802.1Q Tunneling (Q-in-Q) Configuration Example NetworkLessons.com

Size: px
Start display at page:

Download "802.1Q Tunneling (Q-in-Q) Configuration Example NetworkLessons.com"

Transcription

1 1 sur 12 28/03/2018 à 17:28

2 2 sur 12 28/03/2018 à 17:28

3 3 sur 12 28/03/2018 à 17:28

4 4 sur 12 28/03/2018 à 17:28 R1(config)#interface fastethernet 0/0 R1(config-if)#no shutdown R1(config-if)#interface fastethernet 0/0.12 R1(config-subif)#encapsulation dot1q 12 R1(config-subif)#ip address R2(config)#interface fastethernet 0/0 R2(config-if)#no shutdown R2(config-if)#interface fastethernet 0/0.12 R2(config-subif)#encapsulation dot1q 12 R2(config-subif)#ip address SW1(config)#interface fastethernet 0/19 SW1(config-if)#switchport trunk encapsulation dot1q

5 5 sur 12 28/03/2018 à 17:28 SW2(config)#interface fastethernet 0/21 SW2(config-if)#switchport trunk encapsulation dot1q SW2(config-if)#switchport mode trunk SW3(config)#interface fastethernet 0/19 SW3(config-if)#switchport trunk encapsulation dot1q SW3(config-if)#switchport mode trunk SW3(config)#interface fastethernet 0/21 SW3(config-if)#switchport trunk encapsulation dot1q SW3(config-if)#switchport mode trunk SW1(config)#interface fastethernet 0/1 SW1(config-if)#switchport access vlan 123 SW1(config-if)#switchport mode dot1q-tunnel SW2(config)#interface fastethernet 0/2 SW2(config-if)#switchport access vlan 123 SW2(config-if)#switchport mode dot1q-tunnel SW3(config)#vlan 123

6 6 sur 12 28/03/2018 à 17:28 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to , timeout is 2 seconds:!!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms SW1#show dot1q-tunnel dot1q-tunnel mode LAN Port(s) Fa0/1 SW2#show dot1q-tunnel dot1q-tunnel mode LAN Port(s) Fa0/2 SW1#show interfaces fa0/19 trunk Port Mode Encapsulation Status Native vlan Fa0/19 on 802.1q trunking 1 Port Fa0/ Vlans allowed on trunk Port Fa0/19 1,123 Vlans allowed and active in management domain

7 7 sur 12 28/03/2018 à 17:28 Fa0/19 1,123 SW2#show interfaces trunk Port Mode Encapsulation Status Native vlan Fa0/21 on 802.1q trunking 1 Port Fa0/ Vlans allowed on trunk Port Fa0/21 1,123 Vlans allowed and active in management domain Port Fa0/21 1,123 Vlans in spanning tree forwarding state and not pruned SW3#show interfaces trunk Port Mode Encapsulation Status Native vlan Fa1/0/19 on 802.1q trunking 1 Fa1/0/21 auto n-802.1q trunking 1 Port Vlans allowed on trunk Fa1/0/ Fa1/0/ Port Vlans allowed and active in management domain Fa1/0/19 1,123 Fa1/0/21 1,123 Port Vlans in spanning tree forwarding state and not pruned Fa1/0/19 1,123 Fa1/0/21 1,123

8 8 sur 12 28/03/2018 à 17:28 SW1#show spanning-tree vlan 12 Spanning tree instance(s) for vlan 12 does not exist. SW2#show spanning-tree vlan 12 Spanning tree instance(s) for vlan 12 does not exist. SW3#show spanning-tree vlan 12 Spanning tree instance(s) for vlan 12 does not exist. SW1(config)interface fastethernet 0/1 SW1(config-if)#l2protocol-tunnel?

9 9 sur 12 28/03/2018 à 17:28 If you like to keep on reading, Become a Member Now! Here is Why: Learn any CCNA, CCNP and CCIE R&S Topic. Explained As Simple As Possible. Try for Just $1. The Best Dollar You've Ever Spent on Your Cisco Career! Full Access to our 607 Lessons. More Lessons Added Every Week! Content created by Rene Molenaar (CCIE #41726) 360 New Members signed up the last 30 days! 100% Satisfaction Guaranteed! You may cancel your monthly membership at any time. No Questions Asked!

10 10 sur 12 28/03/2018 à 17:28

11 JEAN CASIMIR SR NETWORK ENGINEER AUGUST 14, 2017 Can t Miss a Day Without Begin a Member NetworkLessons.com makes labs look easy and understandable. I seriously can't miss a single day without being a member of their website. NetworkLessons.com is a fantastic and very helpful e-learning site. They provide you the best and the most important knowledge that you need to get any networking job done. Thank you! 11 sur 12 28/03/2018 à 17:28

12 12 sur 12 28/03/2018 à 17:28

v5.0 Narbik Kocharians CCSI, CCIE #12410 R&S, Security, SP Physical or Logical

v5.0  Narbik Kocharians CCSI, CCIE #12410 R&S, Security, SP Physical or Logical CCIE Foundation v5.0 www.micronicstraining.com Narbik Kocharians CCSI, CCIE #12410 R&S, Security, SP Physical or Logical R&S Foundation by Narbik Kocharians CCIE R&S Foundation v5.0 Page 1 of 90 LAB 2

More information

Configuring HSRP. Global Knowledge Training LLC L5-1

Configuring HSRP. Global Knowledge Training LLC L5-1 L5 Configuring HSRP Global Knowledge Training LLC L5-1 Objectives In this lab you will examine the hot standby router protocol (HSRP). First you will configure PxR2 similar to PxR1, so they are both possible

More information

Basic switch configuration

Basic switch configuration Basic switch configuration Cisco IOS Basic switch functions, names and passwords The switch name is tool to let us see what device we are connected to. The prompt will display the name of the switch so

More information

Lab 5: Inter-VLANs Routing

Lab 5: Inter-VLANs Routing Lab 5: Inter-VLANs Routing Network Topology:- Device Interface IP Address Subnet Mask Gateway/Clock Rate Fa 0/0.10 10.5.0.1 255.255.255.192 ----- R1 Fa 0/0.20 10.6.0.1 255.255.255.192 ----- Fa 0/0.30 10.10.0.1

More information

Lab 5: Basic VLAN Configuration

Lab 5: Basic VLAN Configuration Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13

More information

Lecture (04) VTP Ports Security

Lecture (04) VTP Ports Security Lecture (04) VTP Ports Security By: Dr. Ahmed ElShafee ١ Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II VTP VLAN Trucking Protocol (VTP) is a Cisco proprietary protocol that propagates

More information

RealCiscoLAB.com. Configuring EtherChannel. Topology. Objective. Background. Required Resources. CCNPv6 Switch. Configure EtherChannel.

RealCiscoLAB.com. Configuring EtherChannel. Topology. Objective. Background. Required Resources. CCNPv6 Switch. Configure EtherChannel. RealCiscoLAB.com CCNPv6 Switch Configuring EtherChannel Topology Objective Background Configure EtherChannel. Four switches have just been installed. The distribution layer switches are Catalyst 3560 switches,

More information

STUDENT LAB GUIDE CCNA ( )

STUDENT LAB GUIDE CCNA ( ) STUDENT LAB GUIDE CCNA (640-802) Developed By, Router Infotech Career Academy LAB: 18 RAPID SPANNING TREE PROTOCOL (RSTP) Objective: To configure & Verify Rapid Spanning Tree Protocol (RSTP) successfully

More information

Interconnecting networks with switches. Virtual Local Area Networks (VLAN)

Interconnecting networks with switches. Virtual Local Area Networks (VLAN) 1 Interconnecting networks with switches. Virtual Local Area Networks (VLAN) Experimental Development Exercise 1: Creating VLANs and trunk links using the 802.1Q protocol The aims of this exercise are:

More information

Lab 19a. Router On A Stick

Lab 19a. Router On A Stick Rev. 00.0 Lab a. Router On A Stick c cnac o okbook.com G O A L Configure routing on R, enabling host H to communicate with host H, then make VLAN 0 native on the trunk. Topology You'll need A router (R)

More information

Lab 6.4.1: Basic Inter-VLAN Routing

Lab 6.4.1: Basic Inter-VLAN Routing Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 172.17.99.1 S2 VLAN 99 172.17.99.12 255.255.255.0 172.17.99.1

More information

Question 5.1. Every port on a switch is a collision domain. Every port on a router is a collision domain.

Question 5.1. Every port on a switch is a collision domain. Every port on a router is a collision domain. Question 5.1 Q 5.1.1 Number of Collision Domains: = 14 Every port on a switch is a collision domain. Every port on a router is a collision domain. Number of Broadcast Domains: = 5 Every port on a router

More information

Lab Configuring Inter-VLAN Routing

Lab Configuring Inter-VLAN Routing Lab 9.3.6 Configuring Inter-VLAN Routing Objective Create a basic switch configuration and verify it. Create multiple VLANs, name them and assign multiple member ports to them. Create a basic configuration

More information

Table of Contents. isco Configuring 802.1q Trunking Between a Catalyst 3550 and Catalyst Switches Running Integrated Cisco IOS (Nativ

Table of Contents. isco Configuring 802.1q Trunking Between a Catalyst 3550 and Catalyst Switches Running Integrated Cisco IOS (Nativ king Between a Catalyst 3550 and Catalyst Switches Running isco Configuring 802.1q Trunking Between a Catalyst 3550 and Catalyst Switches Running Integrated Cisco IOS (Nativ Table of Contents Configuring

More information

VLANs. CCNA Exploration Semester 3 Chapter Sep-13

VLANs. CCNA Exploration Semester 3 Chapter Sep-13 VLANs CCNA Exploration Semester 3 Chapter 3 1 Topics The role of VLANs in a network Trunking VLANs Configure VLANs on switches Troubleshoot common VLAN problems 2 Semester 3 LAN Design Basic Switch Concepts

More information

Advanced Troubleshooting CCIE Routing & Switching v5.0

Advanced Troubleshooting CCIE Routing & Switching v5.0 Advanced Troubleshooting CCIE Routing & Switching v5.0 www.micronicstraining.com Narbik Kocharians CCSI, CCIE #12410 R&S, Security, SP Switching-I Questions & Answers CCIE R&S by Narbik Kocharians Advanced

More information

Lab Catalyst 2950 and 3550 Series Intra-VLAN Security

Lab Catalyst 2950 and 3550 Series Intra-VLAN Security Lab 7.2.5.1 Catalyst 2950 and 3550 Series Intra-VLAN Security Objective Scenario Configure intra-vlan security with Access Control Lists (ACLs) using the command-line interface (CLI) mode. This lab will

More information

CCNA Routing & Switching Lab Workbook - Full-Scale Lab 1

CCNA Routing & Switching Lab Workbook - Full-Scale Lab 1 CCNA Routing & Switching Lab Workbook - Full-Scale Lab 1 Task 1.1 Tasks You must load the initial configuration files for the section, FS Lab-1 Initial, which can be found in CCNA Routing & Switching Topology

More information

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:

More information

::::::::Notes::::::::: (802.1q Tunneling/QinQ Tunneling)(Used for Metro-Ethernet Networks/Layer 2 VPN)

::::::::Notes::::::::: (802.1q Tunneling/QinQ Tunneling)(Used for Metro-Ethernet Networks/Layer 2 VPN) ::::::::Notes::::::::: (802.1q Tunneling/QinQ Tunneling)(Used for Metro-Ethernet Networks/Layer 2 VPN) 1.Layer 2 VPN over switched ethernet network (similar to lightweight version of MPLS L2VPN)(Any transport

More information

Internetwork Expert s CCNP Bootcamp. VLANs, Trunking, & VTP. VLANs Overview

Internetwork Expert s CCNP Bootcamp. VLANs, Trunking, & VTP. VLANs Overview Internetwork Expert s CCNP Bootcamp VLANs, Trunking, & VTP http:// VLANs Overview Virtual Local Area Network Hosts in the same VLAN share the same broadcast domain Switches create a separate CAM table

More information

Lab Configuring and Testing the Rapid Spanning Tree Prototype

Lab Configuring and Testing the Rapid Spanning Tree Prototype Lab 7.3.3 Configuring and Testing the Rapid Spanning Tree Prototype Device Designation Device Name IP Address Subnet Mask Default Gateway Fa0/0.1 10.0.0.1 255.255.255.0 R1 BR4 Fa0/0.10 10.10.10.254 255.255.255.0

More information

Lab 5.6b Configuring AAA and RADIUS

Lab 5.6b Configuring AAA and RADIUS Lab 5.6b Configuring AAA and RADIUS Learning Objectives Install CiscoSecure ACS Configure CiscoSecure ACS as a RADIUS server Enable AAA on a router using a remote RADIUS server Topology Diagram Scenario

More information

STUDENT LAB GUIDE CCNA ( )

STUDENT LAB GUIDE CCNA ( ) STUDENT LAB GUIDE CCNA (640-802) Developed By, Router Infotech Career Academy LAB: 09 Static Route Configuration Objective: To configure & implement Static Route successfully on said devices and test its

More information

Chapter 8 Lab 8-3, Configuring 6to4 Tunnels

Chapter 8 Lab 8-3, Configuring 6to4 Tunnels Chapter 8 Lab 8-3, Configuring 6to4 Tunnels Topology Objectives Configure EIGRP for IPv4. Create a 6to4 tunnel. Configure static IPv6 routes. Background In this lab, you configure EIGRP for full connectivity

More information

Sybex CCENT Chapter 11: VLANs and Inter-VLAN Routing. Instructor & Todd Lammle

Sybex CCENT Chapter 11: VLANs and Inter-VLAN Routing. Instructor & Todd Lammle Sybex CCENT 100-101 Chapter 11: VLANs and Inter-VLAN Routing Instructor & Todd Lammle Chapter 11 Objectives The CCENT Topics Covered in this chapter include: LAN Switching Technologies Describe how VLANs

More information

Troubleshooting VLANs and Trunks

Troubleshooting VLANs and Trunks L2 Troubleshooting VLANs and Trunks Global Knowledge Training LLC L2-1 Objectives In this lab you will download configuration files into PxSW s running configuration to introduce VLAN and trunking issues

More information

LAN Troubleshooting. Ethernet Troubleshooting

LAN Troubleshooting. Ethernet Troubleshooting CCIE Routing & Switching Advanced Troubleshooting Bootcamp LAN Troubleshooting http:// Ethernet Troubleshooting No Ethernet switching troubleshooting in Troubleshooting Section, but it can be included

More information

Lab 2-5 EIGRP Authentication and Timers

Lab 2-5 EIGRP Authentication and Timers Lab 2-5 EIGRP Authentication and Timers Learning Objectives Review basic configuration of EIGRP Configure and verify EIGRP authentication parameters Configure EIGRP hello interval and hold time Verify

More information

Chapter 8 Lab 8-2, Using Manual IPv6 Tunnels with EIGRP for IPv6

Chapter 8 Lab 8-2, Using Manual IPv6 Tunnels with EIGRP for IPv6 Chapter 8 Lab 8-2, Using Manual IPv6 Tunnels with EIGRP for IPv6 Topology Objectives Configure EIGRP for IPv4. Create a manual IPv6 tunnel. Configure EIGRP for IPv6 across the tunnel. Background In this

More information

Packet Tracer - Connect a Router to a LAN (Instructor Version)

Packet Tracer - Connect a Router to a LAN (Instructor Version) (Instructor Version) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Topology Addressing Table Device Interface IP Address Subnet Mask Default

More information

CCNP Lab 006 Solution: HSRP and Switch Security

CCNP Lab 006 Solution: HSRP and Switch Security ABOUT CONTACT FAQ JOIN HOME CCNA CCNP COMPTIA DESIGN You are here: Home / 101 CCNP Labs Solutions / CCNP Lab 006 Solution: HSRP and Switch Security CCNP Lab 006 Solution: HSRP and Switch Security Lab Objective:

More information

Lab 7.5.3: Troubleshooting the Wireless WRT300N

Lab 7.5.3: Troubleshooting the Wireless WRT300N Lab 7.5.3: Troubleshooting the Wireless WRT300N Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/1.5 5.5.5.10 255.255.255.0 N/A Fa0/1.10 192.168.10.1 255.255.255.0

More information

the larger the number of users and devices, the more broadcasts and packets each switch must handle.

the larger the number of users and devices, the more broadcasts and packets each switch must handle. VLANs Introduction By default, routers allow broadcasts to occur only within the originating network, while switches forward broadcasts to all segments. Flat network = one broadcast domain. that the largest

More information

Chapter 5 Lab 5-1 Inter-VLAN Routing INSTRUCTOR VERSION

Chapter 5 Lab 5-1 Inter-VLAN Routing INSTRUCTOR VERSION CCNPv7.1 SWITCH Chapter 5 Lab 5-1 Inter-VLAN Routing INSTRUCTOR VERSION Topology Objectives Implement a Layer 3 EtherChannel Implement Static Routing Implement Inter-VLAN Routing Background Cisco's switching

More information

Lab Analyzing a Test Plan and Performing a Test

Lab Analyzing a Test Plan and Performing a Test Lab 7.1.6 Analyzing a Test Plan and Performing a Test Objectives Analyze a sample test plan to determine: The subject of the test The methods and tools for testing The potential results Perform the test

More information

Lab 4.9 QoS Pre-classify

Lab 4.9 QoS Pre-classify Lab 4.9 QoS Pre-classify Learning Objectives Configure a GRE tunnel Configure QoS pre-classify Verify QoS pre-classify operation Topology Diagram Scenario Weighted fair queuing (WFQ) allows routers to

More information

3 ROUTER SETUP WITH FRAME RELAY CONFIGURATION OF FRAME RELAY ROUTER

3 ROUTER SETUP WITH FRAME RELAY CONFIGURATION OF FRAME RELAY ROUTER 3 ROUTER SETUP WITH FRAME RELAY R2 s0 Network 192.168.1.0 s1 DCE * Frame Relay Network * s0 192.168.1.0 s0 DCE R1 Hardware Requirement: 1 Router with t 2 Serials 2 Router with 1 Serial 2 DTE/DCE Serial

More information

Implement Static Routes for IPv6 Configuration Example

Implement Static Routes for IPv6 Configuration Example Implement Static Routes for IPv6 Configuration Example Document ID: 113361 Contents Introduction Prerequisites Components Used Conventions Configure Network Diagram Configurations Verify Related Information

More information

CCNA TECHNOLOGIES SERIES

CCNA TECHNOLOGIES SERIES CCNA TECHNOLOGIES SERIES ONLINE TRAINING CLASS CHAPTER 01 BURMESE VERSION Phyo Phyo Hein B. C. Tech (hons) MTCNA, MTCRE, MTCWE, MTCTCE, MTCUME, MTCINE CCNA R&S, CCNP R&S, CCIP, JNCIA-Junos, JNCDA May 15,

More information

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and

This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:

More information

Lab 3.5.1: Basic Frame Relay

Lab 3.5.1: Basic Frame Relay Lab 3.5.1: Basic Frame Relay Topology Diagram Addressing Table Device Interface IP Address Subnet Mask R1 R2 Default Gateway Fa0/0 192.168.10.1 255.255.255.0 N/A S0/0/1 10.1.1.1 255.255.255.252 N/A S0/0/1

More information

CCENT Study Guide. Chapter 11 VLANs and Inter-VLAN Routing

CCENT Study Guide. Chapter 11 VLANs and Inter-VLAN Routing CCENT Study Guide Chapter 11 VLANs and Inter-VLAN Routing Chapter 11 Objectives The CCENT Topics Covered in this chapter include: 2.0 LAN Switching Technologies 2.4 Configure, verify, and troubleshoot

More information

Lab Routing Between an External Router and an Internal Route Processor

Lab Routing Between an External Router and an Internal Route Processor Lab 5.3.4.2 Routing Between an External Router and an Internal Route Processor Objective Scenario The purpose of this lab is to configure routing between an internal route processor and an external router.

More information

Lab 4.2.5a Connectivity Tests Ping

Lab 4.2.5a Connectivity Tests Ping Lab 4.2.5a Connectivity Tests Ping Objective Use the ping command to send ICMP datagrams to target host. Verify that the network layer between source and destination is working properly. Retrieve information

More information

Cisco 360 CCIE R&S Advanced Workshop 2 Assessment Lab 1

Cisco 360 CCIE R&S Advanced Workshop 2 Assessment Lab 1 CIERSASSESS-5-AK Cisco 360 CCIE R&S Advanced Workshop 2 Assessment Lab 1 The Cisco 360 CCIE Routing and Switching (R&S) Advanced Workshop 2 is a five-day course for CCIE candidates who are ready to attempt

More information

Lab Catalyst 2950T and 3550 Series Static VLANS

Lab Catalyst 2950T and 3550 Series Static VLANS Lab 2.9.1 Catalyst 2950T and 3550 Series Static VLANS Objective Create and maintain VLANs on a Cisco Catalyst 2950T or 3550 series Ethernet switch using the command-line interface (CLI) mode. Scenario

More information

Lab Configuring and Verifying Standard IPv4 ACLs (Instructor Version Optional Lab)

Lab Configuring and Verifying Standard IPv4 ACLs (Instructor Version Optional Lab) (Instructor Version Optional Lab) Instructor Note: Red font color or gray highlights indicate text that appears in the instructor copy only. Optional activities are designed to enhance understanding and/or

More information

Lab Troubleshooting Using traceroute Instructor Version 2500

Lab Troubleshooting Using traceroute Instructor Version 2500 Lab 9.3.4 Troubleshooting Using traceroute Instructor Version 2500 294-833 CCNA 2: Routers and Routing Basics v 3.1 - Lab 9.3.4 Copyright 2003, Cisco Systems, Inc. Objective Use the traceroute Cisco IOS

More information

Lab Configuring and Verifying Standard ACLs Topology

Lab Configuring and Verifying Standard ACLs Topology Topology 2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 9 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1

More information

Lab Catalyst 2950T and 3550 Series Basic Setup

Lab Catalyst 2950T and 3550 Series Basic Setup Lab 1.2.9.1 Catalyst 2950T and 3550 Series Basic Setup Objective Configure a Cisco Catalyst 2950T or 3550 series Ethernet switch for the first time using the command-line interface (CLI) mode. Basic first

More information

Lab 19(b)2. L3 Switch Routed Ports

Lab 19(b)2. L3 Switch Routed Ports Lab 9(b). L Switch Routed Ports Rev. 000.0 c cnac o okbook.com G O A L onfigure a routed port on to communicate with R. Topology For simplicity, you can reuse the physical topology of the previous labs,

More information

Lab 5.5.2: Challenge Spanning Tree Protocol

Lab 5.5.2: Challenge Spanning Tree Protocol Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13

More information

University of Jordan Faculty of Engineering & Technology Computer Engineering Department Advance Networks Laboratory Exp.4 Inter-VLAN Routing

University of Jordan Faculty of Engineering & Technology Computer Engineering Department Advance Networks Laboratory Exp.4 Inter-VLAN Routing University of Jordan Faculty of Engineering & Technology Computer Engineering Department Advance Networks Laboratory 0907529 Exp.4 Inter-VLAN Routing Objectives 1. Describe the three primary options for

More information

Configuring EtherChannel

Configuring EtherChannel L4 Configuring EtherChannel Global Knowledge Training LLC L4-1 Objectives In this lab you will first verify that one of the parallel connections to the core switch is blocked by STP. You will then configure

More information

Lab Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking

Lab Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking Lab 2.9.2 Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking Objective Configure a VLAN trunk between two Cisco Catalyst WS-C2950T-24-EI switches and a Cisco Catalyst WS-C3550-24-EMI switch in

More information

Lab Inter-VLAN Routing with the Internal Route Processor

Lab Inter-VLAN Routing with the Internal Route Processor Lab 5.3.4.1 Inter-VLAN Routing with the Internal Route Processor Objective Scenario The purpose of this lab is to configure Inter-VLAN routing using a switch with an internal route processor. The network

More information

Lab 3.3 Configuring Wireshark and SPAN

Lab 3.3 Configuring Wireshark and SPAN Lab 3.3 Configuring Wireshark and SPAN Learning Objectives Install Wireshark on a host PC Configure a switch to use the SPAN monitoring tool. Topology Diagram Scenario In this lab, you will configure a

More information

LAN Switching and Wireless

LAN Switching and Wireless LAN Switching and Wireless CCNA Exploration Labs and Study Guide Allan Johnson ii LAN Switching and Wireless, CCNA Exploration Labs and Study Guide LAN Switching and Wireless CCNA Exploration Labs and

More information

Lab Configuring EtherChannel

Lab Configuring EtherChannel Topology Addressing Table Objectives Device Interface IP Address Subnet Mask S1 VLAN 99 192.168.99.11 255.255.255.0 S2 VLAN 99 192.168.99.12 255.255.255.0 S3 VLAN 99 192.168.99.13 255.255.255.0 PC-A NIC

More information

Lecture (06) Design and Configuration LAN Practicing, working on CISCO equipment. By: Dr. Ahmed ElShafee

Lecture (06) Design and Configuration LAN Practicing, working on CISCO equipment. By: Dr. Ahmed ElShafee Lecture (06) Design and Configuration LAN Practicing, working on CISCO equipment By: Dr. Ahmed ElShafee ١ Dr. Ahmed ElShafee, ACU : Fall 2015, Practical App. Networks II Part I ٢ ٣ SW01 steps firstly connect

More information

1 of :22

1 of :22 Feedback: Help us help you Please rate this document. Excellent Good Average Fair Poor This document solved my problem. Yes No Just Browsing Suggestions to improve this document. (512 character limit)

More information

Configuring IS IS over IPv6

Configuring IS IS over IPv6 Configuring IS IS over IPv6 Document ID: 40262 Contents Introduction Prerequisites Requirements Components Used Conventions Configure Network Diagram Configurations Verify Troubleshoot Troubleshooting

More information

Lab Configuring and Verifying Standard IPv4 ACLs Topology

Lab Configuring and Verifying Standard IPv4 ACLs Topology Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 10 Addressing Table Objectives Device Interface IP Address Subnet Mask Default Gateway R1 G0/1 192.168.10.1

More information

Lecture (08) STP - CDP. Dr. Ahmed M. ElShafee CDP STP. tweak this simple design to make it more resilient by adding

Lecture (08) STP - CDP. Dr. Ahmed M. ElShafee CDP STP. tweak this simple design to make it more resilient by adding Lecture (08) STP - CDP STP CDP Dr. Ahmed M. ElShafee ١ ٢ Such design creates a single point of failure. We could easily tweak this simple design to make it more resilient by adding an extra path between

More information

Lab 9.1.5a Trunking with ISL 2924XL Series

Lab 9.1.5a Trunking with ISL 2924XL Series Lab 9.1.5a Trunking with ISL 2924XL Series Objective Create a basic switch configuration and verify it. Create multiple VLANs, name them and assign multiple member ports to them. Create an ISL trunk line

More information

EtherSwitch Service Module (ES) Configuration Example

EtherSwitch Service Module (ES) Configuration Example EtherSwitch Service Module (ES) Configuration Example Document ID: 82288 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions EtherSwitch Modules Concepts Configure

More information

Lab 9.1.5b Trunking with 802.1q

Lab 9.1.5b Trunking with 802.1q Lab 9.1.5b Trunking with 802.1q Objective Create a basic switch configuration and verify it. Create multiple VLANs, name them and assign multiple member ports to them. Create an 802.1q trunk line between

More information

Table of Contents. co Configuring InterVLAN Routing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2950 Switch Using An Extern

Table of Contents. co Configuring InterVLAN Routing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2950 Switch Using An Extern outing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2 co Configuring InterVLAN Routing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2950 Switch Using An Extern Table of Contents Configuring

More information

Ch. 9 VTP (Trunking, VTP, Inter-VLAN Routing) CCNA 3 version 3.0

Ch. 9 VTP (Trunking, VTP, Inter-VLAN Routing) CCNA 3 version 3.0 Ch. 9 VTP (Trunking, VTP, Inter-VLAN Routing) CCNA 3 version 3.0 Overview Explain the origins and functions of VLAN trunking Describe how trunking enables the implementation of VLANs in a large network

More information

Lab - Troubleshooting Connectivity Issues

Lab - Troubleshooting Connectivity Issues Lab - Troubleshooting Connectivity Issues Topology Addressing Table R1 ISP Objectives Device Interface IP Address Subnet Mask Default Gateway G0/1 192.168.1.1 255.255.255.0 N/A S0/0/0 10.1.1.1 255.255.255.252

More information

Copyright 2009 Internetwork Expert i

Copyright 2009 Internetwork Expert i Copyright Information, Inc. All rights reserved. The following publication, CCNP Lab Workbook, was developed by Internetwork Expert, Inc. All rights reserved. No part of this publication may be reproduced

More information

Wireless LAN Controller Module Configuration Examples

Wireless LAN Controller Module Configuration Examples Wireless LAN Controller Module Configuration Examples Document ID: 70530 Contents Introduction Prerequisites Requirements Components Used Conventions Basic Configuration Example 1 Basic Configuration with

More information

configuring and connecting 24

configuring and connecting 24 Lecture (01) configuring and connecting 24 ports switch Dr. Ahmed M. ElShafee ١ ٢ Step 1: connecting your PC to the Console Port. Open HyperTerminal software Press RETURN to get started. Switch> (User

More information

Lecture (01) configuring and connecting 24 ports switch

Lecture (01) configuring and connecting 24 ports switch Lecture (01) configuring and connecting 24 ports switch Dr. Ahmed M. ElShafee ١ ٢ Step 1: connecting your PC to the Console Port. Open HyperTerminal software Press RETURN to get started. Switch> (User

More information

Activity 2.5.1: Basic PPP Configuration

Activity 2.5.1: Basic PPP Configuration Activity 2.5.1: Basic PPP onfiguration Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 Fa0/1 192.168.10.1 255.255.255.0 N/A S0/0/0 10.1.1.1 255.255.255.252

More information

Lab 3.2 Configuring a Basic GRE Tunnel

Lab 3.2 Configuring a Basic GRE Tunnel Lab 3.2 onfiguring a Basic GRE Tunnel Learning Objectives onfigure a GRE tunnel onfigure EIGRP on a router onfigure and test routing over the tunnel interfaces Topology iagram Scenario This lab is designed

More information

Implement Inter-VLAN Routing. LAN Switching and Wireless Chapter 6 Modified by Tony Chen 11/01/2008

Implement Inter-VLAN Routing. LAN Switching and Wireless Chapter 6 Modified by Tony Chen 11/01/2008 Implement Inter-VLAN Routing LAN Switching and Wireless Chapter 6 Modified by Tony Chen 11/01/2008 ITE I Chapter 6 2006 Cisco Systems, Inc. All rights reserved. Cisco Public 1 Notes: If you see any mistake

More information

CCNA Fault Finding Labs

CCNA Fault Finding Labs Copyright 2007-2019 Commsupport Networks Ltd. All rights reserved. The following publication, CCNA Fault Finding Lab Workbook series, was developed by Commsupport Networks Ltd. All rights reserved. No

More information

SEDINTA 2. Configurare VTP propagarea VLANrilor in cadrul retelei interne. VTP = VLAN Trunking Protocol

SEDINTA 2. Configurare VTP propagarea VLANrilor in cadrul retelei interne. VTP = VLAN Trunking Protocol SEDINTA 2 Configurare VTP propagarea VLANrilor in cadrul retelei interne VTP = VLAN Trunking Protocol - allows for the propagation of VLAN s from a single switch to multiple switches (Server-Client architecture)

More information

Scenario 3 3: VTP Pruning

Scenario 3 3: VTP Pruning Scenario 3 3: VTP Pruning In the previous scenario, the list of allowed VLANs is configured manually. This configuration is static, which means that if you need to enable a previously disallowed VLAN on

More information

Chapter 2 Lab 2-1, EIGRP Configuration, Bandwidth, and Adjacencies

Chapter 2 Lab 2-1, EIGRP Configuration, Bandwidth, and Adjacencies Chapter 2 Lab 2-1, EIGRP Configuration, Bandwidth, and Adjacencies Topology Objectives Background Configure EIGRP on multiple routers. Configure the bandwidth command to modify the EIGRP metric. Verify

More information

SWITCH Lab Guide Labs powered by

SWITCH Lab Guide Labs powered by SWITCH Lab Guide 300-115 ii SWITCH 300-115 Lab Guide LM20170908/BV1.0 iii 25 C e n tur y Blvd., S te. 5 0 0, N a s hvill e, T N 37214 B o s o n.c o m To perform the labs referenced in this book, please

More information

Lab 6-1 Configuring a WLAN Controller

Lab 6-1 Configuring a WLAN Controller Lab 6-1 Configuring a WLAN Controller Topology Diagram Scenario In the next two labs, you will configure a wireless solution involving a router with a built-in WLAN controller, two lightweight wireless

More information

Chapter 10 - Configure ASA Basic Settings and Firewall using ASDM

Chapter 10 - Configure ASA Basic Settings and Firewall using ASDM Chapter 10 - Configure ASA Basic Settings and Firewall using ASDM This lab has been updated for use on NETLAB+ Topology Note: ISR G1 devices use FastEthernet interfaces instead of GigabitEthernet interfaces.

More information

Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)

Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) Cisco 200-105 Dumps Available Here at: /cisco-exam/200-105-dumps.html Enrolling now you will get access to 170 questions in a unique set of

More information

Lab 1: OSPF With Three Routers

Lab 1: OSPF With Three Routers Lab 1: OSPF With Three Routers The physical topology is as shown in FIG 18.1 - Advanced OSPF Lab. FIG 18.1 - Advanced OSPF Lab Lab Exercise Your task is to configure the network in FIG 18.1 - Advanced

More information

Chapter 4: Secure Routing and Switching

Chapter 4: Secure Routing and Switching Chapter 4: Secure Routing and Switching Technology Brief One aspect in computer networks security is securing the end-users mobile traffic along with access and management of networking devices. Another

More information

Lab 6-1 Configuring a WLAN Controller

Lab 6-1 Configuring a WLAN Controller Lab 6-1 Configuring a WLAN Controller Topology Diagram Scenario Step 1 In the next two labs, you will configure a wireless solution involving a WLAN controller, two lightweight wireless access points,

More information

Chapter 3: VLANs. Routing & Switching

Chapter 3: VLANs. Routing & Switching Chapter 3: VLANs Routing & Switching VLAN Definitions A VLAN is a logical partition of a Layer 2 network. VLANs logically group hosts, regardless of physical location. Multiple partitions can be created,

More information

EIGRP Lab / lo1. .1 lo / /30

EIGRP Lab / lo1. .1 lo / /30 EIGRP Lab 172,16,1.0/24.1 lo1 192.168.20.0/30.2.1 Merida fa0 fa0 Vargas lo2.1 lo2.5.1 lo1 192.168.30.0/24 172.16.2.0/24 192.168.20.4.0/30 Scenario: Loopback0 is used for RouterID Loopback1 is a virtual

More information

Maintaining Specific VLAN Identification. Comparing ISL and 802.1Q. VLAN Trunking

Maintaining Specific VLAN Identification. Comparing ISL and 802.1Q. VLAN Trunking Maintaining Specific VLAN Identification Specifically developed for multi-vlan interswitch communications Places a unique identifier in each frame Functions at Layer 2 2003, Cisco Systems, Inc. All rights

More information

CCNP Bootcamp. Introduction

CCNP Bootcamp. Introduction 0101010101010101101010101010101011010101010101010110101010101010101010101010101011010101010101010 010101010101010110101010101010101010101010101011010101010101010110101010101010101101010101010101 1010101010101011010101010101010110101010101010101101010101010101010101010101010110101010101010101

More information

Lab 6-1 Configuring a WLAN Controller

Lab 6-1 Configuring a WLAN Controller Lab 6-1 Configuring a WLAN Controller Topology Diagram Scenario In the next two labs, you will configure a wireless solution involving a WLAN controller, two lightweight wireless access points, and a switched

More information

LAB 5: DMVPN BGP. LAB 5: Diagram. Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M.

LAB 5: DMVPN BGP. LAB 5: Diagram. Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M. LAB 5: DMVPN BGP LAB 5: Diagram Note: This Lab was developed on Cisco IOS Version15.2(4) M1 ADVENTERPRISEK9-M. LAB 5: Configure BGP over DMVPN Configuration Step 1: Enable loopback and physical interfaces

More information

Lab 2.5.1: Basic PPP Configuration Lab

Lab 2.5.1: Basic PPP Configuration Lab Topology Diagram Addressing Table Device Interface IP Address Subnet Mask R1 R2 R3 Default Gateway Fa0/1 192.168.10.1 255.255.255.0 N/A S0/0/0 10.1.1.1 255.255.255.252 N/A Lo0 209.165.200.225 255.255.255.224

More information

Configuring Catalyst Switches for Polycom Conference Phones

Configuring Catalyst Switches for Polycom Conference Phones Configuring Catalyst Switches for Polycom Conference Phones Document ID: 97229 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions Background Information Configure

More information

Building the Routing Table. Introducing the Routing Table Directly Connected Networks Static Routing Dynamic Routing Routing Table Principles

Building the Routing Table. Introducing the Routing Table Directly Connected Networks Static Routing Dynamic Routing Routing Table Principles Building the Routing Table Introducing the Routing Table Directly Connected Networks Static Routing Dynamic Routing Routing Table Principles Introducing the Routing Table R1# show ip route Codes: C - connected,

More information

Cisco Configuring Hub and Spoke Frame Relay

Cisco Configuring Hub and Spoke Frame Relay Table of Contents Configuring Hub and Spoke Frame Relay...1 Introduction...1 Before You Begin...1 Conventions...1 Prerequisites...1 Components Used...1 Configure...1 Network Diagram...2 Configurations...2

More information

CONFIGURATION DU SWITCH

CONFIGURATION DU SWITCH Current configuration : 2037 bytes version 12.2 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption hostname Switch no aaa new-model ip subnet-zero

More information