 to 72 F.) Notes: 2) The ambient temperature of heat-resistant C 662 F type, C 72 F type, 2 C 92 F type and 18 C 6 F type fibers are the value in dry condition. In humid environment, the ambient temperature differs. (For a high humidity of 8 %RH, the ambient temperature is to C 1 to 1 F.) Notes: ) If the fiber material is quartz glass or multi-component glass, keep it away from vibration or impact. Notes: ) The normal temperature for continuous usage or storage should be 6 to C 76 to 2 F. Notes: ) The five types of attached fiber attachments (FX-AT2/AT/AT/AT/AT6) described in this catalog are for use only with the FX-1/2//11 series. Refer to p.76 for details FIBER OPTIONS. attachment accessories are also supplied along with conventional amplifiers. Please contact our office for more details on these accessories. FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A 79

19 FIBER SENSORS FX-1 FX-2 FX-1 I/O CIRCUIT AND WIRING DIAGRAMS I/O circuit diagram Sensor circuit NPN output type Tr D ZD Internal circuit Color code of quick-connection cable (Brown) V (Note 1) (Black) Output 1 ma max. (Note 2) (Blue) V (Note 1) Users circuit oad 12 to 2 V DC 1 % Notes: 1) The quick-connection sub cable does not have V (brown) and V (blue). Notes: 2) ma max., if five amplifiers, or more, are connected together. Symbols D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : NPN output transistor PNP output type Wiring diagram Brown (Note) Black Color code of quick-connection cable Blue (Note) Terminal arrangement diagram V Output V oad + 12 to 2 V DC 1 % Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. FX- I/O circuit diagram Color code of quick-connection cable (Brown) V (Note 1) Wiring diagram Color code of quick-connection cable Brown (Note) FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit Sensor circuit Tr D Internal circuit ZD 1 ma max. (Note 2) (Black) Output oad (Blue) V (Note 1) Users circuit 12 to 2 V DC 1 % Notes: 1) The quick-connection sub cable does not have V (brown) and V (blue). Notes: 2) ma max., if five amplifiers, or more, are connected together. Symbols D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor Black oad Blue (Note) + 12 to 2 V DC 1 % Note: The quick-connection sub cable does not have brown lead wire and blue lead wire. Terminal arrangement diagram V Output V 8

20 SENSING CHARACTERISTICS (TYPICA) Parallel deviation FX-1 The following sensing characteristics pertain to the red ED type. Please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here. FT-FM1 FT-SFM2 FT-B8 FT-NB8 FIBER SENSORS 2, , 9.7 FT-FM2 FT-FM2S FT-FM2S FT-T8 FT-SFM2 FT-V1 FT-V22 ONG 2, 1, 1, eft Center Right 1, ONG 2, 2, 1,.78 ONG eft Center Right 1, FT-NFM2 FT-NFM2S FT-N8 FT-NFM2S FT-SNFM2 FT-R eft Center Right 2, 1, and 1 eft Center Right 1 1, ONG eft Center Right 2, 1, ONG, and Down Center Up FT-SFM2SV2 FT-V1 ONG eft Center Right ONG 1 1 eft Center Right ONG 2 1, ONG 1, 1, eft Center Right ONG eft Center Right Horizontal direction Vertical direction Horizontal direction Vertical direction ONG Horizontal direction ONG 1 1 eft Center Right 2 Vertical direction.78 2 ONG Down Center Up eft Center Right Horizontal direction 2 ONG eft Center Right ONG Down Center Up Vertical direction 2 ONG Down Center Up FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A 81

21 FIBER SENSORS FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit FX-1 SENSING CHARACTERISTICS (TYPICA) Parallel deviation, , 1, 2, , FT-WZ8H Horizontal direction, 7.8 ONG 1, eft Center Right FT-WA FT-A FT-WZ8 Horizontal & vertical directions ONG FT-WS8 2 Vertical direction Horizontal direction 2 2.m.87 in approx. 6 mm.26 in approx (Down) eft Center Right (Up) Vertical direction, 7.8, , 1, 2 2. mm.98 in approx. ONG 1 1 eft Center Right 2 FZ-WZ8E FT-W8 FT-WS8 FT-WS Horizontal direction 2, 1, 9. 1, FT-WA8 FT-A8 Horizontal direction Vertical direction Horizontal direction Vertical direction,,,, ONG ONG ONG ONG, , 1, 19 mm.78 in approx eft Center Right Down Center Up The following sensing characteristics pertain to the red ED type. Please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here., , 1, ONG and eft Center Right eft Center Right Horizontal direction 2, 1, 9. 1, FT-WKV8 ONG, and 2 2, , 1, 2, 1, 9. 1, eft Center Right FT-W FT-WS Down Center Up Vertical direction ONG. mm.217 in approx eft Center Right Vertical direction 2, 1, 9. 1, ONG,,, and 8 mm. in approx eft Center Right , 1, 9. ONG 1, eft Center Right ONG 1 1 eft Center Right ONG 1 1 eft Center Right ONG eft Center Right

22 SENSING CHARACTERISTICS (TYPICA) Parallel deviation FT-WV2 FT-Z8H FT-Z8E FX-1 The following sensing characteristics pertain to the red ED type. Please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here. FIBER SENSORS Horizontal direction 1 ONG eft Center Right 1, Horizontal direction ONG Vertical direction 1 ONG Down Center Up Vertical direction ONG FT-Z8 FT-P8 FT-P6 FT-P Horizontal & Vertical direction vertical directions ONG 6 mm.26 in approx Horizontal direction 2.m.87 in approx (Down) eft Center Right (Up) FT-P2 ONG 1 eft Center Right FT-AFM2E ONG eft Center Right, 7.8, , 1,.78 2 Vertical direction 2. mm.98 in 2 Horizontal & vertical directions ONG (Down) eft Center Right (Up) FT-PS1 FT-AFM2 1 1 ONG eft Center Right mm in approx eft Center Right Down Center Up ONG Horizontal direction 1 1 eft Center Right Horizontal direction ONG 2 2, 1,. mm.217 in Vertical direction Horizontal & vertical directions ONG (Down) eft Center Right (Up) ONG eft Center Right Vertical direction ONG Horizontal direction mm.12 in approx eft Center Right Down Center Up 2, 1, FT-K8 ONG eft Center Right FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A 8

23 FIBER SENSORS FX-1 SENSING CHARACTERISTICS (TYPICA) Parallel deviation FT-KV1 The following sensing characteristics pertain to the red ED type. Please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here. FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit Horizontal direction , 1, ONG eft Center Right FT-KV8 Horizontal direction ONG eft Center Right FT-P81X ONG Vertical direction ONG Down Center Up Vertical direction 2, 1, 1.7 ONG eft Center Right FT-H-M2 FT-H2W-M1 FT-H-M2S6 FT-H2W-M2 FT-H2-M eft Center Right eft Center Right eft Center Right 1, FT-H1-FM2 ONG , eft Center Right ONG FT-E12 ONG eft Center Right FT-8Y FT-V8Y, 7.8, ,.78 ONG eft Center Right ONG Horizontal direction 1, ONG FT-E22 ONG eft Center Right eft Center Right ONG eft Center Right Vertical direction 1, ONG Down Center Up 8

24 SENSING CHARACTERISTICS (TYPICA) Parallel deviation, 7.8, FX-1 FT-Z82Y FT-6V FT-6V ONG 2, 1, eft Center Right Parallel deviation with FX-E1 (expansion lens) applied on both sides, 7.8, , 1, ONG eft Center Right Parallel deviation with FX-E2 (super-expansion lens) applied on both sides ONG 1 eft Center Right FT-B8 FT-W8 FT-P8 FT-H-M2 ONG ens eft Center Right, 7.8, , 1, FT-H2W-M2 ONG ens ens eft Center Right ens, 7.8, , 1, ONG ens eft Center Right 2, 1, 9. 1, FT-H2-M1 ONG ens ens eft Center Right The following sensing characteristics pertain to the red ED type. Please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here. ens 2, 7.8, , 1, ONG ens eft Center Right ens, 7.8, , 1, ONG 1 ens eft Center Right FT-B8 FT-W8 FT-P8 FT-H-M2 ens FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A, 7.8, , 1, ONG,, and ens eft Center Right ens, 7.8, , 1, 2 ONG, and ens 1 1 eft Center Right ens 2, 7.8, , 1, 2 ONG, and ens 1 1 eft Center Right ens 2, 7.8, , 1, ONG,, and ens eft Center Right ens 8

25 FIBER SENSORS FX-1 SENSING CHARACTERISTICS (TYPICA) Parallel deviation with FX-E2 (super-expansion lens) applied on both sides The following sensing characteristics pertain to the red ED type. Please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here. FT-H2W-M2 FT-H2-M1 FT-H1-FM2 FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit Parallel deviation with FX-SV1 (side-view lens) applied on both sides 1, 9. 1, FT-B8 Horizontal direction 2,, 7.8, , 1, ONG ens ens eft Center Right 1, 9. 1, FT-P8 ONG ONG ens eft Center Right Vertical direction 2, ONG eft Center Right 1, 9. 1, ens ens Down Center Up ONG.78 1, FT-W8 Horizontal direction ONG ens ens 1 1 eft Center Right 2 1, ONG ens ens Down Center Up Horizontal direction Vertical direction Horizontal direction Vertical direction 2, 2, ONG FT-H2W-M2 ens ens ens 2, 1, 9. 1, , 9. 1, ONG, and ens 1 1 eft Center Right ens ens Down Center Up ens, 7.8, , 1, 1, FT-H-M2 ONG ONG and ens eft Center Right ens ens eft Center Right FT-H2-M1 ens 1, Vertical direction ens ens Down Center Up 2.78 Horizontal direction Vertical direction Horizontal direction Vertical direction ONG ONG ONG ONG ens ens eft Center Right ens ens Down Center Up eft Center Right Down Center Up

26 SENSING CHARACTERISTICS (TYPICA) Sensing fields FD-B8 White non-glossy paper ONG 1 1 eft Center Right FD-N eft Center Right FD-SFM2SV2 Horizontal direction ONG FX-1 FD- FD-T8 FD-S8 FD-T FD-NFM2 Reflective type FD-NFM2S FD-NFM2S FD-FM2 Reflective type FD-FM2S FD-FM2S Reflective type Reflective type White nonglossy paper eft Center Right Horizontal direction.78 2 FD-WKZ1 White non-glossy paper ONG ONG White nonglossy paper Reflective type White non-glossy paper ONG eft Center Right Vertical direction 1 ONG White nonglossy paper Down Center Up Vertical direction White non-glossy paper ONG eft Center Right Reflective type FD-N Reflective type FD-R eft Center Right 1 Reflective type White non-glossy paper ONG eft Center Right.78 2 White nonglossy paper Emission ONG Down Center Up The following sensing characteristics pertain to the red ED type. Please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here FD-V1 Horizontal direction ONG eft Center Right FD-W8 FD-WT8 FD-WS ONG eft Center Right ONG 1.7 White nonglossy paper Reflective type White nonglossy paper Reflective type Reflective type White nonglossy paper eft Center Right FD-SNFM2 ONG White non-glossy paper eft Center Right Vertical direction 8. ONG White nonglossy paper Down Center Up FD-W FD-WT ONG 1.9 Reflective type White nonglossy paper eft Center Right.7 FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A 87

27 FIBER SENSORS FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit FX-1 Sensing fields FD-WG FD-WSG SENSING CHARACTERISTICS (TYPICA) FD-P6 FD-A Horizontal direction ONG Reflective type White non-glossy paper eft Center Right FD-G ONG Reflective type FD-P Reflective type FD-P White non-glossy paper ONG Reflective type White nonglossy paper eft Center Right 1.9 Reflective type eft Center Right 1 Vertical direction 2 1 FD-WV2 Horizontal direction White nonglossy paper ONG White non-glossy paper Down Center Up FD-G6 ONG eft Center Right ONG White non-glossy paper eft Center Right The following sensing characteristics pertain to the red ED type. Please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here. Reflective type Reflective type.7 Vertical direction FD-AFM2 FD-AFM2E Horizontal direction 1.7 White non-glossy paper ONG eft Center Right FD-EG1 ONG White non-glossy paper ONG White nonglossy paper Down Center Up Reflective type eft Center Right 1.9 Reflective type 1.7 Reflective type Vertical direction 2 1 FD-P8 White nonglossy paper 2 ONG FD-P2 White non-glossy paper 6. mm.22 in approx. ONG Down Center Up FD-EG eft Center Right White non-glossy paper ONG Reflective type 1.7 Reflective type eft Center Right 1.7 Reflective type White non-glossy paper ONG eft Center Right ONG White non-glossy paper eft Center Right White non-glossy paper ONG eft Center Right ONG White non-glossy paper eft Center Right 88

28 SENSING CHARACTERISTICS (TYPICA) Sensing fields FD-EG ONG Reflective type White non-glossy paper eft Center Right FD-ENM1S FD-E12 Reflective type White non-glossy paper ONG eft Center Right FD-E22 Reflective type White non-glossy paper ONG eft Center Right Reflective type FD-P81X Reflective type FD-G6X White non-glossy paper ONG eft Center Right FD-H2-M1 White non-glossy paper ONG 1 1 eft Center Right FD-H1-FM ONG White nonglossy paper eft Center Right ONG 1.9 Reflective type White nonglossy paper eft Center Right Reflective type FD-H-2S Reflective type FD-H2-21 Reflective type ONG White non-glossy paper eft Center Right FD-6V ONG Reflective type 2 White nonglossy paper 1 1 eft Center Right FD-ENS1 FX-1 The following sensing characteristics pertain to the red ED type. Please contact our office for the sensing characteristics pertaining corresponding to types other than the red ED or to types not mentioned here. Reflective type White non-glossy paper ONG Reflective type eft Center Right 1 FD-H-M2 FD-H-M2S White non-glossy paper ONG Reflective type 1 eft Center Right FD-H-2 FD-H Transparent glass ONG 1 Reflective type mm.118 in eft Center Right 2.79 FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A ONG White nonglossy paper 1 1 eft Center Right ONG White nonglossy paper eft Center Right

29 FIBER SENSORS FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit FX-1 PRECAUTIONS FOR PROPER USE Amplifier This product is not a safety sensor. Its use is not intended or designed to protect life and prevent body injury or property damage from dangerous parts of machinery. It is a normal object detection sensor. Mounting How to mount the amplifier 1 Fit the rear part of the amplifier on a mm 1.78 in width DIN rail. 2 Press down the front part of the mounting section of the amplifier on the mm 1.78 in width DIN rail. How to remove the amplifier 1 Push the amplifier forward. 2 ift up the front part of the amplifier to remove it. Note: Take care that if the front part is lifted without pushing the amplifier forward, the hook on the rear portion of the mounting section is likely to break. How to connect the fiber cables 1 Snap the fiber lock lever down. 2 Insert fiber cables slowly into the inlets until they stop. (Note 1) Return the fiber lock lever to the original position, till it stops. Connection Connection method 1 Holding the connector of the quick-connection cable, align its projection with the groove at the top portion of the amplifier connector. 2 Insert the connector till a click is felt. Disconnection method lock lever 1 Pressing the projection at the top of the quick-connection cable connector, pull out the connector. Note: Take care that it the connector is pulled out without pressing the projection, the projection may break. Do not use a quick-connection cable whose projection has broken. Note: Further, do not pull by holding the cable, as this can cause a cable-break Notes: 1) In case the fiber cables are not inserted to a position where they stop, the sensing range reduces. Notes: 2) With the coaxial reflective type fiber, such as, FD-G or FD-FM2, insert the single-core fiber cable into the beam-emitting inlet and the multi-core fiber cable into the beam-receiving inlet. If they are inserted in reverse, the sensing accuracy will deteriorate. 1 2 cable Groove 1 mm 1.78 in width DIN rail Make sure that the power supply is off while connecting or disconnecting the quick-connection cable. Refer to p.11l for general precautions, and to the PRO Mode Operation Guide or SUNX fiber sensor home page ( for details pertaining to operating instructions for the amplifier. Projection Quick-connection cable Projection Cascading amplifiers Make sure that the power supply is off while cascading or removing the amplifier. Make sure to check the allowable ambient temperature, as it depends on the number of amplifiers connected in cascade. In case two, or more, amplifiers are connected in cascade, make sure to mount them on a DIN rail. When connecting in cascade, mount the amplifiers close to each other, fitting them between the optional end plates (MIN-E) mounted at the two ends. When the amplifiers move on the DIN rail depending on the attaching condition, fitting them between the optional end plates (MIN-E) mounted at the two ends. Up to maximum amplifiers can be added (total 16 amplifiers connected in cascade.) When connecting more than two amplifiers in cascade, use the sub cable (CN-71-C) as the quick-connection cable for the second amplifier onwards. Between the FX-1B(P)/G(P)/H(P) and the FX-1(P), the setting status copy function via communication signal cannot be used. If coupling these, please arrange identical models one at a time. Cascading method 1 Mount the amplifiers, one by one, on the mm1.78 in width DIN rail. 1 (For details, refer to Mounting.) 2 Slide the sub units next to the main unit, and connect the quick-connection cables. Mount the optional end plates (MIN-E) at both the ends to hold the amplifiers between their flat sides. Tighten the screws to fix the end plates (MIN-E). Dismantling 1 oosen the screws of the end plates (MIN-E). 2 Remove the end plates (MIN-E). Slide the sub units and remove them one by one. (For details, refer to Mounting.) Main unit Sub unit mm 1.78 in width DIN rail Sub cable (CN-71-C) (optional) Slide Main cable (CN-7-C) (optional) Main cable (MIN-E) (optional) Slide Operation procedure When the power supply is switched on, communication self-check is carried out and normal condition is displayed [MODE indicator / RUN (green) lights up and the digital display shows incident light intensity]. When MODE key is pressed, the mode changes as per the diagram below. Power supply switched on Communication self-check Part description Operation indicator (Orange) MODE indicator / RUN (Green) MODE indicator / TEACH (Yellow) MODE indicator / ADJ (Yellow) 9 Stability indicator (green) MODE indicator / PRO (Yellow) Digital display (Red) MODE indicator / /D ON (Yellow) MODE indicator / TIMER (Yellow) Jog switch MODE key RUN Press MODE key Refer to Teaching on p.91 TEACH Press MODE key Refer to Threshold value ADJ fine adjustment on p.92 Press MODE key Refer to PRO mode PRO on p.9 Press MODE key Refer to TIMER Timer operation setting on p.92 Press MODE key Refer to /D ON Output operation Press MODE key setting on p.92 When jog switch is pressed, the setting is confirmed. When MODE key is pressed for 2 sec., or more, the sensor returns to the RUN mode. Cancellation is possible by pressing MODE key during setting.

30 PRECAUTIONS FOR PROPER USE Amplifier Teaching The threshold values can be set by 2-level teaching, limit teaching or fullauto teaching, when the MODE indicator / TEACH (yellow) lights up. In case of 2-level teaching This is the method of setting the threshold value by teaching two levels, corresponding to the object present and object absent conditions. Normally, setting is done by this method. Step Description Display 1 2 Set the fiber within the sensing range. Press MODE key to light up MODE indicator / TEACH (yellow). Press jog switch in the object present condition. If the teaching is accepted, the read incident light intensity blinks in the digital display. Reflective type Mark Beam blocked Background condition MODE indicator / TEACH (yellow) blinks. Press jog switch in the object absent condition. Reflective type Mark Beam incident Background condition If the teaching is accepted, the read incident light intensity blinks in the digital display and the threshold value is set at the mid-value between the incident light intensities in the object present and the object absent conditions. After this, the judgment on the stability of sensing is displayed. In case stable sensing is possible: is displayed. Stability indicator (green) blinks. In case stable sensing is not possible: blinks. Stability indicator (green) is off. The threshold value is displayed. 6 blinks in the digital display. The incident light intensity appears in the digital 7 display and the setting is complete. Note: Do not move or bend the fiber cable after the sensitivity setting. Detection may become unstable. In case of full auto-teaching FX-1B(P)/G(P)/H(P) only Full auto-teaching is used when it is desired to set the threshold value without stopping the assembly line, with the object in the moving condition. Step Description Display 1 Set the fiber within the sensing range. Press MODE key to light up MODE indicator / TEACH (yellow). Press the jog switch continuously for. sec. or more 2 with the object moving on the assembly line. (The incident light intensity is displayed during sampling.) is displayed on the digital display. Release the jog switch when the object has passed. If the teaching is accepted, the read incident light intensity blinks in the digital display and the threshold value is set at the mid-value between the incident light intensities in the object present and the object absent conditions. After this, the judgment on the stability of sensing is displayed. In case stable sensing is possible: is displayed. Stability indicator (green) blinks. In case stable sensing is not possible: blinks. Stability indicator (green) is off. The threshold value is displayed. 6 blinks in the digital display. The incident light intensity appears in the digital 7 display and the setting is complete. Notes: 1) The threshold value s shift amount can be selected in PRO mode. Refer to the SUNX fiber sensor home page ( for more details pertaining to setting instructions. (Increments of % between and % for setting possible. % default.) Notes: 2) Do not move or bend the fiber cable after the sensitivity setting. Detection may become unstable. FX-1 Refer to p.11l for general precautions, and to the PRO Mode Operation Guide or SUNX fiber sensor home page ( for details pertaining to operating instructions for the amplifier. In case of limit teaching This is the method of setting the threshold value by teaching only the object absent condition (stable incident light condition). This is used for detection in the presence of a background body or for detection of small objects. Step Description Display 1 2 Set the fiber within the sensing range. Press MODE key to light up MODE indicator / TEACH (yellow). Press jog switch in the object absent condition. If the teaching is accepted, the read incident light intensity blinks in the display. Reflective type Beam incident condition Background body MODE indicator / TEACH (yellow) blinks. Turn jog switch to the side or side. If jog switch is turned to the side, scrolls (twice) the display from right to left, and the threshold level is shifted to a value approx. % higher (lower sensitivity) than that set at 2. (Note 1) This is used in case of reflective type fibers. If jog switch is turned to the side, scrolls (twice) the display from left to right, and the threshold level is shifted to a value approx. % lower (higher sensitivity) than that set at 2. (Note 1) This is used in case of thru-beam type fibers. High OFF ON Threshold value % Incident light intensity 1 % % with object absent Threshold value ON OFF ow Turn to side Turn to side Threshold value After this, the judgment on whether the setting shift amount can be shifted or not is displayed. In case shifting is possible: blinks. In case shifting is not possible: blinks. 6 The threshold value is displayed. 7 blinks in the digital display. The incident light intensity appears in the digital 8 display and the setting is complete. Notes: 1) The approx. % amount of shift is the initial value. The amount of shift can be changed in the PRO mode from approx. to 8 % ( % step). Refer to the Sensor Guide Book or SUNX fiber sensor home page ( for more details pertaining to setting instructions. Notes: 2) Do not move or bend the fiber cable after the sensitivity setting. Detection may become unstable. Please refer to p.62 for setting of threshold value when used in combination with liquid level sensing fiber FD-F8Y and to p.618 for setting of threshold value when used in combination with pipe-mountable liquid level sensing fiber FD-F, FD-F9. 91 FIBER SENSORS FX-1 FX-2 FX- Manually Set Bank Unit FX-11 FX-CH Color Detection Analog Output FZ-1 FX-11A

31 FIBER SENSORS FX-1 FX-2 FX- FZ-1 FX-11A FX-11 FX-CH Color Detection Analog Output Manually Set Bank Unit FX-1 PRECAUTIONS FOR PROPER USE Amplifier Threshold value fine adjustment Step Description Display Press MODE key to light up MODE indicator / ADJ (yellow). In case the threshold value is to be increased (sensitivity to be reduced), turn the jog switch to the side to increase the threshold value slowly. If the jog switch is turned continuously to the side, the threshold value increases rapidly. In case the threshold value is to be decreased (sensitivity to be increased), turn the jog switch to the side to decrease the threshold value slowly. If the jog switch is turned continuously to the side, the threshold value decreases rapidly. When jog switch is pressed, the threshold value is confirmed. Output operation setting Step Description Display 1 2 Press MODE key to light up MODE indicator / /D ON (yellow). If the jog switch is turn to the or direction, the output operation setting will change. When jog switch is pressed, the threshold value is confirmed. Timer operation setting The setting for whether the timer is used or not can be done when MODE indicator / TIMER (yellow) lights up. 1 ms OFF-delay (initial value) timer is automatically set when the timer is set to be used. Further, an OFF-delay (initial value) which is useful when the response of the connected device is slow, etc., an ONdelay which is useful to detect only objects taking a long time to travel, and ONE SHOT, which is useful when the input specifications of the connected device require a signal of a fixed width, are possible with the FX-1 series. Refer to the Sensor Guide Book or SUNX fiber sensor home page ( fiber-sensor.com) for the setting method of the OFF-delay, ON-delay and ONE SHOT timer intervals. Refer to p.11l for general precautions, and to the PRO Mode Operation Guide or SUNX fiber sensor home page ( for details pertaining to operating instructions for the amplifier. or Displays present setting ight state Dark state Displays selected setting Key-lock function With the FX-1B(P)/G(P)/H(P), if jog switch and MODE key are pressed for more than sec. at the same time in RUN mode condition, the key operations are locked, and only the threshold value confirmation function or the adjust function (valid only when the adjust lock function is canceled) is valid. To cancel the lock function, press both the keys for more than sec. once again. Wiring Make sure that the power supply is off while wiring. Verify that the supply voltage variation is within the rating. Take care that if a voltage exceeding the rated range is applied, or if an AC power supply is directly connected, the sensor may get burnt or damaged. If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground. In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this product, connect the frame ground (F.G.) terminal of the equipment to an actual ground. Take care that short-circuit or wrong wiring of the load may burn or damage the sensor. Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction. Ensure that an isolation transformer is utilized for the DC power supply. If an auto transformer is utilized, the main amplifier or power supply may be damaged. Make sure to use the optional quick-connection cable for the connection of the amplifier. Extension up to total 1 m 28.8 ft is possible with. mm 2, or more, cable. However, in order to reduce noise, make the wiring as short as possible. Others Do not use during the initial transient time (. sec. approx.) after the power supply is switched on. Take care that the sensor is not directly exposed to fluorescent light from a rapid-starter lamp or a high frequency lighting device, as it may affect the sensing performance. This sensor is suitable for indoor use only. Avoid dust, dirt, and steam. Take care that the product does not come in direct contact with water, oil, grease, or organic solvents, such as, thinner, etc. This sensor cannot be used in an environment containing inflammable or explosive gasses. Never disassemble or modify the sensor. (Note) Note: The OFF-delay timer interval set in the PRO mode is displayed. Refer to the Sensor Guide Book or SUNX fiber sensor home page ( fiber-sensor.com) for more details. 92

32 PRECAUTIONS FOR PROPER USE Amplifier PRO mode Refer to the Sensor Guide Book for more details pertaining to the PRO mode settings and procedures. FX-1 Refer to p.11l for general precautions, and to the PRO Mode Operation Guide or SUNX fiber sensor home page ( for details pertaining to operating instructions for the amplifier. FIBER SENSORS FX-1 The above can also be download from SUNX fiber sensor homepage ( PRO settings can be done when MODE indicator / PRO (yellow) lights up. Table for PRO mode settings FX-2 FX- NAVI mode RUN Run This indicates normal sensing operation. PRO Pro Allows various detailed settings to be configured, such as optical communications, save / load and other settings. TIMER Timer Configures operation of the timer. PRO1 PRO2 Response time change Switches among response times. Digital display setting Allows selection of different content to be viewed in the digital display. Timer setting Configures timer operation and timer period. Shift Shifts the threshold value by a certain percentage increment during limit teaching or fullauto teaching. Digital display inversion Flips and reverses the viewing orientation of the digital display. Hysteresis Allows the selection of hysteresis level. Stability Permits selection of stability indicator response levels for changes in the range for lighting up. ECO mode setting Sets the digital display to turn off automatically. Manually Set Bank Unit FX-11 FX-CH /D ON -ON / D-ON Sets output operation either ight-on, or Dark-ON. ADJ Adjust Allows fine adjustment of the threshold value. TEACH Teaching The threshold value for the FX-1(P) can be set by utilizing either 2-level teaching' or limit teaching', and the threshold value for the FX1B(P)/G(P)/H(P) can be set using these and also a third mode called full-auto teaching. PRO mode PRO PRO PRO Data bank load oads configuration setting from the data bank. Copy Using optical communications, configuration settings from the main unit are copied to connected sub units, in a single step. Coding Allows basic configuration information to be set in a single step, by inputting a -digit code. Data bank save Saves configuration setting into the data bank. Remote data bank load Using optical communications, configuration settings can be loaded from data banks, in a single step. Transmission change to permit / not to permit Allows all communication changes to be disabled during the execution of singlestep copy, load and save operations using optical communications. *Available only in FX-1B(P)/G(P)/H(P). Zero adjust Forces the numerical value for incident light intensity to, on the digital display. Remote data bank save Using optical communications, configuration settings can be saved into data banks, in a single step. Test Verifies whether optical communications have been properly established. Adjust lock Allows fine adjustment of the threshold value to be directly performed during RUN mode. Color Detection Analog Output FZ-1 FX-11A Reset All settings, except for data bank information, revert to factory settings. 9