AMCX429-x 4, 8, 16 or 32 Channel ARINC429 Test & Simulation Modules for PMC

Transcription

1 data sheet 4, 8, 16 or 32 Channel Test & Simulation Modules for PMC Avionics Databus Solutions

2 product guide 4, 8, 16 or 32 Channel Test & Simulation Modules for PMC General Features The is a member of AIM s next generation of PMC modules targeted to embedded applications. The offers full function test, simulation, monitoring and databus analyser capabilities and is available in configurations with 4, 8, 16 or 32 independent channels, fully software programmable for Receive (Rx) or Transmit (Tx) mode and configurable for high/ low bit rates. 4 channels are available on the AMCX429-4, 8 channels on the AMCX429-8, 16 channels on the AMCX module and 32 channels on the AMCX The AMCX429-4/ 8/ 16/ 32 also supports up to 8 discrete inputs and 8 discrete outputs which can be monitored or generated. The is designed to be installed on either a host carrier board to adapt to buses like standard PCI/ PCIe, VME/ VPX, cpci/ cpcie or on an embedded host computer. The modules use a high performance RISC processor with 128MB of Global RAM whereby all channels can operate concurrently at high or low bit rates with the intelligence to process data in real time. An onboard IRIG-B time encoder/ decoder provides a sinusoidal output and free wheeling mode for time tag synchronisation on the system level when using one or more or other AIM databus and network interfaces. Full function driver software is delivered with the cards in comprehensive Board Software Packages (BSP s) for different Operating Systems. The optional PBA.pro TM Databus Test & Analysis Tool (for Windows & Linux) can also be purchased for use with cards. Physical Interface on Front-and Rear-I/O Tx Channels General I/O Rx Channels Transmitter Receiver System-FPGA Bus Interface Unit (BIU) RISC Processor Encoder/ Decoder Block Diagram Boot-Up Flash IRIG-B Time Code Processor PCIe Interface PCIe to PCI Bridge PCI Bus Global RAM 128MB

3 Transmit Channel Operation modules provide real time simulation of up to 32 Transmitter Channels concurrently controlled by the onboard RISC Processor via instruction lists. Transmission rates are selectable for each channel at 12.5kbit/s or 100kbit/s with the associated rise/ fall time in accordance with the electrical specification. Cyclic/ Acyclic Label Transmission and Channel Loop Mode Error Injection for each Label Transfer: Short Gap, Parity, Bit Count, Coding Programmable Gap between Labels: 0 to 255Bit Simulate Zero-Jitter Scenarios using Virtual Label Transfers Multi-Buffering with Real Time Update supported per individual Label Transfer Reconstruction of previously recorded Traffic physically to the Bus with excellent Timing Accuracy (Physical Replay) Interrupt Generation on Label Transmit (configurable per Label Transfer) Receive Channel Operation modules provide real time monitoring of up to 32 Receiver Channels concurrently controlled by an onboard RISC Processor. Label Oriented Receive Mode (individual Buffers for each Label with Multi-Buffering and Real Time Updates) Chronological Receive Mode per Channel with 1μs Resolution Time Stamping Chronological Mode concurrent to Label Oriented Receive Mode Local (one Buffer per Channel) or Global Monitoring (one Buffer all Channels) Continuous or Single Shot Capturing Modes Support of SDI Handling Interrupt Generation on Label Reception (configurable per Label/ SDI) Complex Triggering and Filtering Functions Loop of received Data to configurable Transmit Channel with Label Data Modification Capability High Accuracy FPGA based Label Time Stamping Discretes modules provide up to eight General Purpose Discrete I/O s (GPIO s). GPIO s can be used as simple digital inputs/ outputs or to sample a digital output of an external system or to generate strobes to an external system. Loop-back & Pollution Mode Receive and Transmit Channels can be paired to form a Loop-back couple. Data received from the receiver channel are automatically transmitted on the selected transmitter channel with minimum delay. A special receiver Function Block mode can be used to modify (pollute) the received label prior to its re-transmission. Physical Bus Replay The cards can electrically reconstruct and replay previously recorded channels physically to the bus with excellent timing accuracy. Record files can be selected for Bus Replay. The additional capability to disable any or all labels from the replay enables smart systems integration and test to be performed. Physical Bus Interface cards have integrated line Transmitters/ Receivers and selectable transmission rate for each channel independently. All channels are available at the front plate output connector or at the Rear-I/O connector. IRIG-B Time Encoder/ Decoder cards include an onboard IRIG-B time encoder/ decoder with sinusoidal output and free-wheeling mode for time tag synchronisation. This allows synchronisation of multiple cards or any IRIG-B compatible modules to one common external IRIG-B time input source or to the onboard time code generator of one card as the reference for the correlation of data across multiple channels. Driver Software The Driver Software is supplied with the module. A full function Application Programming Interface (API) is provided compatible with Windows XP/Vista/7 and Linux. Host applications can be written in C and C++ or C#. A LabView/VI application interface is provided.

4 4, 8, 16 or 32 Channel Test & Simulation Modules for PMC AIM Office Contacts: AIM GmbH Sasbacher Str Freiburg Tel: Fax: sales@aim-online.com Vertriebsbüro München Terofalstrasse 23 a München Tel: Fax: salesgermany@aim-online.com AIM UK Cressex Enterprise Centre Lincoln Road High Wycombe Bucks, HP12 3RB UK Tel: Fax: salesuk@aim-online.com AIM-USA Seven Neshaminy Interplex Suite 211 Trevose, PA USA Tel: Toll Free: Fax: salesusa@aim-online.com Technical Data System Interface: 32-bit/ 66MHz capable PCIbus (Rev. 2.2) compliant Processors: One 400MHz RISC Processor Memory: 128MB Global RAM (DDR-RAM), 2x8-Mbit serial flash memory for BIU, 64-Mbit serial flash memory for LCA Encoder/Decoder: up to 32 Encoders/ Decoders with full error injection and detection Time Tagging: Sinusoidal 46-bit absolute IRIG-B Time stamping with 1μs resolution Trigger/ General Purpose Discretes: AMCX429-4/8/16: 4 Trigger Inputs and 4 Trigger Outputs 8 General Purpose Discrete Inputs 8 General Purpose Discrete Outputs (Discretes with avionics level for In and Out) All I/O s available on Front- and Rear-I/O connector AMCX429-32: 1 Trigger Output available on front connector Physical Bus Interface: Up to 32 Transmitters and 32 Line Receivers for a total of 32 Channels. All channels are user programmable RX or TX Connector: 68-pin, Mini D-Sub; Signals are also available at Rear-I/O connector; 3x Standard PMC Connectors; P11 and P12 for 32-bit PCI Bus; P14 for Rear I/O Dimensions: 149mm x 74mm Standard PMC Format Power Consumption: tbd. Operating Temp. Range: Standard 0 C C ambient Extended -40 C C ambient Conduction cooling available Storage Temp: -40 C C ambient Humidity: 0 to 95% non-condensing Ordering Information AMCX Channel PMC Module: 128MB Global RAM, 4 Trigger Inputs and 4 Trigger Outputs, 8 General Purpose Discrete In-and Outputs AMCX Channel PMC Module: 128MB Global RAM, 4 Trigger Inputs and 4 Trigger Outputs, 8 General Purpose Discrete In-and Outputs AMCX Channel PMC Module: 128MB Global RAM, 4Trigger Inputs and 4 Trigger Outputs, 8 General Purpose Discrete In-and Outputs AMCX Channel PMC Module: 128MB Global RAM, 1 Trigger Output on Rear-I/O, ACC-1 CompactPCI (3U) Carrier module with one PMC slot ACC-2 CompactPCI (6U) Carrier module with two PMC slots AVC-2 VME (6U) Carrier module with two PMC slots ACP-1 PCI Carrier module with one PMC slot For PCI/PCI - Express Carrier Modules with one PMC slot please contact the factory AIM GmbH _04June2012 Specifications are subject to change without notice.

5 product guide General Features The ACC-1 and ACC-2 are members of AIM s new family of 64bit extended PMC Carrier Boards. The ACC-1 is a single slot, single height (3U) CompactPCI module with one PMC slot to plug in a standard PMC module, whilst the ACC-2 is a single slot, double height (6U) CompactPCI module to plug in two standard PMC modules. Both implement a PCI-to-PCI Bridge using the industry standard INTEL device. The ACC-1 and ACC-2 fulfil the requirements of the CompactPCI specification as well as the requirements of the PCIbus standard both Primary and Secondary sides. The PMC-slot is in conformance with the Draft Standard Physical and Environmental Layers for PCI Mezzanine Cards (P1386.1/Draft 2.4). PMC Module Interface The ACC-1/ ACC-2 are designed to plug all standard PMC modules with a maximum PCIbus width of 64bit and a PCIbus operation up to 66 MHz. The ACC-1/ ACC-2 carrier board is of Universal I/O signaling voltage type and can be plugged in either a +3.3V or +5.0V CPCI chassis. On the secondary PCIbus side the PMC slot is configured to support +3.3V, I/O signaling voltage for use with +3.3V PMC modules. For +5.0V PMC modules the Carrier is identified by a different part number. The use of a voltage keying pin protects against false PMC assembly. Key Features Easily configured with any AIM PMC Databus Module: AFDX/ARINC664,, MIL-STD-1553 or any standard Third Party PMC module Mix and Match different Databus Modules with the ACC-2 Rear I/O available for ACC-2 66Mhz operation for +3.3V environments +5.0V signaling environment available 64 bit PCI bus extension Fully compliant to CompactPCI Specification Hosts PMC interface designed to PMC standard P1386.1/Draft 2.4 data sheet ACC-1/ACC-2 ACC-1 Generic Carrier Card ACC-1 ACC-2 Generic Carrier Card P12 (32 Bit) P11 (32 Bit) CompactPCI Generic Carrier Cards for PMC (PCIbus Mezzanine Card) modules P12 P11 J1 PMC 1 PMC 2 P14 (RIO) P13 (64 Bit) Seconary PCI-Bus (64 bit) Transparent PCI-to-PCI Bridge Intel CompactPCI Backplane (64 Bit) PMC Slot 1 (64 Bit) P13 J2 P22 (32 Bit) P21 (32 Bit) 3U and 6U CompactPCI Carrier Cards for PMC P24 (RIO) P23 (64 Bit) Seconary PCI-Bus (64 bit) ACC-2 Transparent PCI-to-PCI Bridge Intel J1 CompactPCI Backplane Rear IO 6U CompactPCI Backplane (64 Bit) Avionics Databus Solutions J2 J3 J3 PMC1 Rear-IO J5 J5 PMC2 Rear-IO

6 ACC-1/ACC-2 CPCI (3U and 6U) Generic Carrier Cards for PMC (PCIbus Mezzanine Card) modules AIM Office Contacts: AIM GmbH Sasbacher Str Freiburg Tel: Fax: sales@aim-online.com Vertriebsbüro München Terofalstrasse 23 a München Tel: Fax: salesgermany@aim-online.com Technical Data CPCI Interface Fully compliant to CompactPCI specification, PICMG 2.0 R3.0 Supports +5V and +3.3V signaling voltage CPCI Databus width of 32bit / 64bit CPCI Databus operation of up to 66MHz INTEL PCI-to-PCI Bridge Controller between CPCIbus and PCIbus PMC Interface ACC-1 Host Carrier board provides one PMC slot ACC-2 Host Carrier board provides two PMC slots Fully compliant to PCI Mezzanine card standardisation P / Draft 2.4 Supports +5V or +3.3V signaling voltage PMC Databus width of 32bit / 64bit PMC Databus operation of up to 66MHz PCI Bus Provides connections between CompactPCI Interface and the PMC slot/ slots Fully compliant to PCIbus Specification Rev 2.1 Supports either +5V or +3.3V VIO voltage, protected by PMC Keying Code PCIbus width of 32bit / 64bit PCIbus operation of up to 66MHz Priority based PCIbus Arbiter Connectors: CompactPCI: PMC: Connectors: CompactPCI: ACC-1 ACC-2 J1 Primary 32bit Bus / J2 Primary 64bit Bus P11 Secondary 32bit Bus / P12 Secondary 32bit Bus P13 Secondary 64bit Bus J1 Primary 32bit Bus / J2 Primary 64bit Bus J3 I/O (PMC 1) / J5 I/O (PMC 2) AIM UK Cressex Enterprise Centre Lincoln Road High Wycombe Bucks, HP12 3RB UK Tel: Fax: salesuk@aim-online.com PMC: Front Panel: Dimensions: P11 Secondary 32bit Bus / P12 Secondary 32bit Bus P13 Secondary 64bit Bus / P14 I/O P21 Secondary 32bit Bus / P22 Secondary 32bit Bus P23 Secondary 64 bit Bus / P24 I/O PMC-Bezel standard Breakout ACC-1: 3U Board: 100mm x 160mm ACC-2: 6U Board: 233mm x 160mm AIM-USA Seven Neshaminy Interplex Suite 211 Trevose PA USA Tel: Toll Free: Fax: salesusa@aim-online.com Power Dissipation: ACC-1: 2.2 Watt maximum: full BusLoad (excludes PMC dissipation) ACC-2: 2.2 Watt maximum: full BusLoad (excludes PMC dissipation) Temperature: 0 to +70 C Standard Operating -15 to +85 C Extended Temperature -55 to +125 C Storage Humidity: 5 to 95% non-condensing Ordering Information ACC-1: CPCI (3U) Carrier Module with one PMC slot ACC-1-5V: CPCI (3U) Carrier Module with one PMC slot (5V version) ACC-2: CPCI (6U) Carrier Module with two PMC slots ACC-2-5V: CPCI (6U) Carrier Module with two PMC slots (5V version) AIM GmbH 11/2010 Specifications are subject to change without notice.