4. Enter LOCATION CODE 4.1 From LOCATION CODE screen press CHANGE button. Arrow points to first digit
|
|
- Elvin Reeves
- 5 years ago
- Views:
Transcription
1 6000 BIRD DOG PLUS STANDARD TEST PROCEDURE FOR SINGLE ELEMENT METER CIRCUIT TESTING ONLY (Save ONLY the GLOB SAVE Screen Forms 3, 4, 5, 6, 8, 9 Meter Circuits) 1. Hookup Probes to Phase A (or B or C as appropriate) 1.1 Primary Current: Flex Coil--Arrow towards load, High Voltage--Large Dot Toward Line 1.2 Secondary Current: Duckbill / Copper side up (Use only phase A duckbill with the large knob on the 3 Phase Connector Box set to Duckbills and the small knob set to either Flexible Coil or High Voltage.) 1.3 Secondary Voltage: Alligator Clips /Red to phase A (or B or C), Black to phase C (Connect to phase C on the lug above the switch & leave it there for the entire test.), and white to neutral/low side. (Leave Yellow (or green for older units) alligator clip unconnected.) 1.4 Confirm Proper Voltage Wiring from the Test Switch to the Meter (Skip this section if using Meter Base Adapters.) Short phase B & C CTs and confirm the meter is reporting phase A Short phase A & C CTs and confirm the meter is reporting phase B Short phase A & B CTs and confirm the meter is reporting phase C Close all CT shorting switches 2. Turn the Bird Dog Plus On 3. Enter Meter/Circuit/Rotation 3.1 If listed data is the same as your circuit: press YES and go to If listed data is different than your circuit: press NO, select correct data and go to If your circuit is not known or irrelevant: press UNDEFINED and go to Enter LOCATION CODE 4.1 From LOCATION CODE screen press CHANGE button. Arrow points to first digit 4.2 Press the CLEAR button 4.3 Cycle the far left button 0-9, A-Z+ until the desired digit appears 4.4 Press the MORE button 4.5 Press NXT DIGIT. Arrow advances to next digit. Takes you back to previous screen 4.6 Repeat 4.3 through 4.6 until new location code entered 4.7 When the new location code is entered, press the MORE button twice 4.8 Press the SAVE to store new LOCATION CODE and go to the MAIN MENU 5. Review the WIRE VERIFY GRAPH & Run the RATIO/BURDEN TEST 5.1 Select WV GRAPH from the MAIN MENU the bottom right button 5.2 Select PHASE A (or B or C) 5.3 Review the readings as follows: 1
2 Primary Current OK? (>10% of rated ratio, steady) Secondary Voltage OK? (Correct value, steady) Secondary Current OK? (>0.5 Amps, steady, balanced) True PF OK? (>0.7, steady) Phase Angles OK? (steady, adjust for inherent phase shift) THD Voltage--OK (<5.0%, steady) THD Current--OK (<20.0%, steady) 5.4 Select EXIT 5.5 Select CT RATIO/BURDEN TEST 5.6 Select PHASE A (or B or C) 6. Review Results of CT Ratio/Burden Test WIRE VERIFY--OK? (Correct/See Graph) RATIO (NO BURDEN) OK? (within 2% of Rated Ratio) BURDEN--OK? (As Rated/Error ohms) 6.1 If you need to troubleshoot, go to appropriate choice and press SELECT to proceed 6.2 If all OK, press MORE OPTN 6.3 Press GLOB SAVE (Save ONLY the GLOB SAVE Screen) 6.4 Press STORE 6.5 You have now finished Phase A (or B or C); if C, go to Step 8 7. Move Probes to the Next Phase 7.1 Currently in CT BURDEN AND RATIO screen 7.2 Press R&B MENU 7.3 Go back to Step 5.2 and repeat through Step If you are also performing a Simultaneous 3 Phase Meter Verify Test, go to the next section of this Standard Test Procedure and follow the meter testing steps. If not, Wrap Up on Step Wrap Up Procedure--After testing, turn off Bird Dog Plus, leaving cables connected. Coil secondary voltage and current cables together into case, and then coil the flexible coil into the case and close flap. Move to the next site. 2
3 6000 BIRD DOG PLUS SCREEN FLOW FOR SINGLE ELEMENT METER CIRCUIT TESTING Step 1.1 Hook up the Flexible Coil Probe or the High Voltage Probe like this: Step 3.1 Select NO if this is not the correct meter type & rotation. Step 3.2 Select the correct meter type & rotation. Step 3.2 If you are incorrect as to the rotation, you will see the following message. Press the YES button: Step 3.2 Confirm the meter type & rotation selected. 3
4 Step 4.1 Press the CHANGE button. Step 4.2 Press the CLEAR button. Step 4.3 Press the 0-9, A-Z+ button to start the first digit. Step 4.4 Press the MORE button. Step 4.5 Press the NEXT DGT button. Step 4.6 Repeat the steps above until the entire LOCATION CODE is entered. 4
5 Step 4.8 Press the SAVE button and you will be taken to the MAIN MENU. Step 5.1 SELECT WV GRAPH the bottom right button. Step 5.2 Select the PHASE you are testing. Steps 5.3 Review the wire verify graph for appropriate readings & press EXIT. Proper Wiring Bad Hook Up or Cross Wired Circuit Leads Reversed or Duckbill Backwards Step 5.5 Select CT RATIO/BURDEN TEST. 5
6 Step 5.6 Select the PHASE you are testing. Steps Review the CT BURDEN AND RATIO screen for appropriate readings. Press the MORE OPTN button. Step 6.3 Press the GLOB SAVE button and the following screen will appear. Step 6.4 Press the STORE button. Steps 6.5 & 7.1 You are automatically taken back to the CT BURDEN AND RATIO screen. Press the R+B MENU button. Step 7.2 Select the WIRE VERIFY GRAPH go back to Step 5.2 & test the next phase. 6
7 STANDARD TEST PROCEDURE FOR 6000 BIRD DOG PLUS SIMULTANEOUS 3 PHASE METER VERIFICATION TESTING AFTER A METER CIRCUIT TEST 1. Hookup Probes to Phase A (or B or C as appropriate) & Sensors to the Meter 1.1 Secondary Current: Depending upon the type of circuit you are testing, there will be different hookup procedures. See Section F.3.2 for more detailed hookup procedures: Forms 3, 5, 6, 8, & 9 Circuits with a Test Switch: Duckbills / Copper side up or clamp-on CTs (Small I Probes) Forms 4 Circuits with a Test Switch: Duckbills / Copper side up for phase 1 and silver side up for phase 2, or clamp-on CTs (Small I Probes) with reverse direction for phase Secondary Voltage: Alligator Clips /Red to phase A, yellow (or green for older units) to phase B, black to phase C, & white to neutral/low side. 1.3 Automatic Sensors: Attach the automatic sensors to the meter Phase Connector Box: Set the 1) Small Knob to the Meter Verify position, 2) the Large Knob to the proper probes (Large I Probes or Small I Probes or Duckbill connectors) you are using, and 3) the Meter Trigger switch set to Sensors. 2. Transition From Meter Circuit Testing to Meter Testing 2.1 From the CT RATIO AND BURDEN screen, press the MORE OPTN button. 2.2 Press PP GRAPH. 2.3 With the 6000 on, change the setting on the small knob to Meter Verify. Change the setting on the large knob if necessary. Press CONTINUE. 3. Review the POLYPHASE GRAPH for Input Signals 3.1 Review the AMPLITUDE readings 3.2 Press NEXT VIEW and scroll through PHASE (DEG) angles, HARMONIC DISTORTION readings, and then finally the SYSTEM POWER SUMMARY screen for anomalous readings as shown below: 3.3 Press MV MENU when your review is complete Secondary Currents OK? (>0.5 Amps, steady, balanced) Phase Angles OK? (steady, adjust for inherent phase shift) THD Readings THDV < 5% & THDI < 20% System Power Readings True PF OK? (>0.7, steady) Secondary Voltages OK? (Correct value, steady) 4. Perform the Meter Verification Test 4.1 From the METER VERIFY TEST menu select METER VERIFY ONLY 4.2 Enter the appropriate Kh and press SELECT 4.3 INPUT NUMBER OF PULSES PER REVOLTION for which the meter is set 4.4 Now setup your sensors on the SENSOR SETUP screen 4.5 Once the sensors are detecting a proper pulse or rotation, press the AUTOMATIC button 4.6 The Bird Dog Plus will now detect the length of time for the test and will bring you to the TIMING RESULTS screen 7
8 4.7 Press the START button (or wait 5 seconds). Once the sensor sees a pulse or a disk rotation, the test will begin. The test will automatically stop once the final revolution or pulse is detected. 5. Review Results of Meter Verify Test & Save Results 5.1 Insure that the accuracy is within your tolerance specification. Test Time > 30 Seconds? Accuracy OK? 5.2 Press the MV SAVE button 5.3 Press STORE if all is OK. Press ABORT if a correction is needed 5.4 You have now finished testing the accuracy of the entire meter (all 3 phases) and storing the data in memory. 6. Wrap Up Procedure--After testing, turn off Bird Dog Plus, leaving cables connected. Coil secondary voltage and current probes into their appropriate compartments. Then coil the sensors and put them in their compartment. Close the case lid. You are done. 98
9 SCREEN FLOW FOR 6000 BIRD DOG PLUS SIMULTANEOUS 3 PHASE METER VERIFICATION TESTING AFTER A METER CIRCUIT TEST Step 2.1--After testing the meter circuit, you should be on the following screen. Press the MORE OPTN button once. Step 2.2--Now press PP GRAPH. Step 2.3--A message screen appears asking you to change your switch settings on the small knob on the 3 Phase Connector Box to Meter Verify. Then press the CONTINUE button. Steps Review the AMPLITUDE readings. Press NEXT VIEW and scroll through PHASE (DEG) angles, HARMONIC DISTORTION readings, and then finally the SYSTEM POWER SUMMARY screens. Then press MV MENU. Make sure on the PHASE (DEG) screen that you don t have reversed phases! 9
10 Step 4.1 SELECT the METER VERIFY ONLY. Step 4.2 Select the appropriate Kh value. Step 4.3 Select the NUMBER OF PULSES PER REVOLUTION & press ACCEPT. Steps 4.4 & 4.5 Setup your sensors and press AUTOMATIC. Step 4.6 The Bird Dog Plus will now detect the length of time for the test and will bring you to the TIMING RESULTS screen Step 4.7 Press the START button. 910
11 Step 4.7 Once the sensor sees a pulse or a disk rotation, the test will begin. The test will automatically stop once the final revolution or pulse is detected. Steps 5.1 & 5.2 Review the METER VERIFICATION screen for proper ACCURACY & press the MV SAVE button. Step 5.3 Press the STORE button. Step 5.4--You have now finished testing the accuracy of the entire meter (all 3 phases) and storing the data in memory. 911
4. Enter LOCATION CODE 4.1 From LOCATION CODE screen press CHANGE button. Arrow points to first digit
5000 BIRD DOG PLUS STANDARD TEST PROCEDURE FOR SINGLE ELEMENT METER CIRCUIT TESTING ONLY (Save ONLY the GLOB SAVE Screen Forms 3, 4, 5, 6, 8, 9 Meter Circuits) 1. Hookup Probes to Phase A (or B or C as
More informationPZ4000 Product Tutorial. Product Tutorial
PZ4000 HIGH FREQUENCY POWER ANALYZER PZ4000 POWER ANALYZER MEASUREMENT LAB OVERVIEW & OBJECTIVES The following is a basic demo procedure for the PZ4000 Power Analyzer. This demo uses the power meter s
More informationSpinGraph 5000-SG1 SpinGraph SE 6000-SGl SpinGraph Deluxe. Installation and Instruction Manual
SpinGraph 5000-SG1 SpinGraph SE 6000-SGl SpinGraph Deluxe SpinGraph SE SpinGraph Deluxe Manual Version 5.4 December 15, 2008 Installation and Instruction Manual Spinlab Utility Instrumentation, Inc 3110
More informationDPM Active Harmonic Filter Quick Start Instructions
DPM Active Harmonic Filter Quick Start Instructions These instructions will guide you through installing, testing your installation, and starting up your DPM. For additional information please refer to
More informationpower quality Models 8230 & 8220
power quality Analyzer & METER Models 8230 & 8220 Measures up to 660Vrms or Vdc Measures current up to 6500Aac or 1400Adc Measures inrush current Displays Min, Max and Average Volts and Amps, Crest Factor,
More informationThree-Phase Power Quality Analyzer PowerPad Model 3945
Three-Phase Power Quality Analyzer PowerPad Model 3945 Wouldn t it be nice if you could look inside your electrical system and see what s going on? Troubleshooting would be so much easier if you could
More informationTroubleshooting guide for the S100 Energy meter and EPS
Troubleshooting guide for the S100 Energy meter and EPS The S100 Energy Meter is the brains of the Sungrow hybrid system. It tells the inverter when to charge or discharge the battery, when to go into
More informationAEE MAKERSPACE: TROUBLESHOOTING 101
AEE MAKERSPACE: TROUBLESHOOTING 101 DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING MICHIGAN STATE UNIVERSITY I. TITLE: Lesson 02: Elenco M-2666K DC Testing and Calibration II. PURPOSE: This lab will
More informationDRTS 33. The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters
The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters Testing all relay technologies: electromechanical, solid state, numerical and IEC61850 Manual
More informationWE-30. Portable Three-Phase Meter Tester/Analyzer
Portable Three-Phase Meter Tester/Analyzer WE-30 333 Crosspark Drive Pearl, Mississippi 39208 USA P: 601.933.0900 F: 601.933.0901 E: sales@watthour.com www.watthour.com Portable Three-Phase Meter Tester/Analyzer
More informationDRTS 64. The new generation of advanced test equipment for Relays, Energy meters, Transducers and Power quality meters.
The new generation of advanced test equipment for Relays, Energy meters, Transducers and Power quality meters Testing all relay technologies: electromechanical, solid state, numerical and IEC61850 Manual
More informationDRTS 33. The new generation of advanced three phase relay test set
The new generation of advanced three phase relay test set Testing all relay technologies: electromechanical, solid state, numerical and IEC61850 Local control with color display Simultaneously available:
More informationPIECAL 322 Automated Thermocouple Calibrator Operating Instructions. Product Description. Practical Instrument Electronics
PIECAL 322 Automated Thermocouple Calibrator Operating Instructions Product Description Easy to use With the PIECAL 322-1 you can check & calibrate all your thermocouple instruments and measure thermocouple
More informationRGM180 Display Series
Quick Start Guide RGM180 Display Series BG0509 REV.A2 RGM180 QUICKSTART LIMITED WARRANTY The manufacturer offers the customer a 24-month functional warranty on the instrument for faulty workmanship or
More informationThree-Phase Power Quality Analyzer PowerPad Model 3945-B
Three-Phase Power Quality Analyzer PowerPad Model 3945-B Display and record waveforms, transients, trend data and events simultaneously! Wouldn t it be nice if you could look inside your electrical system
More informationPortable Three-Phase Meter Site Analyzer
Three-Phase Customer Load Field Testing Portable Three-Phase Meter Site Analyzer Radian Research Reference Standard Accuracy Proven Portable Three-Phase Meter Site Analyzer RW-30X NS RW-31X NS tests,
More informationNotes: LOADMAN. for Logging Trucks TABLE OF CONTENTS BUNK 2 CAL NUMBERS BUNK 1 CAL NUMBERS LB2 SPAN LB2 ZERO RB2 SPAN RB2 ZERO
Notes: It is recommended after you calibrate your scale with the TARE, ZERO, and SPAN, calibration functions, that you go into the TROUBLESHOOT Mode and record all Calibratoin Numbers to aid your effort
More informationHow to Conduct an Energy Audit Using the Energy Platform EP1
White Paper How to Conduct an Energy Audit Using the Energy Platform EP1 Introduction Sophisticated energy analyzers introduced in the 80s were able to trend and record energy usage and help identify when,
More informationWorking Standard Model WS 2320
Working Standard Model WS 2320 Version 4.4 1. How to 1.1 Accessories There are 6 connectors in Working Standard (WS) body, located top and bottom. These options divide all accessories into 4 categories:
More informationABB Digital medium-voltage switchgear
NAMIBIA AMEU/AEDU MARCH 2018 ABB Digital medium-voltage switchgear Barry Addinall UniGear Digital Contents 1. Digital switchgear 2. Complexity of Distribution networks 3. New technologies using digital
More informationDRTS 66. The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters
The new generation of advanced test equipments for Relays, Energy meters, Transducers and Power quality meters Testing all relay technologies: electromechanical, solid state, numerical and IEC61850 Manual
More informationOperation Manual for USB Autoscope Lite. Contents. USB Autoscope Lite Operation Manual
Operation Manual for USB Autoscope Lite Please read this manual thoroughly before attempting to operate the device. Contents 1. Purpose...2 2. Technical characteristics of the USB Autoscope Lite...2 2.1
More informationMODEL 3010 PORTABLE AUTOMATED TEST KIT P.A.T.
333 CROSSPARK DRIVE PEARL, MS 39208 Phone: (601) 933-0900 Fax: (601) 933-0901 MODEL 3010 PORTABLE AUTOMATED TEST KIT P.A.T. OPERATIONS MANUAL REV 1.3 W A R N I N G Safety is of utmost concern to Watthour
More informationW Warning To avoid electrical shock, remove test leads and any input signals from the Model 707 Loop Calibrator before opening the case.
Model 707 Loop Calibrator W Warning To avoid electrical shock, remove test leads and any input signals from the Model 707 Loop Calibrator before opening the case. WCaution The Model 707 Loop Calibrator
More informationPortable Three-Phase Meter Site Source Analyzer
Three-Phase Field Testing Portable Three-Phase Meter Site Source Analyzer Radian Research Reference Standard Accuracy Proven Portable Three-Phase Meter Site Source Analyzer RW-30X RW-31X the meter with
More informationOPERATING AND SERVICE MANUAL SPECIAL SUPPLEMENT
OPERATING AND SERVICE MANUAL SPECIAL SUPPLEMENT 11683A OPTION H01 POWER METER RANGE CALIBRATOR 11683-90010 Model Number: 11683A Option H01 Part Number: 11683-90010 Date Printed: June 5, 2012 2 11683A Option
More informationDRTS 3 PLUS Advanced Protection Relay Test Set and Measurement System
Advanced Protection Relay Test Set and Measurement System Multi-tasking equipment designed for testing protection relays, energy meters, transducers Particularly designed to test RTU (remote terminal unit)
More informationWT1800 PRECISION POWER ANALYZER
PRECISION POWER ANALYZER Page 1 Page 2 PRODUCT TUTORIAL Table of Contents: A.) Overview & Objectives... B.) Power Meter Connections.. C.) Basic Setup for Power Measurement Initialize Settings Setting Wiring
More informationPOWER & ENERGY LOGGER MODEL PEL 102 & PEL 103
POWER & EERGY LOGGER MODEL PEL 102 & PEL 103 Quick Start Guide EGLISH www.aemc.com CHAUVI AROUX GROUP Statement of Compliance Chauvin Arnoux, Inc. d.b.a. AEMC Instruments certifies that this instrument
More informationBC-9000 Field Calibration Procedure CF1_FIELDCAL_BC9000 Revised 03/16/2013
BC-9000 Field Calibration Procedure CF1_FIELDCAL_BC9000 Revised 03/16/2013 INTRODUCTION: The BC-9000 Battery Charger will recharge12 and 24 volt lead-acid and nickel cadmium batteries. Battery charging
More informationThese are the illustrated step-by-step guidelines for upgrading your Quad 306 with the Dada Electronics upgrade-kit.
Quad 306 DIY illustrated guidelines version 1.1 These are the illustrated step-by-step guidelines for upgrading your Quad 306 with the Dada Electronics upgrade-kit. We will replace all electrolytic capacitors,
More informationDENT Instruments ELITEpro Mobile App
DENT Instruments ELITEpro Mobile App Version 3.0 Instruction Guide Revision: Final Draft May 20, 2015 Page 2 of 16 Instruction Guide: ELITEpro Mobile App 2015 DENT Instruments, Inc. All rights reserved.
More informationPower Factor Controller
Elnet LTC Power Factor Controller Table of Contents CHAPTER 1 Electrical Wiring...3 1.1 Electrical Connections...3 1.2 Electrical Wiring Diagrams...5 1.3 Indication Leds...7 1.4 Test Capacitors Screen...8
More informationPQ-Box 100, 150, 200 & 300 Power Quality Analyser Clamps & Accessories
Mini Clamps: Part Number 111.7015 PQ-Box 100, 150, 200 & 300 Power Quality Analyser Clamps & Accessories Description 10 ma-to-20 A or 100 ma-to-200 A. Switchable range mini clamp. 40 Hz 20 khz 4 x mini
More informationINSTALLATION DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER. Before installation:
DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER The DKM-409 is a precision instrument designed for displaying various AC parameters in 3-phase distribution panels. Thanks to its isolated
More informationthe Interactive Catalog
Interactive Catalog Supplements Catalog PDFs If you need detailed product information, or help choosing the right product for your application, see our Interactive Catalog Use the Interactive Catalog to
More informationHAND-HELD THERMOCOUPLE THERMOMETER SERVICE MANUAL. CATALOG NUMBERS , and , and PROPRIETARY
HAND-HELD THERMOCOUPLE THERMOMETER SERVICE MANUAL CATALOG NUMBERS 600-1000, 600-1010 and 600-1020 91100-00, 91100-10 and 91100-20 PROPRIETARY Information contained in this manual is proprietary to COLE-PARMER
More informationModel POWER QUALITY ANALYZERS, METERS & LOGGERS Power Quality Meter
Special product features '''' ENERGY METER ''' MEASURES RPM POWER QUALITY ANALYZERS, METERS & LOGGERS Power Quality Meter Model A measurement tool for electrical parameters and distribution network disturbances
More informationExercise 2: FACET Base Unit Familiarization
Exercise 2: FACET Base Unit Familiarization EXERCISE OBJECTIVE When you have completed this exercise, you will discover the operating features of the base unit and DC FUNDAMENTALS circuit board. You will
More informationPSM-Mobile User s Manual
7/23/09 PSM-Mobile User s Manual Contents PSM-Mobile User s Manual...1 Introduction...1 Getting Started (Installing / Starting PSM-Mobile)...2 Free 30 Day Trial...3 PSM-Mobile Main Screen...3 PSM-Mobile
More informationEnerSure Installation Guide
EnerSure Installation Guide Danger!!! The electrical components of this system may contain voltage and /or amperage sufficient to injure or kill. Installation is only to be performed by a licensed, bonded
More informationBasic Setup for the Current Probes Input Option
Basic Setup for the Current Probes Input Option The Current Probe Input Option is an ordering option available on 9510 / 9610 meters that allows the use of external current probes. These probes can be
More informationSeries 3000 User Manual and Product Features
Series 3000 User Manual and Product Features PN: OXA3501-890000 Revision 1.0 Technical Specifications 1.1 Model Number Description 1. Meter Series S3 Series 3000 meter Figure 1: Series 3000 model number
More informationCHAPTER 3B: ELECTRONIC POWER STEERING
Electronic Power Steering CHAPTER 3B: ELECTRONIC POWER STEERING NOTE: The basic steering system, such as the tie rod ends, drag links axles, etc., is covered in Chapter 3A: Steering. In 2012, Cub Cadet
More informationModel R5005. Instruction Manual. True RMS Industrial Multimeter. reedinstruments. www. com
Model R5005 True RMS Industrial Multimeter Instruction Manual reedinstruments com Table of Contents Safety... 4 Features... 5 Specifications...5-6 Instrument Description...7-8 Operating Instructions...9-13
More information3 PHASE POWER ANALYZER
SD card real time data recorder with harmonic measurement 3 PHASE POWER ANALYZER Model : DW-6095 Your purchase of this 3 PHASE POWER ANALYZER marks a step forward for you into the field of p r e c i s
More informationDRTS 3 PLUS. Advanced Protection Relay Test Set and Measurement System. DRTS 3 PLUS has been designed to test:
Advanced Protection Relay Test Set and Measurement System Multi-tasking equipment designed for testing protection relays, energy meters, transducers Particularly designed to test RTU (remote terminal unit)
More informationSDM630M CT USER MANUAL 2016 V4.7. DIN Rail Energy Meter for Single and Three Phase Electrical Systems
SDM630M CT DIN Rail Energy Meter for Single and Three Phase Electrical Systems Measures kwh Kvarh, KW, Kvar, KVA, P, F, PF, Hz, dmd, V, A, THD,etc. Bi-directional measurement IMP & EXP Two pulse outputs
More informationWiring Instructions v3
Wiring Instructions v3 Gatekeeper h4.1 Technical Support support@gymmastersoftware.com USA: 415 678 1270 Australia: 03 9111 0323 : 03 974 9169 Copyright 2017 Treshna Enterprises. All rights reserved. Table
More informationSureTest Model ST 1D Instructions
#61-152 #61-153 SureTest Model ST 1D Instructions Introduction The SureTest family of circuit analyzers identify problems common to electrical circuits quickly, easily and accurately. They have a patented
More informationBillion SG3015. Compact ZigBee Power Meter Series. Fully complied with IEEE
T1 T2 T3 Single phase- 2 wire Billion SG3015 T4 Compact ZigBee Power Meter Series The Billion SG3015 series is a cost-effective energy monitoring and management solution deployed in Home Area Networks,
More informationBC-7000 Field Calibration Procedure 55 AMP
BC-7000 Field Calibration Procedure 55 AMP CF1_FIELDCAL_BC7000 Revised 9/8/2012 INTRODUCTION: The BC-7000 Battery Capacity Analyzer will perform capacity testing of 12 and 24 volt lead-acid batteries.
More informationAutomotive Electronics Council Component Technical Committee
ATTACHMENT 3 AEC - Q100-003 REV-E MACHINE MODEL ELECTROSTATIC DISCHARGE TEST Acknowledgment Any document involving a complex technology brings together experience and skills from many sources. The Automotive
More informationDRTS 66 can test all the following relays
Testing all relay technologies: electromechanical, solid state, numerical and IEC61850 Manual control with color display Simultaneously available: 6 Current and 6 Voltage plus 1 battery simulator outputs
More informationProduct description. At a glance. performance in a metal housing coating available Precise autocollimation optics. sensors
-2 Laser Small photoelectric sensors High-performance photoelectric sensor family with laser optics Product description At a glance performance in a metal housing coating available Precise autocollimation
More informationUser's Guide. Model (60Hz) Model (50Hz) 1000A 3-Phase Power Analyzer/Datalogger NO.
User's Guide 1000A 3-Phase Power Analyzer/Datalogger Model 382090 (60Hz) Model 382091 (50Hz) P Q S NO. U12 Y-M U23 D-h U3 m-s 1 2 c I4 3 4 Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument
More informationI n s t a l l a t i o n M a n u a l. T E D P r o. ( T P C O n l y ) A B C. Rev 1.1
I n s t a l l a t i o n M a n u a l f o r T E D P r o ( T P C O n l y ) A B C Page 2 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * I M P O R T A N T The successful installation
More informationModels beginning with 2M, 2L or 2X. Product Description. Technical Specifications. Installation Instructions. Series 2000 Multiple Meter Units (MMUs)
Models beginning with 2M, 2L or 2X Series 2000 Multiple Meter Units (MMUs) Product Description Technical Specifications Installation Instructions February 28 th, 2013 List of Figures...2 List of Tables...2
More informationTHREE-PHASE POWER QUALITY ANALYZER
THREE-PHASE POWER QUALITY ANALYZER PowerPad Model 3945-B Display and record waveforms, transients, trend data and events simultaneously! Display real-time color waveforms measurements at a glance Direct
More informationISSPRO 3 3/8" DIAMETER PROGRAMMABLE SPEEDOMETER Air Core Version
GENERAL INFORMATION: Operating Voltage: Input: Magnetic sensor or AC generator Transient Protection: +100 V, -400 V Reverse Voltage Protected ISSPRO 3 3/8" DIAMETER PROGRAMMABLE SPEEDOMETER Air Core Version
More informationSefram SEFRAM DAS 20/DAS 40. Sefram
Make sure to visit our Website http://www.sefram.fr Sefram Sefram SEFRAM DAS 20/DAS 40 2 to 4 analogue channels Universal input DC, AC+DC RMS voltage measurement Frequency, Thermocouple Power analysis
More informationX/Y Issues on ASP-645-1
X/Y Issues on ASP-645-1 Issues seen with X or Y problems: A) Table will not move in X or Y when you are using the Frame Arrow buttons on the control panel. B) On power up the control panel gives Error
More informationMicrosoft PowerPoint 2007 Beginning
Microsoft PowerPoint 2007 Beginning Educational Technology Center PowerPoint Presentations on the Web... 2 Starting PowerPoint... 2 Opening a Presentation... 2 Microsoft Office Button... 3 Quick Access
More information3-Phase Power Analyzer/Datalogger
User Guide 3-Phase Power Analyzer/Datalogger MODEL PQ3450 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Table of Contents 1.0
More informationInstruction Manual for BE-SP3 Circuit. 10/21/07
Page 1 of 54 Instruction Manual for BE-SP3 Circuit. 10/21/07 Page 1 Index: Page 2 BE-SP3 Circuit Specifications. Page 3-4 Intro to the BE-SP3. Page 5 Basics of serial to parallel. Page 6-7 ASCII Code.
More informationIntroduction REAR VIEW SAFETY
TM 1 What s in the Box? 1 Color Weather Proof Backup Camera 7" Color TFT LCD Digital Clip-on Mirror Monitor 1 3 Channel Multiplexer Control Unit 1 66 Extension Cable for Camera 1 Remote Control 1 Power
More informationIntegrated Metering Systems, Inc.
Integrated Metering Systems, Inc. Models beginning with MS120F and MD240F Mini Meter in Flush Mount Enclosure Product Description Technical Specifications Installation Instructions PN: 114-0003 Revision
More informationTestJet/VTEP Hardware Description and Verification
TestJet/VTEP Hardware Description and Verification Application Note Agilent Technologies Notices Agilent Technologies, Inc. 2008 No part of this document may be reproduced in any form or by any means (including
More informationMultidisciplinary Senior Design
Multidisciplinary Senior Design P10531: Piezoelectric Developer Sensor Standard Operating Procedure 12 May 2010 Dean Culver, Project Manager Thomas Siegwarth, Lead Engineer Thomas Bundy Elizabeth Cormier
More informationOPERATING INSTRUCTIONS:
List OPERATING INSTRUCTIONS: Preparation For Installation, Product Identification Charging The Batteries ing And Adjusting The Lift Mounting Head s Brackets Mounting Clamps And Quick-Locking Arms Installation
More informationBATTERY ANALYSER CALIBRATION PROCEDURES
BATTERY ANALYSER CALIBRATION PROCEDURES Reference Unit: This reference unit is a sample unit used to check the analysed results of the production units when there is a suspicion of tested results accuracy.
More informationInstruction Manual. M Pump Motor Controller. For file reference, please record the following data:
Instruction Manual M Pump Motor Controller For file reference, please record the following data: Model No: Serial No: Installation Date: Installation Location: When ordering replacement parts for your
More informationM A C 3 Wind Speed Alarm & Controller
M A C 3 Wind Speed Alarm & Controller Installation Instructions Thank you for purchasing the MAC3 wind speed alarm and controller. This manual is designed to lead you through a step-by-step process to
More informationMAE106 Laboratory Exercises Lab # 1 - Laboratory tools
MAE106 Laboratory Exercises Lab # 1 - Laboratory tools University of California, Irvine Department of Mechanical and Aerospace Engineering Goals To learn how to use the oscilloscope, function generator,
More informationWE-20. Quick Start Guide For Operating The. Portable Three-Phase Meter Tester/Analyzer
Quick Start Guide For Operating The WE-20 Portable Three-Phase Meter Tester/Analyzer 333 Crosspark Drive Pearl, Mississippi 39208 USA P: 601.933.0900 F: 601.933.0901 E: sales@watthour.com www.watthour.com
More informationEMDX3 Multifunction meter Cat No ModbusTable LGR EN v1.01.xls
GENERAL MODBUS TABLE ORGANIZATION Starting of the Starting of the Group s Group s System Version (Release) System Version (Build) Group Name (Text) Group Code Group Complexity Group Version 36096 8D00
More informationFigure 1. 6-Way JAMMA Switcher
RiddledTV.com 6-Way, Single-Board JAMMA Switcher INSTALLATION GUIDE Figure 1. 6-Way JAMMA Switcher Features: Supports 6 JAMMA boards Only 1 JAMMA board is powered at a time. No external remotes required
More informationINTELLIGENT ENERGY / POWER METER OPERATING GUIDE VERSION 3 MAY, 2013
INTELLIGENT ENERGY / POWER METER OPERATING GUIDE VERSION 3 MAY, 2013 For the EnGenius User Manual, visit www.kele.com/engenius and click on the Related Documents tab. Operating Guide EnGenius Intelling
More information/21 CLAMP ON POWER
Established 98 Advanced Test Equipment Rentals www.atecorp.com 800-404-ATEC (83) INSTRUCTION MANUAL 369-0/ CLAMP ON POWER HiTESTER i Contents Contents Introduction... Standard Accessories and Options...
More information1000A 3-Phase Power Analyzer/Datalogger
User Guide 1000A 3-Phase Power Analyzer/Datalogger Model 382090 (60Hz) Model 382091 (50Hz) Introduction Congratulations on your purchase of the Extech 382090/382091 1000A 3-Phase Power Analyzer Datalogger.
More informationBC-5000 Field Calibration Procedure 55 AMP
BC-5000 Field Calibration Procedure 55 AMP CF1_FIELDCAL Revised 9/8/2012 INTRODUCTION: SCOPE: The BC-5000 Battery Capacity Analyzer will perform automatic capacity testing of 12 and 24 volt lead-acid batteries.
More information99 Washington Street Melrose, MA Fax TestEquipmentDepot.com # # Series Power Analyzer Model 806 Instruction Manual
99 Washington Street Melrose, MA 02176 Fax 781-665-0780 TestEquipmentDepot.com #61-806 #61-807 800 Series Power Analyzer Model 806 Instruction Manual Table of Contents 1. Basic instructions 3 1.1. Introduction.
More informationHarmonicGuard Series Bus-Applied Active Harmonic Filter Quick Start Unit Software Setup
HarmonicGuard Series Bus-Applied Active Harmonic Filter Quick Start Unit Software Setup TCI, LLC W132 N10611 Grant Drive Germantown, Wisconsin 53022 Phone: 414-357-4480 Fax: 414-357-4484 Helpline: 800-TCI-8282
More informationOPERATING GUIDE endicator intelligent energy monitoring
OPERATING GUIDE FOR THE ENDICATOR USER MANUAL, visit www.kele.com/endicator and click on the Related Documents tab. OPERATING GUIDE endicator intelligent energy monitoring The endicator energy monitor
More informationNanoWin. User's Manual - Rel. NW-1.1. Windows 9x and Windows NT 4.0 Data Management Software for NANOVIP Plus and NANOVIP Plus MEM Handheld Analysers
NanoWin User's Manual - Windows 9x and Windows NT 4.0 Data Management Software for NANOVIP Plus and NANOVIP Plus MEM Handheld Analysers Page 1 of 35 NanoWin Windows 9x and Windows NT 4.0 Data Management
More informationUser Guide. 3-Phase Power and Harmonics Analyzer / Datalogger MODEL PQ3470
User Guide 3-Phase Power and Harmonics Analyzer / Datalogger MODEL PQ3470 Table of Contents 1.0 INTRODUCTION 1-1 Features... 3 1-2 Safety... 4 2.0 SPECIFICATIONS 2-1 General Specifications... 5 2-2 Electrical
More informationDEFAULT SCREEN. Button and Screen Layout DRILLING WIDTH TARGET RATE HOPPER NUMBER CROP NAME DRILLING ACTION CROP NUMBER. HOPPER selection POWER On/Off
DEFAULT SCREEN Button and Screen Layout DRILLING WIDTH TARGET RATE CROP NAME HOPPER NUMBER DRILLING ACTION CROP NUMBER HOPPER selection POWER On/Off AREA / DISTANCE TARGET RATE Increase CROP Scroll / Up
More informationGSV-3USBx2 3,5mV/V 4,2V
x2 3,5mV/V 4,2V Highlights Powered via USB port Sampling rate 10 khz Data rate 1...1000 Hz straingage quarter, half, full bridges Built-in bridge supplement 350 Ohm Optionally also for displacement transducers
More informationUsing PSpice to Simulate Transmission Lines K. A. Connor Summer 2000 Fields and Waves I
Using PSpice to Simulate Transmission Lines K. A. Connor Summer 2000 Fields and Waves I We want to produce the image shown above as a screen capture or below as the schematic of this circuit. R1 V1 25
More informationWELDTRON PIPELINER Troubleshooting problems with the Pipeliner Remote Amp Control.
WELDTRON PIPELINER Troubleshooting problems with the Pipeliner Remote Amp Control. In the event that your Pipeliner remote control does not operate correctly, use the troubleshooting procedures below to
More informationEnercept H8035/H8036 Modbus Energy Meter Networked kw/kwh Transducers
POWER MONITORING INSTALLATION GUIDE Enercept H8035/H8036 Modbus Energy Meter Networked kw/kwh Transducers US Patent No. 6,373,238 Installer's Specifications Input Voltage 208 to 480 VAC Number of Phases
More informationContents Safety Requirements... 1 Safety Instructions... 1 Safety Sign... 2 General Description... 2 Features... 2 Appearance...
Contents Safety Requirements... 1 Safety Instructions... 1 Safety Sign... 2 General Description... 2 Features... 2 Appearance... 3 Knob Switch perations... 4 Button Switch perations... 5 LCD Display...
More informationSDG1400 User s Guide
SDG1400 User s Guide Model SDG1400 Rate Sensor Systron Donner Inertial Sales and Customer Service Phone: +1 925.979. 4500 Fax: +1 925.349.1366 E-Mail: sales@systron.com www.systron.com SDG1400 User s Guide
More informationMG586 Calibration and Maintenance
MG586 Calibration and Maintenance The Best Tool The Small Crane Operator Ever Had! Set Up and Calibration of the Greer MicroGuard 586 Computer System A Little History Review Predecessor- the MG-585 Display
More informationmidi LOGGER 900 SERVICE MANUAL GL900-UM-251 GL900-UM
midi LOGGER 900 GL900-UM-251 SERVICE MANUAL GL900-UM-251-01-9370 HISTORY OF REVISIONS No. Date issued Description of revision Page Edition 1 08.07.26 First Printing All 01 GL900-UM-251-9370 i TO ENSURE
More informationIntroduction. Chapter 2
The Vantage PRO unit (Figure 2-1) combines a digital and graphing multimeter, lab scope and ignition scope with a powerful diagnostic database. Figure 2-1 Vantage PRO This diagnostic database gives you
More informationLIVE C.T. ADMITTANCE TESTER 505B DATASHEET REDPHASE INSTRUMENTS
LIVE C.T. ADMITTANCE TESTER 505B DATASHEET REDPHASE INSTRUMENTS Contents Section Key Features Application... 1 Where it is used... 1.1 Admittance Measurement... 1.2 Burden Measurement... 1.3 Hardware features...
More informationWhat s in the Box? REAR VIEW SAFETY
TM 1 What s in the Box? 1 Full HD Color Infra-red Weather Proof Camera 1 Full HD 7" TFT LCD Color Monitor w/monitor Mount 1 Power Harness 1 66 Camera Cable 1 Power Connection Wire 1 Screw Kit for installation
More informationTHE NEW GENERATION OF ADVANCED TEST EQUIPMENTS FOR RELAYS, ENERGY METERS, TRANSDUCERS AND POWER QUALITY METERS.
D R T S 6 6 THE NEW GENERATION OF ADVANCED TEST EQUIPMENTS FOR RELAYS, ENERGY METERS, TRANSDUCERS AND POWER QUALITY METERS. www.isatest.com DRTS 66 The new generation of advanced test equipments for relays,
More informationModels beginning with BL, S1, S2, 2N, or 2R Individual Meters. Product Guide Technical Specifications Installation Instructions
Models beginning with BL, S1, S2, 2N, or 2R Individual Meters Product Guide Technical Specifications Installation Instructions PN: 114-0004 Revision 1.1 List of Figures...2 List of Tables...2 1. Product
More information