Constructing a Geometric Attribute Workflow
|
|
|
- Brooke Reynolds
- 5 years ago
- Views:
Transcription
1 Constructing a Geometric Attribute Workflow. Introduction Attribute computation of very large data volumes can take considerable time. Experienced interpreters may already have familiarity with other data volumes from the same basin. Alternatively, they may have already analyzed a subset of the data using the interactive steps described above. In this situation it may be useful to set up a workflow that will run a suite of attribute programs in the background, perhaps overnight. The workflow here is one of two currently provided. Unlike a mature 3D seismic processing system like ProMax, Seisup, or Focus, the linking and interchangeability is rigidly fixed. After sponsor feedback, we can either improve the workflow described below, or develop an alternative strategy Geometrical attribute Workflow The AASPI Geometrical Attribute Workflow GUI can be invoked from the main aaspi_util as shown above or by typing in aaspi_geom_attr_workflow separately in the terminal window. The following workflow GUI will then pop up. Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 1
2 Step 1: Save the workflow environment parameters In step 1 we need to input the seismic amplitude file and set up the project name and the MPI parameters which will be used for all the MPI processes. The seismic amplitude file is selected first (Arrow 1). Enter the project name and the suffix (Arrow 2). Verbose can be selected if required (Arrow 3). It is recommended to use MPI because except euler_curvature all the other processes run on MPIs (Arrow 4). Mention the processors per nodes and the node list. Each of our machines tripolite.ou.edu and hematite.ou.edu have 12 processors in it. Thus in the processors per node 12 is mentioned (Arrow 5) and in the node list tripolite and hematite is mentioned (Arrow 6). After entering out all the parameters these parameters are saved (Green Arrow) which will be subsequently used for all the processes. Note that initially all the attribute buttons will be disabled. When the Save Environment parameters is clicked the dip3d and the spec_cmp buttons will be highlighted as shown. These two takes in only the seismic amplitude as inputs Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 2
3 and are thus activated. The subsequent attribute buttons will be activated after their input file criterions are met. Step 2: Save the parameters for the volumetric attributes In this step each of the attribute program is opened and their parameters are saved. The buttons are activated only when their input criterion are met. For example the imagefilt3d gets activated only after we open and save the dip3d parameters. The next figure shows the GUIs for dip3d and imagefilt3d. The parameters are mentioned and the Save and Exit button (green arrow) is pressed. Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 3
4 Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 4
5 Note that after saving the imagefilt3d parameters the similarity3d, curvature3d and the glcm3d buttons are activated since all these three require the inline and crossline dip volumes as an input. Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 5
6 The GUI for similarity3d; the output from the imagefilt3d will be input to this program. Enter the proper parameters and then save and exit (green arrow). The parameter file get saved automatically as a similarity3d.parms file The GUI for sof3d; the output from the imagefilt3d and the similarity3d will be input to this program. Enter the proper parameters and then save and exit (green arrow). The parameter file get saved automatically as a sof3d.parms file Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 6
7 Note that with the saving the sof3d and the re-run similarity3d is activated. The re-run similarity calculates again the energy-ratio, Sobel-filter attributes taking in the PC or LUM filtered seismic dataset (output from the sof3d program). Thus it is sometimes better to re-run the similarity3d attributes so that the attributes are created on the filtered volume. Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 7
8 The GUI for curvature3d; the output from the imagefilt3d will be input to this program. Enter the proper parameters and then save and exit (green arrow). The parameter file get saved automatically as a curvature3d.parms file. Note: Only one of the curvature programs (either structural or amplitude curvature) can be executed for at one time. By default, the structural curvature GUI will pop up. To run the attributes for the amplitude curvature, it can be done separately or one can toggle the button (highlighted in blue) to change into amplitude curvature. Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 8
9 The GUI for euler_curvature; the output from the curvature3d will be input to this program thus the button for euler_curvature gets activated only after saving the curvature3d parameters. Enter the proper parameters and then save and exit (green arrow). The parameter file get saved automatically as a euler_curvature.parms file. Note: By default, the structural Euler curvature GUI will pop up. To run the attributes for the amplitude Euler curvature, it can be done separately or one can go to the next tab to change into amplitude Euler curvature. Also remember that if the parameters for structural curvature in saved for the curvature3d program the parameters for structural Euler curvature should be saved and vice-vesa. Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 9
10 Step 3: Execute the geometric attribute workflow Above shows the GUI for one of the typical workflows. To execute the workflow press the Execute Geometrical Attribute Workflow (green arrow). The reset selection button (orange arrow) can be pressed if one wants to reset the program selections. A typical workflow for structural geometrical attributes will be dip3d>imagefilt3d>similarity3d>sof3d>rerun-similarity3d>k_curvature3d>k_euler_curvature> A typical workflow for amplitude geometrical attributes will be dip3d>imagefilt3d>similarity3d>sof3d>rerunsimilarity3d>e_curvature3d>e_euler_curvature>glcm3d>spec_cmp Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 10
11 The above shows the terminal window after saving all the *.parms (parameter) files. The aaspi_env.parms is a text file with the information of the input seismic file, the project and the suffix names and the MPI settings. We can do cat aaspi_env.parms to see the file contents. The other *.parms contents the saved parameters from all saved programs. At any time, the terminal window will show the progress of the workflow. The text file aaspi_geom_attr_workflow.out can be checked to see the completion status of the workflow or whether there is any error in the execution of the program. Attribute-Assisted Seismic Processing and Interpretation - 18 December 2015 Page 11
Prestack Workflows: Prestack Structure-Oriented Filtering. The Prestack Structure-Oriented Filtering Workflow. Introduction
The Prestack Structure-Oriented Filtering Workflow. Introduction Structure-Oriented Filtering (SOF) involve many programs in AASPI software. Particularly, prestack SOF is tedious and time-consuming. To
Iterative Fault Enhancement Workflow
Iterative Fault Enhancement Workflow. Introduction A greater degree of filtering can be obtained using three methods: (1) applying more aggressive filter parameters using the original window, (2) applying
AASPI SOFTWARE PARALLELIZATION
AASPI SOFTWARE PARALLELIZATION Introduction Generation of multitrace and multispectral seismic attributes can be computationally intensive. For example, each input seismic trace may generate 50 or more
PRESTACK STRUCTURE-ORIENTED FILTERING PROGRAM sof_prestack
PRESTAK STRUTURE-ORIENTED FILTERING PROGRAM sof_prestack omputation Flow hart Program sof_prestack is a generalization of program sof3d For this reason, the input parameters and workflow of the two algorithms
Well Log Utilities: Program LAS file importer
Overview The well log modules in AASPI allow you to: import LAS format *.las files and convert them to *.H AASPI format, display the curves, and export AASPI-format *.H files as LAS-format *.las files.
COMPUTING APPARENT DIP AND AMPLITUDE GRADIENTS PROGRAM apparent_cmpt. Apparent curvature computation flow charts
COMPUTING APPARENT DIP AND AMPLITUDE GRADIENTS PROGRAM apparent_cmpt Apparent curvature computation flow charts inline dip crossline dip apparent_cmpt p(φ=-90 0 ) p(φ=0 0 ) p(φ=+30 0 ) p(φ=-60 0 ) p(φ=+60
2D Seismic Utilities Programs: aaspi_segy_read_batch aaspi_2d_combine aaspi_pseudo3d_split aaspi_mega2d_split aaspi_segy_write_batch
2D Seismic Utilities Programs: aaspi_segy_read_batch aaspi_2d_combine aaspi_pseudo3d_split aaspi_mega2d_split aaspi_segy_write_batch Most of AASPI utilities, such as dip3d, spec_cwt, and som3d, are designed
Software Installation: AASPI Windows Installation
AASPI Windows Installation This guide shows a step-by-step installation, running, and uninstallation of AASPI software on Windows machine. Compatibility Currently we support 64-bit Windows XP, 7, 8, 8.1,
(1B) Click Browse and select the AASPI-format file (*.H) that you want to display. After you browse the file, the Colorbar file name (1C), plot title
QC PLOTTING OF AASPI-FORMAT DATA AND ATTRIBUTES Program aaspi_plot The AASPI QC Plotting tab To further quality control the conversion process, you will wish to plot your data before computing seismic
FLATTENING AND GENERATING STRATAL SLICES PROGRAMS flatten, vector_flatten, stratal_slice, and vector_stratal_slice
FLATTENING AND GENERATING STRATAL SLICES PROGRAMS flatten, vector_flatten, stratal_slice, and vector_stratal_slice Extracting phantom horizon and stratal slices is one of the more common interpretation
STRUCTURE-ORIENTED FILTERING OF POSTSTACK DATA Program sof3d
STRUCTURE-ORIENTED FILTERING OF POSTSTACK DATA Program sof3d Computation flow chart Program sof3d provides the application and blending of anisotropic diffusion filtering described by Fehmers and Höecker
Improving Dip Estimates Program filter_dip_components
Improving Dip Estimates Program filter_dip_components Computation flow chart The input to program filter_dip_components is generally computed from program dip3d and includes estimates of the inline and
MULTIATTRIBUTE DISPLAY: PROGRAMS hlplot, hsplot, hlsplot, rgbplot, and crossplot
MULTIATTRIBUTE DISPLAY: PROGRAMS hlplot, hsplot, hlsplot, rgbplot, and crossplot Multiattribute display of dip magnitude modulating dip azimuth Programs hlplot and hsplot In section 6, pages 12-13, we
MODULATING A POLYCHROMATIC IMAGE BY ONE PLOTTED AGAINST LIGHTNESS: PROGRAM hlplot
MODULATING A POLYCHROMATIC IMAGE BY ONE PLOTTED AGAINST LIGHTNESS: PROGRAM hlplot Multiattribute display of dip magnitude modulating dip azimuth Program hlplot AASPI provides two ways to blend a polychromatic
Enhancing faults and axial planes Program fault_enhancement
Enhancing faults and axial planes Program fault_enhancement Overview The fault enhancement attribute is a post-stack attribute which enhances locally planar features within a seismic attribute volume.
COMPUTING APPARENT CURVATURE PROGRAM euler_curvature. Euler curvature computation flow chart. Computing Euler curvature
COMPUTING APPARENT CURVATURE PROGRAM euler_curvature Euler curvature computation flow chart Inline dip Crossline dip curvature3d k 1 Strike of k 1 k 2 Strike of k 1 euler_curvature (φ=-90 0 ) (φ=0 0 )
Spectral Attributes Program spec_cmp. COMPUTING SPECTRAL COMPONENTS USING A COMPLEX MATCHING PURSUITE ALGORITHM PROGRAM spec_cmp
COMPUTING SPECTRAL COMPONENTS USING A COMPLEX MATCHING PURSUITE ALGORITHM PROGRAM spec_cmp Alternative Spectral Decomposition Algorithms Spectral decomposition methods can be divided into three classes:
Computation flow chart
COMPUTING SIMILARITY ATTRIBUTES PROGRAM similarity3d Computation flow chart The input to program similarity3d includes inline and crossline components of reflector dip and a seismic amplitude volume. The
Petrel TIPS&TRICKS from SCM
E&P SOLUTIONS Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Cropped & Flattened Volumes in *Petrel Geophysicists who use D volumes often want to work on a smaller part of the volume or they want
Program flatten reads in an input seismic or attribute volume as well as a picked horizon and generates a flattened output volume:
FLATTENING A SCALAR DATA VOLUME PROGRAM flatten Computation Flow Chart Program flatten reads in an input seismic or attribute volume as well as a picked horizon and generates a flattened output volume:
Random Forest Classification and Attribute Selection Program rfc3d
Random Forest Classification and Attribute Selection Program rfc3d Overview Random Forest (RF) is a supervised classification algorithm using multiple decision trees. Program rfc3d uses training data generated
Seismic imaging PROGRAM aaspi_azim_offset_mig
Seismic imaging PROGRAM aaspi_azim_offset_mig Program aaspi_azim_offset_mig is a prestack time migration based on the Kirchhoff algorithm which adds the anti_aliasing operator based on Gray, S. H. (1992).
MAXIMUM ENTROPY SPECTRAL ANALYSIS PROGRAM spec_max_entropy
MAXIMUM ENTROPY SPECTRAL ANALYSIS PROGRAM spec_max_entropy Alternative Spectral Decomposition Algorithms Spectral decomposition methods can be divided into three classes: those that use quadratic forms,
Displaying on-the-fly crossplot volumes in View3D
Displaying on-the-fly fly crossplot volumes in View3D SAMPLE IMAGE Simon Voisey Hampson-Russell London September 08 Introduction Before the release we needed to export crossplot volumes to SEG-Y for viewing
MODULATING A POLYCHROMATIC IMAGE BY A 2 ND IMAGE PLOTTED AGAINST SATURATION AND A 3 RD IMAGE PLOTTED AGAINST LIGHTNESS: PROGRAM hlsplot
MODULATING A POLYCHROMATIC IMAGE BY A 2 ND IMAGE PLOTTED AGAINST SATURATION AND A 3 RD IMAGE PLOTTED AGAINST LIGHTNESS: PROGRAM hlsplot Plotting dip vs. azimuth vs. coherence Program hlsplot Earlier, we
AASPI Software Structure
AASPI Software Structure Introduction The AASPI software comprises a rich collection of seismic attribute generation, data conditioning, and multiattribute machine-learning analysis tools constructed by
Interactive Velocity Analysis (aaspi_iva): Program: Precompute Velocity Semblance, Interactive Velocity Analysis, Velocity Interpolation
Interactive Velocity Analysis (aaspi_iva): Program: Precompute Velocity Semblance, Interactive Velocity Analysis, Velocity Interpolation Computational Flowchart Time Migrated Prestack Gathers Post Stack
Installing AASPI Software on Linux
Installing AASPI Software on Linux (3-25-2014) Software Location Kurt J. Marfurt (kmarfurt@ou.edu) The current version of the AASPI software will be under a website called geology.ou.edu/aaspi/software.
Volumetric Classification: Program pca3d
Volumetric principle component analysis for 3D SEISMIC FACIES ANALYSIS PROGRAM pca3d Overview Principal component analysis (PCA) is widely used to reduce the redundancy and excess dimensionality of the
Volumetric Attributes: Constrained least-squares spectral analysis Program spec_clssa
CONSTRAINED LEAST-SQUARES SPECTRAL ANALYSIS PROGRAM spec_clssa Alternative Spectral Decomposition Algorithms Spectral decomposition methods can be divided into three classes: those that use quadratic forms,
Correlating Production or Injection Volumes to Volumetric Attributes Program cigar_probe. Computation flow chart
Correlating Production or Injection Volumes to Volumetric Attributes Program cigar_probe Computation flow chart Program cigar_probe uses a suite of seismic amplitude volumes and a table containing the
Attribute Expression of the Mississippi Lime. Attribute expression of the Mississippi Lime
Attribute Expression of the Mississippi Lime Kurt J. (The University of Oklahoma) Attribute expression of the Mississippi Lime Lithology Fractures o Strain o Thickness o Lithology Diagenesis Impedance
Once you have been assigned the role of Search Committee you will receive a system triggered to alert you.
ROCS GUIDE TO SEARCH COMMITTEE ROLE I. THE ROLE OF SEARCH COMMITTEE IN ROCS In ROCS the Search Committee role is assigned to individuals who will review the applicant pool to a job posting they have been
Volumetric Attributes- program curvature3d
COMPUTING REFLECTOR CURVATURE, ROTATION, AND CONVERGENCE - PROGRAM curvature3d Program curvature3d has two modes computing second derivatives of the phase of seismic waveforms (1 st derivatives of structural
dip3d Computing Structural Dip Program dip3d Computation flow chart Volumetric Attributes: Program dip3d
Comuting Structural Di Program di3d Comutation flow chart Program di3d uses a seismic amlitude volume as its inut and generates estimates of inline di, crossline di, di magnitude, di azimuth, and a confidence
Data Loading in CE8 SAMPLE IMAGE. Simon Voisey June 2008 Hampson-Russell London Written for CE8R1
Data Loading in CE8 SAMPLE IMAGE Simon Voisey June 2008 Hampson-Russell London Written for CE8R1 Introduction Data loading has been made much easier in CE8. The principles and locations of the buttons
Which curvature is right for you? Part - 1
Which curvature is right for you? Part - 1 Satinder Chopra*, Arcis Seismic Solutions, Calgary, Alberta, Canada schopra@arcis.com and Kurt J. Marfurt, The University of Oklahoma, Norman, Oklahoma, US. Summary
Using the Log Viewer. Accessing the Log Viewer Window CHAPTER
CHAPTER 6 Users with log permissions can view or delete messages generated by the various servers that make up CCNSC Subscriber Provisioning software. You can display all messages currently in the log
Software Installation - Accessing Linux and Checking your Environmental Variables
Accessing Linux and Checking your Environmental Although you may be fortunate enough to have a powerful multi-processor desktop running Linux, most of our sponsors do not. Most of our sponsors will have
Background on Kingdom Suite for the Imperial Barrel Competition 3D Horizon/Fault Interpretation Parts 1 & 2 - Fault Interpretation and Correlation
Background on Kingdom Suite for the Imperial Barrel Competition 3D Horizon/Fault Interpretation Parts 1 & 2 - Fault Interpretation and Correlation Wilson (2010) 1 Fault/Horizon Interpretation Using Seismic
CITRIX NAVIGATION & ACCESSING myhr
INTRODUCTION This guide details how to log into Citrix and navigate to the myhr Home page. If you have any difficulty throughout this process please contact ICT (extension 43000). After 20 minutes of inactivity,
Petrel TIPS&TRICKS from SCM
E&P SOLUTIONS Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Petrel Inspector The Petrel Inspector was introduced in Petrel 2012 and was augmented with new features in Petrel 2013. It contains a variety
3D Horizon/Fault Interpretation Exercise Using Seismic Micro-Technology s PC based 2d/3dPAK Seismic Interpretation Software
3D Horizon/Fault Interpretation Exercise Using Seismic Micro-Technology s PC based 2d/3dPAK Seismic Interpretation Software Prepared by Tom Wilson, Appalachian Region Resource Center, Petroleum Technology
INTViewer Tutorial Cube Tutorial
INTViewer Tutorial Cube Tutorial This tutorial shows how to use INTViewer to display a seismic cube stored in a Seismic file. Windows created will include INLINE, XLINE, Time Slice and an arbitrary traverse,
Sign in to Create a new account or use an existing one (e.g. from your English class)
Turnitin: Thesis Upload Students Manual General Information The plagiarism check is a mandatory part of your final examination and needs to be done before handing in the thesis. The check generates a report
Adding an Open HMIS Release of Information (ROI) (updated 4/26/18)
1 Adding an Open HMIS Release of Information (ROI) (updated 4/26/18) IF A CLIENT HAS REQUESTED RESTRICTIONS ON THE SHARING OF HIS/HER DATA (SEE ROI, PAGE FIVE) STOP. DO NOT ENTER ANY CLIENT DATA INTO HMIS.
End-of-Year Serials. Steps to Removing Issues at the End of the Year
Steps to Removing Issues at the End of the Year End-of-Year Serials Questions to ask yourself: 1) Did this transfer over from Dynix or did I catalog it like a book in SIRSI? Go to Section A. 2) If I checked
Pre-Stack Seismic Data Analysis with 3D Visualization A Case Study*
Pre-Stack Seismic Data Analysis with 3D Visualization A Case Study* Yongyi Li 1, Josh Feng 1, and Maggie Jiao 1 Search and Discovery Article #41546 (2015)** Posted February 16, 2015 *Adapted from extended
5 Setting Preferences 15 Preferences 15 Configure Chart Colors 16
CRITERION Vantage 3 Acquire Training Manual Contents 1 Introduction 3 Collecting Data 3 2 Starting the Program 3 Logging In and Logging Out 3 Logging In 3 Logging in as an Administrator 3 Logging in as
SIVIC GUI Overview. SIVIC GUI Layout Overview
SIVIC GUI Overview SIVIC GUI Layout Overview At the top of the SIVIC GUI is a row of buttons called the Toolbar. It is a quick interface for loading datasets, controlling how the mouse manipulates the
Downloaded 10/29/15 to Redistribution subject to SEG license or copyright; see Terms of Use at
Pitfalls in seismic processing: part 1 groundroll sourced acquisition footprint Sumit Verma*, Marcus P. Cahoj, Tengfei Lin, Fangyu Li, Bryce Hutchinson and Kurt J. Marfurt, the University of Oklahoma Summary
Emerge Workflow CE8 SAMPLE IMAGE. Simon Voisey July 2008
Emerge Workflow SAMPLE IMAGE CE8 Simon Voisey July 2008 Introduction The document provides a step-by-step guide for producing Emerge predicted petrophysical volumes based on log data of the same type.
1. Enter your User ID or Address associated with your Chalk & Wire account.
Once you have been provided with your Chalk & Wire User ID and Password, go to the Chalk & Wire login web page for your institution. If you do not know the correct URL, please visit ep.chalkandwire.com
Mapping the Subsurface in 3-D Using Seisworks Part 1 - Structure Mapping
Mapping the Subsurface in 3-D Using Seisworks Part 1 - Structure Mapping The purpose of this exercise is to introduce you to the art of mapping geologic surfaces from 3-D seismic data using Seisworks.
Using Kingdom Suite for 3D Horizon/Fault Interpretation Parts 3 & 4 - Horizon Interpretation and Correlation
Using Kingdom Suite for 3D Horizon/Fault Interpretation Parts 3 & 4 - Horizon Interpretation and Correlation Wilson (2010) 1 A footnote to last week's exercise Double Vision? - Last week when you were
P. Bilsby (WesternGeco), D.F. Halliday* (Schlumberger Cambridge Research) & L.R. West (WesternGeco)
I040 Case Study - Residual Scattered Noise Attenuation for 3D Land Seismic Data P. Bilsby (WesternGeco), D.F. Halliday* (Schlumberger Cambridge Research) & L.R. West (WesternGeco) SUMMARY We show that
Loupedeck. Capture One Beta User Guide.
Loupedeck Capture One Beta User Guide What does Capture One Beta Integration actually mean? Currently Loupedeck+ works using keyboard shortcuts where all our other integrations work via the internal support
Creating and using a Turnitin marking rubric
Creating and using a Turnitin marking rubric Turnitin s GradeMark system contains several tools and types of marking that tutors can use when providing feedback. These include: general comments inline
Unit 4 Agresso 571 Web Services. Journal Registration
Unit 4 Agresso 571 Web Services Journal Registration Author S J Price June 2018 CONTENTS Starting Agresso Web... 3 Login Screen... 3 Journal Registration... 4 Registered Journals enquiry... 9 Journal Registration
Volumetric Attributes: Computing Texture Attributes Program glcm3d
GENERATING TEXTURE ATTRIBUTES - PROGRAM glcm3d Computation flow chart The AASPI gray-level co-occurrence matrices and textures attributes are computed along structural dip. In addition to supplying the
Learning how to use Lexis Red
Learning how to use Lexis Red This guide takes you through how to use Lexis Red, the innovative new way of accessing looseleaf content from LexisNexis. If you still need assistance after reading this guide
Evoq 8 Content Managers Training Manual
Evoq 8 Content Managers Training Manual Table of Contents Chapter 1: User Login... 2 User Login...2 User Login Screen...2 User Logout...2 Chapter 2: Navigating within Evoq 8...3 Editing Bar...3 Dashboard...4
Pecos Users' Guide for ProMAX/SeisSpace
Pecos Users' Guide for ProMAX/SeisSpace 1 Installation You must be running SeisSpace version 5000.8.5.0 or above to use Pecos in SeisSpace. Download and extract the prowess_xtgeo.tar.gz folder into the
Frequently Asked Questions
Frequently Asked Questions Employee Self-Service Easy Reference 1. Why didn t I receive the email from The Ahola Corporation (ahola@myisolved.com)? p.2 2. When I click the link in the registration email,
Quick Reference Card Effort Planning System (EPS) Faculty DOE Review & Processing
Process: This Quick Reference Card (QRC) contains brief, direct instructions for faculty members to access, review and process their DOEs in the UK Effort Planning System (EPS). More detailed information
Accuterm 7 Usage Guide
P a g e 1 Accuterm 7 Usage Guide Most if not all computers on our campus have Accuterm 7 already installed on them. To log in, you will double click the icon on your desktop that looks like the one shown
HRS-9 Data Slice Editing and Math. Jon Brown 2013
HRS-9 Data Slice Editing and Math Jon Brown 2013 Overview HRS-9 has several tools for editing, combining, or processing horizons and data slices. This document includes: Automated Math processes. An example
Word 2010 Getting Started with Word. Introduction. Getting to know Word The Ribbon. Video: Exploring Your Word 2010 Environment
Word 2010 Getting Started with Word Introduction Word 2010 is a word processor that allows you to create various types of documents such as letters, papers, flyers, and faxes. In this lesson, you will
Petrel TIPS&TRICKS from SCM
E&P SOLUTIONS Petrel TIPS&TRICKS from SCM Knowledge Worth Sharing Petrel Studio Part 1 The Petrel Studio was new to Petrel 2011, was augmented with new features in Petrel 2012 and contains a variety of
Desire2Learn: Assignments
Desire2Learn: Assignments Page 1 Table of Contents Assignments... 2 Creating an Assignment folder... 2 To create a new Assignment folder... 2 Editing an Assignment Folder... 2 Assignment Submission Options...
ERPEEG Tutorial. Version 1.0. This tutorial was written by: Sravya Atluri, Matthew Frehlich and Dr. Faranak Farzan.
ERPEEG Tutorial Version 1.0 This tutorial was written by: Sravya Atluri, Matthew Frehlich and Dr. Faranak Farzan. Contact: faranak.farzan@sfu.ca Temerty Centre for Therapeutic Brain Stimulation Centre
Recitation Supplement: Creating a Neural Network for Classification SAS EM December 2, 2002
Recitation Supplement: Creating a Neural Network for Classification SAS EM December 2, 2002 Introduction Neural networks are flexible nonlinear models that can be used for regression and classification
This is a structured tutorial demonstrating the features of the GEdit system. The tutorial guides the designer through three structured examples.
Tutorial on Gedit This is a structured tutorial demonstrating the features of the GEdit system. The tutorial guides the designer through three structured examples. Background GEdit is a program that allows
Navigation in Kuali Research
Navigation in Kuali Research Kuali Research Help Contact: kr-help@umd.edu Last updated: 8/22/17 1 Table of Contents Topic Page Navigation in Kuali Research..3 Lookup Screen Search Techniques.9 2 Navigation
Select the Member. PO Number
Add PO Advanced A new link ADVANCED Add PO has been added. Clicking this link will open a new browser window. From this window you will be able to submit POs much faster as there will be no screen refresh
Volumetric Classification: Program psvm3d
Proximal Support Vector Machine Classification on Seismic Data Program psvm3d Overview Support vector machine (SVM) is a recent supervised machine learning technique that is widely used in text detection,
Chapter 2 Introduction to the Web Browser Interface
Chapter 2 Introduction to the Web Browser Interface This section introduces the web browser interface that enables you to configure and manage your NETGEAR GS700TP Gigabit PoE Smart Switch. Your GS700TP
In the Configuration Tree, right-click Multi-Range and select Create Repository.
Control Center repositories contain configurations that can be applied to multiple managed firewalls. Configuration data that is used on more than one firewall should be stored in a repository to save
Tutorial 3D Max (for beginners) PART I
Tutorial 3D Max (for beginners) PART I The Interface Introduction This tutorial gives a brief explanation of the MAX interface items commonly used and introduces you to the important areas of the interface.
Lionbridge Connector for Episerver CMS 11. User Guide
Lionbridge Connector for Episerver CMS 11 User Guide Version 1.4.2 June 8, 2018 Copyright Copyright 2018 Lionbridge Technologies, Inc. All rights reserved. Lionbridge and the Lionbridge logotype are registered
Geomatica Focus Quick Start Geomatica 2015 Tutorial
Geomatica Focus Quick Start Geomatica 2015 Tutorial Introduction The purpose of this tutorial is to familiarize you with the Geomatica Toolbar, along with visualization of data while using Geomatica Focus.
3 Getting Started with Objects
3 Getting Started with Objects If you are an experienced IDE user, you may be able to do this tutorial without having done the previous tutorial, Getting Started. However, at some point you should read
CHECKING ABBREVIATIONS WITH WORD 2000 BOOKMARKS AND HYPERLINKS
CHECKING ABBREVIATIONS WITH WORD 2000 BOOKMARKS AND HYPERLINKS If you have a List of Abbreviations, you need to check that all the abbreviations used in your text are listed there, and that all abbreviations
CME E-quotes Wireless Application for Android Welcome
CME E-quotes Wireless Application for Android Welcome This guide will familiarize you with the application, a powerful trading tool developed for your Android. Table of Contents What is this application?
We N Depth Domain Inversion Case Study in Complex Subsalt Area
We N104 12 Depth Domain Inversion Case Study in Complex Subsalt Area L.P. Letki* (Schlumberger), J. Tang (Schlumberger) & X. Du (Schlumberger) SUMMARY Geophysical reservoir characterisation in a complex
Title: Interpreter-assisted tracking of subsurface structures within migrated seismic volumes using active contour
Title: Interpreter-assisted tracking of subsurface structures within migrated seismic volumes using active contour Author(s): Muhammad Amir Shafiq * and Ghassan AlRegib Center for Energy and Geo Processing
Unsupervised seismic facies from mixture models to highlight channel features Robert Hardisty* 1 and Bradley C. Wallet 1 1)
Unsupervised seismic facies from mixture models to highlight channel features Robert Hardisty* 1 and Bradley C. Wallet 1 1) University of Olahoma, OK USA Summary Unsupervised seismic facies are a convenient
Volunteer Portal User Guide
Volunteer Portal User Guide Purpose This document serves a guidebook for volunteers to navigate the Volunteer Portal. The Volunteer Portal was established to allow volunteers to access an online account
Tutorial: Analyzing MPI Applications. Intel Trace Analyzer and Collector Intel VTune Amplifier XE
Tutorial: Analyzing MPI Applications Intel Trace Analyzer and Collector Intel VTune Amplifier XE Contents Legal Information... 3 1. Overview... 4 1.1. Prerequisites... 5 1.1.1. Required Software... 5 1.1.2.
Introduction. Getting to Know Word The Ribbon. Word 2010 Getting Started with Word. Video: Exploring Your Word 2010 Environment.
Word 2010 Getting Started with Word Introduction Page 1 Word 2010 is a word processor that allows you to create various types of documents such as letters, papers, flyers, faxes and more. In this lesson,
Sanofi Investigator Sponsored Studies (ISS) External Reference Guide. 1 November 2017
Sanofi Investigator Sponsored Studies (ISS) External Reference Guide 1 November 2017 Sanofi ISS Overview Sanofi is committed to supporting medically and scientifically sound research aimed at the advancement
Anatomy of a Window (Windows 7, Office 2010)
Anatomy of a Window (Windows 7, Office 2010) Each window is made up of bars, ribbons, and buttons. They can be confusing because many of them are not marked clearly and rely only on a small symbol to indicate
TABLE OF CONTENTS. Chapter 8: Miscellaneous Administrative Functions Transferring Cases Between Prosecutors Merging Person Records...
TABLE OF CONTENTS Chapter 8: Miscellaneous...8-1 Transferring Cases Between Prosecutors...8-2 Merging Person Records...8-9 Chapter 8: Miscellaneous Chapter 8: Miscellaneous Miscellaneous Administration
You start model builder through the Geoprocessing > ModelBuilder command:
ESPM5295 ModelBuilder 1 ModelBuilder Automate Processing ModelBuilder is an ArcMap application that you can use to create processing workflows and tools. You can create something like a flowchart on a
Citrix User Guide Version 2.2. Table of Contents. Citrix on a PC... 1
Citrix User Guide Table of Contents Citrix on a PC... 1 Installing Browser Plug-ins... 1 Notes for Windows XP Service Pack 2 Users... 3 Logging In... 3 Accessing Applications... 4 Logging Off... 6 Citrix
BOC USER MANUAL. Bridge Communications
BOC USER MANUAL Bridge Communications +17012124797 www.bridgeoc.com BOC User Manual Table of Contents Main Screen Layout.. 2 Call Control. 3-6 Blind Transfer Supervised Transfer Voicemail Transfer Free
Space Management_. Tips and Tricks_ UniSA All Staff
Space Management_ Tips and Tricks_ UniSA All Staff Contents Click to go to that location in the document: Favourite views... 3 Quick find Room on plan... 4 Quick link to Room record... 5 View plan details
EMERGE Workflow CE8R2 SAMPLE IMAGE. Simon Voisey Hampson-Russell London Office
EMERGE Workflow SAMPLE IMAGE CE8R2 Simon Voisey Hampson-Russell London Office August 2008 Introduction The document provides a step-by-step guide for producing Emerge-predicted petrophysical p volumes
Bentleyuser.dk Årsmøde 2012 Nordic Civil Bentley Civil Workshop
Bentleyuser.dk Årsmøde 2012 Nordic Civil 2012 Bentley Civil Workshop X09 Power Railtrack Presented by: Richard Bradshaw, BSW Development, Civil Design This page left intentionally blank. Workshop: - X09
Welcome to the Enrollee Inquiry Tutorial
Slide 1 - Slide 1 Welcome to the Enrollee Inquiry tutorial. In this tutorial, you ll learn how to inquire about an enrollee's coverage using Employer eservices. Audience: Employers Module Length: Approx.