Rotary Push-switch Wall Dimmer RPS

Transcription

1 RPS ROTARY PUSH-SWITCH WA DIMMR. PAG 1 OF 5 Rotary Push-switch Wall Dimmer RPS and mains switching rotary module to fit into plates and grid systems Contents Technical specification and installation 2 Related product options 3 Wiring diagrams One-way switching and of drive units 3 Two-way switching and of drive units 4 Individual switching and of drive units 4 Wired to Drose DR100 5 Product order codes Mains switching and 2-wire control of a single drive unit Mains switching and 2-wire control of between 2-20 drive units For use with VoltMaster only RPS3 3-wire potentiometer control See VoltMaster TechPack Multiload 2 Rosemont Road Hampstead ondon W3 6 Telephone 44(0)

2 RPS ROTARY PUSH-SWITCH WA DIMMR. PAG 2 OF 5 Technical specification and installation Mains 10A switch terminals 1 COM AC 10A 2 minimum brightness preset DC 0-10V C1 C2 maximum brightness preset 0-10V control terminals front view back view top view Modules can be supplied to fit wall plates and grid systems from UK wall-plate manufacturers. Contact Multiload on 44(0) to ensure compatibility with specified plate type and finish. Shown above is module supplied for fitting into MKGridPlus. and mains switching of a single lighting drive such as D drivers and fluorescent ballasts and mains switching of between 2 to 20 lighting drives such as D drivers and fluorescent ballasts Technical specification Mains voltage: AC /- 10% (protect by 10A MCB) Mains output: switched mains output 3-wire terminal for change-over switching Signal output: DC (sink current capability only, allowing use with standard drives, such as D drivers, fluorescent ballasts or other drive units) Mains switching: 10A (resistive). The number of drives that can be switched is determined by the current draw of the drives up to a total maximum of 10A. Isolation: signal circuitry and terminals are isolated from mains circuitry and terminals (SV) Dimensions: MK module :50mm W:25mm D:30mm Knob Diam: 20mm H:13mm Fixing: Bush M10 Shaft:6mm nvironmental specification Temperature range: -10ºC 50ºC Maximum humidity: ess than 95% non-condensing Installation and set up procedure Installation should be carried out by suitably qualified personnel in accordance with good electrical practice and the appropriate national wiring regulations. Switch off mains electrical supply before commencing installation. Protective earth (P) must be connected for metal back plates, and when standards dictate. The device may be used for permanent interior installations in dry locations with suitable surface plates fitted. Terminals C1 (-ve 0V) C2 (ve 0-10V) ow voltage 2-wire 0-10V analogue control by rotation of the control knob. The module can be wired to a large number of D drivers or fluorescent ballasts or other 0-10V controlled drive units without an effect on brightness if some drive units are switched on/off by the mains. Mains switching multi-way In addition push on/push off action of the control knob provides on/off switching of mains power (2-core mains cable earth if required) or changeover switching (3-core mains cable earth if required) for 2 way mains switching. Setting minimum and maximum brightness asy access minimum and maximum brightness screwdriver presets set the range covered by the rotary control. Set the minimum preset first: setting the maximum will not affect minimum setting. Brightness levels are not affected by temperature changes around the module. Multiload 2 Rosemont Road Hampstead ondon W3 6 Telephone 44(0)

3 RPS ROTARY PUSH-SWITCH WA DIMMR. PAG 3 OF 5 Rotary Push-Switch Wall Dimmer RPS related product options PROTCTD MAIS VOTAG SUPPY SWITCHD COTRO SIGA 0-10V OY O COTRO SIGA OPTIO TO B COCTD D Drive Constant Voltage D Drive Constant Current Fluorescent D DRIV D DRIV ROTARY DIMMIG FUORSCT BAAST D IGHT GI Constant voltage drivers Constant voltage drivers : for a single drive : for 2-20 drive units, maintaining the full signal range up to 10V maximum brightness Switched output: One-way switching and of drive units SUITABY RATD CIRCUIT PROTCTIO TOTA SWITCH OAD OT TO XCD 10A 1 COM 2 IPUT DIMMAB DRIV D / FUORSCT SIGA 0-10V SIGA DRAWIG OT TO SCA WD-RPS-DRIV1. ISS Multiload 2 Rosemont Road Hampstead ondon W3 6 Telephone 44(0)

4 RPS ROTARY PUSH-SWITCH WA DIMMR. PAG 4 OF 5 Two-way switching and of drive units xpansion to multi-way switching by connection of intermediate switch SUITABY RATD CIRCUIT PROTCTIO TOTA SWITCH OAD OT TO XCD 10A 1 COM 2 RMOT SWITCH IPUT DIMMAB DRIV D / FUORSCT SIGA 0-10V SIGA DRAWIG OT TO SCA WD-RPS-DRIV2. ISS Individual switching and of drive units Drive units on same 0-10V or can be individually mains-switched (without affecting brightness) SUITABY RATD CIRCUIT PROTCTIO 1 COM 2 IPUT IPUT DIMMAB DRIV D / FUORSCT RMOT SWITCH TOTA SWITCH OAD OT TO XCD 10A DIMMAB DRIV D / FUORSCT SIGA SIGA SIGA DRAWIG OT TO SCA WD-RPS-DRIV3. ISS Multiload 2 Rosemont Road Hampstead ondon W3 6 Telephone 44(0)

5 RPS ROTARY PUSH-SWITCH WA DIMMR. PAG 5 OF 5 Rotary Push-switch Wall Dimmer RPS wired to Drose DR100 SUITABY RATD CIRCUIT PROTCTIO POWR SUPPY 24V DC Drose DR100 C2 C1 C DIM COTRO 1 COM 2 DC DC D 15V 0V ve -ve C1 C2 To additional Drose DR100 Combination of which must be within 85% of the rating of the power supply Use when more than one Drose DR100 is installed DRAWIG OT TO SCA WD-RPS-DR100. ISS Multiload 2 Rosemont Road Hampstead ondon W3 6 Telephone 44(0)