D-Sub SEaled subminiature D connectors, 2.54 mm pitch

Size: px

Start display at page:

Download "D-Sub SEaled subminiature D connectors, 2.54 mm pitch"

Duane Robinson
6 years ago
Views:

1 SE D-Sub SEaled subminiature D connectors, 2.54 mm pitch Page Technical characteristics IP 67 versions with turned solder cups IP 67 versions with turned solder cups and rear plastic mounting plate IP 67 versions with turned solder cups and rear metal mounting plate IP 67 versions with straight turned solder pins, rear plastic mounting plate, spacer and board lock 10 IP 67 versions with angled turned solder pins, rear plastic mounting plate, bracket and board lock 12 Accessories for IP 67 connectors IP 67 plastic hoods IP 67 metallized plastic hoods Accessories for IP 67 hoods

2 sealed connectors Technical characteristics 9, 15, 25, 37, 50 UL recognized Working current 5 A Current carrying capacity The current carrying capacity is limited by maximum temperature of materials for inserts and contacts including terminals. The current capacity-curve is valid for continuous, not interrupted current-loaded contacts of connectors when simultaneous power on all contacts is given, without exceeding the maximum temperature. Control and test procedures according to DIN IEC Test voltage 1200 V/mm between 2 contacts / contact and shell Clearance and creepage 1.0 mm Contact resistance Straight contact Angled contact Angled contact 50 pole Insulation resistance between contacts 10 mω 25 mω 35 mω 5000 MΩ Working current Ambient temperature Dielectric strength 50 kv/mm Example: 25 way connector À Turned contacts Temperature range -25 O C +70 O C Contact arrangement View from termination side Protection IP 67 (per DIN / IEC 529) Termination Solder cup max. AWG 20 Solder pin straight 0.6 mm diameter Solder pin angled 0.6 mm diameter M F 9 way M F 15 way M = F = M F 25 way M F M F 37 way 50 way Material Shell Brass, tin plated over nickel Insulator and plastic watertight frame Thermoplastic, glass-fibre filled,ul 94-V0 Metal watertight frame Nickel plated zinc die cast Contact material Machined copper alloy Contact plating 0.76 µm Au min over Ni, tinned on termination area Waterproofing element Silicone Mating conditions as per DIN Mechanical Mating cycles 500 Mating force per signal contact 3.4 N Unmating force per signal contact 0.2 N 02

3 Notes 03

4 9--50 IP 67, turned solder cups No. of Identification contacts Part No. tinned metal shell with dimples Performance level S4 1) tinned metal shell ) S4: 0.76 µm Au (30 µinch)

5 9--50 IP 67, turned solder cups Identification Drawing Dimensions in mm 9 50 contacts contacts a b c d e

6 9--25 IP 67, turned solder cups, with rear plastic mounting plate No. of Identification contacts Part No. tinned metal shell with dimples Performance level S4 1) Please insert digit for flange thread 4-40 UNC þ 7 M3 þ 9 tinned metal shell Please insert digit for flange thread 4-40 UNC þ 6 M3 þ ) S4: 0.76 µm Au (30 µinch)

4-40 UNC or M3 9 25 contacts 4-40 UNC or M3 a b c d 9 40.0 25.

7 9--25 IP 67, turned solder cups, with rear plastic mounting plate Identification Drawing Dimensions in mm 9 25 contacts 4-40 UNC or M contacts 4-40 UNC or M3 a b c d

8 9--50 IP 67, turned solder cups, with rear metal mounting plate No. of Identification contacts Part No. tinned metal shell with dimples Performance level S4 1) Please insert digit for flange thread 4-40 UNC þ 7 M3 þ 9 tinned metal shell Please insert digit for flange thread 4-40 UNC þ 6 M3 þ ) S4: 0.76 µm Au (30 µinch)

contacts 9-37 50 9-37 50 4-40 UNC or M3 a b c d 9 40.0 25.00 16.4 16.9 15 48.

9 9--50 IP 67, turned solder cups, with rear metal mounting plate Identification Drawing Dimensions in mm 9 50 contacts UNC or M contacts UNC or M3 a b c d

10 9--25 IP 67, straight turned solder pins, with rear plastic mounting plate, spacer and board lock No. of Identification contacts Part No. tinned metal shell with dimples Performance level S4 1) Please insert digit for flange thread 4-40 UNC þ 7 M3 þ 9 tinned metal shell Please insert digit for flange thread 4-40 UNC þ 6 M3 þ ) S4: 0.76 µm Au (30 µinch)

Identification Drawing Dimensions in mm 9 25

a b c d g h i 9 40.0 25.00 16.4 16.9 4 x 2.74 = 10.

2 7 x 2.74 = 19.18 6 x 2.74 = 16.44 33.3 25 62.0 47.

11 9--25 IP 67, straight turned solder pins, with rear plastic mounting plate, spacer and board lock Identification Drawing Dimensions in mm 9 25 contacts 4-40 UNC or M contacts 4-40 UNC or M3 a b c d g h i x 2.74 = x 2.74 = x 2.74 = x 2.74 = x 2.76 = x 2.76 = Board drillings 11

12 9--25 IP 67, angled turned solder pins, with rear plastic mounting plate, bracket and board lock No. of Identification contacts Part No. tinned metal shell with dimples Performance level S4 1) Please insert digit for flange thread 4-40 UNC þ 7 M3 þ 9 tinned metal shell Please insert digit for flange thread 4-40 UNC þ 6 M3 þ ) S4: 0.76 µm Au (30 µinch)

M3 a b c d g h i 9 40.0 25.00 16.4 16.9 4 x 2.

7 25.2 7 x 2.74 = 19.18 6 x 2.74 = 16.44 33.3 25 62.

13 9--25 IP 67, angled turned solder pins, with rear plastic mounting plate, bracket and board lock Identification Drawing Dimensions in mm 9 25 contacts 4-40 UNC or M contacts 4-40 UNC or M3 a b c d g h i x 2.74 = x 2.74 = x 2.74 = x 2.74 = x 2.76 = x 2.76 = Board drillings 13

14 Accessories for IP 67 connectors No. of Identification contacts Part No. Drawing Dimensions in mm Front sealing rubber IP x Female screw lock M3 (length of engagement) Tin plated Female screw lock 4-40 UNC UNC 2B (length of engagement) Tin plated 4-40 UNC 2A 14

caps Mounting instructions The stripped braid should not be fold back to avoid damaging the cable clamp and reducing its performance.

15 IP 67 plastic hoods No. of Identification contacts Part No. Drawing Dimensions in mm Hood Black thermoplastic shell screw Hood cap Hood Holding caps Mounting instructions The stripped braid should not be fold back to avoid damaging the cable clamp and reducing its performance. cable clamp cable clamp screw Rubber gasket O-ring seal Holding frame a b c d e f g h

16 IP 67 metallized plastic hoods No. of Identification contacts Part No. Drawing Dimensions in mm Hood Metallized thermoplastic shell screw Hood cap Hood Holding caps Mounting instructions The stripped braid should not be fold back to avoid damaging the cable clamp and reducing its performance. cable clamp cable clamp screw Rubber gasket shielding plate Holding frame O-ring seal 16 a b c d e f g h

17 Accessories for IP 67 hoods No. of Identification contacts Part No. Drawing Dimensions in mm Short locking screw 4-40 UNC Brass, Nickel plated Short locking screw M3 UNC 4-40 or M Knurled locking screw 4-40 UNC Brass, Nickel plated knurl DIN 82, RAA 0.5 Knurled locking screw M3 UNC 4-40 or M Knurled locking screw 4-40 UNC with plastic cap UNC 4-40 or M3 Brass, Nickel plated Polyester (max. 130 C), black Knurled locking screw M3 with plastic cap

18 18 Notes

Directory chapter 05. D-Sub Filter subminiature D connectors, 2.54 mm pitch

Directory chapter 05. D-Sub Filter subminiature D connectors, 2.54 mm pitch F Directory chapter 05 D-Sub Filter subminiature D connectors, 2.54 mm pitch New Page General information.............................................. 05.02 Technical characteristics..........................................