Configuration Instructions: Dual Cabled RS232 Diva scale: Either EPOS or EPOS2 Protocol
|
|
- Clarence Rogers
- 6 years ago
- Views:
Transcription
1 I INSTALLATION CABLE INSTALLATION (INTERFACE SPECIFIC) RS232 The following steps describe how to properly install the cables for an RS232 StratosH application. The scanner/diva scale must then be configured to match the host s RS232 parameters. Cable installation alone does not guarantee that the StratosH will communicate properly with the host system. 1. Turn off the host system. 2. Plug the 10-pin RJ45 end of the RS232 interface cable (MLPN x-N-3) into the 10-pin socket labeled Scanner RS232 to Host, on the bottom of the StratosH. 3. Connect the other end of the RS232 cable to the proper communication port on the host device. 4. Plug the dual interface cable (MLPN x-N-3) into the 10-pin socket labeled, Scale RS232 to Host, on the bottom of the StratosH. 5. Connect the other end of the dual interface cable (MLPN x-N-3) to the appropriate communication port on the host s scale device. 6. Plug the optional remote display cable** into the 10-pin socket labeled, Scale to Display, on the bottom of the StratosH. 7. Plug the dual interface cable (MLPN x-N-3) into the 10-pin socket labeled, Scale RS232 to Host, on the bottom of the StratosH. 8. Connect the other end of the dual interface cable (MLPN x-N-3) to the appropriate communication port on the host s scale device. Plug the optional remote display cable** into the 10-pin socket labeled, Scale to Display, on the bottom of the StratosH. 9. Connect AC power to the transformer. If the AC outlet is equipped with an on/off switch, turn the power on. 10. Turn on the host system. Version 1.1 Page 1 of 8
2 Figure 1. RS232 Interface Cable Installation Schematic Scanner & Scale Configuration Scan the following bar codes, one at a time, using the vertical window of the scanner. Wait for the confirmation beep tones after each bar code scan. Recall RS232 Defaults RS232 Recall Defaults ³ Version 1.1 Page 2 of 8
3 Scan Dual Cable Interface Dual Cable Mode ³ ***NOTE: Select either EPOS or EPOS2 Protocol *** EPOS sets the scale to RS232 protocol to Serial EPOS EPOS Protocol ³ Communication Port Settings: 2400 Baud Rate; 7 Data Bits, 1 Stop bit, Even Parity OR EPOS2 sets the scale to RS232 protocol to Modified Serial EPOS. This protocol does not require the POS terminal to send the weight back to the scale for validation. EPOS2 Protocol ³ Communication Port Settings: 2400 Baud Rate; 7 Data Bits; 1 Stop Bit; Even Parity Save the Data Save Data ³ ***The scanner & scale are now configured for Dual Cable Serial Data. *** Version 1.1 Page 3 of 8
4 Testing Open MetroSet 2 MetroSet 2 can be downloaded at Metrologic Instruments web site: Select MetroSet2 configuration & Utility Software from the drop down menu. After installation has been completed Open MetroSet 2 and choose Stratos 20xx/21xx/23xx from the list and click on the Configure Stratos 20xx/21xx/23xx button to proceed to the configuration screen. Open the terminal window. Dual cable communication 1. Test the scanner Open MetroSet Terminal Window with Scanner COM port, scan a bar code, and see that the data appears in the Terminal Window. The data should appear in the following format: [STX]08<code ID><bar code data>[etx]<bcc> <code ID> is the code identifier. Example: "A" indicates UPC-A <bar code data> is the information in the bar code <BCC> is for error checking. It can be any ASCII character. 2. Test the scale Open MetroSet Terminal Window with Scale COM port; send the following command string to request the weight: W[CR] [CR] is Carriage Return (or Enter) The scale should respond in the following format: [LF]<weight>LB[CR][LF]S2pp3[CR][ETX] <weight> is the decimal weight in pounds (or kilograms, if metric) Version 1.1 Page 4 of 8
5 Creating MetrOPOS Profile: The scanner/scale programming is complete. Next, install the OPOS driver, and create scanner and scale profiles. In order to set up the OPOS device profiles for the scanner and scale, you must have downloaded and installed the MetrOPOS drivers and utility. This is available on the Metrologic corporate website at the following location: Under the Software dropdown menu select MetrOPOS Driver. Download and install the driver. It should install the MetrOPOS2 Administrator in your program group. Setup the profiles using the MetrOPOS2 Administrator for both the scanner and the scale. To do so, Start the MetrOPOS Administrator. The setup wizard may appear, if it does, just close the window. Next, select New Profile and setup the options for the scanner as shown below and Save: (Note: You can name the profile whatever you want, and be sure to select RS232 and dual Cable) Version 1.1 Page 5 of 8
6 Configure the Scale and select Create Profile After the profile has been created successfully press OK, select No. The OPOS drive should now be configured for the Scanner and Scale. Version 1.1 Page 6 of 8
7 Scanner Test: To test the Scanner select Detailed Test icon. In Detailed Test choose Scanner and your profile name. Click on Open, Claim, Enable and check Decode Data, Data Event Enabled, Always Enable Data Event. SCAN A PRODUCT BARCODES if you are able to see the data, the scanner is sending data Version 1.1 Page 7 of 8
8 Scale Test: To test the Scale select Detailed Test icon. In Detailed Test choose Scale & your profile Name. Click on Open, Claim, Read Weight. Reading Weight with nothing on the scale should read Weight Data: 0.00 lb. Place weight on the SCALE if you are able to see weight data, the scale is sending data Document Revision Table: Revision Level Date Revised By Changes Made /22/2007 J. Willis Initial Document 1.1f 06/23/2008 J. Willis Updated combined EPOS & EPOS2 Version 1.1 Page 8 of 8
Setting up the Honeywell/Metrologic 2320 Scanner/Scale
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Setting up the Honeywell/Metrologic 2320 Scanner/Scale This
More informationSetting up the Honeywell/Metrologic 24xx Series Scanner/Scale
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Setting up the Honeywell/Metrologic 24xx Series Scanner/Scale
More informationIntroduction CAUTION. Setting Up the Scanner CAUTION
MDE-4354 Setting Up Metrologic MS6720 Bar Code Scanner August 2005 Introduction CAUTION Be aware of the following: When an IEE customer display is used, the scanner will be operating at the 9600 baud rate.
More informationMETROLOGIC INSTRUMENTS, INC. MS2320 StratosH Scanner / Avery Scale Installation and User s Guide
METROLOGIC INSTRUMENTS, INC. MS2320 StratosH Scanner / Avery Scale Installation and User s Guide Copyright 2006 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced,
More informationMETROLOGIC INSTRUMENTS, INC. MS2220 StratosS Scanner / Diva Scale Installation and User s Guide
METROLOGIC INSTRUMENTS, INC. MS2220 StratosS Scanner / Diva Scale Installation and User s Guide Copyright 2006 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced,
More informationMETROLOGIC INSTRUMENTS, INC. MS2220 StratosS Scanner / Avery Scale Installation and User s Guide
METROLOGIC INSTRUMENTS, INC. MS2220 StratosS Scanner / Avery Scale Installation and User s Guide Copyright 2006 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced,
More informationMETROLOGIC INSTRUMENTS, INC. MS2020 Stratos. Series Installation and User s Guide
METROLOGIC INSTRUMENTS, INC. MS2020 Stratos Series Installation and User s Guide LOCATIONS CORPORATE HEADQUARTERS NORTH AMERICA EUROPEAN, MIDDLE EAST & AFRICAN HEADQUARTERS USA, NEW JERSEY GERMANY, MUNICH
More informationMS2420 / MS2430. Bar Code Scanner / Diva Scale. Installation and User s Guide
MS2420 / MS2430 Bar Code Scanner / Diva Scale Installation and User s Guide Disclaimer Honeywell International Inc. ( HII ) reserves the right to make changes in specifications and other information contained
More informationMETROLOGIC INSTRUMENTS, INC. MS2421 / MS2422 Bar Code Scanner Installation and User s Guide
METROLOGIC INSTRUMENTS, INC. MS2421 / MS2422 Bar Code Scanner Installation and User s Guide Copyright 2007 by Metrologic Instruments, Inc. All rights reserved. No part of this work may be reproduced, transmitted,
More informationUnique Micro Design First Choice of Professional Systems Intergrators. Model 361 Terminal Keyboard Wedge User Manual
Model 361 User Manual Unique Micro Design First Choice of Professional Systems Intergrators Model 361 Terminal Keyboard Wedge User Manual Document Reference : DOC-M361-UM UMD Part Number : 6-0361-993-5
More informationToriemon FGV-X and FGV-HX INSTRUCTION MANUAL
FORCE GAUGE FGV-X SERIES Add-in software for EXCEL Toriemon FGV-X and FGV-HX INSTRUCTION MANUAL NIDEC-SHIMPO CORPORATION CONTENTS 1. Introduction 2. Setup 2.1 Software Package 2.2 Software Installation
More informationLeuze electronic. Dimensioned drawing. Electrical connection. Accessories
2D-code hand-held scanner Dimensioned drawing 4-14 V DC We reserve the right to make changes BP_IT4600_4800_GB.fm Part No. 501 06667! Hand-held scanner for Data-Matrix Codes and Bar Codes! Large reading
More informationBar Code Scanner Specifications for XL200 Controllers
Bar Code Scanner Specifications for XL200 Controllers Scanner Specifications Any scanner connected to an XL200 series controller must conform to the following communication specifications: Baud Rate: 9600
More informationHP Point of Sale (POS) Peripherals Configuration Guide Barcode Scanner
HP Point of Sale (POS) Peripherals Configuration Guide Barcode Scanner Document Version 2.10 July 2009 1 Copyright 2007-2009 Hewlett-Packard Development Company, L.P. The information contained herein is
More informationDoug Fleenor Design, Inc. RS-232 to DMX512 Interface, 2 Generation. March 8, 2010 (Software V1.2)
Doug Fleenor Design, Inc. nd RS-232 to DMX512 Interface, 2 Generation March 8, 2010 (Software V1.2) The second generation RS-232 to DMX512 interface has numerous features beyond the original device. The
More informationOperating Manual. Sigma Counting Scale. CTG-9850 Series (AC Powered) Issue #9 3/ by Fairbanks Scales Inc. All rights reserved
Operating Manual Sigma Counting Scale CTG-9850 Series (AC Powered) 2004 by Fairbanks Scales Inc. All rights reserved 50165 Issue #9 3/04 Amendment Record Sigma Counting Scale CTG-9850 Series 50165 Manufactured
More informationBW/BWS Weighing Indicator
BW/BWS Weighing Indicator - 1 - CONTENTS 1. SPECIFICATION... 2 2. INTRODUCTION... 3 3. INSTALLATION. 4 Precautions 4 Parts 4 Installation.. 5 4. KEYS DESCRIPTION... 6 Key Board... 6 Secondary functions
More information2D Image Handheld Scanner
1 Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0 9/6/2018 Initial release i Important Notice No warranty of any kind is made in regard to this
More informationQuantumT Omnidirectional Laser Scanner. User s Guide
QuantumT 3580 Omnidirectional Laser Scanner User s Guide Disclaimer Honeywell International Inc. ( HII ) reserves the right to make changes in specifications and other information contained in this document
More informationDWP-98 Series. Counting scale. User s Guide PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE INSTRUMENT
c DWP-98 Series Counting scale User s Guide PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE INSTRUMENT Specifications subject to change without prior notice CONTENTS 1. INSTALLATION
More informationSerial Dongle RS232 Plug&Scan
Programming guide Serial Dongle RS232 Plug&Scan Version 2.56 Important notice: Every effort is made to ensure the accuracy of our product information; however, we accept no responsibility for errors or
More informationNuscan 3200 Optical Laser Barcode Scanner
Nuscan 3200 Optical Laser Barcode Scanner Programming Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
More informationThis document hosted by: 10. OPTIONS
This document hosted by: www.oldwillknottscales.com 10. OPTIONS The following options are available for the FG series: OP-23 (FG-23) RS-232C serial interface OP-24 (FG-24) RS-232C serial interface and
More informationUser s Manual. MS140-3 or MS140I-3 Keyboard Wedge Slot Reader. PC Keyboard Wedge Setup Label
User s Manual MS140-3 or MS140I-3 Keyboard Wedge Slot Reader PC Keyboard Wedge Setup Label 1 Overview There are two models of the MS140 decoded slot reader available: The MS140-3 keyboard wedge slot reader
More informationDWP-PC SERIES PRICE COMPUTING SCALE User s Guide
DWP-PC SERIES PRICE COMPUTING SCALE User s Guide PLEASE READ THIS MANUAL VERY CAREFULLY BEFORE ATTEMPT TO OPERATE THE INSTRUMENT Specifications subject to change without prior notice CONTENTS 1. INSTALLATION
More informationTable of contents. Change scanner settings Factory default settings Default message format Programming flow chart
Table of contents Change scanner settings Factory default settings Default message format Programming flow chart 1. General 1.1 Open programming mode or Close programming mode with update 1.2 Close programming
More informationMS5100. Eclipse Series. User s Guide
MS5100 Eclipse Series User s Guide Disclaimer Honeywell International Inc. ( HII ) reserves the right to make changes in specifications and other information contained in this document without prior notice,
More informationOmni-Directional Barcode Scanner Model No. OM7120
Omni-Directional Barcode Scanner Model No. OM7120 User s Manual Programming with barcodes The BARCODE PROGRAMMING feature gives the possibility to change scanner settings without any tools or dismounting
More informationMS2421 / MS2422 / MS2431
MS2421 / MS2422 / MS2431 Bar Code Scanner Installation and User s Guide Disclaimer Honeywell International Inc. ( HII ) reserves the right to make changes in specifications and other information contained
More informationProgramming with barcodes
Configuration Guide Programming with barcodes The BARCODE PROGRAMMING feature gives the possibility to change the Scantech scanner settings without any tools or dismounting the scanner from the check stand.
More informationWinWedge Pro Validation Report
WinWedge Pro Validation Report Software: WinWedge Pro 4 Developer: TAL Technologies Inc. Initial Date: July 1996 Last Updated: April 2015 Revision: 4.0 Signatures Prepared by: Signature: Date: Approved
More informationHumidity Temperature Indicator. Instruction Manual
BT-RS1 Humidity Temperature Indicator Instruction Manual -2- GENERAL 3 DEFAULT SETTINGS 3 DESCRIPTION 3 Front Panel 4 Back Panel 4 Electrical Connections 4 OPERATION 5 Stand Alone Operation 5 PC Operation
More informationPioneer Stealth Touch S-Line (with integrated Epson printer) Installation and Configuration
One Blue Hill Plaza, 16th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Pioneer Stealth Touch S-Line (with integrated Epson printer)
More informationDNC2go
DNC2go Striker Systems P.O. Box 41 White House, TN 37188 Version 1.0.0.2 www.striker-systems.com Revision 8/2/2005 1 Contents Introduction... 3 Installing DNC2go... 4 Using DNC2go... 5 Setting up a Machine
More information2D Scan Engine Confguration Guide. 2D Barcode Scanner Configration Guide
2D Barcode Scanner Configration Guide 1 Table of Contents USB Settings USB Keyboard Mode...6 (A1) USB Downloader Mode...6 (A2) USB Virtual COM One Way Mode...6 (A3) USB Native Two Way Mode...6 (A4) USB
More informationUser Manual. August 2008 Revision 1.0. SKH300 ibutton Reader Configuration Utility
User Manual August 2008 Revision 1.0 SKH300 ibutton Reader Configuration Utility Copyright 2008 Jan. All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change
More informationCode Reader 1000/1400/8000 Configuration Guide
Code Reader 1000/1400/8000 Configuration Guide Code Reader 1000 Code Reader 1400 Code Reader 8000 1 Table of Contents USB Settings USB Keyboard Mode...6 (A1) USB Downloader Mode...6 (A2) USB Virtual COM
More informationActive Club POS Hardware Setup
Active Club POS Hardware Setup The Active Club POS hardware package includes the following (see figure 1): Heckler stand for ipad APG Vasario 1616 cash drawer Connecting cable for cash drawer Star Micronics
More informationBarcode BC-29. Decoder & Platform. Programming Manual
Barcode BC-29 Decoder & Platform Programming Manual CONTENTS Getting Started...2 Setting Procedures...3 Setting Flow Chart......4 Group 1 : Multi Validation....5 Group 2 : Hold Time...6 Group 3: Scan Mode
More informationManual de Programación
Manual de Programación SM2410, SM2410B, SM2420 y SM2430 ESPECIFICACIONES SUJETAS A CAMBIO SIN PREVIO AVISO. Enter/Exit Programming Mode (This barcode is also found at page 8.) IMPORTANT NOTICE Every effort
More informationNorth American Service Manual
North American Service Manual MODEL PC SERIES Version 2 March 25, 1997 Revision B1.1 April 4, 2000 Prepared by TRANSCELL TECHNOLOGY, INC. TABLE OF CONTENTS Page Chapter 1: Introduction... 1-1 Chapter 2:
More informationRS485 INSTRUCTION MANUAL. DM4500 Series. Page 1 of 6
RS485 INSTRUCTION MANUAL DM4500 Series Page 1 of 6 INDEX 1.1. RS485 OUTPUT...3 1.1.1. Introduction... 1.1.2. RS output menu diagram... Page 2 of 6 1.1 RS4 OUTPUT 1.1.1 Introduction The RS485 output option
More informationR1000 user manual. HID mode for IOS 1. Turn on the barcode reader, and read below barcodes sequence, the blue LED will flash rapidly.
HID Mode for IOS R10 user manual HID mode for IOS 1. Turn on the barcode reader, and read below barcodes sequence, the blue LED will flash rapidly. 2. the bluetooth of IOS to pair with the barcode reader.
More informationSCI Testers and Remote Communication: Using HyperTerminal
Testers and Remote Communication: Using HyperTerminal Introduction Programmable industrial equipment has long been a staple for automation in manufacturing environments. The capability to remotely program
More informationDLL2020. Software Configuration Manual
DLL2020 Software Configuration Manual DLL2020 SOFTWARE CONFIGURATION MANUAL DATALOGIC S.p.A. Via Candini 2 40012 - Lippo di Calderara di Reno Bologna - Italia DLL2020 Software Configuration Manual Ed.:02/2003
More informationMounting Dimensions / Viewing 2 Mounting Options 3. Wiring Configuration 4. Quick Set up Procedure 5. Changing Intensity 6.
Section Mounting Dimensions / Viewing 2 Mounting Options 3 Section 2 Wiring Configuration 4 Section 3 Quick Set up Procedure 5 Section 4 Changing Intensity 6 Section 5 Option Summary 7 Section 6 Option
More information2D Image Hands-Free Scanner
8072 1 Revision History Changes to the original manual are listed below: Version Date Description of Version 1.0 03/24/2016 Initial release i Important Notice No warranty of any kind is made in regard
More informationWireless Technology. BL 1000 Wireless Bar Code Scanner Developer s Guide Version 1.0
Wireless Technology BL 1000 Wireless Bar Code Scanner Developer s Guide Version 1.0 Important notice: Every effort is made to ensure the accuracy of our product information; however, we accept no responsibility
More informationSimple Start Instructions HI/Beckwith M-2001C Regulator Control
HI Document 2.4.72, Revision 0 Simple Start Instructions HI/Beckwith M-2001C Regulator Control Howard Industries Utility Products Division Howard Industries, Inc. 3225 Pendorff Road Laurel, MS 39440 Phone:
More informationDisclaimer. Please read through the manual carefully before using the product and operate it
ONEBRAND,ONESOLUTI ON 2D Handhel dbar codescanner UserManual Disclaimer Please read through the manual carefully before using the product and operate it according to the manual. It is advised that you
More informationDigital Torque Tester
YEAR WARRANTY (RESTRICTIONS APPLY) Imada, Inc. warrants its products to the original purchaser to be free from defects in workmanship and material under normal use and proper maintenance for two years
More informationProjectorNetTM Adapter Quick Start Guide
ProjectorNetTM Adapter Quick Start Guide Adapter networking 1. Quick Start The ProjectorNet Adapter kit contains the following items: ProjectorNet Serial to Ethernet Adapter Cable Adapter, ProjectorNet
More informationMETROLOGIC INSTRUMENTS, INC. MS9535 VoyagerBT Series Single-Line Hand Held Laser Scanner Installation and User's Guide
METROLOGIC INSTRUMENTS, INC. MS9535 VoyagerBT Series Single-Line Hand Held Laser Scanner Installation and User's Guide Copyright 2006 by Metrologic Instruments, Inc. All rights reserved. No part of this
More informationOperation & Installation Manual Serial Receiver Driver Model CP-SRD
92 53600 000-11 Operation & Installation Manual Serial Receiver Driver Model CP-SRD 92 53600 000 Table of Contents 1.0 Scope...1 2.0 Introduction...1 3.0 Specifications...1 4.0 Control Commands...2 5.0
More informationNCR Realscan 7837 High-Performance Scanners. User s Guide Issue A
NCR Realscan 7837 High-Performance Scanners User s Guide 497-0427357 Issue A Table of Contents Chapter 1 - Getting Started About This Manual... 1-1 Unpacking the Scanner... 1-2 RealScan 7837 High-Performance
More informationMETROLOGIC INSTRUMENTS, INC. MS9500 Voyager Series Single-Line Hand Held Laser Scanner Installation and User's Guide
METROLOGIC INSTRUMENTS, INC. MS9500 Voyager Series Single-Line Hand Held Laser Scanner Installation and User's Guide Copyright 2008 by Metrologic Instruments, Inc. All rights reserved. No part of this
More informationACE PLUS CORP. APCON100 series Operation Manual RS-232 to Ethernet Converter
APCON100 series Operation Manual RS-232 to Ethernet Converter Page 1 of 24 APCON100 series Operation Manual Index Chapter 1 Specifications 2 Chapter 2 Introduction 3 Chapter 3 Easy Installation 4 Chapter
More informationMobile POS Tablet. Barcode Scanner DATA CAPTURE MODULE OPERATION GUIDE. Peripheral Scanning Tool. To Connect Barcode Scanner Module
Barcode Scanner Follow below steps to check the scanner module with. 1. Click Start All Programs Utilities Peripheral Scanning Tool. 2. Select POS Tab. 3. Check the Scan Scanner from checkbox.. Press Auto
More informationUser s Manual WARNING. CIPHER 1160/1260 Bluetooth Wireless Scanner
CIPHER 1160/1260 Bluetooth Wireless Scanner User s Manual WARNING This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These
More informationPioneer Stealth Touch M5 Installation and Configuration
One Blue Hill Plaza, Second Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Pioneer Stealth Touch M5 Installation and Configuration This
More informationLaser Barcode Scanner Model no. LS6007 FS5027
Laser Barcode Scanner Model no. LS6007 FS5027 User s Manual FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
More informationPower Monitor / Power Monitor 51A. Quick guide to set up a connection with the Power Monitor devices through the Weidmüller Serial/Ethernet Converter
Power Monitor / Power Monitor 51A Quick guide to set up a connection with the Power Monitor devices through the Weidmüller Serial/Ethernet Converter 1.1 Revision history Version Date Change 0.0 11/2013
More informationQuick Start Guide. MS-3 Laser Scanner
Quick Start Guide MS-3 Laser Scanner This guide is designed to get your scanner up and running quickly. When connected to a host computer with Windows operating system (2000 or above), you can use ESP
More informationModels: TD3000 Series. Table Displays. 2 by 20 character display USER MANUAL
Models: TD3000 Series Table Displays 2 by 20 character display USER MANUAL i NOTICE The manufacturer of the POS table display makes no representations or warranties, either expressed or implied, by or
More informationTable of Contents. Introduction Installation Pin Assignments Method of Programming Setup Commands... 9
Table of Contents Introduction... 3 Installation... 4 Pin Assignments... 5 Method of Programming... 7 Setup Commands... 9 Interface selection... 10 Reading Mode... 11 RS 232 Communication Parameters...
More informationProduct Reference Guide
Model M260 www.e-seek.com 1 Model M260 2011 E-Seek Incorporated, All Rights Reserved. E-Seek reserves the right to make changes to any product to improve reliability, function, or design. E-Seek does
More informationUser Manual. PULSAR C CCD Hand-Held Scanner WARNING
WARNING PULSAR C CCD Hand-Held Scanner User Manual This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed
More informationSerial Connection of HC900 Hybrid Controller to 900CS Control Station
Note: Ethernet connections will provide faster performance than RS-485 HC900 1. Remove HC900 CPU and set S2 Dip Switches for RS-485 unterminated Replace CPU & follow instructions per Installation and User
More informationMS860 WiFi Bar Code Scanner
MS860 WiFi Bar Code Scanner TABLE of CONTENTS Introduction..................... 1 Introduction.................... 1 Quick Start.................... 2 Scanner Parts................... 5 Cradle Parts....................
More informationThermo Scientific VisionMate Wireless Barcode Reader User Manual
Thermo Scientific VisionMate Wireless Barcode Reader User Manual Version 01 User Manual September 2016 This page intentionally left blank Contents Overview 1-1 Package contents 2-1 Installation requirements
More informationQuick Start Guide. MS-3 Laser Scanner
Quick Start Guide MS-3 Laser Scanner This guide is designed to get your scanner up and running quickly. When connected to a host computer with Windows operating system (2000 or above), you can use ESP
More informationHVR LINE INSTALL GUIDE
HVR LINE INSTALL GUIDE 4.9.07 HVR v2.4.1 455 E. Industrial Drive P.O. Box 94 Hartland, WI 53029 Technical Support: 262.369.8798 Sales & Service: 262.369.8797 efax: 312.602.1356 www.visioncontrols.net Basic
More informationDTW 400/DTW Digital Torque Tester/Screwdriver User s Guide
DTW 400/DTW 405 - Digital Torque Tester/Screwdriver User s Guide LIST OF EQUIPMENT 1. Digital Torque Tester/Screwdriver (DTW 400 with CW and CCW ratchet (1/4 female hex) 2. 2 Phillips tips (DTW 405 with
More informationThis document courtesy of:
This document courtesy of: Data Weighing Systems, Inc. Contact Us For immediate assistance call 1-800-750-6842 Introduction Thank you for purchasing a Setra Super Count scale. Its ease of operation and
More informationDigital Torque Tester/Wrench
YEAR WARRANTY (RESTRICTIONS APPLY) Imada, Inc. warrants its products to the original purchaser to be free from defects in workmanship and material under normal use and proper maintenance for two years
More informationManual. Specifications. Contents. Options
Page 1 ATE-501: USB Input Controller - 8 Inputs The ATE-500/600 series is a range of modular I/O controllers. It uses small standardized boards which allows you to configure the system to your requirements.
More informationUserʼs Guide. 1200g High Precision Scale. 1200g High Precision Scale. Legal for Trade. Includes RS-232 interface port. UG Version 1.
Userʼs Guide 1200g High Precision Scale Legal for Trade 1200g High Precision Scale Includes RS-232 interface port UG Version 1.2_12-30-13 !!!! CALIBRATION WARNING!!!! Calibration AND inspection of calibration
More informationVIDEO MATRIX SWITCHER S MANUAL
VIDEO MATRIX SWITCHER S MANUAL Milestone s VIDEO MATRIX Switcher is a unit whereby multiple (2/4/8) VIDEO input can be switched to two (2) or multiple (simultaneous) VIDEO output or you can selected different
More informationC O N F I G U R A T I O N G U I D E
C O N F I G U R A T I O N G U I D E Copyright @ 2009, This manual is copyrighted, with all right reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced,
More informationAPPLICATION NOTE 4633 Bluetooth to 1-Wire Communication Using the DS9097U
Maxim > Design Support > Technical Documents > Application Notes > ibutton > APP 4633 Keywords: bluetooth, wireless, mobile, 1-Wire, alternative, Wi-Fi, radio, exchange, range, communication, SPP, serial,
More informationQuick Start Guide. MS-820 Industrial Bar Code Scanner
Quick Start Guide MS-820 Industrial Bar Code Scanner This guide is designed to get your scanner up and running quickly. When connected to a host computer with Windows operating system (98 or above), you
More informationInnovation By Design
Innovation By Design LAZERLOGIC LL2424 Programme Manual 01256 840927 @ sales@lazerlogic.com Kensington House, 21 Mill Road, Basingstoke, Hampshire RG24 9SN Enter/Exit Programming Mode ( represents the
More informationConfiguration for General DIP Devices. Setting Up RSLinx
Configuration for General DIP Devices Setting Up RSLinx Start Up RSLinx Program. Go to Communications Configure Drivers. Then, select an Available Driver Type (example, DeviceNet drivers). Once the appropriate
More informationLCD03 - I2C/Serial LCD Technical Documentation
LCD03 - I2C/Serial LCD Technical Documentation Pagina 1 di 5 Overview The I2C and serial display driver provides easy operation of a standard 20*4 LCD Text display. It requires only a 5v power supply and
More informationCode Reader 900FD Configuration Guide
Code Reader 900FD Configuration Guide 1 Table of Contents Reader Settings Save Settings...5 (A1) Reader ID and Firmware Version... 5 (A2) Feedback Settings Beep On...5 (A3) Beep Off...5 (A4) Targeting
More informationC O N F I G U R A T I O N G U I D E
C O N F I G U R A T I O N G U I D E Copyright @ 2013, This manual is copyrighted, with all right reserved. Under the copyright laws, this manual may not, in whole or in part, be copied, photocopied, reproduced,
More informationTPM Operation Manual
Revision 1.1 July 17, 2017 TPM Operation Manual Parameter setting, monitoring and auto data memory for MDC & ADC www.mountztorque.com - 1080 N 11th St - San Jose CA 95112-408.292.2214 1 Index 1. Main feature
More informationCCD Barcode Scanner User Manual
CCD Barcode Scanner User Manual Introduction This product is 1D CCD barcode scanner, also known as barcode reader or barcode gun scanner, is a technical equipment to read barcode information, by adopting
More informationCTI CALL INFORMATION INTERFACE
CTI CALL INFORMATION INTERFACE MODEL CN-4750 SERIAL/ITEM 533/nnn OPERATOR MANUAL Issue 3, FEB, 2002 AUTHOR: PETER ZEUG PATENTS PENDING DESIGNED AND MANUFACTURED IN AUSTRALIA DESIGN TWO THOUSAND PTY LTD
More informationSATA-IP Device Demo Instruction on AC701 Rev Apr-14
SATA-IP Device Demo Instruction on AC701 Rev1.0 11-Apr-14 This document describes SATA-IP Device evaluation procedure on AC701 using SATA-IP Device reference design bit-file. 1 Environment For real board
More informationUser's Manual CIPHER 1022 SERIES
User's CIPHER 1022 SERIES Document Number : 1022-52 Ver. 1.520 Release Date : Apr 22, 1996 1996, SYNTECH INFORMATION Co., Ltd.. All rights reserved. CipherLab is a registered trademark of SYNTECH INFORMATION
More informationData Capture System for Windows. Documentation. TSW Automation, Inc Robertson Ave. Nashville, TN phone: fax:
Data Capture System for Windows Documentation TSW Automation, Inc. 6115 Robertson Ave. Nashville, TN 37209 phone: 615-356-8785 fax: 615-356-8744 1995-1998 All rights reserved. SYSTEM OVERVIEW The Data
More informationENGINEERING G. M. B. H. ENGINEERING MAKES THE DIFFERENCE
ENGINEERING G. M. B. H. ENGINEERING MAKES THE DIFFERENCE CLERMONT-FERRAND-ALLEE 36 D-93049 REGENSBURG TEL 0941/29638 0, FAX 90 EMAIL info@bauer-eng.de INTERNET http://www.bauer-eng.de POF MPX (Plastic
More informationDigital Counting Scale. Revision 2.4 October 20, Transcell Technology, Inc. Contents subject to change without notice.
TC-2001 Series Digital Counting Scale Setup & Operation Manual Revision 2.4 October 20, 2003 2001-2003 Transcell Technology, Inc. Contents subject to change without notice. Transcell Technology, Inc. 975
More informationModel UD2A-EDID DVI Extender with EDID Management, Serial & GUI Control
Model UD2A-EDID DVI Extender with EDID Management, Serial & GUI Control UMA1148 Rev D Copyright 2008. Hall Research, Inc. All rights reserved. 1163 Warner Ave Tustin, CA 92780, Ph: (714)641-6607, Fax (714)641-6698
More informationDISCLAIMER. advanced PANMOBIL Systems GmbH & Co. KG. All rights reserved. International support contact:
DISCLAIMER advanced PANMOBIL Systems GmbH & Co. KG (here after called PANMOBIL) reserves the right to make changes in specification and other information contained in this document without prior notice
More informationDocking Station Operational Description
Docking Station Operational Description August 2018 Copyright 2017, 2018 All Rights Reserved Aures Technologies Changes: Ver 1.0, December 1, 2017, 1 st release Ver 1.1, January 11, 2018, add static IP
More informationManual 601: : USB/RS232. Specifications. Contents. Options
Page 1 ATE-601 601: : USB/RS232 I/O Controller - 8 Inputs, 4/8 Relays The ATE-500/600 series is a range of modular I/O controllers. It uses small standardized boards which allows you to configure the system
More informationVIA! SC-4 PROGRAMMING MANUAL
VIA! SC-4 PROGRAMMING MANUAL ELAN Home Systems 2001 All rights reserved P/N 40615-143-24 (A) TABLE OF CONTENTS SC-4 Programming Overview / VIA!Net Error Messages 3 PROGRAMMING THE SC-4..... 4-9 Introduction.
More informationFD-011WU. 2D Barcode Reader User Guide V1.6CC
FD-011WU 2D Barcode Reader User Guide V1.6CC Table of Contents 1 Getting Started... 1 1.1 Factory Defaults... 1 2 Communication Interfaces...2 2.1 TTL-232 Interface... 2 2.2 Baud Rate... 3 2.3 Data Bit
More information