PCCextend 140 CardBus Extender User s Manual
|
|
|
- Phillip Marsh
- 5 years ago
- Views:
Transcription
1 PCCextend 140 CardBus Extender User s Manual Preliminary M July 1996 Sycard Technology 1180-F Miraloma Way Sunnyvale, CA (408) (408) FAX
2
3 PCCextend 140 User s Manual Page Introduction Sycard Technology's PCCextend 140 CardBus extender card is a debug tool for development and test of PC cards and hosts. PCCextend offers the following features: PCCswitch simulates card removal/insertion cycle Low profile design compatible with type I, II and III sockets 6-layer construction to insure a low noise environment All 68 pins available as test points 32-bit CardBus signals clearly marked Vcc can be isolated through jumper blocks for current measurements Surface mount components can be added in series to any signal line Vcc LEDs indicate 3.3V or 5V operation Convenient grounding posts for scope probes or other test equipment Includes plastic overlay with 16-bit and Zoomed Video signals Optional HP Logic Analyzer Adapter (PCCextend 145) available. 2.0 Using the PCCextend 140 Using the PCCextend is relatively straightforward. The extender card is inserted into the desired slot in the host system. Then the PC Card under test is inserted into the card connector. Caution: Insertion and removal of the extender and PC card should be done with care. The PC Card's fragile connectors may be broken or bent if improper force is used. Both card and extender should be inserted straight without any lateral movement or force. Proper care and use of the extender card will insure years of trouble free operation. M Sycard Technology
4 Page 2 PCCextend 140 User s Manual RUN# AD29 AD26 AD24 AD22 AD20 Vcc AD14 AD11 AD5 AD1 RFU AD27 AD25 AD23 AD21 AD18 Vpp1 AD12 AD9 AD7 AD3 AD0 CD2# AD30 STSCH AD17 Vcc RFU AD15 AD8 AD6 AD2 AD31 AD28 AD19 DEVSEL# AD16 AD13 AD10 RFU AD4 -CD1 Vcc Gnd C7 SW1 D2 C6 C8 5V PWR Gnd C4 J1 J2 C3 R1 R2 R3 R5 R7 R9 R12 R15 R10 R13 R16 R20 R24 R28 R32 R36 V1 JP1 JP2 SW2 Gnd J2A C5 R18 R22 R26 R30 R34 R38 R42 R40 R44 R47 R50 R53 R56 R58 PCCextend CARDBUS Figure The PCCextend Sycard Technology M
5 PCCextend 140 User s Manual Page Test points All 68 pins of the interface are available to probe through clearly marked headers. In addition, two ground posts can be used to ground scope or logic analyzer probes. An optional HP logic analyzer adapter (PCCextend 145) can be connected to the test points for direct interface to HP logic analyzers. Vcc Gnd C3 C7 Gnd J1 J2 SW1 RUN# AD29 AD26 AD24 AD22 AD20 Vcc AD14 AD11 AD5 AD1 RFU AD27 AD25 AD23 AD21 AD18 Vpp1 AD12 AD9 AD7 AD3 AD0 CD2# AD30 STSCH AD17 Vcc RFU AD15 AD8 AD6 AD2 AD31 AD28 AD19 DEVSEL# AD16 AD13 AD10 RFU AD4 -CD1 R1 R2 R3 R5 R7 R9 R12 R15 R18 R22 R26 R30 R34 R38 R42 R10 R13 R16 R20 R24 R28 R32 R36 R40 R44 R47 R50 R53 R56 R58 C4 C5 V1 JP1 JP2 J2A SW2 D2 5V PWR C6 C8 Gnd 2.2 Power Indicators Two LED power indicators display the status of the socket s Vcc. The PWR LED indicates that power is applied to the board. When both the PWR LED and the 5V LED are lit, a Vcc of greater than approximately 3.5V is present. When only the PWR LED is lit, the Vcc is at a level of less than 3.5V. Note: The power LEDs are designed to indicate the presence of power on the Vcc supply pins. The LEDs do not provide an accurate measurement of Vcc. Use a voltmeter to determine the actual operating voltage. 2.2 Current Measurements The Vcc power bus may be isolated from the PC Card socket through two jumper blocks. Both jumpers must be removed to isolate the power. A current meter can be inserted to measure a card s current consumption. Caution: Care must be taken to insure that the current measuring device is inserted before turning on power to the host socket. Improper power sequencing may cause a damaging latchup condition. 2.3 Using the PCCswap Switch PCCextend 140 includes two PCCswap switches which can be used to momentarily interrupt the CCD1# and CCD2# signals. The switches are located on both sides of the termination area. The PCCswap switch can interrupt the card detect signals (CCD1# and CCD2#) to simulate a card removal/insertion cycle. When a card is inserted, #CCD1 and #CCD2 may be momentarily interrupted by pressing the PCCswitch. To test the operation of the PCCswap switch, be M Sycard Technology
6 Page 4 PCCextend 140 User s Manual sure that the PC Card Software drivers are loaded. Momentarily press both PCCswap switches simultaneously. Most software drivers will issue a removal beep followed by an insertion beep. The host socket controller may remove power when it detects that card detects have been removed. 2.4 Series Termination Area A series termination area located between the test points and the card connector allows access to all PC Card signals. A series of surface mount pads allows the user to add series resistors to any signal. The SMT pads are arranged as follows: When shipped from the factory, the resistor pads are shorted with PCB traces. In order to insert series resistor, these traces must be cut prior to soldering the resistor to the board. Figures and illustrate the termination areas located on both sides of the PCCextend board. Use this guide when making modifications to the board since the silkscreen designations may be difficult to read. SW1 RUN# R1 R10 C D2# AD29 R2 R13 AD30 AD26 R3 R16 STSCHG AD24 R5 R20 AD22 R7 R24 AD20 R9 R28 R12 R32 AD17 R15 R36 R18 R40 STO P# R22 R44 RFU3 AD14 R26 R47 AD15 AD11 R30 R50 R34 R53 AD8 AD5 R38 R56 AD6 AD1 R42 R58 AD2 SW2 Figure Termination Area - Component Side Sycard Technology M
7 PCCextend 140 User s Manual Page 5 AD31 AD28 AD19 R19 R4 R23 R6 R27 R8 R31 R11 R35 R14 R39 R17 R43 R21 RFU1 AD27 AD25 AD23 AD21 AD18 R46 R25 DEVSEL# R49 R29 VPP1 R52 R33 AD16 R55 R37 AD13 R57 R41 AD12 AD10 R59 R45 AD9 RFU2 R60 R48 AD7 AD4 R61 R51 AD3 CD1# R62 R54 AD0 Figure Termination Area - Solder Side 2.5 PCCextend Current Protection Device A resettable fuse protects the host from excessive current consumption from the card. Located at V1, a Raychem PolySwitch resettable fuse provides low resistance operation up to 900mA Bit/Zoomed Video Overlay Included with the PCCextend 140 is a plastic overlay with 16-bit and Zoomed Video signal description. The overlay is designed to be placed over the two 34 pin test point areas. 2.7 Optional Hewlett Packard Logic Analyzer Adapter An optional HP Logic analyzer adapter (PCCextend 145) facilitates connection to the 16500, 1650 and 1660 series of logic analyzers. Contact Sycard Technology for pricing and availability. M Sycard Technology
8 Page 6 PCCextend 140 User s Manual Appendix A. PCCextend 140 Schematic Sycard Technology M
9 AD[0..31] VCC VPP1 RFU1 RN# AD[0..31] AD0 AD1 AD3 AD5 AD7 AD9 AD11 AD12 AD14 AD18 AD20 AD21 AD22 AD23 AD24 AD25 AD26 AD27 AD29 RN# VPP1 RFU P1 35 CAD0 CCD1# 36 CAD1 CAD2 37 CAD3 CAD4 38 CAD5 CAD6 39 CAD7 RFU 40 C CAD8 41 CAD9 CAD10 42 CAD11 C 43 CAD12 CAD13 44 CAD14 CAD15 45 C CAD16 46 C RFU 47 C C 48 C C 49 C CDEVSL# 50 VCC VCC 51 VPP1 52 C C 53 C C 54 C CAD17 55 CAD18 CAD19 56 CAD20 C 57 CAD21 C 58 CAD22 C 59 CAD23 C 60 CAD24 C 61 CAD25 C 62 CAD26 CSTSCHG 63 CAD27 CAD28 64 CAD29 CAD30 65 RFU CAD31 66 CRN# CCD2# CARDBUS CD1# RFU2 RFU3 DEVSL# STSCHG CD2# AD2 AD4 AD6 AD8 AD10 AD13 AD15 AD16 AD17 AD19 AD28 AD30 AD31 RFU2 SW2 PUSHBUTTON RFU3 DEVSL# STSCHG CD1A# VCC CD1A# VCC VCC RN# AD29 AD26 AD24 AD22 AD20 AD14 AD11 AD5 AD1 CD2# AD30 STSCHG AD17 RFU3 AD15 AD8 AD6 AD J X 17 J X 17 RFU1 AD27 AD25 AD23 AD21 AD18 VPP1 AD12 AD9 AD7 AD3 AD0 AD31 AD28 AD19 DEVSL# AD16 AD13 AD10 RFU2 AD4 CD1# HOST SIDE CONNECTOR SW1 CD2A# CD2A# PUSHBUTTON FILE=PCCEXT1.S31 Sycard Technology Title PCCextend Host Connector Size Document Number REV B B Date: April 2, 1996 Sheet 1 of 4
10 POWER TRACE VPP1 RFU1 RFU2 RFU3 RN# STSCHG VPP1 RFU1 RFU2 RFU3 RN# STSCHG R34 R37 R12 R20 R22 R33 R15 R18 R29 R25 R21 R4 R60 R44 R1 R16 C C C C C C C C CVPP1 C C CRFU1 CRFU2 CRFU3 CRN# CSTSCHG C C C C C C C C CVPP1 C C CRFU1 CRFU2 CRFU3 CRN# CSTSCHG AD0 AD1 AD2 AD3 AD4 AD5 AD6 AD7 AD8 AD9 AD10 AD11 AD12 AD13 AD14 AD15 R54 R42 R58 R51 R61 R38 R56 R48 R53 R45 R59 R30 R41 R57 R26 R47 CAD0 CAD1 CAD2 CAD3 CAD4 CAD5 CAD6 CAD7 CAD8 CAD9 CAD10 CAD11 CAD12 CAD13 CAD14 CAD15 AD16 AD17 AD18 AD19 AD20 AD21 AD22 AD23 AD24 AD25 AD26 AD27 AD28 AD29 AD30 AD31 R55 R32 R17 R39 R9 R14 R7 R11 R5 R8 R3 R6 R23 R2 R13 R19 CAD[0..31] CAD16 CAD17 CAD18 CAD19 CAD20 CAD21 CAD22 CAD23 CAD24 CAD25 CAD26 CAD27 CAD28 CAD29 CAD30 CAD31 CAD[0..31] AD[0..31] FILE=PCCEXT2.S31 AD[0..31] Sycard Technology Title PCCextend SERIES RESISTOR Size Document Number REV B B Date: April 2, 1996 Sheet 2 of 4
11 CD1A# CD1A# R62 CCD1# CCD1# R50 C C R28 C C R52 C C R40 C C DEVSL# DEVSL# R49 CDEVSL# CDEVSL# POWER TRACE R46 C C R36 C C R43 C C R35 C C R24 C C R31 C C R27 C C CD2A# CD2A# R10 CCD2# CCD2# Sycard Technology FILE=PCCEXT3.S31 Title PCCextend SERIES RESISTOR 2 Size Document Number REV B B Date: April 2, 1996 Sheet 3 of 4
12 5V LED R63 D2 D1 110 ohm LED 3.3V ZENER R ohm D3 LED POWER LED CAD[0..31] CAD[0..31] VCC CVPP1 C V1 CPD CVPP1 C JP1 JUMPER JP2 JUMPER C3 0.1uF C4 0.1uF C6 0.1uF C5 0.1uF C7 10uF C8 10uF VCC2 C C C C C C CVPP1 C C C CRFU1 CRN# CAD0 CAD1 CAD3 CAD5 CAD7 CAD9 CAD11 CAD12 CAD14 VCC2 CAD18 CAD20 CAD21 CAD22 CAD23 CAD24 CAD25 CAD26 CAD27 CAD29 C C C C C C CVPP1 C C C CRFU P2 35 CAD0 CCD1# 36 CAD1 CAD2 37 CAD3 CAD4 38 CAD5 CAD6 39 CAD7 RFU 40 C CAD8 41 CAD9 CAD10 42 CAD11 C 43 CAD12 CAD13 44 CAD14 CAD15 45 C CAD16 46 C RFU 47 C C 48 C C 49 C CDEVSL# 50 VCC VCC 51 VPP1 52 C C 53 C C 54 C CAD17 55 CAD18 CAD19 56 CAD20 C 57 CAD21 C 58 CAD22 C 59 CAD23 C 60 CAD24 C 61 CAD25 C 62 CAD26 CSTSCHG 63 CAD27 CAD28 64 CAD29 CAD30 65 RFU CAD31 66 CRN# CCD2# CARDBUS CCD1# CRFU2 C CRFU3 C C CDEVSL# VCC2 C C C C C C C C C CSTSCHG CCD2# CAD2 CAD4 CAD6 CAD8 CAD10 CAD13 CAD15 CAD16 CAD17 CAD19 CAD28 CAD30 CAD31 CCD1# CRFU2 C CRFU3 C C CDEVSL# C C C C C C C C C CSTSCHG CCD2# SOCKET SIDE CONNECTOR FILE=PCCEXT4.S31 Sycard Technology Title PCCextend Card Side Size Document Number REV B B Date: April 2, 1996 Sheet 4 of 4
CF extend 160A & CF extend 160B CompactFlash Extender Cards User s Manual
CF extend 160A & CF extend 160B CompactFlash Extender Cards User s Manual Preliminary M200036-03 February 2002 Sycard Technology 1180-F Miraloma Way Sunnyvale, CA 94085 (408) 749-0130 (408) 749-1323 fax
CF extend 166/167 CompactFlash -to-pc Card Extender/Adapter User s Manual
CF extend 66/67 CompactFlash -to-pc Card Extender/Adapter User s Manual Preliminary M200055-00 May 2000 Sycard Technology 80-F Miraloma Way Sunnyvale, CA 94086 (408) 749-030 (408) 749-323 FAX http://www.sycard.com
Sycard Technology Product Catalog. Table of contents
C Sycard Technology Product Catalog Table of contents 16-bit PC Card Development Tools 5 Extender Cards/Socket Savers 5 16-bit PC Card Prototype Boards 7 16-bit PC Card Test Tools 2 Manufacturing PC Card
QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 740 TRACKER/SEQUENCER DEMO BOARD
DESCRIPTION QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 740 LTC2922 Demonstration circuit 740 is a tracker/sequencer demo board featuring the LTC2922 that monitors up to five external power supplies and
S Application Circuit with SATA Input/Output S Eye Diagram Test Circuit with SMA Inputs/ Outputs
19-4953; Rev 0; 9/09 MAX4951AE Evaluation Kit General Description The MAX4951AE evaluation kit (EV kit) provides a proven design to evaluate the MAX4951AE dual-channel buffer. The EV kit contains four
Neo900 Hackerbus PRELIMINARY SUBJECT TO CHANGE WITHOUT FURTHER NOTICE
Neo900 Hackerbus PRELIMINARY SUBJECT TO CHANGE WITHOUT FURTHER NOTICE Jörg Reisenweber, Werner Almesberger February 25, 2015 The Hackerbus is an interface that allows user-provided circuits to connect
BUILDING YOUR KIT. For the Toadstool Mega328.
BUILDING YOUR KIT For the Toadstool Mega328 www.crash-bang.com @crashbang_proto This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License. Congratulations! You re
REMOTE LOGIC I/O [INPUT/OUTPUT] PCB (LOGIO) Part No. 46S For use on MicroTrac DSD Local Area Network
![REMOTE LOGIC I/O [INPUT/OUTPUT] PCB (LOGIO) Part No. 46S For use on MicroTrac DSD Local Area Network](/thumbs/77/75979287.jpg "REMOTE LOGIC I/O [INPUT/OUTPUT] PCB (LOGIO) Part No. 46S For use on MicroTrac DSD Local Area Network")
RD 798-10 REMOTE DEVICE USER REFERENCE SHEET FOR REMOTE LOGIC I/O [INPUT/OUTPUT] PCB (LOGIO) Part No. 46S02798-0010 For use on MicroTrac DSD Local Area Network Effective 6/18/90 1 CONTENTS INTRODUCTION...3
S Proven PCB Layout S Fully Assembled and Tested. Maxim Integrated Products 1
19-5059; Rev 1; 4/10 General Description The MAX4951B evaluation kit (EV kit) provides a proven design to evaluate the MAX4951BE dual-channel redriver. The EV kit contains four sections: application circuit,
MX Educational Target User Manual
MX Educational Target User Manual Revision History Date Description Initial release. Table of Contents 1. Introduction... 4 1.1. Module Models... 4 1.2. Package Contents... 4 1.3. Key Hardware Features...
DEMO9S08SH8/SG8 Demonstration Board for Freescale MC9S08SH8/SG8
DOC-0398-010, REV A DEMO9S08SH8/SG8 Demonstration Board for Freescale MC9S08SH8/SG8 Axiom Manufacturing 2813 Industrial Lane Garland, TX 75041 Email: Sales@axman.com Web: http://www.axman.com CONTENTS
JU1 JU6, JU15 JU20. Maxim Integrated Products 1
9-9; Rev 0; /0 MAX9 Evaluation Kit General Description The MAX9 evaluation kit (EV kit) contains a flowthrough low-voltage differential signaling (LVDS) quad differential line driver (MAX9) and receiver
Setting new Standards. Active Extenders PCIAX CPCI64. Hot Swap PCI Bus Extender Boards PCI. User Manual Revision 5.
Setting new Standards Active Extenders PCIAX CPCI64 Hot Swap PCI Bus Extender Boards PCI User Manual Revision 5.3 September, 2000 1439 Torrington Court San Jose, CA 95120 Tel: (408) 268-4145 Fax: (408)
S IEEE 802.3af/at-Compliant PSE Circuit. Maxim Integrated Products 1
19-5740; Rev 0; 1/11 MAX5971A Evaluation Kit General Description The MAX5971A evaluation kit (EV kit) is a fully assembled and tested surface-mount circuit board featuring an Ethernet single-port power-sourcing
Digilab 2E Reference Manual
Digilent 2E System Board Reference Manual www.digilentinc.com Revision: February 8, 2005 246 East Main Pullman, WA 99163 (509) 334 6306 Voice and Fax Digilab 2E Reference Manual Overview The Digilab 2E
ANC-8000 / ANC-9000 LCC/PGA/PCC/QFP to Wire Wrap Adapter Series. Antona Corporation, Los Angeles, Ca.
Rev. H $ 5.00 ANC-8000 / ANC-9000 LCC/PGA/PCC/QFP to Wire Wrap Adapter Series Antona Corporation, Los Angeles, Ca. 1643 1/2 Westwood Blvd., L.A., CA. 90024-5603 Tel:(310) 473-8995 ***** BEFORE INSTALLING
GRAVITECH GROUP
GRAVITECH.US uresearch GRAVITECH GROUP Description The I2C-TMP board is a 6-pin CMOS 12- bit digital temperature sensor device using I 2 C bus. There are no external components required. Only two signal
Digilab 2 XL Reference Manual
125 SE High Street Pullman, WA 99163 (509) 334 6306 (Voice and Fax) www.digilentinc.com PRELIMINARY Digilab 2 XL Reference Manual Revision: May 7, 2002 Overview The Digilab 2 XL (D2XL) development board
Universal Keying Adapter 3+
Universal Keying Adapter 3+ The Universal Keying Adapter Version 3+ kit will allow you to key nearly any transmitter or transceiver with a straight key, electronic keyer, computer serial or parallel port
Transcendent Frequency Counter
Transcendent Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and operate this frequency counter KIT. Features: The transcendent counter has two input channels
DEMO9S08SH32/SG32 Demonstration Board for Freescale MC9S08SH32/SG32
DOC-0421-010, REV A DEMO9S08SH32/SG32 Demonstration Board for Freescale MC9S08SH32/SG32 Axiom Manufacturing 2813 Industrial Lane Garland, TX 75041 Email: Sales@axman.com Web: http://www.axman.com CONTENTS
Active Extenders MODELS PC/AT150 & PC/AT200. Hot Swap PC/AT Bus Extender Boards. User Manual. Revision 8.1. March 30, 1999.
Active Extenders MODELS PC/AT150 & PC/AT200 Hot Swap PC/AT Bus Extender Boards User Manual Revision 8.1 March 30, 1999 Catalyst Enterprises, Inc. 1439 Torrington Court San Jose, CA 95120 (408) 268-4145
NMEA Expander. Operation And. Installation Manual
NMEA Expander Operation And Installation Manual XXXXXX_20130331 Revision B0 Syberg Maritim 1. OPERATION AND CONFIGURATION... 3 SYSTEM SUMMARY... 3 INPUT POWER SUPPLY, D CONFIGURATION... 4 INPUT POWER SUPPLY,
Digilab 2 Reference Manual
125 SE High Street Pullman, WA 99163 (509) 334 6306 (Voice and Fax) www.digilentinc.com PRELIMINARY Digilab 2 Reference Manual Revision: November 19, 2001 Overview The Digilab 2 (D2) development board
IMU Axis Gyro Evaluation Board Application Note
IMU-3000 3-Axis Gyro Evaluation Board Application Note A printed copy of this document is NOT UNDER REVISION CONTROL unless it is dated and stamped in red ink as, REVISION CONTROLLED COPY. InvenSense,
BMC056. Utility Buttons Last updated
BMC056. Utility Buttons Last updated -0-209 If you have any questions, or need help trouble shooting, please e-mail Michael@Bartonmusicalcircuits.com I Controls/Inputs/Outputs II Schematic III Construction
Maxim Integrated Products 1
19-4581; Rev 0; 4/09 MAX4989 Evaluation Kit General Description The MAX4989 evaluation kit (EV kit) provides a proven design to evaluate the MAX4989 Hi-Speed 2-of-4 USB 2.0 crosspoint switch. The EV kit
S Complete 2:1 VGA Multiplexer S VGA Connections and Power S LED Indicators for Switch Connections S VGA Inputs/Outputs S Fully Assembled and Tested
19-5030; Rev 0; 10/09 MAX4885AE Evaluation Kit General Description The MAX4885AE evaluation kit (EV kit) is a fully assembled and tested circuit board that evaluates the MAX4885AE VGA 2:1 multiplexer.
MAX6642 Evaluation System/Evaluation Kit
19-3417; Rev 0; 9/04 MAX6642 Evaluation System/Evaluation Kit General Description The MAX6642 evaluation kit (EV kit) is an assembled and tested PC board with a mounted MAX6642. The EV kit allows full
S One SATA Host Connector S Two SATA Device Connectors
19-5166; Rev 0; 2/10 MAX4986 Evaluation Kit General Description The MAX4986 evaluation kit (EV kit) provides a proven design to evaluate the MAX4986 SAS/SATA 2:1/1:2 multiplexer/demultiplexer. The EV kit
Rapid28iXL PIC Prototyping PCB User Manual
Description Features This is a PCB designed to facilitate the rapid prototyping of a device based on a 28 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of
DS-MPE-GPIO. PCIe MiniCard Digital I/O Module with FPGA. Rev A.1 June 2015
DS-MPE-GPIO PCIe MiniCard Digital I/O Module with FPGA Rev A.1 June 2015 Revision Date Comment A.0 8/27/2014 Initial release A.1 6/17/15 Corrected pin out information FOR TECHNICAL SUPPORT PLEASE CONTACT:
Revision: 5/7/ E Main Suite D Pullman, WA (509) Voice and Fax. Power jack 5-9VDC. Serial Port. Parallel Port
Digilent Digilab 2 Reference Manual www.digilentinc.com Revision: 5/7/02 215 E Main Suite D Pullman, WA 99163 (509) 334 6306 Voice and Fax Overview The Digilab 2 development board (the D2) features the
Maxim Integrated Products 1
19-3717; Rev 1; 11/05 MAX1179 Evaluation Kit General Description The MAX1179 evaluation kit (EV kit) is an assembled and tested circuit board that demonstrates the MAX1179 analog-to-digital converter.
Rapid40iXL PIC Prototyping PCB User Manual
Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping
PedalSync. 9 Switches MV-62. Chip. Module. and
PedalSync 9 Switches MV-62 Chip and Module PedalSync 9 Switches chip MV-62 is designed for pedalboard switching controls using the extremely quiet PedalSync MV-57 ReMute Relay Bypass system. MV-62 works
N8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B.
N8VEM S-100 BACKPLANE VERSION 04 MAY 3, 2015 J.B. Background. This board is a copy of Andrew Lynch s Version 03 board (with 8 slots) but with added features. Added features: 9 SLOT Active Termination (copied
RHODEUS PANEL I/O BOARD
RHODEUS PANEL I/O BOARD User Manual Revision A April 2011 Revision Date Comment A 4/11/11 Initial Release FOR TECHNICAL SUPPORT PLEASE CONTACT: Copyright 2011 Diamond Systems Corporation 555 Ellis Street
LPT-to-I2C SE. Hardware Reference Guide.
LPT-to-I2C SE Hardware Reference Guide http://www.i2ctools.com/ November 1, 2008 Information provided in this document is solely for use with the LPT-to-I2C SE product from SB Solutions, Inc. SB Solutions,
+Denotes lead-free and RoHS-compliant.
19-3107; Rev 0; 12/07 MAX1493 Evaluation Kit General Description The MAX1493 is a low-power, 4.5-digit analog-to-digital converter (ADC) with integrated liquid-crystal display (LCD) drivers. The MAX1493
MUSIC SERVER SERVICE MANUAL CONTENTS
MUSIC SERVER CONTENTS Performance Specifications... 2 Notes... 2 Safety Information... 2 Rear Panel... 3 Section Location... 3 Block Diagram... 4 Interconnection Diagram... 5 Front Panel Schematic and
CAT310DB1 DEMONSTRATION BOARD FOR CAT CHANNEL LED DRIVER
APPLICATION NOTE WWW.CATALYST-SEMICONDUCTOR.COM CAT30DB DEMONSTRATION BOARD FOR CAT30 0 CHANNEL LED DRIVER Denisa Stefan, Application Engineer Cornel Rotaru, Application Engineer. INTRODUCTION This document
DYNAMIC ENGINEERING 435 Park Dr., Ben Lomond, Calif Fax Est
DYNAMIC ENGINEERING 435 Park Dr., Ben Lomond, Calif. 95005 831-336-8891 Fax 831-336-3840 http://www.dyneng.com sales@dyneng.com Est. 1988 User Manual c P C I 2 P M C cpci 1 Slot PMC Compatible Carrier
Mini4 Dual Sonar Interface Board (P/N xxx) User s Manual And Troubleshooting Guide
Mini4 Dual Sonar Interface Board (P/N 201630-xxx) User s Manual And Troubleshooting Guide February 23, 2009 Rev B Moog Components Group Springfield Operations 750 West Sproul Road Springfield, PA 19064
MAX5097A Evaluation Kit. Evaluates: MAX5097A
19-0718; Rev 0; 1/07 MAX5097A Evaluation Kit General Description The MAX5097A evaluation kit (EV kit) demonstrates the MAX5097A in a standard application circuit demonstrating high efficiency. The EV kit
KSZ9692PB User Guide Brief
KSZ9692PB User Guide Brief KSZ9692PB Evaluation Platform Rev 2.0 General Description The KSZ9692PB Evaluation Platform accelerates product time-to-market by providing a hardware platform for proof-of-concept,
DIO-1616B-PE. Features. Packing List. PCI Express-compliant Opto-isolated Digital I/O Board with On-board power supply DIO-1616B-PE 1. Ver.1.
PCI Express-compliant Opto-isolated Digital I/O Board with On-board DIO-1616B-PE Features Opto-coupler isolated input (support current sink output) and opto-coupler isolated open-collector output (current
DYNAMIC ENGINEERING 150 DuBois St. Suite 3, Santa Cruz, Calif Fax Est.
DYNAMIC ENGINEERING 150 DuBois St. Suite 3, Santa Cruz, Calif. 95060 831-457-8891 Fax 831-457-4793 http://www.dyneng.com sales@dyneng.com Est. 1988 User Manual PCI2PMC PCI Single Slot PMC Compatible Carrier
SRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
Maxim Integrated Products 1
19-3093; Rev 0; 12/03 MAX3942 Evaluation Kit General Description The MAX3942 evaluation kit (EV kit) is an assembled demonstration board that provides electrical evaluation of the MAX3942 10.7Gbps modulator
November 2000 Mixed-Signal Products SLOU086
User s Guide November 2000 Mixed-Signal Products SLOU086 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or
+Denotes lead-free and RoHS compliant. C38 C43, C62, C64, C65, C66, C68, C70, C72, C73, C74, C76 C44 C49, C67, C75 C63, C69, C71, C77
19-4354; Rev 0; 10/08 MAX17108 Evaluation Kit General Description The MAX17108 evaluation kit (EV kit) is a fully assembled and tested surface-mount PCB that evaluates the MAX17108 10-channel, high-voltage
MAX4951C Evaluation Kit Evaluates: MAX4951C
19-5944; Rev 0; 6/11 MAX4951C Evaluation Kit General Description The MAX4951C evaluation kit (EV kit) provides a proven design to evaluate the MAX4951C dual-channel buffer. The EV kit contains four sections:
DAQ system assembly and operation
DAQ system assembly and operation Vladimir Dergachev 2011-04-15 1 DAQ system overview Figure 1: Assembled DAQ system The assembled DAQ system 1 consists of FPGA board (Digilent Spartan 3E-1600 Development
GRAVITECH GROUP
GRAVITECH.US uresearch GRAVITECH GROUP Description The I2C-ADC board is a 14-pin CMOS device that provides 8-CH, 12-bit of Analog to Digital Converter (ADC) using I 2 C bus. There are no external components
Maxim Integrated Products 1
19-5229; Rev 0; 4/10 MAX14885E Evaluation Kit General Description The MAX14885E evaluation kit (EV kit) is a fully assembled and tested surface-mount PCB that utilizes the MAX14885E device to implement
K8099 NIXIE CLOCK. * optional enclosure TKOK19 (black) - TKOK17 (white) ** optional plexiglass enlcosure B8099 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 230 + 74 Difficulty level: beginner 1 2 3 4 5 advanced NIXIE CLOCK K8099 ** * A unique combination of both vintage and modern electronics ILLUSTRATED ASSEMBLY MANUAL H8099IP-1 * optional
GRBL SHIELD FOR ARDUINO UNO USER MANUAL
GRBL SHIELD FOR ARDUINO UNO USER MANUAL YRCNC 2017 Introduction Thanks for supporting us! Hope you will have many hours of fun using this shield and that plenty hours of issueless cutting! The main features
University of Florida EEL 4744 Drs. Eric M. Schwartz, Karl Gugel & Tao Li Department of Electrical and Computer Engineering
Page 1/9 Revision 1 OBJECTIVES In this document you will learn how to solder and to debug a board as you are building it. REQUIRED MATERIALS Website documents o UF 68HC12 Development Board Manual (board
Maxim Integrated Products 1
9-366; Rev ; 2/06 General Description The MAX8727 evaluation kit (EV kit) is a fully assembled and tested surface-mount circuit board that contains a pulse-width-modulated (PWM) step-up DC-DC converter.
Skywire BeagleBone Black Cape Data Sheet
Skywire BeagleBone Black Cape Data Sheet NimbeLink Corp Updated: January 2018 PN 30122 rev 2 NimbeLink Corp. 2016. All rights reserved. 1 Table of Contents Table of Contents 2 Introduction 3 Overview 3
7I44 MANUAL 8 CHANNEL RS-422 INTERFACE
7I44 MANUAL 8 CHANNEL RS-422 INTERFACE V1.1 This page intentionally almost blank Table of Contents GENERAL.......................................................... 1 DESCRIPTION.................................................
ATLD10A5-D EV1.0 Evaluation Board for ATLD10A5-D 10A High Efficiency Laser Controller ATLD10A5-D Evaluation Board Rev. 1.0
ATLD0A5-D EV.0 Evaluation Board for ATLD0A5-D 0A High Efficiency Laser Controller ATLD0A5-D Evaluation Board Rev..0 Figure ATLD0A5-D EV.0 Photo INTORDUCTION The ATLD0A5-D is an electronic module designed
Rapid40i PIC Prototyping PCB User Manual
Description This is a PCB designed to facilitate the rapid prototyping of a device based on a 40 pin Microchip PIC microcontroller. To allow users to focus on their application, we take care of key housekeeping
CPCI-ASIO4 CAN - RS-232, RS-422, RS-485
CPCI-ASIO4 CAN - RS-232, RS-422, RS-485 or TTY-Interface Hardware Manual Document file: I:\texte\Doku\MANUALS\CPCI\ASIO4\Englisch\ASIO4-11H.en9 Date of print: 28.07.2004 PCB-version: CPCI-ASIO4 Rev. 1.0
RPG 100 EVALUATION BOARD RPG100-TB(MB) User's manual
HM-RAE102-0312 RPG 100 EVALUATION BOARD RPG100-TB(MB) User's manual REV. 02 26/09/2003 revised http://www.fdk.co.jp Contents 1. RPG100 Evaluation Board composition Models: RPG100-TB and RPG100-MB 2. Descriptions
The FED PIC Flex 2 Development Boards
The FED PIC Flex 2 Development Boards THE FED PIC Flex Development board offers a host for 28 or 40 pin devices and includes LED's, switches, transistor switches, USB interface, serial port, support circuitry,
Achieving EMV Electrical Compliance with the Teridian 73S8024RN
August 2005 Achieving EMV Electrical Compliance with the Teridian 1 Introduction This application note highlights particular testing considerations required to achieve compliance for payment systems smart
MAX14579E Evaluation Kit Evaluates: MAX14579E/MAX14579AE
19-5995; Rev 0; 8/11 General Description The MAX14579E evaluation kit (EV kit) provides a proven design to evaluate the MAX14579E headset detection IC. The EV kit is designed to demonstrate the IC s headset
PCCtest 450/460 Zoomed Video Software User s Manual
PCCtest 450/460 Zoomed Video Software User s Manual M200022-09 January 2005 Sycard Technology 1180-F Miraloma Way Sunnyvale, CA 94085 (408) 749-0130 (408) 749-1323 FAX http://www.sycard.com PCCtest 450/460
for Summit Analyzers Installation and Usage Manual
Protocol Solutions Group PCI Express 2.0 Mid-Bus Probe for Summit Analyzers Installation and Usage Manual Manual Version 1.1 Generated on: 2/7/2018 6:25 PM Document Disclaimer The information contained
xpico 110 Wired Device Server Module Evaluation Kit User Guide
xpico 110 Wired Device Server Module Evaluation Kit User Guide Part Number 900-788-R Revision A April 2017 Intellectual Property 2017 Lantronix, Inc. All rights reserved. No part of the contents of this
2001 Mixed-Signal Products SLOU091A
User s Guide 2001 Mixed-Signal Products SLOU091A Preface How to Use This Manual This document contains the following chapters: Chapter 1 Introduction Chapter 2 Operation Related Documentation From Texas
CDN502 HIGH DENSITY I/O ADAPTER USER GUIDE
CDN502 HIGH DENSITY I/O ADAPTER USER GUIDE 13050201 (c) Copyright DIP Inc., 1996 DIP Inc. P.O. Box 9550 MORENO VALLEY, CA 92303 714-924-1730 CONTENTS DN502 PRODUCT OVERVIEW 1 DN502 INSTALLATION 1 POWER
CDN503 HIGH DENSITY I/O ADAPTER USER GUIDE
CDN503 HIGH DENSITY I/O ADAPTER USER GUIDE 13050301 (c) Copyright DIP Inc., 1996 DIP Inc. P.O. Box 9550 MORENO VALLEY, CA 92303 714-924-1730 CONTENTS DN503 PRODUCT OVERVIEW 1 DN503 INSTALLATION 1 POWER
MAX17116Q Evaluation Kit Evaluates: MAX17116 in a 24-Pin TQFN Package
19-5846; Rev 0; 5/11 MAX17116Q Evaluation Kit General Description The MAX17116Q evaluation kit (EV kit) is a fully assembled and tested surface-mount PCB that evaluates the MAX17116 dual-output DC/DC power
Celadon, Inc. TRX Series Infrared Remote and Receiver Assembly and Operation Instruction Manual
Celadon, Inc. TRX Series Infrared Remote and Receiver Assembly and Operation Instruction Manual REV 2.1 COPYRIGHT 2001 I. Introduction Thank you for purchasing your infrared remote control transmitter
Mini4 Data Mux User s Manual. ( xxx) And. Troubleshooting Guide
Mini4 Data Mux User s Manual And Troubleshooting Guide June 7, 2010 Rev B Moog Components Group 750 West Sproul Road, Springfield, PA 19064 E-Mail: URL: Tel: 610-328-4000 Fax: TABLE OF CONTENTS 1 Mini4
Ultimate LPF kit: Relay-switched LPF kit
Ultimate LPF kit: Relay-switched LPF kit PCB Revision 4 1. Introduction Thank you for purchasing the QRP Labs relay-switched low-pass filter (LPF) kit. This kit is designed to complement the Ultimate3
NewScope-7B Operating Manual
2016 SIMMCONN Labs, LLC All rights reserved NewScope-7B Operating Manual Preliminary May 13, 2017 NewScope-7B Operating Manual 1 Introduction... 3 1.1 Kit compatibility... 3 2 Initial Inspection... 4 3
Exclusive 2.5 GHz Frequency Counter
Exclusive 2.5 GHz Frequency Counter with blue 2 x 16 LCD display This manual will guide you how to assemble, test and tune this frequency counter KIT. Features: Frequency range from 5 MHz to 2.5GHz Factory
GLiPIC Ver C Assembly manual Ver 1.0
GLiPIC Ver C Assembly manual Ver 1.0 Last Rev 1.1 Oct 30, 2001 Author: Ranjit Diol Disclaimer and Terms of Agreement As with any kit, only the individual parts supplied are guaranteed against defects and
DisplayPort * Interposer Test Fixture
DisplayPort * Interposer Test Fixture DPI-P2RP / Plug to Receptacle Fixture: Features: The Interposer allows connection of test equipment to the DisplayPort interface signals. The fixture has been designed
DYNAMIC ENGINEERING 150 DuBois St. Suite C, Santa Cruz, Calif Fax Est.
DYNAMIC ENGINEERING 150 DuBois St. Suite C, Santa Cruz, Calif. 95060 831-457-8891 Fax 831-457-4793 http://www.dyneng.com sales@dyneng.com Est. 1988 User Manual PCI2PMC PCI Single Slot PMC Compatible Carrier
High Power (15W + 15W) Stereo Amplifier
High Power (15W + 15W) Stereo Amplifier Build Instructions Issue 1.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit
TRAKIT-25P. Printings. Version 1.00: 10/03/01 Version 2.00: 01/20/03 Version 2.10: 01/19/04
TRAKIT-25P Printings Version 1.00: 10/03/01 Version 2.00: 01/20/03 Version 2.10: 01/19/04 TABLE OF CONTENTS SPECIFICATIONS... 1 1.0 GENERAL DESCRIPTION... 2 1.1 Description... 2 1.2 Capabilities and Features...
User Guide for the Pericom PI7C8150 Reference board By Glenn Sanders
2789027890278902278902789027890227890278902789022789027890278902278902 Introduction The Pericom PI7C80 PCI-to-PCI bridge evaluation board demonstrates the bridge and allows testing of key features either
Building the FlipChip Tester
Building the FlipChip Tester 1. Assembly of the Core Board You will need a fine low-wattage soldering iron and a Voltmeter. Take your time to solder the components on the Core Board. Better to spend a
DYNAMIC ENGINEERING 150 DuBois St. Suite 3, Santa Cruz Ca Fax Est
DYNAMIC ENGINEERING 150 DuBois St. Suite 3, Santa Cruz Ca. 95060 831-457-8891 Fax 831-457-4793 sales@dyneng.com www.dyneng.com Est. 1988 User Manual CPCI-J2-SCSI CPCI User IO for 3U J2 SCSI connector Rear
DSP-232 Upgrade Kit A.06113
DSP-232 Upgrade Kit A.063 Installation and Operation Manual Rev. 2.0 WARRANTY WHO IS COVERED WHAT WE WILL DO WHAT YOU MUST DO WHAT IS NOT COVERED SERVICE WARRANTY HOW TO CONTACT TIMEWAVE TIMEWAVE TECHNOLOGY
ANC Series RS-422 Serial Communications Adapter
Rev. B $ 5.00 ANC - 6000 Series RS-422 Serial Communications Adapter Antona Corporation, Los Angeles, CA Antona Corporation (818)783-4299 FAX (818)783-4216 1 Antona Corporation Copyright Copyright (c)
XR32220 Evaluation Board User s Manual
XR32220 Evaluation Board User s Manual Introduction Exar s XR32220 EVB evaluation board provides a platform on which to examine the features and performance of the XR32220 2-Driver/2-Receiver RS-232 serial
OEM-ORP ORP. Reads mV mV. Range. 1 reading every 420ms. Response time. Any type & brand. Supported probes. Single point.
V 2.3 Revised /23/18 OEM-ORP Embedded ORP Circuit Reads Range Response time ORP -19.9mV 19.9mV 1 reading every 420ms Supported probes Calibration Temp compensation Data protocol Default I 2 C address Operating
isppac-powr607 Evaluation Board User s Guide
isppac-powr0 Evaluation Board User s Guide May 00 Revision: EB8_0.0 isppac-powr0 Introduction Lattice Semiconductor s Power Manager II isppac -POWR0 device simplifies power supply design by integrating
Symphony SoundBite Reference Manual
Symphony SoundBite Reference Manual Document Number: SNDBITERM Rev. 2.0 09/2008 Contents Section 1, Introduction page 2 Section 2, Functional Blocks page 3 Section 3, Configuration and Connections page
OPMM-1616-XT. PC/104 I/O Module with Optoisolated inputs and Relay Outputs. Rev 1.0 September 2010
init OPMM-1616-XT PC/104 I/O Module with Optoisolated inputs and Relay Outputs Rev 1.0 September 2010 Revision Date Comment 1.0 9/26/2010 first release FOR TECHNICAL SUPPORT PLEASE CONTACT: Copyright 2010
User's Manual MC672/MC672A INPUT/OUTPUT BOARD. Features DEVICE CODE:
Features On board opto-isolated RS485 interface. 16 dry contact inputs, each with a LED for status indication. (common ground) All inputs have owner state changed timeout setting for improved input noise
D115 The Fast Optimal Servo Amplifier For Brush, Brushless, Voice Coil Servo Motors
D115 The Fast Optimal Servo Amplifier For Brush, Brushless, Voice Coil Servo Motors Ron Boe 5/15/2014 This user guide details the servo drives capabilities and physical interfaces. Users will be able to
VS. 4 Game Selector INSTALL GUIDE
VS. 4 Game Selector INSTALL GUIDE Each DK Selector includes the following items: 1. VS. 4 Game Selector PWB 2. 4 power cables 12, 14, 16 & 18 3. Ribbon daisy chain cable 4. Mounting feet and screws Some
CF15118 CompactFlash Carrier utilitymodules User s Manual
CompactFlash Carrier utilitymodules User s Manual BDM-610020105 Rev. A CompactFlash Carrier utilitymodules User s Manual RTD Embedded Technologies, Inc. 103 Innovation Blvd. State College, PA 16803-0906