No.:EX## OMH0025. Technical specification. Output block / Power block EX9-OET1 EX9-OET2 EX9-OEP1 EX9-OEP2 EX9-PE1

Transcription

1 No.:EX## OMH Technical specification Output / Power EX9-OET EX9-OET EX9-OEP EX9-OEP EX9-PE

2 Table of Contents.Safety instructions.model -.Output for low wattage load -.Output for high wattage load -.Power -.Accessory cable -.Option.Specifications -.General specifications -.Electric specifications -.Applicable / solenoid valve series.wiring and Setting -.Output connector and circuit construction -.Power wiring -.Installation and maintenance P P P P P P P P P P P P P P8 P9.LED Display and Dimensions P - LED display P - Dimensions P 6.Troubleshooting 7.Attachment P P - - EX## OMH

3 .Safety instructions This manual contains essential information for the protection of users and others from possible injury and damage to property and to ensure correct handling. Please confirm that you fully understand the meaning of the following messages (signs) before reading the remaining text, and always follow the instructions. Also carefully read the instruction manual for any relevant equipment or apparatus before use. Indications IMPORTANT MESSAGES Read this manual and follow the instructions. Signal words such as WARNING, CAUTION and NOTE, will be followed by important safety information that must be carefully reviewed. Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions. Indicates a potentially hazardous situation which if not avoided, may result in minor injury or moderate injury. NOTE Provides helpful information. Operator This manual has been written for those who have knowledge of machinery and apparatuses that use pneumatic equipment and have full knowledge of assembly, operation and maintenance of such equipment. Please carefully read and understand this manual before assembling, operating or performing maintenance on the product presented in this manual (output and power ). Usage Restrictions This product is designed to be used in general equipment for factory automation. Never use this product with an equipment or apparatus that directly concerns human life* or in which a malfunction or failure can cause a great loss. *: Equipment or apparatus that directly concerns human life refers to means the following: Medical equipment such as life support systems or equipment used in operating rooms Compulsory equipment required by law such as the Fire Prevention Law, Construction Law, etc. Equipment or apparatus that conforms with those mentioned above. Contact our sales department when the product is planned to be used for a system* or equipment that concerns the safety of persons or that seriously affects the public. Such usuage requires special consideration*. *: A system or equipment that concerns the safety of persons or that seriously affects the public refers to the following: Nuclear reactor control system in a nuclear power plant, safety protection systems or other systems important for safety in a nuclear power facility. Driving control system for a mass transportation system, and flight control systems Equipment or apparatuses that comes in contact with foods or beverages *: Special consideration refers to discussing the usage with our engineers to establish a safe system which is designed as foolproof, fail-safe, redundant etc. Special consideration* should be taken regarding safety or maintainability to prevent a failure or malfunction which can cause a hazard or loss. This is likely to occur under certain environmental stresses (deterioration). *: Special consideration means fully review of the equipment or apparatus during the design stage and establishing of a backup system in advance, such as a redundant system or fail-safe system. - - EX## OMH

4 Do not disassemble, modify (including printed circuit board changes) or repair. An injury or failure can result. Do not operate the product outside of the specification range. Operation in a range that exceeds the specification can cause a fire, malfunction, or damage to the product. Verify the specifications before use. Do not use the product in an atmosphere containing combustible, explosive or corrosive gas. It can cause a fire, explosion or corrosion. This product is not designed to be explosion-proof. These instructions must be followed when using the product in an interlocking circuit: Provide double interlocking through another system such as mechanical protection Check the product regularly to ensure proper operation Otherwise a malfunction can cause an accident. These instructions must be followed when performing maintenance work: Turn off the power supply Stop the air supply, exhaust the residual pressure and verify that the air is released before performing maintenance work. Release all energy stored in the equipments or devices (hydraulic pressure, mechanical springs, electric capacitors or gravity force), verify that the energy is reset to zero, and then perform maintenance work. Otherwise it can cause an injury. Perform proper functional checks after maintenance work. Stop operation when an abnormality is observed such as the product not working properly. Safety can not be assured due to unexpected malfunctions. NOTE Follow the instructions given below when selecting and handling your the product: The instructions on selection (installation, wiring, operating environment, adjustment, operation and maintenance) described below must also be followed. Product specifications Operate the product with the specified voltage. Operating with a voltage outside of the specification can cause a malfunction or damage to the unit. Reserve free space for maintenance Remember to leave free space for maintenance when designing a layout for the unit. Do not remove the labels. Otherwise in error during maintenance work or misreading of an operation manual can cause damage or malfunction. It may also result in the nonconformance to safety standards. - - EX## OMH

5 Selection ()Output for high wattage load The output for high wattage load can't be used independently. Be sure to combine with the power for use. For high wattage load EX9-OEP Power For high wattage load EX9-OEP EX9-PE ()Position of output for high wattage load The output for high wattage load can't be mounted at the place nearer than the power. However, that place is acceptable if the power is located between and the output for high wattage load. For high Power For high Power For high Power For high wattage load wattage EX9-OEP EX9-PE load Block wattage Block wattage load load EX9-OEP EX9-PE EX9-OEP EX9-PE EX9-OEP ()Output for low wattage load The output for low wattage load can't be mounted at the right side of the power. Mount on to the place near rather than the power. For low wattage load EX9-OET Power EX9-PE For low wattage load EX9-OET For low wattage load EX9-OET - - EX## OMH

6 ()Load connected to output for low wattage load EX6/EX series (except for one power supply system of AS-i) The load exceeding 6mA [.W, DCV] can't be connected. For low wattage load EX9-OET For low wattage load EX9-OET Power EX9-PE For high wattage load EX9-OEP Relay 6mA Fan.A Relay 6mA External power supply Fan.A Solenoid valve 6mA Lamp.A Solenoid valve 6mA Lamp.A EXseries The load exceeding ma [.W, DCV] can't be connected. For low wattage load EX-Q EX9-OET EX-Q Power EX9-PE For high wattage load EX9-OEP COM COM EX Series EX Series Relay 6mA Solenoid valve ma Power Relay 6mA Solenoid valve ma Buzzer 6mA Lamp ma Solenoid valve 6mA Solenoid valve ma ()The number of output point when the power is used When the power is used, the number of output point including the solenoid valve positioned after the power is as follows. Table. Max. output point when the power is used Spec. of the 6 Output points Pert No. of the EX6D-SMJ(Note ) Max. output point when the power is used 6 points Input/Output points EX-SDN,SMJ,SPR,SCA(Note ) points Input/Output points EX-SAS,SAS9 points 8 Input/Output points EX-SAS,SAS7 8 points Gateway type 6 Output points EX-Q,Q 6 points (Note ) If the output is added to the EX series, it can be connected to the product with manufacturing lot GV (Aug. ) or later. In case of EX6 series, the output can be connected to the plate assembly shipped in March or later. These products and assembly have the body to enable connection with the output. - - EX## OMH

7 (6)Supply (page for detail) Supply for The max. supply for each is as shown on the following table. The consumption of the output for low wattage and high wattage is limited depending on the value of max. supply. The max. supply of must not be exceeded. Table Max. supply for Spec. of 6 outputs Part no. of EX6D-SMJ Output max supply.a inputs/outputs EX-SDN,SMJ,SPR,SCA A power supply systems, 8 inputs/outputs EX-SAS.A power supply system, inputs/outputs EX-SAS.A power supply systems, 8 inputs/outputs EX-SAS7.A(Note )(Total of inputs/outputs) power supply system, inputs/outputs EX-SAS9.A(Note )(Total of inputs/outputs) Gateway type, 6 outputs EX-Q,Q.7A (Note ) For one power supply system of AS-i, the max. supply in total of inputs/outputs is applicable. EX-Q For low wattage load EX9-OET EX-Q Power EX9-PE For high wattage load EX9-OEP COM COM EX Series EX Series Max. supply.7a Internal consumption + Connected load Total.7A Max. supply.7a Only internal consumption Total.7A Connected load Refer to the following Supply for power The max. supply for the power is.a*. The max. supply must not be exceeded. Power For high wattage load EX9-PE EX9-OEP Supply between and power Power EX9-PE For high wattage load EX9-OEP Solenoid valve manifold Internal consumption + Connected load of power Total.A* Total.A* Power supply system for solenoid valve Internal consumption Connected load of for high wattage load + Solenoid valve manifold Power supply system for power Consumption Connected of power + load * : If max. supply (. to.a) is applied for operation, do not make the ambient temperature exceed and bundle the cable. Total.A Total.A EX## OMH

8 (7)One power supply system of AS-i 8 inputs/outputs [EX-SAS7] (Max. ma) The max. supply (ma) must not be exceeded. For detail, refer to page. EX-IE EX-SAS7 For low wattage load EX9-OET inputs/outputs [EX-SAS9](MAX ma) The max. supply (ma) must not be exceeded. For detail, refer to page. EX-IE EX-SAS9 Output EX9-OET CLEAR SW AUX IN COM -ERR -ERR HOLD ADDRESS SETTING CLEAR SW AUX IN COM -ERR -ERR HOLD ADDRESS SETTING ADDR ADDR ADDR ADDR EX EX Max. supply ma Input consumption Internal consumption +Connected load Max. supply ma Input consumption Internal consumption +Connected load Total ma Total ma Total ma Total ma (8)Polarity of output If the polarity (output common) of the is different from the output polarity of connected output, the normal operation can't be obtained. Be sure to make the output polarity of connected output consistent with the polarity (output common) of the. PNP output (-COM) NPN output (+COM) EX9-OET PNP output (-COM) NPN output (-COM) EX9-OET (9)The number of connected station The max. connected station in total of input/output (excluding ) is. EX-IE Output EX9-OET Output EX9-OET CLEAR SW AUX IN COM -ERR -ERR HOLD ADDRESS SETTING ADDR ADDR EX Input station + Output station Total station ( or more) Total station EX## OMH

9 ()Connection of inductive load If the connected load is an inductive type such as a solenoid valve and relay, be sure to select a built-in type surge voltage protective circuit (surge suppressor) or externally connect a protective circuit. Without it, a malfunction and or damage may occur. For low wattage load EX9-OET For low wattage load EX9-OET Solenoid valve without surge suppressor 6mA Relay without surge suppressor 6mA Solenoid valve with surge suppressor 6mA Relay with surge suppressor 6mA Solenoid valve without surge suppressor 6mA Relay without surge suppressor 6mA Solenoid valve with surge suppressor 6mA Relay with surge suppressor 6mA Instructions on handling Installation Do not drop, hit or apply excessive shock to the product. Otherwise, it the product can be damaged and have failure or malfunction. Follow the specified tightening torque. Excessive tightening torque can break the screws. Refer to -6 Installation and Maintenance for installation. Wiring (including plugging in/out of connector) Do not bend or apply tensile force to the cables, or apply force by placing a heavy load on them. Wiring that has bending or tensile stress can cause the cables to break. Connect wires and cables correctly. Miswiring can damage the product depending upon condition of the wiring. Do not connect wires while the power is on. Otherwise, it can damage the product or I/O devices and cause damage or malfunction. Do not lay wires or cables in the same wiring route as power cables or high voltage cables. Otherwise the wires to the product can be interfered with noise or induced surge voltage from power lines or high voltage lines, resulting in a malfunction. Lay the wires to the product and each I/O device in a wire duct or in a protective tube other than those for power lines or high voltage lines. Verify the wiring insulation. Poor insulation (interference with other circuits, poor insulation between terminals, etc.) can introduce excess voltage or to the product or each I/O device causing damage. Separate the power lines for the solenoid valves from the power lines for the Input and control unit. Otherwise, the wires can be contaminated with noise or induced surge voltage, resulting in a malfunction. Take proper measurements against noise such as using a noise filter, when the product is incorporated in an equipment or device. Otherwise, interference from noise can cause a malfunction EX## OMH

10 Environment Take sufficient measures with shielding, when installing in the following places. Insufficient measures can cause a malfunction or failure. Verify the effect of the shielding measures after installation of the unit in equipment or devices: ()A place where noise is generated due to static electricity. ()A place where electric field strength is high ()A place where there is irradiation ()A place near a power line Do not use the product near a place where electric surges are generated. Internal circuit elements of the product can deteriorate or become damaged when equipment generating a large surge (electromagnetic lifter, high frequency induction furnace, motor, etc.) is located near the product. Provide surge suppression, and avoid interference. Use the product equipped with a surge absorber when a surge the generating load, such as a relay or solenoid valve, is directly driven. Direct drive of a load generating surge voltage can damage the product. Prevent foreign matter such as remnant wires from entering this product. Take proper measures to prevent the foreign matter from entering the product in order to prevent a failure or malfunction. Do not expose the product to vibration and impact. Otherwise, it can cause a failure or malfunction. Maintain the specified ambient temperature range. Otherwise, it can cause a malfunction. Do not use the product in a place where the temperature abruptly changes even if it stays within the specified range. Do not expose the product to heat radiation from a heat source located nearby. This can cause a malfunction. Maintenance Before performing maintenance work, make sure to turn of the power supply, stop air supply, release the residual air in the piping into the atmosphere, and verify that the pneumatic system is open to the air. Otherwise, an unexpected operation from a system component may occur. Perform maintenance and check regularly Otherwise, an unexpected malfunction of the system can occur due to a malfunction of the unit. Refer to -.Installation and Maintenance the maintenance and checking methods. Perform a proper functional check. Stop operation when an abnormality is observed in witch the device does not work properly. Otherwise, an unexpected malfunction of the system component can occur. Do not use solvents such as benzene, thinner, etc., to clean the product. It can damage the surface of the body and erase the indication on the body. Use a soft cloth to remove stains. For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe the stains again with a dry cloth EX## OMH

11 .Model -.Output for low wattage load Electrical specifications Power supply Max. load Internal consumption Output point voltage[v] [ma] point [W] point [ma]/point [point/] DCV 6mA*.W* ma points EX9-OET PNP output type (-COM) EX9-OET NPN output type (+COM) MAX 6mA Output EX9-OET * :ma and W for connection to EX series MAX 6mA Output EX9-OET Load Load Output connector No. Load Load Output connector No. Output connector No. Output connector No. * PIN No. Output connector No. Output connector No. NC NC OUT* NC GND GND OUT OUT* NC NC PIN No. Output connector No. Output connector No. VDC VDC OUT* NC NC NC OUT OUT* NC NC NC: non-connection NC: non-connection :The pin No. of the output connector No. are connected to pin No. of the output connector No. inside respectively. -.Output for high wattage load* Electrical specifications Power supply Max. load Internal consumption Output point voltage[v] [A] point [W] point [ma]/point [point/] DCV.A W ma points MAX.mA Output EX9-OET * :Combined with power EX9-PE for use. EX9-OEP PNP output type (-COM) EX9-OEP NPN output type (+COM) MAX.A Output EX9-OEP Load Load Output connector No. Load Load Output connector No. Output connector No. Output connector No. * PIN No. Output connector No. Output connector No. NC NC OUT* NC GND GND OUT OUT* NC NC PIN No. Output connector No. Output connector No. VDC VDC OUT* NC NC NC OUT OUT* NC NC NC: non-connection NC: non-connection :The pin No. of the output connector No. are connected to pin No. of the output connector No. inside respectively. - - EX## OMH

12 -.Power Electrical specification Power supply Max. load Internal consumption voltage [V] [A] [ma]/unit DCV.A* ma * : If max. supply (. to.a) is applied for operation, do not make the ambient temperature exceed and bundle the cable. EX9-PE A. Wiring to connect the power with the power supply Power EX9-PE VDC MAX.A* Power supply connector No. Power supply connector No. PIN No. Power supply connector No. Power supply connector No. - DCV - DCV E DCV,V:Output side power supply E:Earth -:Unused B.The supply of power from the power connector to the The power supply connector No. is available for power supply to because the power supply connector No. is connected to each PIN. Only in case that is located next to the power, dedicated accessory cable which is originally prepared for bypass connection can be used. EX series Power EX9-PE BUS Power supply connector No. Power supply connector No. Accessory cable VDC MAX.A* PIN No. Power supply connector No. Power supply connector No. SV V_SI DCV SV V_SI DCV SW V_SI DCV SW V_SI DCV E_SI E SVV,V_SI:Output (solenoid valve) side power supply SWV,V_SI:Input/control side power supply E, E_SI:Earth - - EX OMH

13

14 -.Option EX series for mounting of output This is EX series specific for mounting of output. * Only VQC series solenoid valve is applicable. EX - Q series for grounding VQC for mounting of output COM. symbol COM. +COM. -COM. COM EX Series End plate This is the end plate without solenoid valve used. EX9 - EA series End plate Type Symbol Type Output side end plate Output side end plate (with DIN rail mounting bracket) - - EX## OMH

15 .Specifications -.General specifications Item Specification Ambient temp. to + C (Solenoid valve type) Ambient humidity to 8% RH (No dew condensation) Storage temp. to +6 C Vibration proof to Hz.mm (constant vibration) to Hz m/s (constant acceleration) Impact proof m/s (peak), ms times in each direction ±X,Y,Z Withstand voltage AC V for min (between external terminals and the case) Insulation resistance DCV with Mohm or more (between external terminals and the case) Operating environment No corrosive gas Enclosure IP67 Weight g or less -.Electrical specifications --.Output Item Specification EX9-OET/ EX9-OEP/ Output points points Rated voltage DCV Rated load Max. 6mA/point* Max..A/point* Power supply Internal power source Package supply from external* EX9-OET, EX9-OEP:N-ch MOS-FET High side switch (PNP output) Output EX9-OET, EX9-OEP:N-ch MOS-FET Low side switch (NPN output) Insulation Opto-coupler insulation Opto-coupler insulation *:Max. ma(.w)/point when connected to EX series. *:Max. supply is.a* per power. *:Combined with the power for use. --.Power specifications (EX9-PE) Item Specification Rated voltage V DC Supply Max..A * Applicable output EX9-OEP, EX9-OEP *:If max. supply (. to.a) is applied for operation, do not make the ambient temperature exceed C and bundle the cable. -.Applicable / solenoid valve series --.Applicable * Output Applicable EX-SDN, EX-SPR, EX-SAS, EX-SAS, EX-SAS7* 6, EX9-OET, EX9-OEP EX-SAS9* 6, EX-SCA, EX-Q EX9-OET, EX9-OEP EX6D-SMJ, EX-SMJ, EX-Q *:If the output is added to the EX series, it can be connected to the product with manufacturing lot GV (Aug. ) or later. In case of EX6 series, the output can be connected to the plate assembly shipped in March or later. These products and assembly have the body to enable connection with the output. *6:In one power supply system of AS-i, since supply is limited, it is necessary to calculate the supply. Refer to the section showing calculation of supply in one power supply system of AS-i. --.Applicable solenoid valve series Applicable solenoid VQC,, series valve series SV,, series (EX series except) - - EX## OMH

16 .Wiring and Setting -.Output connector and circuit construction EX9-OET/EX9-OET Output connector PIN No. EX9-OET Output connector No. Output connector No. NC NC OUT NC GND GND OUT OUT NC NC M poles (Female) Example of connector: Omron Corp. XSH,XSG etc. Franz Binder Series 7,76 Example of connected cable: SMC's part no. EX9-AC###-7 Output connector No. DCV OUT EX9-OET NC: Non-connection Output connector No. provides outputs. If the enclosure equivalent to IP67 is required, be sure to mount waterproof cap on unused connector. The waterproof cap needs to be prepared separately. (SMC's part no. EX-AWTS etc) NC OUT NC Output connector No. DCV NC NC OUT NC Circuit construction EX9-OET EX9-OET +COM Internal circuit Internal circuit GND +COM Connector for solenoid valve Connector for solenoid valve Output Connector for Output Connector for LED LED LED LED Over protection Heat protection Over protection Heat protection OUT OUT -COM OUT OUT +COM Connector for solenoid valve Connector for solenoid valve GND - - EX## OMH

17 EX9-OEP/EX9-OEP Output connector PIN No. EX9-OEP Output connector No. Output connector No. NC NC OUT NC DCV DCV OUT OUT NC NC M poles (Female) Example of connector: Omron Corp. XSH,XSG etc. Franz Binder Series 7,76 Example of connected cable: SMC's part no. EX9-AC###-7 Output connector No. DCV OUT EX9-OEP NC: Non-connection Output connector No. provides outputs. If the enclosure equivalent to IP67 is required, be sure to mount waterproof cap on unused connector. The waterproof cap needs to be prepared separately. (SMC's part no. EX-AWTS etc) NC OUT NC Output connector No. DCV NC NC OUT NC Circuit construction EX9-OEP EX9-OEP Power Output Internal circuit Internal circuit GND +COM Connector for solenoid valve Connector for power Power Output GND +COM Connector for solenoid valve E E Connector for power LED LED LED LED Over protection Heat protection -COM DCV DCV Over protection Heat protection +COM OUT OUT OUT OUT Connector for solenoid valve Connector for solenoid valve DCV DCV EX## OMH

18 EX9-PE Power supply input connector No. M poles reverse (Male) Example of connector cable: SMC EX9-AC###- etc. Power supply connector No. M poles reverse (Female) Example of connector cable: SMC EX9-AC###-,,,6 etc. PIN No. Power supply connector No. SV V SV V (SV V)* (SV V)* E PIN No. Power supply connector No. (SV V_SI)* (SV V_SI)* (SW V_SI)* (SW V_SI)* (E_SI)* * :The power supply connector is prepared for supplementation and not used basically. If the power is connectedright next to EX series in manifold, the connector is used as jumper to power supply for. If the enclosure equivalent to IP67 is required, be sure to mount waterproof cap on unused connector. The water proof cap is attached as accessory to power supply connector side. * :If max. supply (. to.a) is applied for operation, do not make the ambient temperature exceed and bundle the cable. Note:The max. allowable of power is.a*. The max. allowable per pin of M connector mounted on power supply is.a*. For detail, refer to the section for supply calculation(page ). Circuit construction EX9-PE Power E Connector for solenoid valve COM Connector for output VDC VDC EX## OMH

19 -. Power wiring A. The power supply for is separate from power. EX-IE EX-SDN EX9-PE EX9-OEP EX9-OEP BUS Power supply for input and control Power supply for output (solenoid valve) Power supply for output B.The supply of power from power connector to. The power supply connector No. is available for power supply to because power supply connector No. is connected to each PIN. Only in case that is located next to the power, dedicated accessory cable which is originally prepared for bypass connection can be used. EX series Power EX9-PE BUS Power supply connector No. Power supply connector No. Accessory cable VDC MAX.A* *:If max. supply (. to.a) is applied for operation, do not make the ambient temperature exceed and bundle the cable EX## OMH

20 TM -.Installation and maintenance How to set Output and power can't installed and controlled independently. Be sure to connect to them. Setting example The number of solenoids =n(pieces) The number of input s The number of output s OUTPUT OUTPUT (V) MOD/NET SETTINGS EX 66 (mm) EX L n_m L L * *The number of input s+the number of output s+the number of power s=m(pieces) (mm) Each dimension is for the condition with VQC series solenoid valve and EX series connected. With regards to the dimension L, the standard setting is what makes the relation, m < =. For setting of pieces over, consult with SMC sales. For the dimension with other series of solenoid valve and connected, refer to specifications of individual product. Wiring (for power supply, communication and input) and piping are done on only one side, make a space for wiring and piping. Maintenance Be sure to turn off the power supply before the maintenance. Addition of output. Remove screws from end plate.. Release connection among input (if connected), and valve manifold (if connected).. Mount attached tie rod.. Connect additional output.. Mount removed input (if connected), and valve manifold (if connected).. Connect end plate and tighten removed screws at specified torque.(.6 N. m) Replacement of output. Remove screws from end plate and release connection among input (if connected), and valve manifold (if connected).. Replace old output with new one. (Tie rod does not need to be removed.). Mount removed input (if connected), and valve manifold (if connected).. Put back end plate and screws and tighten the screws at specified torque.(.6 N. m) EX## OMH

21 For maintenance () Be sure to turn off all power supplies. () Be sure that there is no foreign matter in any of products. () Be sure that there is no foreign matter attached on the gasket. () Be sure that tightening torque is according to specification. If these items are not kept, it may lead to the breakage of board or intrusion of liquid or dust into the products. Assembly and disconnection of the product M hexagon screw Tightening torque.6n m Tie rod Gasket Tie rod End plate Output Valve manifold.led display and Dimensions -.LED display EX9-OET, EX9-OET EX9-OEP, EX9-OEP OUTPUT EX9-PE Name Contents Name Contents, Each LED lights up when OUT and OUT output. Lights up when external power is supplied. - - EX## OMH

22 -.Dimensions EX9-OET, EX9-OET EX9-OEP, EX9-OEP Pin header Connector for (EX9-OET/) Connector for power (EX9-OEP/) Receptacle Connector for solenoid valve OUTPUT Output connector No. 6.7 Output connector No. EX9-PE Pin header Connector for Receptacle Connector for output Power supply connector No. 6.7 Power supply input connector No. - - EX##-OMH

23 6.Troubleshooting Output to LED Yellow doesn't light up. Yellow doesn't goes off. Output signal ON/OFF LED [Countermeasure]. Check mounting condition of connector.. Check type of output (PNP/NPN).. Replace operating load and try again.. Replace output.. Replace. Power LED Green doesn't light up. Power supply ON/OFF LED [Countermeasure]. Check external power supply (DCV).. Replace power. - - EX##-OMH

24 7.Attachment Power supply system diagram The power to the output for low wattage load is supplied from like the solenoid valve manifold. The power to the output for high wattage load is supplied from the power. Addition of the power enables separation of the power supply for high wattage solenoid valve from the one for fan. Power supply for solenoid valve (COM) (from ) Power supply for high wattage load (from power ) VDC Power supply for solenoid valve VDC,.A* Power supply for power VDC,.A* Power supply for power Low wattage solenoid valve 6mA Relay 6mA High wattage solenoid valve (Max.W/point) Lamp (Max.W/point) Fan (Max.W/point) Fig. Power supply system diagram for output * :If max. supply (. to.a) is applied for operation, do not make the ambient temperature exceed and bundle the cable. :Power supply system for low wattage load and solenoid valve :Power supply system for high wattage load :Power supply system for high wattage load - - EX## OMH

25 Supply Current Calculation The power supply system of depends on max. of each. (Refer to the following table.) The max. allowable for the power is.a*. :Power supply system for solenoid valve and low wattage load : EX-SDN(MAX.A). Internal consumption Output points of output (sum of the for low wattage and high wattage loads) x Consumption (@ma) Example points x ma=ma. Load consumption Consumption of manifold valve + Capacity of load connected to output for low wattage load Example (ma x 7st.) + (6mA x ) = 8mA Total: Internal consumption + Load consumption Example ma + 8mA =.7A A OK :Power supply system for power Power (MAX..A* ). Internal consumption Power consumption = ma. Load consumption Capacity of load connected to output for high wattage load (.A x 6) = A Total: Internal consumption + Load consumption Example ma + A =.A.A* OK Criterion :Power supply system for power Power (MAX..A* ). Internal consumption Power consumption = ma. Load consumption Capacity of load connected to output for high wattage load (.A x ) = A Total: Internal consumption + Load consumption Example ma + A =.A.A* OK Criterion * :If max. supply (. to.a) is applied for operation, do not make the ambient temperature exceed and bundle the cable. Power supply system Total.A Power supply system Total.A Power supply system Total.8A Internal consumprion Load consumprion Internal consumprion Load consumprion Internal consumprion Load consumprion ma ma ma A A A ma ma ma ma A A ma ma VQC 7 station max7=9ma Criterion Power supply for solenoid valve (COM) (from ) Power supply for high wattage load (from power ) VDC Power supply for solenoid valve VDC,.A* Power supply for power Low wattage solenoid valve 6mA Relay 6mA High wattage solenoid valve.ax6 VDC,.A* Power supply for power Lamp.Ax Fan.Ax Fig.Current applied to each power supply system Spec. of Part No. of Max. Current 6 outputs EX6D-SMJ.A EX-SDN inputs/outputs EX-SMJ EX-SPR A EX-SCA 8 inputs/outputs, power supply systems EX-SAS.A inputs/outputs, power supply systems EX-SAS.A 8 inputs/outputs,.a power supply systems EX-SAS (Note ) inputs/outputs,.a power supply systems EX-SAS (Note ) Gatewey, 6 outputs EX-SAS.7A Note) For one power supply system of AS-i, the max. supply in total of inputs/outputs is applicable. - - EX OMH

26 Supply Current Calculation for One Power Supply System of AS-i In one power supply system of AS-i, since the supplied for input and output equipment is limited, it is necessary to calculate the consumed by these equipment. EX-SAS7. Max. supply : ma. Internal consumption... Output points of output (sum of the for low wattage and high wattage loads) x Consumption (@ma) Example 6 points x ma=ma. Load consumption... Sensor consumption +Capacity of load connected to output for low wattage load+solenoid valve consumption Example ma+(ma+ma+ma)+.8ma=.8ma Total: Internal consumption + Load consumption Example ma+.8ma=.8ma ma OK Total consumption.8ma Max. supply Internal consumprion Load consumprion ma ma ma ma ma ma Criterion ma ma.8ma EX Input EX-IE EX-SAS7 Load ma Load ma Load ma Solenoid valve Total consumption.8ma Internal consumprion Load consumprion Output (For low wattage load) Fig. Consumption in EX-SAS7 EX-SAS9. Max. supply : ma. Internal consumption... Output point of output (sum of the for low and high wattage load) x Consumption (@ma) Example points x ma = ma. Load consumption... Sensor consumption + Capacity of load connected to low wattage load + Solenoid valve consumption Example ma+ma+.8ma=7.8ma Total: Internal consumption + Load consumption Example ma + 7.8mA =.8mA ma OK Max. supply Criterion ma.8ma ma ma ma EX Input EX-IE EX-SAS9 Load ma Solenoid valve Output (For low wattage load) Fig. Consumption in EX-SAS9 - - EX## OMH

27 Connector Wiring Diagram between Output Blocks The output for low wattage load is applicable to output signals at max. through internal connectors (No. to ). However, the power and output for high wattage load use the output signals (No.7 to ) at low side to supply the power from the power to the output for high wattage load and so are applicable to output signals at max. ( minus 8 = ). 6 7 Output COM For low wattage load For low wattage load Power For high wattage load For high wattage load EX9-OET EX9-OET EX9-OET EX9-OET EX9-PE EX9-OEP EX9-OEP EX9-OEP EX9-OEP Fig. Connector wiring between output s The example of calculating the number of output point point point point point 8point 8point 6point point The rest number of output point point point point point point The number of output Output (For low wattage load) Power Output (For high wattage load) Power Output (For high wattage load) EX-SDN EX9-OET EX9-PE EX9-OEP EX9-PE EX9-OEP Fig. Example of calculating the number of output EX## OMH