Nevco Standard 4-Face 8 Installation Set

Transcription

1 Nevco Standard -Face 8 Installation Set Retain this manual in your permanent file.. 0/0/7-08

2 Table of ontents Instructions -0 Installation WG-077 Wired Electrical 7-07 Wireless Electrical Scoreboard ottom -0. 0/0/7-08

3 Installation Instructions Installation consists of three steps, Unpacking the Equipment, Scoreboard mounting, and Electrical onnections. e sure to read and understand all of the instructions before installing the equipment. onsult the installer s troubleshooting guide following this section for verifications each step has been installed and is working correctly.. Unpacking the Equipment Inspect the shipping container for damage. If any damage can be seen, contact the carrier immediately. arefully remove all equipment from its packing carton. o not pry against the scoreboard in any way.. Scoreboard Mounting Refer to installation prints for detailed dimensions and power requirements. For boards shipped in multiple sections: o Place the top section on the bottom section over-lapping the top face in front of the bottom face. o Open the Period door by removing two Phillips screws. o Locate the /8 - bolts shipped in the accessory package. o Install the three bolts through the inside of the top section into the threaded inserts located on the top of the bottom section using the /8 flat washers. o Tighten until the sections are fully seated together. Over-tightening can damage the scoreboard. o Pull the wires through the grommet and connect to the ILM as labeled. /8 - threaded inserts are installed in the top of the board. /8 - eyebolt can be threaded into the inserts to aid in lifting for mounting. The eyebolts can be removed after lifting or left in for a suspension mount. Mount the board securely using the pre-punched ½ holes in the top flange. For multi-section boards also secure the bottom flange. lternate ½ holes may be drilled in the flange for flexible placement of the mounting hardware. Shot clocks do not have the mounting flange, but can alternatively be mounted by the use of an SSK package. lways use good mechanical practices when mounting the scoreboard. Page

4 . Electrical onnections Service onsult the table on the installation print for power requirements for your scoreboard model. Provide for a 0% safety factor to guard against tripping of the circuit breaker under low line conditions. e sure to include any lighted signs, and message centers when sizing the supply wiring necessary to support the circuit load. The person performing the installation should be familiar with National and local electric codes. standard IE US grounded power cord is shipped with the board for attaching power. The power connection is low-profile to allow for flush mounting of signs and message centers. Signal onnections Refer to wireless receiver installation prints for receiver mounting and connections. onnect the coax input to the N marked Input. right angle N adapter can be used to allow for flush mounting of signs and message centers. The N marked Output can be used to drive other scoreboards sharing the same display data. This allows scoreboards to be daisy-chained together, or the output can be used to supply signal to accessories such as a shot clock or end of period indicator. y adding a T connector at this location, two accessories can be connected at once with up to 000 ft. of coax each. -Wire oax able (RG8/U) ll -WIRE cable ordered from Nevco is direct burial type. It has a minimum dielectric strength of 00V, and conforms to UL standard. If the wiring is buried above the freeze line, bury the cable with sand to provide drainage and prevent damage from shifting soil. Installing able onnectors The -WIRE cable that comes with your scoreboard does not have connectors attached. To install connectors on each end of the cable: Slide the insulating boot onto the cable and trim the cable as shown. Twist the outer braid in a clockwise direction so that at least / in. of the inner dielectric is bared and the braid is left flat. e sure no strands of the outer braid are touching the center conductor. Insert the center conductor into the back of the connector, feeding it into the guide hole. Push the cable as far as possible into the connector. Screw the connector onto the cable in a clockwise direction until the connector stops turning. Slip the insulating boot over the back of the connector. " 9 " Insulating boot " Page

5 . Scoreboard Systems To install a system of scoreboard displays, controls and accessories follow these guidelines. heck the website Nevco.com or contact your local sales rep to obtain other system drawings. aisy haining When all or groups of scoreboards in the facility are to operate together, installation time and costs can be saved by daisy chaining the coax cable from scoreboard to scoreboard. The diagram to the right shows this operation. Reference print 089 for more details Independent Operation When the scoreboards are to be operated together, but at other times separated and operated independently, alternate control points or cable selection switch (SS) units must be used. The diagram to the right shows this operation. Reference print 780 for more details Reference print 070 for more details Mixed Operation When independent operation is required, daisy chaining can still be used to save cost on installation. The diagram to the left shows this operation. Wireless Operation Main ourt ross-ourts Wireless systems provide the maximum flexibility by allowing the operator the ability to program groups of receivers. single receiver can drive multiple displays. See manual for the wireless device for more information. Plug a control into both jacks for Main ourt ll-on operation (shown) or plug two controls into each jack for independent cross-court operation (not shown). Page

6 WIRE TROULESHOOTING GUIE The figure to the right labels the connections from M. The chart below lists the problem that can be identified should any connection be faulty. heck the control and service manual for more detailed information. NOTE: The number that appears above a letter refers to the number of wires or conductors in the cable. ranch ircuit ontrol (coax) Supply Scoreboard Interface 8 ILM- SI -8 L Horns ETN Master igit 8 E I Horn K L 0 F river acklights Home/Guest 8 H 0 G J M Slave igit To Next igit To Next acklight To Next ETN Panel Situation Symptom onnection Solution The Scoreboard has no digits illuminated Some digits not illuminated, or non-working accessory When power is first applied the timer section does not rotate through a test pattern When power is first applied the timer section rotates through a test pattern, but then the display goes out. E heck branch circuit breaker and power connections heck connection on ILM and power supply terminal screws heck connection to first digit in timer section heck oax connections. Plug control directly into the top of the board to eliminate installed coax cable. If that works, the cable run or terminations are bad. Try the 0 Model code, see control users manual on testing. heck connections on inside of board at the SI and at the ILM Only one digit F / G / H heck 0-pin connection on river card and -pin on single segments Horn K heck -pin connection on ILM and at horn ( horns ea.) acklight channels I / J heck -pin connection on ILM and at backlight. heck instructions to see if the backlights are supposed to be ON. ll or partial ETN s not working L / M heck -pin connection from ILM to ETN and between ETN panels Page

7 Wireless Troubleshooting Guide ranch ircuit The figure to the right labels connections ( E) useful to troubleshooting. The chart below lists the problem that can be identified should any connection be faulty. heck the control and service manual for more detailed information. NOTE: The number that appears above a letter refers to the number of wires or conductors in the cable. o n t r o l dapter 0 900Mhz E Receiver (coax) Same diagram and troubleshooting from Wired Troubleshooting Guide Situation Symptom onnection Solution The Scoreboard has no digits illuminated Some digits not illuminated, or non-working accessory When power is first applied to the board the timer section does not rotate through a test pattern When power is first applied the timer section rotates through a test pattern, but then the display goes out. Receiver has No LEs illuminated during first seconds after power up Receiver LE Not ON solid Other E heck branch circuit breaker and power connections See Wired Troubleshooting Guide heck oax connections. Plug control directly into the top of the board. Try the 0 Model code, see control users manual on testing. heck branch circuit breaker and power connections If the duplex receptacle has power, but the adapter LE is OFF, replace adapter Ensure plug is fully seated in receiver jack and making good connection Replace Receiver Follow control troubleshooting procedures, wrong wireless group, etc. Receiver should be in clear line of sight from control. See Wired Troubleshooting Guide Other See Wired Troubleshooting Guide Page

8 NEVO GURNTEE To view or receive the most recent copy of the Guarantee, please visit our website, or call NEVO, Inc. 0 East Harris venue Greenville, IL - US US TOLL-FREE N TOLL-FREE International Telephone: Website: info@nevco.com NOTE: This equipment has been tested and found to comply with the limits for a lass digital device, pursuant to part of the F Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This class digital apparatus meets all requirements of the anadian Interference- ausing Equipment Regulations. et appareil numerique de la classe repecte toutes les exigences du Reglement sure le materiel brouller du anada. Page

9 Notes:. onnections to ceiling including shackles, cable or chain, anchors, etc. are furnished by and the responsibility of the others.. orner trim removed for clarity.. Weights shown do not include bottom for four face.. Weights shown do not include connections to ceiling (shackles, chain or wire rope, power winch, etc.) See note Pick Points im "" im "" Estimated Weights and Pick Points Size of Scoreboard imension "" imension "" Estimated Weight x 8 97 /" 97 /" 7 x 8 97 /" 97 /" 90 x 8 97 /" 97 /" 0 Important Note: This is not an engineered drawing. It is intended for representation purposes only. Nevco strongly suggests that you contact a professional engineer or architect familiar with the facility before the installation is attempted. They can determine if the building framework is capable of withstanding the additional forces that result from hanging a structure such as this. In addition, they will be able to verify that the bolts, framework, etc. are suitable for your particular installation. This includes, but is not limited to speakers, lights, camera systems, etc. Four Face Installation 8' enter Section Standard Scoreboards Greenville, Illinois Last EO rawing No. wg-077 rawn RS ate /7/0 Sheet of

10 imension "" Face of Scoreboard imension "" imension "E" Notes:. imension "" does not include rubber feet (adds approximately ¼"). imensions shown may vary slightly due to assembly variation.. orner trim removed for clarity. Estimated imensions Size of Scoreboard imension "" imension "" imension "E" ' x 8' 0" /8" 8" ' x 8' 7/8" 0 /8" 8" ' x 8' 7 /" /8" 8" Four Face Installation 8' enter Section Standard Scoreboards Last EO rawn ate RS /7/0 Greenville, Illinois rawing No. wg-077 Sheet of

11 /8 by / bolts, nuts, and washers supplied by Nevco Figure Figure Laterals identified by corner chamfer. etail of Foot assembly Install horizontal rails (Inst # ) Note position of horizontal rails / bolt, washers, and nuts supplied by Nevco Install feet or attach to prebuilt lower frame (Inst # ) Rubber foot supplied by Nevco /8 bolt and washer supplied by Nevco Four Face Installation 8' enter Section Standard Scoreboards Last EO Greenville, Illinois rawing No. wg-077 Sheet of rawn RS ate /7/0

12 Installation Instructions.. Install feet supplied by Nevco to the corner posts. (If there is a section of signs or message centers that go below this section, install the corner posts on top of that already assembled section.) olt as shown on sheet.. Install horizontal rails to corner posts using /8 by / bolts, washers, and nuts supplied by Nevco. (See Figure on sheet ). heck the frame to make sure it is level and square.. Install corner braces as shown in Figure on sheet.. Install scoreboards to horizontal rails using clips and /8 bolts supplied.. Install corner trim pieces as shown on sheet. 7. efore lifting, make sure all bolts are installed properly. Figure Install clips using /8 by / bolts, washers, and nuts supplied by Nevco. (ottom clips mounted to bottom side of lower horizontal rail) (Inst #) Install corner braces using / by / bolts, washers, and nuts supplied by Nevco (Inst #) etail of upper clip (bend greater than 90 deg) Top of upper lateral Lift at these points only. Use accepted lifting practices only. If not lifting or supporting directly above pick points, Nevco recommends using a spreader bar of the appropriate size. e sure to factor in the weight of additional sections, lights, speakers, etc. when determining cable or chain size. etail of lower clip (bend less than 90 deg) ottom of lower lateral Figure Four Face Installation 8' enter Section Standard Scoreboards Last EO Greenville, Illinois rawing No. wg-077 Sheet of rawn ate RS /7/0

13 Upper lip ssembled Instructions for Two Section oards Front of abinet nd olt Location TOP abinet Wiring Grommet Note overlap OTTOM abinet ⅜"- by /" olt st olt Location rd olt Location ILM (Module) Lower lip ssembled olts, washers and nuts supplied by Nevco Notes:. Set top section of cabinet on bottom section. Note that top cabinet face overlaps the bottom.. Open "Period" door and attach the sections together using the () provided /" bolts. Make sure bolts are tight.. Pull the wires up through the " grommet.. onnect wires to the ILM as labeled.. lose "period" door. Last EO rawn Four Face Installation 8' enter Section Standard Scoreboards Greenville, Illinois rawing No. wg-077 ate RS /7/0 Sheet of

14 lign corner pieces to cabinets and each other (if there are upper and lower sections, it may be necessary to adjust up or down slightly to accomodate those trim pieces) Install small trim piece first using # drill screws supplied by Nevco Install large trim piece second using # drill screws supplied by Nevco orner Trim Installation Use # drill screws to attach large trim piece to small trim piece (holes are prepunched on large trim piece) Four Face Installation 8' enter Section Standard Scoreboards Last EO rawn ate RS /7/0 Greenville, Illinois rawing No. wg-077 Sheet of

15 connection Face oax Signal In See etail To Right connection Face ox and over Supplied by Nevco oax In From ontrol Point To Face Supplied by others onnection (Typical) connection Face Model mps (0V) Total -Face oard mps (0V) -NL -RL -ETN-NL -ETN-RL -NL -RL -ETN-NL -ETN-RL 700/70... N/.7.8. N/ 70/ / connection Face oax To Face Notes:. oax cables shown connecting from face to face to face to face supplied by Nevco.. cables for each face supplied by Nevco. This sign is intended to be installed in accordance with the requirements of rticle 00 of the National Electric ode and/or other applicable local codes. This includes proper grounding and bonding of the sign. oax to Face Last EO rawn -Face Wired Installation oax To Face Greenville, Illinois rawing No ate Sheet of LP 0//0

16 connection Face oax Signal In See etail To Right connection Face onnection (typical) Supplied by others Phone able In From Receiver To Face oax To Face connection Face Model mps (0V) Total -Face oard mps (0V) -NL -RL -ETN-NL -ETN-RL -NL -RL -ETN-NL -ETN-RL 700/70... N/.7.8. N/ 70/ / N/ N/. N/ N/ N/. N/ 78 N/ N/.8 N/ N/ N/.9 N/ N/ N/.9 N/ N/ N/.9 N/ connection Face oax To Face Notes:. oax cables shown connecting from face to face to face to face supplied by Nevco.. cables for each face supplied by Nevco. This sign is intended to be installed in accordance with the requirements of rticle 00 of the National Electric ode and/or other applicable local codes. This includes proper grounding and bonding of the sign. oax to Face -Face Wireless Installation Last EO rawn Greenville, Illinois rawing No ate Sheet of LP 0//0

17 -- LEFT OTTOM RIGHT OTTOM. NOTE TWO SIES OF THE -FE SOREOR RE NOT SHOWN FOR LRITY. INSTLL THE 7 OTTOM SETIONS MUH LIKE YOU WOUL SUSPENE EILING PNEL FROM UNERNETH THE -FE SOREOR.. FIRST PLE THE LEFT OTTOM SETION.. THEN PLE THE RIGHT OTTOM SETION. PLESE NOTE THIS HS LIP ON IT.. O NOT WLK ON THE 7 OTTOM SETIONS. THEY RE NOT ESIGNE TO SUPPORT ITIONL WEIGHT.. 7 OTTOM TOTL WEIGHT IS 0 LS. INSTLLTION 7 OTTOM W/ -FE Last EO rawn 0xxx ate HW 8//09 Greenville, Illinois rawing No. Sheet of -0