Pioneer Stealth Touch M5 Installation and Configuration

Transcription

1 One Blue Hill Plaza, Second Floor, PO Box 1546 Pearl River, NY PC-AMERICA, (Voice) (Fax) Pioneer Stealth Touch M5 Installation and Configuration This document provides step-by-step instructions for setting up your Pioneer system, which contains the following components: the Stealth Touch M5 Terminal, the Integrated MSR, and the touchscreen monitor. 1 P age

2 Touchscreen Driver Installation The driver for the touchscreen monitor can be downloaded from: 1. Select Next. 2. Select Install PS/2 interface driver. 3. Select Next. 2 P age

3 4. Select OK. 5. Select Install RS232 interface driver. 6. Select Next. 7. Select Next System boot up. 8. Select Next. 3 P age

4 9. Select OK. 10. If you are using multiple monitors, select Support Multi- Monitor System. 11. Select Next. 12. Select Next. 4 P age

5 13. Select Next. 14. Select Yes, I want to restart my computer now. 15. Select Finish. 16. After the restart you should be presented with the screen to calibrate the monitor. Touch the center of each target to calibrate the monitor. If you do not then please see the next section. 5 P age

6 Calibrating the Touchscreen Monitor 1. Select the icon at the bottom right of the monitor (this will be located next to the date time on the taskbar). 2. Select the Tools tab, then select 4 Points Calibration. 3. You should be presented with the screen to calibrate the monitor. Touch the center of each target to calibrate the monitor. 4. When done select OK. 6 P age

7 MSR Configuration In order to work with pcamerica s software, all MSR s (magnetic swipe readers) need to read from track 2 only. When swiped into notepad a credit card should look like this (including the carriage return); ; = ? If when swiped in notepad the swipe looks like this; %B ^TEST CARD^ ? ; = ? It is reading from tracks 1 and 2, and the MSR needs to be configured to work with our software. Note: The Configuration for the MSR requires that a PS/2 keyboard be plugged into the port labeled below (make sure the unit is OFF when connecting the PS/2 keyboard): Note: For any configuration we will need to use the numbers above the characters on the keyboard ONLY! 7 P age

8 MSR Configuration - Enable Configuration Mode To enable configuration mode on your MSR we will need to open Notepad after connecting the MSR to the Computer. To open notepad and enable configuration mode follow the directions below: 1. Select Start. 2. Select All Programs. 3. Select Accessories. 4. Select Notepad. After Notepad has opened please press the following keys on your PS/2 Keyboard: CTRL+ALT+F10 You will now be in configuration mode. 8 P age

9 MSR Configuration - Carriage Return After entering the Configuration Mode (see: Enable Configuration Mode): Note: Only use the numbers on your keyboard above the characters (see: MSR Configuration). **** configuration mode **** 1:set interface 2:set magnetic string 3:set string editing 4:set buzzer 5:reset to default 6:show status ration 0:exit setup mode 1:set enable tracks 2:set require tracks 3:carriage return 4:transmit ss/es 5:caps lock 6:track output order 7:change carriage return code 8:output cr if read nothing 9:raw data output 0:back **** carriage return **** 1:don't send carriage return 2:after all tracks 3:after each track 4:after all data 0:back 1:set enable tracks 2:set require tracks 3:carriage return 4:transmit ss/es 5:caps lock 6:track output order 7:change carriage return code 8:output cr if read nothing 9:raw data output 0:back **** configuration mode **** 1:set interface 2:set magnetic string 3:set string editing 4:set buzzer 5:reset to default 6:show status 7:set keyboard configuration 0:exit setup mode 1. Select 2 on your keyboard to choose set magnetic string. 2. Select 3 on your keyboard to choose carriage return. 3. Select 3 on your keyboard to choose after each track. 4. Select 0 on your keyboard to choose back. 5. Select 0 on your keyboard to choose exit setup mode you should hear a long BEEP. 6. Exit Notepad. Note: You MUST exit the configuration mode and Notepad before performing any tests. 9 P age

10 MSR Configuration - Read Track 2 ONLY After entering the Configuration Mode (see: Enable Configuration Mode): Note: Only use the numbers on your keyboard above the characters (see: MSR Configuration). **** configuration mode **** 1:set interface 2:set magnetic string 3:set string editing 4:set buzzer 5:reset to default 6:show status ration 0:exit setup mode 1:set enable tracks 2:set require tracks 3:carriage return 4:transmit ss/es 5:caps lock 6:track output order 7:change carriage return code 8:output cr if read nothing 9:raw data output 0:back 3. Select 2 on your keyboard to choose track Select 2 on your keyboard to choose set magnetic string. 2. Select 1 on your keyboard to choose set enable tracks. 1:set enable tracks 2:set require tracks 3:carriage return 4:transmit ss/es 5:caps lock 6:track output order 7:change carriage return code 8:output cr if read nothing 9:raw data output 0:back **** configuration mode **** 1:set interface 2:set magnetic string 3:set string editing 4:set buzzer 5:reset to default 6:show status 7:set keyboard configuration 0:exit setup mode 4. Select 0 on your keyboard to choose back. 5. Select 0 on your keyboard to choose exit setup mode you should hear a long BEEP. 6. Exit Notepad. Note: You MUST exit the configuration mode and Notepad before performing any tests. 10 P age

11 Testing New Settings 1. Open Notepad. 2. Swipe the card through the attached MSR. 3. When swiped into notepad it should read like this (including the carriage return); ; = ? 11 P age