Electrical Components Catalog Universal MATE-N-LOK Connector System
|
|
- Kerry Bruce
- 6 years ago
- Views:
Transcription
1 Introduction Product Facts Pins and sockets can be intermixed in the same housing Positive polarization Rear cavity identification Contacts completely enclosed in housings Positive locking housings Insulation capability to 5.1 mm diameter Removable, crimp snap-in contacts Low contact mating force Contacts accept WG mm2 wire sizes Contacts available with pre-tin or gold plating Dual locking lances provide optimum contact stability Panel mount or free hanging Mate with Universal MTE-N- LOK II Housings vailable in UL 94 V-0 and V-2 flame retardant material. Meets the material requirements of table 25.1 of UL Standard 1410 (television receivers and video products) Not for interrupting current Harness to PC Board capability using pin or socket headers Pin and socket headers are available in both vertical and right-angle style Solderability: Headers meet MIL-STD 202 Method 208 Contacts are on 6.35 mm centerline spacing Recognized under the Component Program of Underwriters Laboratories, Inc., File No. E28476 Certified by Canadian Standards ssociation, File No. LR7189 Passed test by VDE under their Registration Number 3980/ Continuous Surveillance R R Technical Features vailable Number of Positions 1 15 Centerline Spacing 6.35 mm Housing Material Polyamide Flammability Rating acc. UL 94 V-0 and V-2 Contact Material Phosphor Bronze, Brass Contact Finish Tin or Duplex Gold Plated Wire Size mm 2 ; WG Insulation up to 5.1 mm Diameter Temperature 55 C up to +125 C Voltage Rating 600 V C or DC Current Rating up to 19 Termination Resistance max. 3.5 mω Connector Mating per Circuit max N (Split Pin) pprovals VDE, UL, CS Product Specifications Connectors: PC Board Headers: pplication Specification Instruction Sheet Housings, Contacts and ccessories ll specifications subject to change. Consult Tyco Electronics for latest specifications. 12-1
2 Technical Features Technical Documents Product Specifications: for Connectors for PC Board Headers pplication Specification: for Contacts Plug, Cap, Headers, Pin, Socket and ccessories Performance Characteristics The Universal MTE-N-LOK Connector performance characteristics found on page 12-3 are based on free hanging and panel mount connectors, loaded with contacts crimped on stranded wire. Dielectric Withstanding Voltage: 5.0 kv C or 10.0 kv DC between adjacent circuits (initially) Insulation Resistance: 1000 megohms minimum between adjacent circuits Voltage Ratings: 600 V C or DC (UL) 400 V C or DC (VDE) Connector Mating: Solid Pin: 6.7 N max. per circuit Split Pin: 13.4 N max. per circuit Connector Unmating: Solid Pin: 2.25 N min. per circuit Split Pin: 3.1 N min. per circuit Contact Insertion Force: 22.2 N max. per contact Contact Retention: 66.7 N min. per contact Durability: 50 cycles, mating and unmating Maximum Current The maximum current rating of Universal MTE-N-LOK connectors is limited by the maximum operating temperature of the housings which is +125 C for UL 94 V-2 housings and +125 C for UL 94 V-0 housings including the temperature rise of the contacts which is a maximum of 30 C. There are several variables which have a direct effect on this max. currentcarrying capability for a given connector and must be considered for each application. These variables are: Wire Size Larger diameter wire will carry more current since it has less in-ternal resistance to current flow and thus generates less heat. Longer wire lengths also enhance current carrying capabilities since the wire conducts heat away from the connector. Connector Size In general, the more circuits in a connector, the less current can be carried. mbient Temperature The higher the ambient temperature, the less current can be carried in any given connector. Printed Wiring Board Conductor Size The finished trace conductor width and thickness should be maximized to allow for the greatest current carrying capacity and heat dissipation. The Universal MTE-N-LOK connectors also will withstand the following tests: Vibration: cycles per minute at 1.5 mm total excursion Physical Shock: 18 drops, 50 g sawtooth at 10 milliseconds Housing Panel Retention: 334 N min. Housing Lock Strength: N min. Temperature : 55 C to +125 C Thermal Shock: 55 C to +85 C Temperature-Humidity Cycling: +25 C to +65 C at 95 % Relative Humidity Corrosion: 48 hours at 5% salt concentration Minimum Wire Lengths for Temperature Rise vs. Current Testing Wire Size (WG) (mm 2 ) Wire Length , Note: If wire lengths used are less than those listed above, the current carrying ability of the system will be reduced due to less heat being conducted away from the connector. The customer should fully test all applications ll specifications subject to change. Consult Tyco Electronics for latest specifications.
3 Technical Features (continued) Current Rating Verification for 30 C max. Temperature Rise, 100 % Energized Wire-to-Wire Values are based on initial Temperature Rise versus Current Testing and are intended to be a guide in the selection of a connector family. ll applications should be tested by the end user. The values listed are per circuit for fully loaded housings being 100% energized. Universal MTE-N-LOK Calculated Current Table () No. of Circuits Wire Size WG (mm 2 ) In-Line Matrix Note: ll combinations were not tested, and this chart contains interpolated and extrapolated values. Wire-to-Board Due to the vast differences in trace geometry and printed circuit board configurations, we are unable to provide a separate current carrying chart for our printed circuit board header products. However, the above Wire-to-Wire charts may be used as a guideline for headers if the trace width and thickness is equal to the listed wire gauge. For vertical headers, only 75 % of the Wire-to-Wire value should be used. The chart values are only a tool for connector selection and will require the customer to fully test their application. Termination Resistance/ Contact Crimp Tensile Force Wire Size (WG) (mm 2 ) Termination Resistance Test Current Resistance () (mω) Contact Crimp Tensile Force (N) ) Note: This is the total resistance between wire crimps of a mated pin and socket. ll specifications subject to change. Consult Tyco Electronics for latest specifications. 12-3
4 Connector Mating Combinations 1 Connector Part Number No. of Circuits Flammability Rating UL 94 V-2 UL 94 V-0 Style Plug 1) Cap 1) ) ) ) ) Plating Standard Mating Connector Part Numbers PC Board Headers 1) Vertical Pin Vertical Socket Right-ngle Standard Polarized Long Standard Standard Polarized Long Pin Socket 2 pre-tinned UL 94 V-2 In-Line ) Duplex ) pre-tinned UL 94 V-0 In-Line ) ) Duplex UL 94 V-2 UL 94 V-0 5) pre-tinned ) In-Line ) Duplex pre-tinned ) )9 In-Line ) Duplex pre-tinned UL 94 V-2 In-Line ) Duplex pre-tinned UL 94 V-0 In-Line 5) ) Duplex UL 94 V-2 In-Line UL 94 V-0 In-Line pre-tinned ) ) Duplex pre-tinned ) ) Duplex UL 94 V-2 In-Line pre-tinned ) ) Duplex UL 94 V-0 In-Line UL 94 V-2 Matrix ) pre-tinned ) ) Duplex ) pre-tinned ) Duplex UL 94 V-0 Matrix pre-tinned ) 5) ) Duplex For Higher Housing Positions and Notes: See Page ll specifications subject to change. Consult Tyco Electronics for latest specifications.
5 UL 94 V-2 In-Line ) Duplex UL 94 V-0 In-Line ) Duplex Electrical Components Catalog Connector Mating Combinations (continued) Connector Part Number Mating Connector Part Numbers PC Board Headers 1) No. of Circuits Flammability Rating Style Plug 1) Cap 1) Plating Standard Vertical Pin Vertical Socket Right-ngle Standard Polarized Long Standard Standard Polarized Long Pin Socket 8 5) pre-tinned UL 94 V-2 In-Line ) Duplex ) pre-tinned UL 94 V-0 In-Line ) Duplex ) pre-tinned UL 94 V-2 Matrix ) Duplex ) pre-tinned )9 UL 94 V-0 Matrix ) Duplex pre-tinned pre-tinned ) pre-tinned UL 94 V-2 Matrix ) Duplex ) pre-tinned UL 94 V-0 Matrix ) ) Duplex ) pre-tinned UL 94 V-2 Matrix ) Duplex ) pre-tinned UL 94 V-0 Matrix ) Duplex ) Universal MTE-N-LOK Plug and Cap housings accept pin or socket contacts. Use the appropriate contacts in the Plug housing as required by the mating component, shown on page 12-6 and Duplex Finish: Plated with 0.76 µm min. gold in mating area, matte tin-lead on solder tail end over 1.27 µm min. nickel underplate on entire contact. 3) Black in color. 4) Tool Removable. 5) Latches for visual locking check. Note: Standard for use with PC Board thickness 1.57 mm. ll specifications subject to change. Consult Tyco Electronics for latest specifications. 12-5
6 Pin Contacts Pin: 2.13 mm diameter in mating area Split Pin: 2.18 mm diameter in mating area Housings: Page These contacts can be used in either Universal MTE-N-LOK Plug or Cap housings only. Wire Size (mm 2 ) Insulation Diameter Dimension L Pin Brass, pre-tinned ,000 Phosphor Bronze, Gold ,000 Brass, pre-tinned ,000 Brass, Gold , ) Brass, Select Gold 3) , ) Phosphor Bronze, pre-tinned ,000 Phos. Bronze, Select Gold 3) ,000 Brass, pre-tinned ,000 Phosphor Bronze, pre-tinned ,000 (Split Pin) Brass, Select Gold 3) ,000 Phos. Bronze, Select Gold 3) ,000 Brass, pre-tinned ,000 Brass, Gold , Brass, Select Gold 3) ,000 Phosphor Bronze, pre-tinned Phos. Bronze, Select Gold 3) ,000 Brass, pre-tinned ,000 Brass, Gold , Phosphor Bronze, pre-tinned ,000 L Material and Finish Part Numbers Loose- Piece (Split Pin) Phos. Bronze, Select Gold 3) ,000 Part Number Hand Tool ) ) ) ) ) Brass, Select Gold 3) ,000 Brass, pre-tinned ,000 Brass, Gold , Brass, Select Gold 3) ,000 Phosphor Bronze, pre-tinned ,000 Phos. Bronze, Select Gold 3) ,000 Brass, pre-tinned , Brass, Gold ,000 (Split Pin) Brass, Select Gold 3) , ) ) ) ) Brass, pre-tinned 4) ) , ) Phosphor Bronze, pre-tinned , ) Brass, pre-tinned , Phosphor Bronze, pre-tinned , ) Phosphor Bronze, Gold ,000 Brass, Gold ,000 Brass, pre-tinned , max ) 20.6 Phosphor Bronze, pre-tinned , ) (Split Pin) Brass, Select Gold 3) ,000 Phosphor Bronze, pre-tinned , max ) 20.1 Brass, Select Gold 3) , ) Phosphor Bronze, Gold ) Split Pins for use with housings >6 positions to reduce engaging force. Plain Versions upon request ll specifications subject to change. Consult Tyco Electronics for latest specifications.
7 Socket Contacts These contacts can be used in either Universal MTE-N-LOK Plug or Cap housings only. Housings: Page L Wire Size (mm 2 ) Insulation Diameter Dimension L Socket Material and Finish Part Numbers Loose- Piece Brass, pre-tinned Phosphor Bronze, Gold Brass, pre-tinned Brass, Select Gold 3) Phosphor Bronze, pre-tinned Phos. Bronze, Select Gold 3) Brass, pre-tinned Brass, Gold Brass, Select Gold 3) Phosphor Bronze, pre-tinned Phos. Bronze, Select Gold 3) Brass, pre-tinned Brass, Gold Brass, Select Gold 3) Phosphor Bronze, pre-tinned Phos. Bronze, Select Gold 3) Part Number Hand Tool ) ) ) ) ) ) ) Brass, pre-tinned ) Phosphor Bronze, pre-tinned Brass, pre-tinned Phosphor Bronze, pre-tinned Phosphor Bronze, Gold Brass, Gold Phosphor Bronze, pre-tinned ) ) max ) 19.8 Brass, Select Gold 3) ) Phosphor Bronze, Gold Plain Versions upon request. Notes: 1) There is no insulation barrel on this contact. Insulation maximum diameter is limited by the housing cavity diameter µm Gold finish in mating area and inside wire barrel over 1.27 µm nickel underplate on entire contact. 3) 0.76 µm Gold finish in mating area, 1.27 µm tin plating inside wire barrel over 1.27 µm nickel underplate on entire contact. 4) Recommended for predominant use of 2.0 mm 2 wire size 5) Die Set for ERGOCRIMP Basic Hand Tool, Part No dapter for ERGOCRIMP Die Sets: Part No for pneumatic tool 626 system 6) Hand Tool, Part No for wire size mm 2 Hand Tool, Part No for wire size mm 2 Hand Tool, Part No with Die Set for wire size 3.0 mm 2 Hand Tool, Part No with Die Set for wire size 5.0 mm Electric Crimp Unit: 2 Part No Pneumatic Tool: Part No Die Set for mm 2 : Part No Die Set for mm 2 : Part No Tool Holder: Part No Contact Insertion Tool for wire sizes, 0.5 mm 2, Part No Note: Use Phosphor Bronze contacts for use with higher temperature and changing from moist to dry condition. ll specifications subject to change. Consult Tyco Electronics for latest specifications. 12-7
8 ccessories Grounding Pin (Mate first, Break last, not for interrupting current) 2.54 mm longer than standard pin. These contacts can be used in either Universal MTE-N-LOK Plug or Cap housings only. Wire Size (mm 2 ) (WG) Insulation Diameter Dimension L L Material and Finish Contact Part Numbers Loose- Piece Part Number Brass, pre-tin plated Brass, pre-tin plated , ** max.* 23.1 Phosphor Bronze, pre-tin plated Hand Tool ** There is no insulation barrel on this contact. Insulation maximum diameter is limited by the housing cavity. ** Die Set for ERGOCRIMP Basic Hand Tool, Part No Programmable Connector Contact Socket with 2.8 mm Series Special FSTON Tab (i.e. Part No ) Material and Finish: Brass, pre-tin plated Part No : 1, Contact Extraction Tool Part No Spare Tube: Part No Contact Insertion Tool Part No ll specifications subject to change. Consult Tyco Electronics for latest specifications.
9 Housings Housings, Free Hanging or Panel Mount, 6.35 mm Centerline 1 Circuit, Free-Hanging Plug Cap Part Numbers: See Table on Page Related Product Data Product Specification: for Connectors Performance Characteristics: Page 12-3 Contacts: Page 12-6 thru 12-8 Panel Cutout Recommendations: Page Keying Plug: Page Strain Reliefs: Page and Technical Documents: Page 12-2 Mating Headers: Page 12-4 and , 3, 4, 5, 6, 8 and 10 Circuit, In-Line Plug Circuit, Matrix Plug Detail See Page Detail See Page Cap Cap , 12 and 15 Circuit, Matrix Plug Detail See Page Cap ll specifications subject to change. Consult Tyco Electronics for latest specifications. 12-9
10 Housings (continued) 9, 12 and 15 Circuit, Matrix (continued) Detail 1 Detail 2 Detail 1 Solid locking latches, flat outer surface (Robust design) Detail 2 Latches with stepped outer surface and Window feature for locking inspection Parts with Window latches are marked in the table with. No. of Circuits Dimension Plug Polyamide acc. UL 94 V-2, Natural Color Cap Housing Part Numbers Plug Polyamide acc. UL 94 V-0 Cap , , ) ) 4, ) ) 2, ) * ) ) ) ) 3, * * 1) , ) ) ) ) 1, * 1) , ) ) ) ) 1, ) 1) 3) * * , * 1) ) 1, ) ) 1, ) 3) * * ) 1,200 2, * ) ) ) ) ) * 1) * 1) 3) ,200 1, * * ) 3) * ) 1) 3) * ) * * * * 1) In-Line style. Housing material has +125 C temperature rating. 3) Without flanges for strain reliefs. 4) Tool-Removable ll specifications subject to change. Consult Tyco Electronics for latest specifications.
11 Recommenden Panel Cutout Cap Housing View is from Cap Entry Side D B Please refer to pplication Specification: Note Note 1: Circuit Number 1 location when using panel keying with 2, 3, 4, 5, 6, 8 and 10 circuit In-Line housings. Note 2: Optional: Do not remove this material E when keying cap housing to panel C E 2.8 Coded D B D B Uncoded Note 1 Note E 2.54 E C 2.8 C 2.8 Remarks: 1. Recommended panel thickness 0.8 mm up to 2.3 mm. Panel must be punched so that housing enters panel in same direction as the punch mm dimension is 3.18 mm for 6, 8 and 10 circuit In-Line housings. Style No. of Circuits Dimensions B C D E In-Line Matrix ll specifications subject to change. Consult Tyco Electronics for latest specifications
12 Strain Reliefs Keying Plug Part No : 500 Material: Polyamide, UL 94 V-2 Part No : 500 Material: Polyamide, UL 94 V Note: The keying plug locks into plug and cap housing cavities. Plug Housing Strain Reliefs Related Product Data Plug Housings: Page Technical Documents: Page 12-2 Part No : 500 Material: Polyamide, UL 94 V-2 Part No : 500 Material: Polyamide, UL 94 V-0 2, 3, 4, 5, 6 and 8 Circuit, In-Line Wire Bundle Diameter 8.0 mm max , 9, 12 and 15 Circuit, In-Line 1 Wire Bundle Diameter 12.7 mm max. Part No : 500 Material: Polyamide, UL 94 V-2 Part No : 500 Material: Polyamide, UL 94 V Strain relief part number represents one half of a strain relief. Two strain reliefs required per housing. 2 Two pan head sheet metal screws acc. DIN 7971 (not supplied!) 3.5 mm diameter x 16.0 mm ll specifications subject to change. Consult Tyco Electronics for latest specifications.
13 Strain Reliefs (continued) Plug or Cap Housing Strain Reliefs Related Product Data Housings: Page Technical Documents: Page , 3, 4, 5, 6, 8, 9, 12 and 15 Circuits (Enclosed) Note 4 Cap Housing 1 Two pan head sheet metal screws according DIN x 9.5 mm (not supplied!) Note 3 In-Line 1 Matrix Note 3 Note Note Note 2 1 Insert, Note 1 Style In-Line Matrix No. of Circuits Dimension Insert Supplied Single Wire Diameter Wire Bundle Diameter Part Numbers Polyamide Polyamide UL 94 V-2 UL 94 V-0 Natural Notes: 1. Cable clamping insert comes attached to strain relief. It can be used to provide additional adjustment for small wire bundles or discarded. 2. Insert to be positioned as shown by dotted lines. 3. Strain relief part number represents one-half of a strain relief. Two strain reliefs required per housing. 4. Must use cap housing adapters when attaching strain reliefs to a cap housing. Two adapters required per housing (see page 12-14). 5. Strain reliefs for 6 and 8 position In-Line fits plug housings only. White Yes No Yes No Yes No Yes No Yes Note No Yes Note No Yes Yes Yes Yes ll specifications subject to change. Consult Tyco Electronics for latest specifications
14 ccessories for Strain Reliefs Cap Housing dapters These adapters are designed to anchor the cap housing strain reliefs to the housings and prevent the strain relief halves from drawing in when the screws are being torqued down to clamp the cable. For ll Positions, Except 2, 6 and 8 Circuit Cap Housings Part No : 500 Material: Polyamide, natural color, acc. UL 94 V-2 Part No : 500 Material: Polyamide, white, acc. UL 94 V-0 For 2 Circuit In-Line and 6 Circuit Matrix Cap Housings only Part No : 500 Material: Polyamide, natural color, acc. UL 94 V-2 Part No : 500 Material: Polyamide, white, acc. UL 94 V ll specifications subject to change. Consult Tyco Electronics for latest specifications.
15 Sealed Connector System Plug Housing Mating End Wire Seal Contact Cavity Cap Housing Wire Seal Interface Seal Pin Contact Silos Back Side (Wire-End) Sealing Plug For proper use of this product, customer should make sure that the Instruction Sheet is available for review. Product Facts Economical splash proof/ immersible sealed connector system. No design changes to existing Universal MTE-N-LOK product. Existing applications utilizing Universal MTE-N-LOK can be upgraded to a splash proof system. Utilizes two wire seals and one interface seal. Wire size range mm2 with insulation diameter range mm mm insulation diameter passed European IP sealing level 57 (swirling dust/immersion to 1 meter for 30 minutes) mm insulation diameter passed European IP sealing level #56 (swirling dust/heavy seas). Universal MTE-N-LOK II keying plug can be used to seal unused circuits. ll specifications subject to change. Consult Tyco Electronics for latest specifications
16 Sealing Components Material: Silicone rubber, blue color 2, 3, and 4 Circuit, In-Line 7.6 Technical Documents Product Specification: Splash Proof Seal, Connectors Contacts: Page and Page Housings: Page Splash Proof Seals 6 Circuit, Matrix Wire Seal Interface Seal Wire Seal Interface Seal 9, 12, and 15 Circuit, Matrix Wire Seal Interface Seal No. of Circuits Dimension Interface Seal Part Numbers Wire Seal Note: One interface seal and two wire seals required per mated assembly ll specifications subject to change. Consult Tyco Electronics for latest specifications.
17 Pin Contacts Used with Splash Proof Seals These contacts can be used in either Plug or Cap housings only. Solid Pin: Diameter 2.13 mm Split Pin: Diameter 2.18 mm Splash Proof Seals Pin Split Pin L Related Product Data Product Specification: for Connectors pplication Specification: for Contacts Performance Characteristics: Page 12-2 Housings: Page 12-9 and Page Grounding Pin L L 2.54 mm longer than standard pin. (Mate first, break last, not for interrupting current) Wire Size (mm 2 ) Insulation Diameter Dimension L Pin Material and Finish Contact Part Numbers Pin Loose Piece Part Number Hand Tool Brass, pre-tinned 1) Brass, Gold Brass, Selective Gold 3) Phosphor Bronze, pre-tinned 3) Phosphor Bronze, Selective Gold 3) Brass, pre-tinned 1) Brass, Gold ) ) Phosphor Bronze, pre-tinned 1) (Split Pin) Copper Iron, plain ) (Grounding Pin) Copper Iron, pre-tinned 1) Phosphor Bronze, Selective Gold 3) Brass, Selective Gold 3) Brass, pre-tinned 1) ) 1) 2 6 µm tin plated. 0.8 µm gold over 1.3 µm nickel inside crimp and contact area, entire contact with 1.3 µm nickel plating. 3) 2 6 µm gold over nickel in contact area. 4) Die Set for ERGOCRIMP Basic Hand Tool, Part No Notes: 1. MP recommends split pins be used in housings having 6, 9, 12 and 15 circuits to reduce mating force. 2. Phosphor bronze material contacts are available for use in high temperature/humidity cycling applications, consult Tyco Electronics. 3. WG ( mm 2 ) contacts, shown on page 12-4 and 12-5, can be used with splash proof seals if insulation diameter range is 1.5 mm and 2.5 mm. ll specifications subject to change. Consult Tyco Electronics for latest specifications
18 Socket Contacts Used with Splash Proof Seals These contacts can be used in either Plug or Cap housings only. Related Product Data Product Specification: for Connectors pplication Specification: for Contacts Performance Characteristics: Page 12-2 Housings: Page 12-9 and Page Splash Proof Seals (continued) Solid Socket L Wire Size (mm 2 ) Insulation Diameter Dimension L Pin Material and Finish Contact Part Numbers Socket Loose Piece Part Number Hand Tool Brass, pre-tinned 1) Brass, Gold Brass, Selective Gold 3) Phosphor Bronze, pre-tinned 3) ) ) Phosphor Bronze, Selective Gold 3) ) 2 6 µm tin plated. 0.8 µm gold over 1.3 µm nickel inside crimp and contact area, entire contact with 1.3 µm nickel plating. 3) 2 6 µm gold over nickel in contact area. 4) Die Set for ERGOCRIMP Basic Hand Tool, Part No Notes: 1. MP recommends split pins be used in housings having 6, 9, 12 and 15 circuits to reduce mating force. 2. Phosphor bronze material contacts are available for use in high temperature/humidity cycling applications, consult Tyco Electronics. 3. WG ( mm 2 ) contacts, shown on page 12-4 and 12-5, can be used with splash proof seals if insulation diameter range is 1.5 mm and 2.5 mm ll specifications subject to change. Consult Tyco Electronics for latest specifications.
19 ccessories Sealing Plug Part No : 1, Material: Polyamide Flammability Rating: UL 94 V Seal Latch Tool Part No Contact Extraction Tool Part No Spare Tube: Part No Contact Insertion Tool (For Inserting Contacts applied to Small Diameter Wire) Part No ll specifications subject to change. Consult Tyco Electronics for latest specifications
20 Test Connectors (with Spring Loaded Contacts) Housing Material: Polyamide Flammability Rating: UL 94 V-0 Test Connectors 2, 3, 4, and 5 Circuit, In-Line Plug Cap Related Product Data Mating Connectors: Housings and headers having the same number of circuits. The housings can have pin or socket contacts, or also a combination of both. Mating Housings: Page Mating Headers: Page 12-4 and Page , 9, 12 and 15 Circuit, Matrix Plug 1 Cap mm Diameter Pin Mates with Universal MTE-N-LOK Sockets No. of Circuits Plug Kit Part Numbers Notes: 1. Test probes have 5 max. current rating. 1,000,000 cycles. 2. Test Connector housings are of the same configuration as standard housings. Refer to Page for dimensional specifications. Cap ll specifications subject to change. Consult Tyco Electronics for latest specifications.
Universal MATE-N-LOK Connectors
Product Facts Pins and sockets can be intermixed in the same housing Positive polarisation Rear cavity identification Contacts completely enclosed in housings Positive locking housings Insulation capability
More informationDistributed by: www.jameco.com -800-8-44 The content and copyrights of the attached material are the property of its owner. Pin and Socket Mini-Universal MTE-N-LOK Product Facts Compact, durable housings
More informationMini-Universal MATE-N-LOK Connectors
MP Mini-Universal MTE-N-LOK Product Facts Compact, durable housings Pins and sockets can be accommodated in the same housings Contacts fully protected in the housings. Both pins and sockets can be used
More informationMini-Universal MATE-N-LOK Connectors
MP Mini-Universal MTE-N-LOK Product Facts Compact, durable housings Pins and sockets can be accommodated in the same housings Contacts fully protected in the housings. Both pins and sockets can be used
More informationMini-Universal MATE-N-LOK Connectors
MP Mini-Universal MTE-N-LOK Product Facts Compact, durable housings Pins and sockets can be accommodated in the same housings Contacts fully protected in the housings. Both pins and sockets can be used
More information(MR) Miniature Rectangular Connectors (Continued)
Product Facts Housings positively lock to help prevent accidental disengagement Either cap or plug housing can be mounted in same rectangular panel cutout without additional hardware UL94V-0 housings Plug
More informationCommercial MATE-N-LOK Connectors
MP Commercial MTE-N-LOK Connectors Product Facts Fully polarized nylon housings Easy cavity identification Locking devices are integral part of design. Connector halves will hold together under severe
More informationMini-Universal MATE-N-LOK 2 Connectors
MP Mini-Universal MTE-N-LOK 2 Product Facts One molded piece, secondary locking plug and cap housing assemblies Three-point stabilization to provide better terminal position Fully polarized to provide
More information.093 Commercial Pin and Socket Connectors
Product Facts Polarised Cavity identification Low contact-mating force Dual locking lances Detent and positive locking Contacts available in brass and phosphor bronze with tin and gold plating Panel-mounting
More informationMTA-156 IDC Quad Connectors
MT-156 IDC Quad Connectors MT-156 Product Facts Provides four points of contact Greater current carrying capability than Standard MT-156 Connectors Connector styles include both closed end and feedthru
More informationAMP Soft Shell Pin and Socket Connectors
Soft Shell Pin and Socket Connectors Restriction on the use of Hazardous Substances (RoHS) t Tyco Electronics, we re ready to support your RoHS requirements. We ve assessed more than 1.5 million end items/components
More informationIntroduction to High Current Card Edge Connectors
Introduction to High Current Card Edge Connectors Product Facts Contacts on.100 [2.54] Centerlines Selective gold plating of contacts for high performance at low cost Flow solder applications Glass-filled
More informationAMPMODU System 50 Connectors
AMPMODU System 50 Connectors (Page 52) (Page 44) (Page 8) (Page 40) (Page 45) (Page 9) (Page 1) (Page 29) AMPMODU System 50 (Page 4) (Page 0) (Page ) (Page 50) Double Row,.025 Ribbon Cable Mount Receptacle
More informationUniversal MATE-N-LOK Headers for UMNL II Connectors
for UMNL II Connectors PC Board Vertical Pin Headers [6.5] Centerline spacing,, and 5 Circuit, In-Line Housing Nylon Flammability ating UL9V-0 Contacts Phosphor bronze Solder tail diameter.06 [1.57] elated
More informationThe con ectors serve low durability cycle applications
Power Connectors & Interconnection Systems Introduction to High Current Card Edge Connectors Product Facts Contacts on.100 [2.54] Centerlines Selective gold plating of contacts for high performance at
More informationIntroduction. The information pages provide standard data common to all D-subminiature connectors. These include:
Connectors Information Introduction The D-subminiature is one of the most popular styles of connectors in the I/O category. It is used in computer, telecom, datacom, medical, and test instrumentation applications
More informationElcon CROWN EDGE Card Edge-style High Current Connectors
Elcon CROWN EDGE Card Edge-style High Current Connectors CROWN EDGE is a board-to-board power interconnect solution that uses Elcon high performance Crown contact technology configured to mate directly
More informationAMP Drawer Series Connectors Miniature Power Drawer (MPD) Connectors
Miniature Power Drawer (MPD) Connectors Product Facts High mating cycle life Low Mating and Un-mating force (< 0.2lbs per contact) Single-piece molded housing Molded-in guide pins provide generous blind-mateability
More informationRECTANGULAR POWER CONNECTORS
TE Connectivity: Every Connection Counts 2015 TE Connectivity Ltd. family of companies. All Rights Reserved TE CONNECTIVITY (TE) 08P MTA156 CONN ASSY 3-643818-8 TE Internal Number: 3-643818-8 Product Type
More informationPRODUCT SPECIFICATION. This specification defines the detailed requirements for the Minitek Pwr3.0 wire to wire and wire to board connectors.
s-12-1177*1.0 SCOPE 1 of 8 D This specification defines the detailed requirements for the Minitek Pwr3.0 wire to wire and wire to board connectors. 2.0 APPLICABLE DOCUMENTS The following documents, of
More information.050" IDC Connectors for.025" Ribbon Cable - M73 Series
.050" IDC Connectors for.025" Ribbon Cable - M73 Series PRT NUMER LEGEND M73X-XXXX-XX STYLE 01 = Low profile.050" IDC Socket for single layer.025" Flat Cable 02 = Standard profile IDC Socket for single
More informationMetrimate Pin and Socket Connectors. Table of Contents
Product Facts Recognized under the Component Program of U n d e rwriters Laboratories Inc., File No. E28476 Certified by Canadian Standards Association, File No. LR7189 Tested to VDE requirements outlined
More informationD-Sub SEaled subminiature D connectors, 2.54 mm pitch
SE D-Sub SEaled subminiature D connectors, 2.54 mm pitch Page Technical characteristics.......................................... 02 IP 67 versions with turned solder cups......... 04 IP 67 versions with
More informationAMPMODU Interconnection System
AMPMODU Interconnection System PC/104 and PC/104- Plus Connectors.00 x.00 [1.27 x 1.27] Centerline.00 x [1.27 x 2.4] Centerline AMPMODU 2mm Connectors x [2.4 x 2.4] Centerline.12 x.12 [3.18 x 3.18] Centerline.16
More informationAMPMODU* MOD I Interconnection System
Product Specification AMPMODU* MOD I Interconnection System 03 JUN 2013 Rev E All Paragraphs Revised 1. SCOPE This specification covers performance and test requirements for the AMPMODU MOD I Interconnection
More informationProduct Specifications (for connectors), and (for headers), provides product performance requirements and test result information.
This specification covers the requirements for application of Universal MATE N LOK Housings, Contacts, and Printed Circuit (PC) Board Headers. The housings are available in 1 through 15 circuit versions
More informationDUBOX SHUNTS BOARD/WIRE-TO-BOARD CONNECTORS FEATURES & BENEFITS. Dual-beam contacts for added reliability
BOARD/WIRE-TO-BOARD CONNECTORS DUBOX SHUNTS FEATURES & BENEFITS Dual-beam contacts for added reliability Slotted cutout in low profile housing simplifies electrical testing Side-by-side and end-to-end
More informationRX CONNECTOR. Features. Standards. Disconnectable Insulation displacement connectors for 1.27mm pitch ribbon cables. 2.54mm
RX CONNECOR mm Disconnectable Insulation displacement connectors for.27mm pitch ribbon cables pitch Features Conforms to MIL Standards s RX connectors conform to MIL standards (MIL-C-833) and are compatible
More informationRIBBON CABLE CONNECTORS
TE Connectivity: Every Connection Counts 2015 TE Connectivity Ltd. family of companies. All Rights Reserved CONNECTORS RIBBON CABLE CONNECTORS TE CONNECTIVITY (TE) A/L UNIV HDR 14P VERT AMP-LATCH Universal
More informationRIBBON CABLE CONNECTORS
TE Connectivity: Every Connection Counts 2015 TE Connectivity Ltd. family of companies. All Rights Reserved CONNECTORS RIBBON CABLE CONNECTORS TE CONNECTIVITY (TE) 20 NOVO MIL/CTR 15DP,LEAD FREE 1658621-4
More informationCROWN CLIP Series Sockets
OWN LIP Series Sockets Product Facts ompact design High performance OWN BND contacts urrents to 350 mps 1 Mates with solid or laminated blades Supports true hot-plug (current interruption)2 Float-mount
More informationCROWN LINE Power Bus Bar Distribution System
COWN LINE Power Bus Bar Distribution System COWN LINE Power Bus Bar Distribution System The pluggable bus bar system Currents up to 300 Amps Up to 2 meters in length Pluggable breakers VDE finger proof
More informationMating Interfaces 1,63 (.064) 3,45 (.135) Ø3,71 (.146) MAX Ø6,61 (.260) MAX Ø3,71 (.146) MAX
SMB / SMC Cannon's SMB Snap-on and SMC Screw-on subminiature coaxial connectors have been specifically engineered for high performance and high reliability applications in both military and commercial
More informationCannon 50 Ohm Connectors
SMB / SMC Cannon's SMB Snap-on and SMC Screw-on subminiature coaxial connectors have been specifically engineered for high performance and high reliability applications in both military and commercial
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. Power Connectors FEATURES AND SPECIFICATIONS Features and Benefits Positive
More informationPRODUCT SPECIFICATION
SINGLE ROW CONNECTOR SYSTEM 1.0 SCOPE This Product Specification covers the 3.00 mm (.118 inch) centerline (pitch) square pin headers when mated with either printed circuit board (PCB) connector or connectors
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. C 2.54mm (.100") Pitch FEATURES AND SPECIFICATIONS Features and Benefits
More informationD-3100S Standard 1-Row Type
(Wire-to-Board, Wire-to-Panel and Wire-to-Wire) List of Products by Application Used for both signal circuit and power/power supply circuit applications. Able to carry 15A max. of current per position
More informationCMC CP Terminals CP 0.635mm (.025 ) CP 1.50mm (.059 ) CP 2.80mm (.110 ) FEATURES AND SPECIFICATIONS
FEATURES AND SPECIFICATIONS CMC Connectors sealed, high-density, modular and cost-effective connection system for heavy-duty applications The CMC connector family from Molex is a sealed, high-density connection
More informationPRODUCT SPECIFICATION
1.0 SCOPE This Product Specification covers the 3.00 mm (.118 inch) centerline (pitch) square pin headers when mated with either printed circuit board (PCB) connector or connectors terminated with 20 to
More informationRIBBON CABLE CONNECTORS
TE Connectivity: Every Connection Counts 2015 TE Connectivity Ltd. family of companies. All Rights Reserved CONNECTORS RIBBON CABLE CONNECTORS TE CONNECTIVITY (TE) IDC LOW PRO HDR 30P VERT LG LA AMP-LATCH
More informationQUICKIE SHROUDED HEADERS LOW PROFILE
BOARD/WIRE-TO-BOARD CONNECTORS QUICKIE SHROUDED HEADERS LOW PROFILE FEATURES & BENEFITS Recessed pins assure proper alignment and eliminate damage during mating End windows for latching with IDC receptacle
More informationBOARD-TO-BOARD HEADERS & RECEPTACLES
TE Connectivity: Every Connection Counts 2015 TE Connectivity Ltd. family of companies. All Rights Reserved CONNECTORS BOARD-TO-BOARD HEADERS & RECEPTACLES TE CONNECTIVITY (TE) MICTOR RECEPT ASSY, 38 POS.
More informationCMC Hybrid Connectors Standard and Power Versions
The Molex family of provides a sealed, high-density, modular and cost-effective connection system for heavy-duty, powertrain and body-electronics applications in the transportation industry The CMC connector
More information7.92 mm Contact Pitch, High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed)
NEW 7.9 mm Contact Pitch, High-Current Connectors for Internal Power Supplies (UL, C-UL and TÜV Listed) DF Series Complete Locking Function Completely enclosed locking system Protection from shorts circuits
More informationBOARD/WIRE-TO-BOARD CONNECTORS MINITEK UNSHROUDED VERTICAL HEADERS
BOARD/WIRE-TO-BOARD CONNECTORS MINITEK UNSHROUDED VERTICAL HEADERS MINITEK UNSHROUDED VERTICAL HEADERS TECHNICAL INFORMATION MATERIALS Housing: High temperature, black thermoplastic Flammability rating:
More information2 2.2mm Pitch, Wire-to-Wire Connectors for Small Spaces
2 2.2mm Pitch, Wire-to-Wire Connectors for Small Spaces DF62 Series / DF62W Series Features 1. The slim, sleek design and smooth contour combine to complete connections in tight spaces. These connectors
More information343
.050" IDC CONNECTORS DUL ROW SOCKETs & Transition Plugs HFCS & HFDP SERIES Introduction: dam Tech.050" IDC Sockets and Transition Plugs are low profile, precision designed flat cable connectors that feature
More informationModular FLATPAQ. provided, and Elcon will provide samples, typically within one week.
Modular FLATPAQ Modular FLATPAQ connectors provide custom solutions to hot pluggable AC and DC power needs in a board-to-board format. By using off-the-shelf modular components, power and signal modules,
More information1mm Pitch Double Rows Low Profile Wire-to-Board Connectors
mm Pitch Double Rows Low Profile Wire-to-Board Connectors DF series Features. Contact Pitch mm contact pitch allows reliable solder and cable termination.. Reliable electrical connection wipe Effective
More informationAMP Circular Connectors for Commercial Signal & Power Applications. RoHS. Ready
MP Circular Connectors for Commercial Signal & Power pplications RoHS Ready Introduction 2 Product Facts Lightweight, all-plastic and metal-shell connectors connectors are UL 94V-0 rated and made of stabilized,
More informationGLOW WIRE CONNECTORS Product Summary
Industry photo: should be a the same image as larger industry photo. Either a different crop or different angle. Human photo. Can be environmental/documentaty style or portrait of engineer. industry photo.
More informationSPECIFICATION AND PERFORMANCE CHARACTERISTICS OF CONNECTOR SCSI INTERFACE NFDS & NFDP SERIES
SPECIFICATION AND PERFORMANCE CHARACTERISTICS OF CONNECTOR SCSI INTERFACE NFDS & NFDP SERIES CIRCUIT ASSEMBLY CORP. 18 THOMAS STREET, IRVINE, CA 92618-2777 Page 1 of 15 CONTENTS CLAUSE PAGE 1.0 SCOPE..
More informationSSL 1.1 Series. Product Data Sheet REV. 4, 2014 JUN
SSL 1.1 Series Product Data Sheet REV. 4, 2014 JUN General Specification Number of Positions Current Rating 2, 4, 6P 3A (Max) Voltage Rating Dielectric Withstand Voltage Durability Color Operating Temperature
More informationBOARD-TO-BOARD HEADERS & RECEPTACLES
TE Connectivity: Every Connection Counts 2015 TE Connectivity Ltd. family of companies. All Rights Reserved CONNECTORS BOARD-TO-BOARD HEADERS & RECEPTACLES TE CONNECTIVITY (TE) MICT,REC,038,ASY,.025,TAPE,CAP
More information1 mm Pitch Double Rows Low Profile Board-to-Cable Connectors
ll non-rohs products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales
More informationODU MINI-SNAP PC Product Description. ODU MINI-SNAP PC: The Connector with Push-Pull-Locking in Plastic
ODU MINI-SNAP PC Product Description ODU MINI-SNAP PC: The Connector with Push-Pull-Locking in Plastic Cylindrical Connectors are generally available with several locking mechanisms: The most frequently
More informationATM SERIES ATM Series
SERIES Series CONNECTOR SOLUTIONS 21 Series Overview Series connectors are a high-performance, cost-effective solution specifically designed for smaller AWG applications, while still maintaining the strengths
More informationPGA / BGA / PLCC SOCKETS
PGA / BGA / PLCC SOCKETS QUICK SELECTOR CHART PGA / BGA / PLCC PGA BGA PLCC GRID 2.54 mm INTERSTITIAL 1.27 mm 1.27 mm 1 mm SOCKETS Solder tail 156 161 165 SEE PAGE 173 Surface mount 156 161 165 166 169
More informationStandard Products Assembly Equipment Table 3M Electronic Products Division
Plug Connectors 3M plug connectors can be used with either flat cable or discrete wire and are the ideal interface for standard sockets. They can be used as a T-tap from a cable bus, a splice connector
More informationDura-ConTM Hermetic Connectors
Dura-ConTM Hermetic Connectors Standard Connectors With High Performance Hermetic Seals Catalog cinch.com Cinch Dura-Con Hermetic Connectors offers a high performance hermetic seal designed into our standard
More informationUltra-small Rack/Panel Crimp Connectors
All non- products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website search at www.hirose-connectors.com, or contact your Hirose sales representative.
More information0.703 dia. [17.86] Cord Connector Contact Arrangements Shown from rear of connector DIMENSIONS ARE FOR REFERENCE ONLY
ONLINE CATALOG SWITCHCRAFT, INC. N. Elston Ave. Chicago, IL 00 77 79-700 FAX: 77 79-19 www.switchcraft.com EN MINI WEATHERTIGHT CONNECTOR SERIES EN CORD CONNECTOR 1.8 [9.8] 0. REF 0.70 dia. [17.8] PIN
More informationApplications & Features, Type SSMP When using blind mate connectors in an application, careful consideration has to be given to choosing the right con
SSMP Push-On Connectors & Adapters THE SSMP (Sub-Sub-Miniature-Push-On) is a 1.7 mm connector, using solid dielectric interface. The connector is 70% of the size of the SMP and therefore allows even higher
More information1 mm Pitch Double Rows Low Profile Board-to-Cable Connectors
ll non-rohs products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales
More information8Rectangular Pin and Socket Connectors
AMPLIMITE Connectors, Subminiature Series Connectors 109 (Continued) Introduction Product Facts Military qualified connectors conform to the latest amendments of MIL-DTL-24308 Industrial versions available
More informationAMPMODU Interconnection System
AMPMODU Interconnection System PC/104 and PC/104- Plus Connectors x [1.7 x 1.7] x [1.7 x.54] AMPMODU mm Connectors x [.54 x.54].15 x.15 [3.18 x 3.18].156 [3.96] 1 3 4 5 6 7 Disclaimer While Tyco Electronics
More informationMCX Connectors. Alphabetical Index. Johnson Components P.O. Box 1732 Waseca, MN Fax:
MCX Connectors Alphabetical Index 133-3701-201 3 133-3701-206 3 133-3701-211 3 133-3701-216 3 133-3701-221 3 133-3701-226 3 133-3701-231 4 133-3701-236 4 133-3701-301 5 133-3701-306 5 133-3701-311 5 133-3701-316
More informationTE CONNECTIVITY (TE) 09 POS HDF RCPT, MS, LEAD FREE. AMPLIMITE HDF for Flat Ribbon Cable. TE Internal Number:
TE Connectivity: Every Connection Counts 2015 TE Connectivity Ltd. family of companies. All Rights Reserved CONNECTORS IDC D-SUB CONNECTORS TE CONNECTIVITY (TE) 09 POS HDF RCPT, MS, LEAD FREE AMPLIMITE
More informationHigh-density multi-pin connectors
High-density multi-pin connectors Mating and mounting conditions to DIN 41612/IEC 60603-2 General With the ever increasing miniaturization and higher packaging densities in highly integrated circuits there
More informationFISCHER MINIMAX TM SERIES
TECHNICAL SPECIFICATIONS FISCHER TM SERIES Fischer Connectors SA All rights reserved Web version 1.0-03.2016 Changes without prior notice FISCHER TM SERIES KEY FEATURES The Fischer MiniMax Series increases
More informationProduct Specification
USB A CONNECTOR 1 of 7 J 1.0 GENERAL This specification defines the performance, tests and quality requirements for the USB A connector. This document is composed of the following sections. 1. General
More informationPrices, specifications, statement of warranty, and other terms and conditions are subject to change without notice by Lighthorse Technologies, Inc.
Section Index Connectors Specifications... 93 Flexible Cable... 95 Panel Mount... 99 Bulkhead... 100 PCB Mount... 101 In Series Adaptors... 103 Other Information Assembly Instructions... 176 Cable Assembly...
More informationProduct Details
My Cart My Part Lists Sign In/Register English (Change) Have a Question? Chat with a Product Information Specialist What can we help you find? Products Industries Resources About TE My Account Innovation
More informationAmphenol Miniature Cylindrical Proprietary/MIL-C-26482, Series 1
Amphenol Miniature Cylindrical Proprietary/ PT PT-SE SP 3 DESIGN CHARACTERISTICS Medium size, widely used cylindrical Operating voltage to 1,000 VAC (RMS) at sea level Environment resistant Quick positive
More informationOperating voltages up to 40 kvdc Operating current up to 30 Amps Advanced contact technology Silver plated and gold plated contacts available High
Operating voltages up to 40 kvdc Operating current up to 30 Amps Advanced contact technology Silver plated and contacts available High performance insulation material General characteristics and technical
More informationProduct Details
My Cart My Part Lists Sign In/Register English (Change) Have a Question? Chat with a Product Information Specialist What can we help you find? Products Industries Resources About TE My Account Innovation
More informationM-Line Series MN Multi-Pin Plugs and Receptacles Vac, Vdc
Applications Designed for the roughest industrial applications, providing reliable, rugged service for power, control and instrumentation. For use in the roughest industrial applications, ranging from:
More informationTerminal Junction System (MIL-T and Commercial)
Introduction Product Facts The TJS connections are inherently more reliable than conventional threaded and solder terminations. The user s wiring is crimped to gold plated pin contacts, conforming the
More informationSPRING - LOADED CONNECTORS
SPRING - LOADED CONNECTORS SPRING LOADED CONNECTORS QUICK SELECTOR CHART SPRING-LOADED CONNECTORS AND PAD CONNECTORS GRID 1.25 mm 2.54 mm SINGLE ROW SINGLE ROW DOUBLE ROW SLC CONNECTORS SEE PAGE Straight
More informationSPECIFICATION MARCH MULTI MEDIA MEMORY CARD CONNECTOR. Kingfont Precision Ind. Co., Ltd. 17 FL-3, NO. 738, CHUNG CHENG ROAD.
SPECIFICATION SPEC. NO. SP0A24 REV B DATE MARCH-26-2004 PRODUCT NAME PRODUCT NO MULTI MEDIA MEMORY CARD CONNECTOR SDCMF-X07XXW1XX Kingfont Precision Ind. Co., Ltd. 738 17 3 17 FL-3, NO. 738, CHUNG CHENG
More informationProduct Specification AMP Connector USB Consortium, Plug & Receptacle. Lead Free Version
Product Specification 108-60034 AMP Connector USB Consortium, Plug & Receptacle Lead Free Version 1. Scope: 1.1 Contents: This specification covers the requirements for product performance, test methods
More informationHigh-density multi-pin connectors
High-density multi-pin connectors Mating and mounting conditions to DIN 41612/IEC 60603-2 General With the ever increasing miniaturization and higher packaging densities in highly integrated circuits there
More informationSMA Connectors. RF Coax Connectors. Product Facts
SMA Connectors Product Facts Performance to 12.4 GHz and beyond Available in various base metal options, including stainless steel, brass and zinc diecast Uses industry standard crimp tools and processes
More informationMini PCI Express Card Socket
Mini PCI Express Card Socket Document No: Page: 1 of 4 1. Scope This specification covers the material and performance requirements for the Mini PCI Express Card Socket series. 2. Applicable documents
More informationElma Bustronic CompactPCI Reference Sheet
Elma Bustronic CompactPCI Reference Sheet Rev. 4 5.10.10 The cpci reference sheet provides relevant reference material for the CompactPCI product line. The information provided may change at anytime. Elma
More informationINCHES (MILLIMETERS) CUSTOMER DRAWINGS AVAILABLE ON REQUEST
TNC Connectors Flexible Cable... 3 In-Series Adapters... 4 Specifications... 2 RF Adapter Kit Adapters... 6 N Connectors Panel Mount and In-Series Adapters... 10 Flexible Cable... 8 Specifications... 7
More informationAmphenol Miniature Cylindrical Proprietary/MIL-C-26482, Series 1
Amphenol Miniature Cylindrical Proprietary/ PT PT-SE SP 3 DESIGN CHARACTERISTICS Medium size, widely used cylindrical Operating voltage to 1,000 VAC (RMS) at sea level Environment resistant Quick positive
More informationSMA - 50 Ohm Connectors
142-0701-621 4 142-0701-626 4 142-0701-631 4 142-0701-636 4 142-0701-701 7 142-0701-706 7 142-1701-011 5 142-1701-016 5 142-1701-031 4 142-1701-036 4 142-1701-041 5 142-1701-046 5 142-1701-121 5 142-1701-126
More informationTX1/TX2/TX3 SERIES CONNECTORS
TX 1 to 3 Series connectors are two-piece PC connectors with 1.27mm (.050") contact spacing. They are designed for board-to-cable applications. Configurations include IDC sockets (TX1 and TX2) for flat
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. FEATURES AND SPECIFICATIONS Features and enefits Meets UL 1086 Section 8
More informationPower Connectors & Interconnection Systems
Product Facts Available in latch versions for VRMs up to 3 oz. Available with metal clip for VRMs over 3 oz. VRM connectors to support a wide variety of power supply standards Solder tail, press-fit and
More informationHigh Current Products Catalog Revised 4-01
Product Facts Pins and sockets have low insertion force High current ratings with very low resistance All plated products are gold or silver plated Louvertac bands have a temperature range from 196 C to
More informationHigh Current Products Catalog Revised onlinecomponents.com
Interfaces Product Facts Pins and sockets have low insertion force High current ratings with very low resistance All plated products are gold or silver plated Louvertac bands have a temperature range from
More informationTechnical data: Pin Spacing
282 Female Connectors, Double-Row Pin Spacing: 3.5 mm Universal connection for all conductor types Unique, compact, double-row connector system for conductor cross sections up to 1.5 mm 2 High-density,
More information400 Series Buccaneer BUCCANEER FOR POWER. IP68 rating tested at 1.054kg/sq cm (15lb/sq in) 10m depth for 2 weeks
IP68 rating tested at 1.054kg/sq cm (15lb/sq in) m depth for 2 weeks IP69K, Tested in accordance with DIN 40050/Part 9 IP6k9k 2 and 3 pole -, 250V rating 4, 6 and 8 pole -, 125V rating and 12 pole -, 50V
More informationTable of Contents. AMP Circular Connectors for Commercial Signal and Power Applications. Note: All part numbers are RoHS Compliant.
MP Circular Connectors for Commercial Signal & Power pplications RoHS Ready Introduction 2 Product Facts Lightweight, all-plastic and metal-shell connectors connectors are UL 94V-0 rated and made of stabilized,
More informationConnector System for Circular Contacts
Connector System for Circular Contacts Introduction The diameter 1.5 mm and diameter 2.5 mm Connector System is designed for electronic and electrical applications in motor vehicles. It fullfils all requirements
More information2mm Pitch, Multi functional Connector System. (Floating [Board-to-Board], Swing-Lock [Wire-to-Board], Short Pin)
NEW 2mm Pitch, Multi functional Connector System. (Floating [Board-to-Board], Swing-Lock [Wire-to-Board], Short Pin) DF59 Series Floating Structure in Three xial Directions (Board-to-Board Structure) X
More informationDynamic Series Connectors
D-5000 Series Series profile The Dynamic 5000 series was developed for up to 5 amperes in response to the demand for improved reliability and productivity for the main power lines in equipment. They can
More information