MODEL: IT40SW2. Tower Light Series. [2] LAMP 1 COLOR (1st layer from the top) R: Red Y: Amber G: Green B: Blue W: White

Transcription

1 MODEL: IT0SW Tower Light Series WIRELESS LAN TOWER LIGHT (small size, 0 mm dia., Modbus/TCP, access point, - layers) Functions & Features Lighting, blinking and buzzing available with contact input or PC via Modbus/TCP. status acquisition available through wireless LAN. Connection to network with bridge function, in remote I/O Ethernet type via wireless LAN. LAN access point complied with IEEE80.b/g/n Nondirectional antenna (60 horizontal) Client use is available by mode change. Conforming to Electronic Communications Act, 00 of the Republic of South Africa 88 (.7) A [] LAMP COLOR (st layer from the top) [] LAMP COLOR (nd layer from the top) N: None (not available when Lamp Layers selected are - ) [] LAMP COLOR (rd layer from the top) N: None (not available when Lamp Layers selected are - ) mm (inch.) Lamp Layers 60 (.6) A (8.8) 6 (0.08) 88 (.) 0 (.60) (.86) MODEL: IT0SW-[][][][][][6]D-R[7] ORDERING INFORMATION Code number: IT0SW-[][][][][][6]D-R[7] Specify a code from below for each [] through [7]. (e.g. IT0SW-RYGBWD-R/ZA) [] LAMP LAYERS : layer : layers : layers : layers : layers [] LAMP COLOR (th layer from the top) N: None (not available when Lamp Layers selected are - ) [6] LAMP COLOR N: None (not available when Lamp Layers selected are ) * The selection of the same color for more than one layer is not available. * Select "None" option for the layers other than the selected. MOUNTING D: Direct mounting IT0SW SPECIFICATIONS ES-86 Rev.8 Page /6

2 MODEL: IT0SW DESIGN TYPE : Type (refer to outline dimensions) POWER INPUT DC Power R: V DC (Operational voltage range V ±0 %, ripple 0 %p-p max.) [7] COUNTRY blank: Japan, EU /ZA: South African Republic RELATED PRODUCTS LAN cable (model: ITCA) Mounting Pole (model: ITPL) PC configurator software (model: ITCFG) Functions are configurable using the PC Configurator Software. Downloadable at M-System s web site. GENERAL SPECIFICATIONS Degree of protection: IP 6, vertical mounting only (bottom connectors excluded) Connection Power: UL007 AWG0 Input: UL007 AWG Ethernet: RJ- Modular Jack Housing material: Flame-resistant resin Lens: Flame-resistant resin (transparent) Isolation: Discrete input or power input to network DIP SW Setting: Frequency of lamp blinking and buzzing discontinuance, buzzing volume level, output at connection failed and IP address (refer to the instruction manual) Lamp: Red, amber, green, blue and white LEDs on/blinking (approx. Hz, 0 Hz) Indicator LEDs: Power, Run (Refer to the insruction manual) Buzzing: Approx.. khz Interval: continuous/intermittent (approx. Hz, 0 Hz) COMMUNICATION Common spec. Modbus protocol Protocol: Modbus/TCP Data: RTU (Binary) Port No.: 0 Max. number of socket connections: 0 DHCP protocl: DHCP server IP address: (factory setting); Selectable with PC Configurator Software (model: ITCFG) Ethernet Communication Standard: IEEE 80.u Transmission: 0BASE-T, 00BASE-TX Baud rate: 0/00 Mbps (Auto Negotiation function) Transmission media: 0BASE-T (STP, Category ) 00BASE- TX (STP, Category e) Max. length of fieldbus segment: 00 meters IP address: (factory setting); Selectable with PC Configurator Software Ethernet indicator LED: Link, Link00, COL LAN Communication Standard: IEEE 80.b/g/n Frequency range: MHz (ch - ch) Max. transmision distance (optical): Approx. 0m (depends on setting) Access mode: infrastructure Security: WEP 6bit/8bit, WPA (TKIP, AES), WPA (TKIP, AES) LAN indicator: WLAN Number of clients: INPUT SPECIFICATIONS Discrete Input: Dry contact, open collector NPN Input resistance: Approx.. kω Common: Negative common NPN ON level: V /. ma (Input - COM) OFF level: 8 V DC / ma (Input - COM) Input current:. ma per V DC INSTALLATION Power consumption DC: Approx.. W Operating temperature: -0 to + C ( to F) Operating humidity: 0 to 8 %RH (non-condensing) Atmosphere: No corrosive gas Mounting: Direct mounting Mounting direction: Vertical Weight: Approx. 60 g (. lb) PERFORMANCE Insulation resistance: 00 MΩ with 00 V DC Dielectric strength: 00 V minute (discrete input or power to network IT0SW SPECIFICATIONS ES-86 Rev.8 Page /6

3 MODEL: IT0SW STANDARDS & APPROVALS Built-in module certified under Japanese Radio Law EU conformity: RE Directive EN 00 8 V.. RoHS Directive EN 08 EN V.9. EN Certified under Electronic Communications Act, 00 of ICASA (Independent Communications Authority of South Africa) EXTERNAL VIEW FRONT VIEW (with the cover open) BOTTOM VIEW Lamp Lamp Lamp Power Link COL WLAN Run Link00 WLAN FRONT Lamp Mode Ethernet Modular Jack Status Indicator LED Power Link COLWLAN Run Link00WLAN DIP SW Antenna IP Address Reset Buzzer Aperture Gasket IT0SW SPECIFICATIONS ES-86 Rev.8 Page /6

4 MODEL: IT0SW DIMENSIONS unit: mm 0±.dia. A± Control Panel Cover R77. 6 lengths* (8) Lamp Layers A Bolts and Nuts (M) (8) Approx.00 ±. dia. Lead wires (0 dia.) *. Consult M-System for other bolt length. MOUNTING REQUIREMENTS unit: mm Wiring Hole 0 dia.* dia. Holes ( dia.) 0 Front *Protect wires to prevent scratching them at the edge of the compartment. IT0SW SPECIFICATIONS ES-86 Rev.8 Page /6

5 MODEL: IT0SW SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Antenna Connector Comm. LAMP BUZZER To other Ethernet devices LAMP INPUT Red RJ- JACK LAMP * Isolation Comm. STAUS IND. LED DIP SW LAMP INPUT LAMP INPUT LAMP INPUT Yellow Green Blue LAMP * LAMP * LAMP * Control IP ADDR. RESET SW INPUT LAMP INPUT White LAMP * Input BUZZER INPUT Continuance Purple BUZZER BUZZER INPUT Discontinuance Cyan BUZZER LAMP COM Brown POWER Gray Black + /COM Power *. Example of layers in order: red, yellow, green, blue and white. Lamp and wire color are the same. WIRING TO INPUT SIGNAL e.g. NPN input e.g. ON TOWER LIGHT LAMP LAMP ON TOWER LIGHT LAMP LAMP LAMP LAMP LAMP LAMP LAMP LAMP BUZZER BUZZER BUZZER BUZZER + + /COM /COM Note : If On (Continuous) and Blink (Intermittent) are set simultaneously for a single lamp (buzzer), Blink (Intermittent) is disabled. The same procedure will be applyed also for the others lamps. IT0SW SPECIFICATIONS ES-86 Rev.8 Page /6

6 MODEL: IT0SW SYSTEM CONFIGURATION EXAMPLES EXAMPLE. Activate the tower light lamp and buzzer with contact input.. Aquire data of contact status of tower light lamp with PC. IT0SW Communication IT0SW ITxSW PC IT60SW EXAMPLE. Activate the tower light lamp and buzzer with PC. Communication IT0SW PC ITxSW Communication EXAMPLE. Activate the tower light lamp and buzzer with PC.. Interchange data between PC and Remote I/O. IT0SW PC Comm. ITxSW IT60SW Remote I/O Contact status of tower light described on example is also available while interchanging data with PC. Client is available with ITxSW. Specifications are subject to change without notice. IT0SW SPECIFICATIONS ES-86 Rev.8 Page 6/6