Assembly. Connection FEL 52 (E5) 3-wire DC connection (example) FEL 52 (E5) 0.5 A U V DC V DC

Transcription

1 Vibration Limit Switch Features Assembly Level limit switch for liquids Large selection of process connections: universal use Wide variety of electronic modules (e. g., relay, thyristor signal output): the right connection for every process control system No calibration: quick and low-cost start up No mechanically moving parts: maintenance-free, no wear, long operating life Monitoring of the vibrating fork for damage: guaranteed function PROFIBUS PA protocol: commissioning and maintenance quick and easy Up to SIL acc. to IEC 6508 Vibracon with plastic housing and process connection G** Vibracon with aluminium housing and process connection with flange Ø85 Ø80 max. 65 max. 55 L ~5 7.5 max. 76 max. 60 Function max. 7 The Vibracon is a level limit switch for use in all liquids. for temperature of -50 C ( K) to +50 C (4 K) for pressures up to 64 bar for viscosities up to 0000 mm²/s for densities up to 0.5 g/cm³ or 0.7 g/cm³ (other settings available on request) Additional dimensions see section dimensions. Length L see process connections. Ø.5 L max The function is not affected by flow, turbulence, bubbles, foam, vibration, bulk solids content or build-up, the Vibracon is thus the ideal substitute for float switches. The compact version is ideal for mounting in pipes (LVL-M). In addition there is a version with extension tube up to 6 m (0 ft) (LVL-M). High corrosion-resistant Alloy C4 (.460) is available for the vibration fork and process connection for applications in very aggressive liquids. EEx ia, EEx de and EEx d protection enable it to be used in hazardous areas. Connection Connection FEL 5 (E5) -wire DC connection (example) - preferably for use with memory programmable controls (PLC) - positive signal at the switch output of the electronics (PNP) - Output blocked on reaching limit level. - also in compact housing with plug connection available Other connection types see section electrical connection. 0.5 A FEL 5 (E5) (+) L+ L U... 0 V DC V DC e. g. relay PLC

2 Application Function principle Function and system design Measuring principle Input characteristics Measured variable Measurement range Medium density Output characteristics Fail-safe mode Switching time Switch-on response Auxiliary energy Supply voltage Limit detection maximum or minimum detection in tanks or pipelines containing liquids of any kind, even in hazardous areas The forks of the sensors vibrate at their intrinsic frequency. This frequency is reduced when covered with liquid. The change in frequency then activates the limit switch. limit level (limit value) LVL-M: depends on mounting point LVL-M: depends on mounting point and pipe extension up to 6000 mm (0 ft) adjustment on the electronic insert > 0,5 g/cm or > 0,7 g/cm (other on request) switch-over for minimum/maximum residual current safety on electronic insert MAX = maximum safety: The output switches to the power fail response when the fork is covered. for use with overspill protection for example MIN = minimum safety: The output switches to the power fail response when the fork is exposed. for use with dry running protection for example when fork is covered: approx. 0.5 s, when fork is exposed: approx..0 s (other switching times on request) additionally configurable for PROFIBUS PA (electronic insert FEL50A (PA)): s When switching on the power supply the output assumes the alarm signal. After max. s it assumes the correct switching mode. electronic insert FEL50A (PA): 9... V DC electronic insert FEL5 (AC): 5 V AC, 50/60 Hz electronic insert FEL5 (E5): V DC electronic insert FEL54 (WA): V AC, 50/60 Hz or V DC electronic insert FEL55 (SI):... 6 V DC, PLC electronic insert FEL56 (N), FEL58 (N): isolating amplifier acc. to EN (NAMUR) Connecting cable electronic inserts: cross section max..5 mm, lace in end splice in acc. with DIN 468 ground lead in housing: cross section max..5 mm external equipotential bonding: cross section 4 mm Power consumption electronic insert FEL5 (E5): max. 0.8 W electronic insert FEL54 (WA): max.. W Current consumption electronic insert FEL5 (E5): max. 5 ma Measurement accuracy Reference operating conditions ambient temperature: C (7.4 F), medium temperature: C (7.4 F), product density: g/cm (water), viscosity: mm /s, medium pressure p e : 0 bar, sensor mounting: vertical from above, density switch: to > 0.7 g/cm Maximum measured error max. ± mm, specified by mounting position Non-repeatability 0. mm Hysteresis approx. mm Influence of medium density max mm ( g/cm ) Influence of medium temperature max mm ( C ( F)) Influence of medium pressure max mm ( bar) Operating conditions Installation conditions Installation position LVL-M: any position LVL-M: with short pipe (up to 500 mm (9.7 inch)) any position, with long pipe vertical Ambient conditions Ambient temperature C (... 4 K), function with reduced data values see section ambient temperature Storage temperature C (... 5 K) Overvoltage protected electronic insert FEL5 (AC), electronic insert FEL5 (E5), electronic insert FEL54 (WA), electronic insert FEL55 (SI): overvoltage category III Process conditions Medium temperature C ( F), for exceptions see process connections Medium pressure p e = bar ( psi) over the entire temperature range, exceptions see process connections Test pressure max. 00 bar (.5 times the medium pressure p e ), no function during test pressure, burst pressure of diaphragm 00 bar Thermal shock resistance max. 0 C/s (max. 0 K/s) State of aggregation liquid Density min. 0.5 g/cm (compact housing 0.7 g/cm ), other density settings on request Viscosity max mm /s (max cst) Solid contents max. Ø 5 mm Mechanical specifications

3 Degree of protection Mechanical construction Construction type Dimensions Mass polyester, steel, and aluminum housing: IP66/IP67 compact housing: - IP65 with valve connector PG or /NPT - IP66/IP68 with M x connector without LEDs (.445/6L) - IP69K with M x connector with LEDs (.445/6L) LVL-M: compact design LVL-M: version with extension tube housing: diameter max. 85 mm, height max. 7 mm temperature separator, flameproof bushing: additional length L 40 mm process connection: length L mm extension: any length L from mm, depending on the process connection extension: length type II, for vertical installation from above same switching point as Vibracon LVL, LVL vibration fork: width 7.5 mm, fork width 0 mm, length 5 mm 600 g, basic weight: compact sensor, electronic insert, stainless steel housing, process connection G*, additional weight is dependent on extension tube, housing and process connection Additional weight process connections: - A* 000 g, A4* 00 g, A5* 500 g, A6* 400 g, A g, A g, A g, A g, A9.5 kg, A9 7. kg - C g, C5 00 g, C7 600 g, C75 00 g, C g, CA 5600 g - D g, D5 00 g, D7 600 g, D75 00 g, D7A 00 g, D7D 00 g, D g, DA 5600 g - F g, F5 00 g, F g, F6 400 g, F g, F7 600 g, F75 00 g, F7F 600 g, F8 400 g, F g, F g, F g, FA 5600 g, FA g - G* 00 g - J no information, J6 no information, J7 700 g, J9 no information, JA no information, JC 700 g - N* 00 g, N g - R* 00 g - T5 no information, T6 00 g extension tube, tempeprature spacers, flameproof bushings: - B* 900 g/m, C* 00 g/00 inch - D* 00 g - J* 900 g/m and 600 g, K* 00 g/00 inch and 600 g - L* 700 g - R* 900 g/m and 700 g, S* 00 g/00 inch and 700 g - T* 800 g Material wetted parts: - process connection and extension tube:.445/6l or.460/alloy C4 - vibration fork:.445/6l or.460/alloy C4 - flat seal for process connection G* or G*: elastomer fibre, asbestos-free housings: - polyester housing: PBT-FR with PBT-FR cover or with PA cover with sight glass, cover seal: EPDM - stainless steel housing:.445/6l, cover seal: silicone - aluminum housing: EN-AC-AlSi0Mg, plastic-coated, cover seal: EPDM - compact housing with valve connector or M connector:.445/6l cable gland: polyamide or brass, nickel-plated temperature spacer:.445/6l flameproof bushing:.445/6l Surface quality R a <. µm/80 grit: length, spacer, bushings *A, *B, *E Switching point see section switch point Process connection - cylindrical thread G/4A, GA to DIN ISO 8/ with flat seal to DIN conical thread R/4, R to DIN 999, part - conical thread /4NPT, NPT to ANSI B.0. - flush-mounted with welding sleeve to factory standard (G/4A, GA) - flush-mounted with welding neck to factory standard ( inch), sensor can be positioned - Triclamp -/ inch, inch to ISO 85 - flanges to EN 09- from DN5, to ANSI B 6.5 from inch, to JIS B 8 (RF) from DN5 For further information see type code. Indication and operation Display elements electronic inserts: - electronic inserts FEL50 A (PA), FEL58 (N): green LED, yellow LED - electronic inserts FEL5 (AC), FEL5 (E5), FEL54 (WA), FEL55 (SI), FEL56 (N): green LED, red LED compact housings: compact housing with valve connector - electronic version FEL5 (AC), FEL5 (E5): green LED, red LED - electronic version FEL58 (N): green LED, yellow LED compact housing with M x round connector without LEDs - electronic version FEL5 (E5): green LED, yellow LED, red LED - electronic version FEL58 (N): green LED, yellow LED compact housing with M x round connector with LEDs - electronic version FEL5 (E5): green LED, two yellow LEDs Control elements electronic insert FEL50A (PA): 8 switches for device address setting electronic inserts FEL5 (AC), FEL5 (E5), FEL54 (WA), FEL55 (SI), FEL56 (N): two switches for fail-safe mode and density change electronic insert FEL58 (N): two switches for fail-safe mode and density change and one test button interrupts lead

4 Function test Certificates and approvals Explosion-hazardous area compact housing: function test with test magnet electronic versions FEL5 (AC), FEL5 (E5) and FEL58 (N): During the test, the current state of the electronic switch is reversed. KEMA 0 AT 089, KEMA 0 AT 47 X, KEMA 0 AT 7, for additional certificates see Type of protection II /G EEx ia IIC T... T6 or EEx ia IIB T... T6 and II /D T80 C (KEMA 0 AT 089) II G EEx ia IIC T... T6 or EEx ia IIB T... T6 (KEMA 0 AT 47 X) II /G EEx d IIC T... T6 or EEx d IIB T... T6 (KEMA 0 AT 7) II G EEx na/nc II T6 and II D T85 C SIL classification up to SIL acc. to IEC 6508 Overspill protection Z (overspill protection in acc. with WHG) General information Directive conformity Directive 7//EEC EN 600- (Low Voltage Directive) Directive 89/6/EEC (EMC) emitted interference to EN 66, class B equipment noise immunity to EN 66, annex A (industrial sector) If the fork tines are joined together on account of build-up, the useful signal is attenuated to such an extent that the original EMC values can no longer be completely observed (EN electromagnetic fields, EN HF coupling). Directive 94/9/EC (AT) EN 5004, EN 5008, EN 50000, EN 5000, EN 5084, EN Conformity Electromagnetic compatibility NE Degree of protection EN 6059 Climate class EN 60068, part -8, fig. a Vibration resistance EN , Hz, 0.5 mm, 00 cycles Supplementary documentation Supplementary information technical information TI8O operating instructions KA4O () operating instructions KA0O (* with compact housing) operating instructions BA4O (electronic insert FEL50A (PA)) operating instructions KA40O weld-in socket G (LVL-Z0) operating instructions KA4O weld-in adapter G (LVL-Z0) operating instructions KA4O weld-in adapter G¾ (LVL-Z00) operating instructions KA5O sliding sleeve for unpressurised operation GA, NPT (LVL-Z0, LVL-Z) operating instructions KA5O sliding sleeve for unpressurised operation G½A, ½ NPT (LVL-Z, LVL- Z) operating instructions KA5O high pressure sliding sleeve GA, NPT (LVL-Z4, LVL-Z5, LVL-Z8, LVL-Z9) operating instructions KA54O high pressure sliding sleeve GA, NPT (LVL-Z6, LVL-Z7, LVL-Z0, LVL-Z) safety information SI0O (KEMA 0 AT 7) safety information SI06O (KEMA 0 AT 089) safety information SI064O (KEMA 0 AT 47 X) safety information SI54O (KEMA 0 AT 089), PROFIBUS PA version safety information SI59O (KEMA 0 AT 47 X), PROFIBUS PA version safety information SI8O ( II G EEx na/nc II T6 and II D T85 C) approval ZEO overspill protection acc. to WHG (Z ) FM installation drawing ZD04O CSA control drawing ZD04O EC-Type Examination Certificate, Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see Ambient temperature Permissible ambient temperature T at the housing depends on the product temperature T in the vessel: * additional temperature range for sensors with a temperature separator or pressure-tight bushing T T T * 70 C 50 C 0 C -50 C 0 C 50 C 00 C 50 C 90 C -50 C T 4

5 Switch point Switch point on the sensor depend on the mounting position, with reference to water, density g/cm³, C (96 K), p e 0 bar. Note: The switch points of the Vibracon LVL-MC are at other positions to those of the previous versions LVL, LVL. mm (0.5 in) 4 mm (0.6 in) 4 mm (0.6 in) Mounting from above Mounting from below Mounting from the side 5

6 Electrical connection Electronic insert FEL50A (PA) Two-wire connection for power supply and data transfer for connecting to PROFIBUS PA FEL50A (PA) Additional functions: Digital communication enables the representation, reading and editing of the following parameters: fork frequency, switch-on frequency, switch-off frequency, switch-on time and switch-off time, status, measured value, density switch. Matrix locking possible. Switch to WHG mode possible (WHG approval). You can also visit for more information. PA- PA+ PROFIBUS PA U 9 V DC... V DC Segment coupler Electronic insert FEL5 (AC) Two-wire AC connection Always connect in series with a load! FEL5 (AC) Check the following: the residual current in blocked state (up to.8 ma) that for low voltage - The voltage drop across the load is such that the minimum terminal voltage at the electronic insert (9 V) when blocked is not undershot. - The voltage drop across the electronics when switched through is observed (up to V). that a relay cannot de-energise with holding power below.8 ma If this is the case, a resistor should be connected parallel to the relay (RC module available on request). When selecting the relay, pay attention to the holding power/rated power (see connectable load). A min. 9 V L external load U~ max. 5 V AC, 50/60 Hz N N PE 6

7 Electrical connection Electronic FEL5 (AC) in compact housing Connection MAX MIN Housing C (½ NPT) or Housing C6 (PG) > 9 V > 9 V R R.0 A.0 A PE L (Ground) N PE L (Ground) N Electronic insert FEL5 (E5) Three-wire DC connection preferably used with programmable logic controllers (PLC), DI module as per EN 6-. positive signal at switching output of the electronics (PNP) Output blocked on reaching limit. FEL5 (E5) (+) 0.5 A e. g. relay PLC L+ L U 0 V DC 55 V DC Electronic FEL5 (E5) in compact housing Connection MAX MIN Housing C4 (M x ), connector with LEDs (WT) (BN) (WT) (BN) (BU) 4 (BK) (BU) 4 (BK) Housing C4 (M x ), connector without LEDs Housing C (½ NPT) or Housing C6 (PG) R R 0.5 A 0.5 A L L+ L L+ + + R R 0.5 A 0.5 A PE L L+ PE L (Ground) (Ground) L+ 7

8 Electrical connection Electronic insert FEL54 (WA) Universal current connection with relay output Power supply: Please note the different voltage ranges for AC and DC. Output: When connecting an instrument with high inductance, provide a spark arrester to protect the relay contact. A fine-wire fuse (depending on the load connected) protects the relay contact on short-circuiting. Both relay contacts switch simultaneously. FEL54 (WA) * When jumpered, the relay output works with NPN logic. * 0.5 A L L+ N L PE a u r a u r U~ 9 V AC 5 V AC, 50/60 Hz U 9 V DC 55 V DC Electronic insert FEL55 (SI) Two-wire connection for separate switching unit for connecting to programmable logic controllers (PLC) for example, AI module 4 ma... 0 ma to EN 6- Output signal jump from high to low current on limit (H-L edge) FEL55 (SI) EEx ia I U V DC 6 V DC e. g. PLC + 8

9 Electrical connection Electronic insert FEL56 (N) Two-wire connection for separate switching unit for connecting to isolating amplifiers acc. to NAMUR (IEC ), e. g. isolating amplifier KFD-SR-Ex.W or remote process interface KSD-BI-Ex from Pepperl+Fuchs Output signal jump from low to high current on limit (L-H edge) FEL56 (N) Connecting to multiplexer: set clock time to min. s. EEx ia I + Isolated switch amplifiers according to IEC (NAMUR) Electronic insert FEL58 (N) Two-wire connection for separate switching unit for connecting to isolating amplifiers acc. to NAMUR (IEC ), e. g. Isolating amplifier KFD-SR-Ex.W or remote process interface KSD-BI-Ex from Pepperl+Fuchs Output signal jump from high to low current on limit (H-L edge) FEL58 (N) Additional function: Test key on the electronic insert. Pressing the key breaks the connection to the isolating amplifier. Connecting to multiplexer: set clock time to min. s. EEx ia Note For Ex-d applications, the additional function can only be used if the housing is not exposed to an explosive atmosphere. I + Isolated switch amplifiers according to IEC (NAMUR) 9

10 Electrical connection Electronic FEL58 (N) in compact housing Connection MAX MIN Housing C4 (M x ), connector with LEDs (WT) (BN) (WT) (BN) (BU) 4 (BK) (BU) 4 (BK) Housing C4 (M x ), connector without LEDs + + Housing C (½ NPT) or Housing C4 (PG) + + 0

11 Dimensions Compact housing C* 0 40 Ø40 4 Ø40 AF AF * Stainless steel housing E* Ø76 max. 64 L max. 50 length L see process connections Process connections A**, C**, D**, F**, J**, N75 G* G* GE N* N* R* R* (66.5) (69) 50.5 (66.5) (69) 50.5 T** 66.5

12 Dimensions Extension tube Thread: G¾A GA Thread: ¾ NPT NPT R¾ R Flanges and flange-like process connections Vibration fork L Ø.5 L Ø.5 L Ø.5 from seal surface of thread adapter from lower egde of thread Ø.5 ~5 max

13 Accessories Welding sleeves LVL-Z00, welding sleeve G¾ for flush mounting for process connection G LVL-Z0, welding sleeve G for flush mounting for process connection GE LVL-Z0, welding sleeve G for flush mounting for process connection GE Flanges LVL-Z05, lap joint round flange DN50 PN40 form A with G thread for process connection G LVL-Z06, lap joint round flange ANSI " with G thread for process connection G LVL-Z07, lap joint square flange with G thread for process connection G Sliding sleeves LVL-Z0, sliding sleeve for unpressurised operation GA LVL-Z, sliding sleeve for unpressurised operation G½A LVL-Z, sliding sleeve for unpressurised operation NPT LVL-Z, sliding sleeve for unpressurised operation ½ NPT LVL-Z4, high pressure sliding sleeve GA LVL-Z5, high pressure sliding sleeve GA, Alloy C4/.460 LVL-Z6, high pressure sliding sleeve G½A LVL-Z7, high pressure sliding sleeve G½A, Alloy C4/.460 LVL-Z8, high pressure sliding sleeve NPT LVL-Z9, high pressure sliding sleeve NPT, Alloy C4/.460 LVL-Z0, high pressure sliding sleeve ½ NPT LVL-Z, high pressure sliding sleeve ½ NPT, Alloy C4/.460 Further accessories LVL-Z08, cover with glass sight glass for stainless steel housing E* LVL-Z09, cover with PC sight glass for stainless steel housing E* LVL-Z0, transparent cover for polyester housing P* V-G, mating connector, straight V-W, mating connector, 90 angled

14 Type code/model number L V L M Specification of length without unit for design M Certificates NA for non-hazardous areas WH WHG overspill protection E II G EEx ia IIC T6 E II /G EEx ia IIC T6 E II /G EEx d IIC T6 EA II G EEx ia IIC T6, WHG EB II /G EEx ia IIC T6, WHG EC II /G EEx d IIC T6, WHG EN II G EEx nc IIC T6, WHG EM II G EEx na IIC T6, WHG FI FM, IS, CI I, II, III, Div, Group AG FN FM, NI, CI I, Div, Group AD FX FM, XP, CI I, II, III, Div, Group AG CG CSA, General Purpose CI CSA, IS, CI I, II, III, Div, Group AG CX CSA, XP, CI I, II, III, Div, Group AG Optional equipment NA without optional equipment Z..B material, wetted parts.445, inspection certificate to EN 004 Electronic insert PA FEL50 A, PROFIBUS PA AC FEL5, contactless -wire switch, 9 V AC... 5 V AC E5 FEL5, PNP -wire, 0 V DC V DC WA FEL54, potential-free change-over contact, DPDT, 9 V AC... 5 V AC, 9 V DC V DC SI FEL55, 8/6 ma, V DC... 6 V DC N FEL56, NAMUR, L-H edge N FEL58, NAMUR with push button, H-L edge Housing, cable entry A aluminium housing, IP66, cable gland M0 A aluminium housing, Nema 4x, ¾ NPT A aluminium housing, IP66, entry G½A A4 aluminium housing, IP66, plug connector M x A5 aluminium housing, IP66, PA plug connector M x C compact housing, Nema 4x, ½ NPT plug connector,.445/6l C4 compact housing, IP66, plug connector M x,.445/6l C6 compact housing, IP66, PG plug connector,.445/6l E stainless steel housing, IP66, cable gland M0 E stainless steel housing, Nema 4x, ½ NPT E stainless steel housing, IP66, entry G½A E4 stainless steel housing, IP66, plug connector M x E5 stainless steel housing, IP66, PA plug connector M x P polyester housing, IP66, cable gland M0 P polyester housing, Nema 4x, ½ NPT P polyester housing, IP66, entry G½A P4 polyester housing, IP66, plug connector M x P5 polyester housing, IP66, PA plug connector M x Length, temperature spacer, pressure-tight bushing design M AA 66 mm/.6 in, R a <. µm/80 grit design M IA 66 mm/.6 in, R a <. µm/80 grit, with temperature spacer design M QA 66 mm/.6 in, R a <. µm/80 grit, with pressure-tight bushing design M BB mm L.445/6L, R a <. mm/80 grit design M BE mm L.460/Alloy C4, R a <. mm/80 grit design M CB in L.445/6L, R a <. mm/80 grit design M CE in L.460/Alloy C4, R a <. mm/80 grit design M DB special length L II,.445/6L, R a <. mm/80 grit, switch point = Vibracon compact design M DE special length L II,.460/Alloy C4, R a <. mm/80 grit, switch point = Vibracon compact design M JB mm L.445/6L, with temperature spacer design M JE mm L.460/Alloy C4, with temperature spacer design M KB in L.445/6L, with temperature spacer design M KE in L.460/Alloy C4, with temperature spacer design M LB special length L II,.445/6L, with temperature spacer, switch point = Vibracon compact design M LE special length L II,.460/Alloy C4, with temperature spacer, switch point = Vibracon compact design M RB mm L.445/6L, with pressure-tight bushing design M RE mm L.460/Alloy C4, with pressure-tight bushing design M SB in L.445/6L, with pressure-tight bushing design M SE in L.460/Alloy C4, with pressure-tight bushing design M TB special length L II,.445/6L, with pressure-tight bushing, switch point = Vibracon compact design M TE special length L II,.460/Alloy C4, with pressure-tight bushing, switch point = Vibracon compact Design M compact design M extended design (48 mm/6 in... 6,000 mm/0 ft) Continued on next page. 4

15 Type code/model number L V L M Process connection and material A ", ANSI B 6.5, 50 lbs RF,.445/6L A4 ¼", ANSI B 6.5, 50 lbs RF,.445/6L A4 ¼", ANSI B 6.5, 00 lbs RF,.445/6L design M A5 ½", ANSI B 6.5, 50 lbs RF,.445/6L A5 ½", ANSI B 6.5, 50 lbs RF,.445/6L design M A6 ", ANSI B 6.5, 50 lbs RF,.445/6L A6C ", ANSI B 6.5, 50 lbs RF, Alloy C4, platinised A6 ", ANSI B 6.5, 00 lbs RF,.445/6L design M A6 ", ANSI B 6.5, 600 lbs RF,.445/6L design M A7 ½", ANSI B 6.5, 00 lbs RF,.445/6L design M A8 ", ANSI B 6.5, 50 lbs RF,.445/6L A8 ", ANSI B 6.5, 00 lbs RF,.445/6L design M A9 4", ANSI B 6.5, 50 lbs RF,.445/6L A9 4", ANSI B 6.5, 00 lbs RF,.445/6L design M A9 4", ANSI B 6.5, 600 lbs RF,.445/6L design M F45 DN5 PN5/40 A, EN 09-,.445/6L F5 DN PN6 A, EN 09-,.445/6L F55 DN PN5/40 A, EN 09-,.445/6L F6 DN40 PN6 A, EN 09-,.445/6L F65 DN40 PN5/40 A, EN 09-,.445/6L F7 DN50 PN6 A, EN 09-,.445/6L F75 DN50 PN5/40 A, EN 09-,.445/6L F8 DN65 PN6 A, EN 09-,.445/6L F85 DN65 PN5/40 A, EN 09-,.445/6L F9 DN80 PN0/6 A, EN 09-,.445/6L F95 DN80 PN5/40 A, EN 09-,.445/6L FA DN00 PN0/6 A, EN 09-,.445/6L FA5 DN00 PN5/40 A, EN 09-,.445/6L D45 DN5 PN5/40 B, EN 09-,.445/6L C45 DN5 PN5/40, EN 09-,.460/Alloy C4,.445/6L, platinised D5 DN PN6 B, EN 09-,.445/6L C5 DN PN6, EN 09-,.460/Alloy C4,.445/6L, platinised D7 DN50 PN6 B, EN 09-,.445/6L C7 DN50 PN6, EN 09-,.460/Alloy C4,.445/6L, platinised D75 DN50 PN5/40 B, EN 09-,.445/6L C75 DN50 PN5/40, EN 09-,.460/Alloy C4,.445/6L, platinised D95 DN80 PN5/40 B, EN 09-,.445/6L C95 DN80 PN5/40, EN 09-,.460/Alloy C4,.445/6L, platinised DA DN00 PN0/6 B, EN 09-,.445/6L CA DN00 PN0/6, EN 09-,.460/Alloy C4,.445/6L, platinised F7F DN50 PN40 C, EN 09-,.445/6L N75 DN50 PN40 D, EN 09-,.445/6L RC R¾ BSP, DIN 999,.460/Alloy C4, platinised R R BSP, DIN 999,.445/6L RC R BSP, DIN 999,.460/Alloy C4 N ¾ NPT, ANSI B.0.,.445/6L NC ¾ NPT, ANSI B.0.,.460/Alloy C4 N NPT, ANSI B.0.,.445/6L NC NPT, ANSI B.0.,.460/Alloy C4 G G¾, DIN ISO 8/, BSP,.445/6L, mounting for welded sleeve design M GC G¾, DIN ISO 8/, BSP,.460/Alloy C4 G G, DIN ISO 8/, BSP,.445/6L GC G, DIN ISO 8/, BSP,.460/Alloy C4 GE G, DIN ISO 8/, BSP,.445/6L, mounting for welded sleeve J 0K 5A, JIS B 8 RF,.445/6L J6 0K 40A, JIS B 8 RF,.445/6L J7 0K 50A, JIS B 8 RF,.445/6L JC 0K 50A, JIS B 8 RF,.460/Alloy C4, platinised J9 0K 80A, JIS B 8 RF,.445/6L JA 0K 00A, JIS B 8 RF,.445/6L N75 DN50 PN40, EN 09-, groove,.445/6l T5 ½", DN5-8, Triclamp ISO 85,.445/6L T6 ", DN40-5, Triclamp ISO 85,.445/6L XXX special version Design M compact design M extended design (48 mm/6 in... 6,000 mm/0 ft) 5