Built-In Freewheels TYPE
|
|
- Cori Hampton
- 5 years ago
- Views:
Transcription
1 AS TYPE T ype AS is a roller type freewheel non-bearing supported. Bearings are required to support axial and r adial loads. Lubrication and sealing must also be provided by the installation. Nominal outside dimensions are the same as series.. ball bearings. A typical arrangement is to install this type alongside a series bearing within the same location tolerances, as shown on the following page. The inner race is keyed to the shaft (except mm bore). The outer race has a positive R tolerance to give a press fit in a H housing. The outer housing must be strong enough to not expand after assembly. This design can accept an axial misalignment of inner and outer race of ± S/.... P--SC-A /
2 AS AS Type Size Overrunning speeds Weight Drag torque T KN ) n imax ) n amax ) D r D L s e f T R d H [Nm] [min - ] [min - ] [kg] [Ncm], , 0, 0, 0, 0,0 0,, 0 00, 0, 0, 0,0 0,, 00 0,, 0, 0, 0,0 0, 0 00, 0, 0, 0,0 0, 0 0, 0, 0, 0,0 0, , 0, 0, 0,, 0 0,, 0, 0, 0,, AS (NSS) 0 0, 0, 0,, 00, 0, 0,, , 0, 0, 00 0,, 0, 0 0,, 0, 00 0,, 0, ,,, 0, ,,,, NOTES AS without keyway. ØD = -0-0,00 AS- keyway to DIN., other sizes to DIN. ) T max = T KN» Refer to Selection page to MOUNTING EXAMPLE ) Inner race overruns ) Outer race overruns Mounting dimensions are identical to ball bearings series.» Refer to mounting and maintenance instructions page to P--SC-A /...
3 ASNU TYPE T ype ASNU is a roller type freewheel non-bearing supported. Bearings are required to support axial and radial loads. Lubrication and sealing must also be provided by the installation. Nominal outer diameter is the same as a series.. ball bearing. A typical arrangement is to install this type alongside a bearing within the same location tolerances, as shown on the following page. The inner race is keyed to the shaft. The outer race has positive n tolerance, to give a press fit in a H housing. Additional side notches in the outer race provide for positive torque transmission. If the housing is to K tolerance, use of the notches is not necessary, but the housing must be strong enough to not expand after assembly. This design can accept an axial misalignment of inner and outer race of ± S/.... P--SC-A /
4 ASNU ASNU Type ASNU Overrunning Speeds Weight Drag Torque [kg] [Ncm] 0, 0, 0,0, dh TKN) nimax) namax) Dn D L b t s e f [Nm] 0 000,, TR 0 000,, 0, 0, 0,0, 0 00,, 0, 0, 0,, 0 0,,, 0, 0,, 0 0,,, 0, 0,, 00,,, 0, 0,, 0 0 0,,, 0, ,,, 0, 0 0,,, 0, ,,,, 0 0 0,,,, 0 0 0,,,,, 0 00,,,,, ,,,,,0 00 0,0,,, 0 0 0,,,, ,,, ,,, ,, 00 NOTES ASNU-, ASNU0 keyway to DIN., other sizes to DIN. ) Tmax = TKN» Refer to Selection page to MOUNTING EXAMPLE ) Inner race overruns ) Outer race overruns» Refer to mounting and maintenance instructions page to P--SC-A /...
5 AE TYPE T ype AE is a roller type freewheel non-bearing supported. Bearings are required to support axial and radial loads. Lubrication and sealing must also be provided by the installation. Nominal outside diameter is a standard ball bearing dimension. A typical arrangement is to install this type beside a bearing with the same housing diameter tolerance as shown on the following page. The inner race is keyed to the shaft. The outer race has a h tolerance and should be fitted in a housing with a K tolerance. Additional side notches provide for positive torque transmission. If the housing tolerance is to R, use of the notches is not necessary, but the housing must be strong enough to not expand after assembly. This design can accept an axial misalignment of inner and outer race of ± S/.... P--SC-A /
6 AE AE Type AE Size Overrunning speeds Weight Drag torque [kg] [Ncm] 0, 0, dh TKN) nimax) namax) Dh D D L s f e b t [Nm] 0 000, 0, 0, TR 00, 0,,, 0,, , 0,,, 0,, 00 0,, 0, ,,, ,,, ,,,, ,,,, 0,,,, 0 00,,, ,,, ,,,, NOTES MOUNTING EXAMPLE ) Tmax = TKN» Refer to Selection page to ) Inner race overruns ) Outer race overruns Keyway to DIN.» Refer to mounting and maintenance instructions page to P--SC-A /...
7 AA TYPE T ype AA is a roller type freewheel non-bearing supported. Bearings are required to support axial and radial loads. Lubrication and sealing must also be provided by the installation. Standard lubrication is oil. A typical installation is shown on the following page. The inner race is keyed to the shaft. The fit for centering of the outer race must be to H tolerance. Connection of the outer race is via through bolts to grade. or better. This design can accept an axial misalignment of inner and outer race of ± S/.... P--SC-A /
8 AA AA Type AA Size Overrunning speeds) Number dh TKN) nimax) namax) Dh D D D [Nm] 0 0 Z Weight Drag torque [kg] [Ncm], 0, 0, O L f s, 0, TR 00, 0,, 0,, , 0,, 0,0, 000,,, ,,,00 0 0,,, ,,, 0 0,,,00 0 0,,,00 0,, ,, 0 0 0,,, ,,, 0 00,, ,, ,, , , , 0 NOTES MOUNTING EXAMPLE ) Tmax = TKN» Refer to Selection page to ) Inner race overruns ) Outer race overruns Keyway to DIN.» Refer to mounting and maintenance instructions page to P--SC-A /...
9 NF TYPE T ype NF is a roller type freewheel non-bearing supported. Bearings are required to support axial and radial loads. Lubrication and sealing must also be provided by the installation. Standard lubrication is oil. Nominal outside diameter is a standard ball bearing dimension. A typical arrangement is to install this type alongside a bearing with the same housing tolerances, as shown on the following page. The inner race is keyed to the shaft. The outer race has a positive n tolerance to give a press fit in a H housing. A dditional side notches provide for positive torque transmission. If the housing tolerance is to K, use of the notches is not necessary, but the housing must be strong enough to not expand after assembly.... P--SC-A /
10 NF NF Type Size Overrunning speeds Weight dh TKN) nimax) namax) Dn D D L t bh r r [Nm] [kg] ,0, 0, ,0, 0, 00 00,,, 0, 00 00,,0,0 0, ,,0, NF ,,,0, 0 0 0,,, 0 0 0,0,, ,0,, 0 0 0,,,0, ,,0, ,,,, 0 0 0,,, ,0,,0 0 00,,0,0, ,,0,0, ,0,0,0 00 0,0,0,0 NOTES MOUNTING EXAMPLE ) Tmax = TKN» Refer to Selection page to ) Inner race overruns ) Outer race overruns Keyway to DIN.» Refer to mounting and maintenance instructions page to P--SC-A /...
11 S0 TYPE T ype S0 is a non bearing supported sprag type freewheel. The sprags run directly on the shaft provided by the user. Bearings are required to support axial and radial loads. Lubrication and sealing must also be provided by the installation. A typical arrangement is to install this type alongside a bearing as shown on the following page. The housing bore to receive the outer race will be machined with a H tolerance. A key will transmit the torque. The shaft on which the sprags run must have a surface hardness of HRc 0 to for a finished depth of 0, mm minimum. Core hardness should be HRc to. Surface roughness must not exceed CLA. M aximum shaft taper 0,0 mm per 0 mm length. Concentricity between shaft and housing bore should be maintained within TIR 0,0 mm. The preferred lubrication is oil. The Stieber design allows the use of most of the common lubricants used in power transmission including gear oils with EP additives. When necessary grease lubrication is also possible.... P--SC-A /
12 S0 S0 Type Size Overrunning speeds d+0 D L b t [Nm], ,0, -0,0-0,0-0,0-0,0 TKN nmax ) namax Drag torque ) ) Bearing series Weight Tr [Ncm] [kg] 0,0 0, 0,0 0, 0,0 0, 0,0 0,0-0,0 0,0 0,0 0-0,0, 0,0 0, -0,0, 0,0 0, -0,0, 0,0,00-0,0, ,0, ,0 S0, 0 0-0,0, ,0, ,0, ,0, ,0 NOTES MOUNTING EXAMPLE ) Tmax = TKN» Refer to Selection page to ) Inner race overruns ) Outer race overruns» Refer to mounting and maintenance instructions page to P--SC-A /...
13 DC TYPE T ype DC is a sprag type freewheel cage without inner or outer races. It must be installed in a design providing races, bearing support for axial and radial loads, lubrication and sealing. The DC type version-n accepts all types of lubricants currently used in the power transmission equipement. The sprag space tolerance must not be exceeded. Inner and outer races must both have a minimum plain width e, without any recess, to ensure the freewheel functions correctly as shown on following pages. Alternatively, races can be made in case hardened steel shafts, or housings, to the specification below. Surface hardness of the finished part should be HRC 0 to, for a depth of 0, mm minimum. Core hardness to be HRC to. Surface roughness not to exceed CLA. Maximum taper between races: 0,00 mm for mm width.... P--SC-A /
14 DC DC Overrunning speeds Size DCG-N Sprag space + 0,00-0,00 ± 0,0 Number of clips Number of sprags Weight 0,0 TKN) nimax) namax) emin Ødmin Øbmax [Nm] 00 0,,, ±0,0,0 0 Øa Øc [kg] DC-N 0 0,,, ±0,0, 0,0 DC-N 0 0,,000, ±0,0, 0,00 DC(C)-N ,0,, ±0,0, 0,00 DCA-N 000 0,0,, ±0,0,0 0,0 DC(C)-N 00,,, ±0,0, 0,0 DCA-N 0 0,0,, ±0,0,0 0,0 DC(C)-N 0 0,,, ±0,0, 0,0 DCA-N 00,,, ±0,0,0 0, DCA(C)-N 00,,, ±0,0,0 0, DCB(C)-N 00,,, ±0,0,0 0, DCC(C)-N 00,,, ±0,0, 0,0 DCA-N 0 0 0,0,, ±0,0,0 0, DCB-N , 0,000, ±0,0,0 0, DC(C)-N 00,,, ±0,0, 0, DCB-N 00,,, ±0,0,0 0, DCB(C)-N 00,,, ±0,0,0 0, DCC(C)-N 0 00,,, ±0,0, 0, DCC-N 0, 0,000, ±0,0, 0,0 DCA-N 0 0 0,,, ±0,0,0 0, DCA(C)*-N 0 0,**,, ±0,0,0 0 0, DCC*-N ,**,000, ±0,0, 0 0 0,00 DCC(C) 0 0,,0,0 ±0,, 0 0,00 NOTES MOUNTING EXAMPLES ) Tmax = TKN» Refer to Selection page to ) Inner race overruns ) Outer race overruns *) The inner cage centering flange is on the opposite side **) Extension of tolerance to ± 0,0 permissible Other dimensions on request» Refer to mounting and maintenance instructions page to P--SC-A /...
15 DC-RACES TYPE D C races are offered for use with the DC freewheel cages shown on the previous pages. The cage and race assembly, makes a non-bearing supported freewheel. Bearing support for axial and radial loads must be provided, along with lubrication and sealing. The sprag space tolerance must not be exceeded when all bearing clearances and mounting tolerances are considered, (» see table page ). Taper between races should be below 0,00 mm for mm width. Outer races type A and B should be pressed into housings that will not deform after assembly. Please contact our technical department if you need to transmit maximum freewheel torque capacity with A and G type. Key stresses may have to be checked.... P--SC-A /
16 DC-RACES OUTER RACES INNER RACES ) Keyway to DIN. Size Number of holes ø DC A,, DC B, DC C, DC G-,0 DC G-,0 DC G-,0 DC H-,0 DC H-,0 DC H- d H L G L H L J D j T D i + 0,00-0,00 L S An b P t S Bs S Cg DL ±0, D a ± 0,0,0 DC J- 0,0 DC J- 0,0 DC J- 0,0 DC A, DC B, DC C, DC G-, DC G-, DC G-, DC H- 0, DC H- 0, DC H- 0, DC J- 0, DC J- 0, DC J- 0, DC A,, DC B, DC C 0, DC G-0 0, DC G-, DC G-0 0, DC H-0 0, DC H-, DC H-0 0, DC J-0 0, DC J-, DC J-0 0, DC A,, DC B, DC C 0, DC G-, DC G-0 0, DC G-, DC H- 0, DC H-0 0 0, DC H- 0, DC J- 0 0, DC J , Number of holes ø DC A DC A DC A (c) DC (c) DC B DC B (c) DC A (c) P--SC-A /...
17 NFR TYPE T ype NFR is a bearing supported roller type freewheel without any sealing. Lubrication and sealing must be provided by the installation. Standard lubrication is oil. Size to units use steel on steel bearing support from the inner race. Above size, two.. series ball bearings are used, giving a higher overrunning speed capacity. A typical arrangement is shown overleaf. The inner race is keyed to the shaft. The outer race has a positive n tolerance to give a press fit in a housing to H.Additional side notches provide for positive torque transmission.the housing must be strong enough to not expand after assembly.... P--SC-A /
18 NFR NFR -* Type Size d NFR (ANR-ANG) NFR -** H Overrunning speeds Bearing TKN ) nimax ) namax Weight Dn D D L I t r r [kg] *, 0, 00 *, 0, 0 *,,, 0, ) [Nm] b H 0 0 *, 0, ** ,,, ** 0,,, 00 ** 0 0 0,,,, **,,, ** 0 0,,, ** 0 0,,,, 0 00 ** 0,,, ** 0,,,, ** 0,,,, ** 0,,0 0 ** 0 0,,, ** 0,,, 0 00 ** 0,,0 NOTES MOUNTING EXAMPLE ) Tmax = TKN» Refer to Selection page to ) Inner race overruns ) Outer race overruns Keyway to DIN. *) With plain bearing steel on steel **) With ball bearings series.» Refer to mounting and maintenance instructions page to P--SC-A /...
Rotary Ball Spline. With Support Bearing Type Models LTR and LTR-A
With Support Bearing Type Models LTR and LTR-A Outer ring Ball Flange outer ring Seal Seal Retainer Spline nut Spacer Retainer Spline shaft Fig.1 Structure of Model LTR Point of Selection Point of Design
More informationSIZES FROM 1, ,000 Nm BACKLASH FREE, TORSIONALLY STIFF METALLIC BELLOWS COUPLINGS
BX ZA SIZES FROM 1,500-100,000 Nm BAKLASH FREE, TORSIONALLY STIFF METALLI BELLOWS OUPLINGS BELLOWS OUPLINGS BX ZA Optional: GENERAL INFORMATION ABOUT R+W BELLOWS OUPLINGS: SERVIE LIFE R+W bellows couplings
More informationBall Spline Types LT and LF
Ball Spline Types and LF Ball Spline nut Snap ring Seal Retainer Spline shaft Fig. Construction of Ball Spline Type Construction and Features Ball Spline types and LF have four or six trains of loadbearing
More informationHigh Torque Type Ball Spline
58-1E Models LBS, LBST, LBF, LBR and LBH Seal Spline shaft Spline nut Ball Retainer Snap ring Fig.1 Structure of Model LBS Point of Selection Point of Design Options Precautions on Use Accessories for
More informationProduct information PI 54 en Machining unit xxx Slide unit xxx
Product information PI 54 en Machining unit 0.5.030.xxx Slide unit 0.2.200.xxx 2016-03-01 Table of Contents Table of Contents Machining Unit Brief Description...4 Technical Data...6 Dimensions...7 Precision...8
More informationSYMBOLS, UNITS AND DEFINITIONS
SYMBOLS, UNITS AND DEFINITIONS Values depending on the APPLICATION term u.m. definition A 2 [N] Thrust force on output shaft R 2 [N] Radial force on output shaft ED [min] Loading time ED% [%] Loading time
More informationare graded into grades according to mean grading deviation of the nominal ball diameter in the lot D wm Balls
Rolling Elements Balls Balls as a rolling bearing component are made of the same material as bearing rings. The material hardness after processing (hardening) is 61 to 65 HRC. Balls with diameter = 3.175
More informationB-1 SLIDE GUIDE STROKE BALL SPLINE ROTARY BALL SPLINE BALL SPLINE TOPBALL PRODUCTS SLIDE BUSH SLIDE UNIT SLIDEROTARYBUSH STROKE BUSH SLIDE SHAFT
SLIDE GUIDE TOPBALL PRODUCTS SLIDE BUSH SLIDE UNIT B-1 The NB ball spline is a linear motion mechanism utilizing the rotational motion of ball elements. It can be used in a wide variety of applications
More informationYOUR COMPLETE SOURCE FOR. Gear Reducers Couplings & Linear Mount Products. Product Range. GAM Can.
YOUR COMPLETE SOURCE FOR Gear Reducers Couplings & Product Range Linear Mount Products GAM Can. YOUR COMPLETE SOURCE FOR GEAR REDUCERS, COUPLINGS & LINEAR MOUNT PRODUCTS Product Selection Guide Gear Reducers
More informationUNIFLEX TRIPLE SPRING COUPLING
Specialty Couplings Overview Uniflex Coupling Design Flexible Spring Type Coupling with Exclusive Triple Wound Spring Design The Uniflex Coupling is an all steel, single piece coupling that solves a variety
More informationBARE SHAFT PUMPS AND MOTOR PUMPS
APPLICATIONS Air Conditioning Heating and ventilation Refrigeration Fire protection Plumbing Water Circulation Transfer and Irrigation Pressure Boosting Process Industries Water Treatment and Supply DESIGN
More informationSKF hub bearing units for automotive and industrial applications
SKF hub bearing units for automotive and industrial applications Multi-purpose HBU The Power of Knowledge Engineering Table of contents Hub bearing units for automotive and industrial applications Technical
More informationMetric Star Coupling (Plastic "Star" Ring)
Metric Star oupling (Plastic "Star" Ring) H H Finished ore* H H d d Series Max. Max. F / / / 0 7 H Small Hub M 0 H Large Hub M N S L R 0. 7 0 7. / / /0 0 0 0 7 7 0. 0. 0 / /7 7/0 7 7 0 7 0 0 0. 0 Series
More informationThe most common variable when using linear drives is wheter the spindles are driven directly or via toothed-belt. Spindle 16 mm.
Linear drive The most common variable when using linear drives is wheter the spindles are driven directly or via toothed-belt. precise low friction robust economical Spindle 16 mm Ball screw spindle 16
More informationSTRUCTURE AND ADVANTAGES
The NB ball spline is a linear motion mechanism utilizing the rotational motion of ball elements. It can be used in a wide variety of applications including robotics and transport type equipment. STRUCTURE
More informationRA /2.95. Gear Pump Model G2 (Series 4X) For Flange Mounting with SAE threaded Ports. Functional description. Symbols
/2.9 Gear Pump Model G2 (Series X For Flange Mounting with SE threaded Ports s to 22... 6 PSI (2 bar....7 in /rev. (22. cm /rev. /2.9 eplaces: 2.92 New principle of sealing the pump body, increases service
More informationWORKSHOP EQUIPMENT. Engineers Stud. Flanged Nut. T-Slot Nut. Step Block. Extension Nut. Step Clamp
GROUP Indexa T-Slot Clamping Kits Designed to save set up time and solve most T-Slot clamping problems. All components are manufactured from S45C (JIS)/CK45 (DIN) grade non-alloy carbon steel, heat treated
More informationB-1 SLIDE GUIDE STROKE BALL SPLINE ROTARY BALL SPLINE BALL SPLINE TOPBALL PRODUCTS SLIDE BUSH SLIDE UNIT SLIDEROTARYBUSH STROKE BUSH SLIDE SHAFT
SLIDE GUIDE STROKE TOPBALL PRODUCTS SLIDE BUSH SLIDE UNIT B-1 The NB ball spline is a linear motion mechanism utilizing the rotational motion of ball elements. It can be used in a wide variety of applications
More informationContents. Page 2 TRCTFP101
Contents CHAINS SPZ-SPA-SPB-SPC Profile Selection 3 Taper Bore SPZ 4-7 Taper Bore SPA 8-10 Taper Bore SPB 11-14 Taper Bore SPC 15-17 Taper Bushes 18-19 Taper Bushes - Metric 20-23 Taper Bushes - Imperial
More informationMechanical accessories
Bearing box Part no. 01209010, 01209029 Part no. 01209010 01209029 Shaft size Ø 15 mm Ø 10 mm Shaft load max Radial: 250 N, Axial: 150 N Speed max 4000 rpm Protection class IP 64 according to IEC 60529
More informationKEDRON BEARINGS SERVICES LLC. General catalog
KEDRON BEARINGS SERVICES LLC General catalog INTRODUCTION KBS Kedron Bearing Systems LLC is a manufacturer of high grade bearing parts and complete range ball and roller bearings. KBS has achieved global
More informationBTL. Taper bushing A. PLATE SPROCKET REBORE TO "G"DIMENSION. WELD TAPER WELD. ON HUB TAPER SPROCKET
is a new type of component used for joining mechanical transmission. It changed from the traditional design and now features easy-on, easy-off construction and high standardization. The grip is tightened
More informationRotary Measuring Technology Absolute encoders, Singleturn, Profibus-DP
Safety-Lock TM High rotational speed Temperature High IP High shaft load capacity Shock/vibration resistant Magnetic field proof Short-circuit proof Reverse polarity protection Reliable Increased ability
More information50 years of Reliable Field History
COUPLING COMMENTS The No Maintenance, Easy Assembly, Resilient Coupling with High Angular Misalignment up to 0 degrees Center Assembly 70 Deg. Neoprene Rubber in Compression Grade 5 Bolts Steel Flanges
More informationKISSsoft Tutorial: Roller Bearings
KISSsoft Tutorial 007: Roller Bearings KISSsoft AG - +41 55 254 20 50 Uetzikon 4 - +41 55 254 20 51 8634 Hombrechtikon - info@kisssoft. AG Switzerland - www. KISSsoft. AG KISSsoft Tutorial: Roller Bearings
More informationEncoder WDGA 58B CANopen
Encoder WDGA 58B CANopen www.wachendorff-automation.com/wdga58bcan Wachendorff Automation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard range and
More informationABSOLUTE ROTARY ENCODER ETHERNET/IP
Main Features - Compact and heavy duty industrial model - Interface: EtherNet/IP - Conformance tested by ODVA - Housing: 58 mm - Full shaft: 6 or 10 mm / hollow shaft15 mm - Resolution: max. 30 Bit = 1,073,741,824
More informationRotary Measuring Technology Absolute encoders, Multiturn, Profibus-DP
Mechanical drive Safety-Lock TM High rotational speed Temperature High IP High shaft load capacity Shock/vibration resistant Magnetic field proof Short-circuit proof Reverse polarity protection Reliable
More informationL4 Min. L2 Stroke Length. SDM Ø16x5/10/ M5x L1-294
Hepcootion SD - Screw Driven odule The Hepcootion SD range has been based on the popular SBD range of belt driven linear actuators but incorporates a ballscrew into the design. This allows for improved
More informationData Sheet MEM 16. Absolute Encoder Multiturn
Absolute Encoder Multiturn Features Resolution: Singleturn: up to 8,192 (13 Bit) steps per revolution Multiturn: up to 4,294,967,296 (32 Bit) revolutions Interface: SSI (synchron serial interface) or BiSS
More informationWaterproof Bearings Designed for demanding environments
Waterproof Bearings Designed for demanding environments /// Flange bearings /// Pillow block bearings /// Solid housings /// Easy assembly Vill du veta mer ring: 019-12 77 96 /// USDA accepted /// Food
More informationBlock type Linear Ball Spline
U.S. PATENTE Block type Linear Ball Spline Block type Linear Ball Spline is a linear motion rolling guide, featuring a slide unit which performs endless linear motion along a spline shaft. Two rows of
More informationS. S. Bari 1, D. H. Burande 1, M.R. Birajdar 2
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) ISSN(e) : 2278-1684, ISSN(p) : 2320 334X, PP : 39-43 www.iosrjournals.org Design and Analysis of Barrel Coupling S. S. Bari 1, D. H. Burande
More informationILA1F572PB1A0 integrated drive ILA with servo motor V - CANopen - PCB connector
Characteristics integrated drive ILA with servo motor - 24..36 V - CANopen - PCB connector Main Range of product Product or component type Device short name Motor type Number of motor poles 6 Network number
More informationGEAR DESIGN SOLUTIONS
GEAR DESIGN SOLUTIONS Release 5.0 2012 Dontyne_Brochure2012.indd 2 28/08/2012 09:59 Dontyne SyStems Dontyne Systems offers software and services aimed at the optimum production of gear components and their
More informationRadial Piston Hydraulic Motor with Fixed Displacement MR, MRE
+ (0)0 69999 Radial Piston Hydraulic Motor with Fixed Displacement MR, MRE RE 8 Issue: 08.0 Replaces: 08.008 Sizes to 00 Nominal pressure 0 bar Maximum pressure up to 00 bar Displacement up to 090 cm orque
More informationn Measuring range 0... ± 0,02 Nm to 0... ± 1000 Nm n Low linearity deviation of ± 0.05 % F.S. n Intelligent operating state indicator
Precision Torque Sensor Non-contact transmission for rotating applications Optional measurement of angle and speed Model 8661 Code: Delivery: Warranty: 2-3 weeks 24 months Optional: USB interface Dual
More informationData Sheet MEM 22. Absolute Encoder Multiturn
Absolute Encoder Multiturn Features Resolution: Singleturn: up to 16,384 (14 Bit) steps per revolution Multiturn: up to 16,777,216 (24 Bit) revolutions Interface: SSI (synchron serial interface) or BiSS
More informationFeatures: Quality Testing and Documentation
1 The Yokogawa Falcon Series Dual Chamber Orifice Assembly YFOM-DC, is suitably designed for on-line retraction and inspection of orifice plates in process full flow and pressure conditions. The orifice
More informationLevel switch NS 10/NS 25..-AM
Level switch NS 10/NS 25..-AM Fluidcontrol Oil tanks in lubrication and oil supply systems are often under overpressure compared to the ambient atmosphere. All oil moistened parts of devices mounted externally
More informationRexroth Linear Bushings and Shafts, GreenLight Selection
4 Bosch Rexroth Corp. Linear Motion and Assembly Technologies Rexroth Linear Bushings and Shafts, GreenLight Selection Bosch Rexroth is the global leader in metric bushings. Whether you need standard bushings
More informationAsynchronous motors. 5/48 Permissible combinations of mechanical designs for 1PL6 motors,
Asynchronous motors 5 Asynchronous motors 5/2 Type overview and rated data 5/4 Technical definitions 5/4 Encoder systems 5/5 1PH7 motors 5/5 1PH7 motors, forced ventilation 5/32 Permissible combinations
More informationGEAR DESIGN SOLUTIONS
GEAR DESIGN SOLUTIONS Release 5.0 2013 Dontyne SyStems Dontyne Systems offers software and services aimed at the optimum production of gear components and their use in the transmission industry. Our range
More informationShaft-hub connections
Product description PG- and P4C-Polygon profile, splined shaft, muff coupling INKOMA shaft-hu connections provide for cost saving design, using assemly ready standardised components, without compromising
More informationنﺎﻤﻟ آ ﻲﻧﺎﭙﻤﻛ يرﺎﺼﺤﻧا هﺪﻨﻳﺎﻤﻧ
ا زما صنعت گراد Mahr MARSHAFT I MANUAL SHAFT MEASURING UNITS V02-May 2009 MarShaft MAN Data Sheets 1 MarShaft MAN Shaft Measuring Unit Advantages at first sight A measuring instrument for multiple measuring
More informationHeat Exchanger Condenser Expanders
Heat Exchanger Condenser Expanders The world standard in tube expanders Airetool heat exchanger and condenser expanders have long been recognized as the standard to which all other brands are measured.
More informationFEATURES APPLICATIONS OPERATING DATA MATERIALS OF CONSTRUCTION. Flood control
APPLICATIONS FEATURES Flood control Irrigation Land drainage Pollution control Industry Water refineries Water parks Design OPERATING DATA Capacity:...up to.000 m/h Head:...up to m Max. water temperature:...0
More informationRadial Piston Hydraulic Motor with Fixed Displacement MR, MRE
Radial Piston Hydraulic Motor with Fixed Displacement MR, MRE RE 8 Issue: 09.0 Replaces: 08.0 Sizes to 00 Nominal pressure 0 bar Maximum pressure up to 00 bar Displacement up to 090 cm orque up to 800
More informationEncoder WDGA 58A CANopen
Encoder WDGA 58A CANopen www.wachendorff-automation.com/wdga58acan Wachendorff Automation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard range and
More informationEncoder WDGA 58B SSI.
Encoder WDGA 58B SSI www.wachendorff-automation.com/wdga58bssi Wachendorff Automation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard range and customer
More informationRoller Rail Systems. (Additional roller runner blocks SNS R1822, SLS R1823, FXS R1854) R310EN 2315 ( ) The Drive & Control Company
Roller Rail Systems (Additional roller runner blocks SNS R18, SLS R183, FXS R1854) R31EN 315 (1.9) The Drive & Control Company Bosch Rexroth AG Linear Motion and Assembly Technologies Ball Rail Systems
More informationFlexible claw couplings ELKU-N
Flexible claw couplings ELKUN KWN 01 Couplings from Dresden / Germany By specialists for specialists řemeny, převody a lineární technika general information buffer part hub technical features The flexible
More informationHigh Torque Type Ball Spline
0 Torque Type Ball Spline High Torque Type Ball Spline Model LBS, LBF, LBH, LBST and LBR Models LBS, LBF, LBH, LBST and LBR Seal Spline nut Spline shaft Ball Snap ring Retainer Structure and Features Fig.1
More informationMembers: Sponsor: Dalton Hamilton Preston-Eastin Levi Edens Kenneth Mui Brice Abbott
Members: Dalton Hamilton Levi Edens Brice Abbott Sponsor: Preston-Eastin Kenneth Mui Mission Statement Wolf Pack Engineering strives to provide our customer with innovative solutions. We take a cost effective
More informationTECHNICAL DATASHEET Absolute Motorfeedback Series AD 34
For brushless servo motors Light duty encoder Unique mounting concept: Save installation time and cost Mounting Depth: 25 mm (ST), 34 mm (MT) Up to 9 Bit ST - resolution + 2 Bit MT - resolution +20 C operating
More informationEncoder WDGA 58A PROFINET-IO (cov)
Encoder WDGA 58A PROFINET-IO (cov) www.wachendorff-automation.com/wdga58apnb Wachendorff Automation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard
More informationThis is trial version
s, s, Ejector coupling devices, Unscrewing components, Two-stage ejectors, Latch locking units, Mould slides-modular system 2.01 2.02 Ordering example : Z 40 / 1,6 x 40 Shaft Overall length Z02/... 2.1
More informationClamping Systems. PClamp. PClamp N. PClamp E. Gewährleistung. Inhalt. RotoClamp. DiskClamp. LinClamp. PClamp
Gewährleistung Inhalt N dvantages 1 Pneumatic clamping with high forces General information 2 Optimum safety clamping pneumatic failure locks the system The performance of hydraulic clamps will be achieved
More informationRACO-ELECTRIC CYLINDER MODULAR SYSTEM HEAVY DUTY SERIES (TYPE 1) SIZE 4,5,6,7,8
SIZE,,,, HIGH-PERFORMANCE ELECTRIC CYLINDERS: ROBUST, RELIABLE AND FLEXIBLE RETRO-FITTING The RACO actuator system is of modular design, and thus enables the combination of the most important integral
More informationProduct Information ROC 425 ROQ 437. Absolute Rotary Encoders with EnDat 2.2 for Safety-Related Applications
Product Information ROC 425 ROQ 437 Absolute Rotary Encoders with EnDat 2.2 for Safety-Related Applications 10/2016 ROC 425, ROQ 437 with synchro flange Rotary encoders for absolute position values with
More informationENCODER. Profibus Multiturn. Series , Key-Features:
ENCODER Profibus Multiturn Series 8.5868, 8.5888 Key-Features: Content: Order Code Technical Data Profibus Interface Connection Technical Drawing......3...4...4...5 - Solid shaft: maximum diameter 0 mm
More informationТел. (499) Ball Rail Tables TKK
Ball Rail Tables TKK 2 Bosch Rexroth Corporation Ball Rail Tables TKK R310A 2501 (2007.10) Rexroth Linear Motion Technology Ball Rail Systems Roller Rail Systems Linear Bushings and Shafts Standard Ball
More informationNUMERICAL ANALYSIS OF ROLLER BEARING
Applied Computer Science, vol. 12, no. 1, pp. 5 16 Submitted: 2016-02-09 Revised: 2016-03-03 Accepted: 2016-03-11 tapered roller bearing, dynamic simulation, axial load force Róbert KOHÁR *, Frantisek
More informationWorkholding. Workholding CHUCKS CENTRES 3-JAW SELF CENTERING MONO-BLOCK JAW CHUCKS STEEL CENTRES 60º PLAINBACK FITTING CARBIDE CENTRES 60º
CENTRES CHUCKS STEEL CENTRES 60º 3-JAW SELF CENTERING MONO-BLOCK JAW CHUCKS CARBIDE CENTRES 60º Taper Stock Code MT1 014-101 0.25kg MT2 014-102 0.25kg MT3 014-103 0.5kg MT4 014-104 1kg MT5 014-105 2.5kg
More informationACCESSORIES. Setscrew Ball Bearings LUBRICANTS AIR HANDLING SEALS HOUSING MATERIAL HIGH TEMPERATURE OTHER MODIFICATIONS
Setscrew Ball Bearings LUBRICANTS DODGE ball bearings are factory lubricated with a lithium complex base lubricant. For applications where extreme ambient temperatures or speeds are anticipated or environmental
More informationABSOLUTE ROTARY ENCODER INTERBUS
Main Features - Compact and heavy duty industrial model - Interface: Remote-Bus - ENCOM-Profile: K (programmable) - Housing: 58 mm - Shaft: 6 or 10 mm, hollow- 15 mm - Resolution: max. 25 Bit =,554,42
More informationEncoders Absolute Singleturn Encoder Types A58CS8
Types A58CS8 Sturdy design with hardened bearings High rotation speed -40...+80 C/-40...+76 F operating temperature range High shock and vibration resistance Magnetic field proof also available as explosion
More information8661 EN. Precision Torque Sensor Non-contact transmission for rotating applications optional measurement of angle and speed.
Precision Torque Sensor Non-contact transmission for rotating applications optional measurement of angle and speed Model 8661 Code: Delivery: Warranty: 1-2 weeks 24 months Application The series 8661 precision
More informationC-Lube Linear Ball Spline MAG
U.S. PENED -Lube Linear Ball Spline F -Lube Linear Ball Spline series Shape Length of external cylinder Shaft shape Maintenance free type has been released for -Lube Linear Ball Spline having an overwhelmingly
More informationIncremental encoders Solid shaft with EURO flange B pulses per revolution
Solid shaft with EURO flange B 0 5000 pulses per revolution EIL580 - EURO flange B - OptoPulse Features Size ø58 mm Precise optical sensing Output signal level TTL or HTL EURO flange B Connection axial,
More informationHB5M. Hollow Bore Optical Encoder Page 1 of 5. Description. Mechanical Drawing. Features
Description HB5M Page 1 of 5 The HB5M is a hollow bore (hollow shaft / thru-bore) optical encoder with a machined aluminum enclosure and an anodized protective finish. The HB5M optical incremental encoder
More informationCLAMSHELL PIPE CUTTING AND BEVELLING MACHINES. Mactech Europe LTD
CLAMSHELL PIPE CUTTING AND BEVELLING MACHINES Mactech Europe LTD Mactech s Clamshell lathes are portable pipe cutting machines designed for on-site precision severing, severing/beveling, and severing/double
More informationProduct Overview. Product Overview. How To Order. Flange Input - Shaft Output Right Hand Output. Flange Input - Shaft Output.
Product Overview Product Overview Flange Input - Shaft Right Hand Flange Input - Shaft Double End Shaft Input - Shaft Left Hand How To Order 5:1-60:1 ratios sizes 1.33-3.25 One piece # Fc20 all cast iron
More informationEncoder WDGA 58A RS485
Encoder WDGA 58A RS485 www.wachendorff-automation.com/wdga58ars485 Wachendorff Automation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard range and
More informationRotary Position Technology Incremental Encoders
-40 to 85 C IP Bearing-Lock High rotational speed Temperature High IP High shaft load capacity Shock/vibration resistant Magnetic field proof Short-circuit protected Reverse polarity protection Optical
More informationTechnical details for tools from our manufacturing inventory
Technical details for tools from our manufacturing inventory The workpieces to be broached shall be clean and free of burrs. The pre machined bore diameter shall be within the tolerances we give. In case
More informationBALL SPLINE ROTARY BALL SPLINE STROKE BALL SPLINE B-1 BALL SPLINE
ROTARY STROK B- Authorised distributors for over manufacturers Acorn Industrial Services Ltd Central distribution centre Divisions Acorn CDC T north@acorn-ind.co.uk www.acorn-ind.co.uk/north Linear Division
More informationSERIE 59. Rear clamp. Frontal clamp HIGH RESOLUTION HOLLOW SHAFT INCREMENTAL ENCODER FOR INDUSTRIAL APPLICATIONS
HIGH RESOLUTION HOLLOW SHAFT INCREMENTAL ENCODER FOR INDUSTRIAL APPLICATIONS Resolution up to 50.000 pulses per turn External diameter 58 mm Hollow shaft from Ø 10 to 14 mm Protection class IP67 according
More informationManual Clamps for Automotive Prototype Production
Manual Clamp interchangeable with 82M-6 This newest version provides more clamp arm variations and in addition two hold open devices. Opening angle can be reduced now. Page 15.2 New products 15.0 Notes
More informationPN Gold Mounted Ball Bearings
PN Gold Mounted Ball Bearings PN Gold with high strength reinforced composite housing PN Gold with 1 passivated stainless steel housing PN Gold Extended Bearing Life for Highly Corrosive Environments Reinforcing
More informationEncoder WDG 40E.
Encoder WDG 0E www.wachendorffautomation.com/wdg0e Wachendorff utomation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard range and customer versions
More informationLinear Ball Spline. C-Lube Linear Ball Spline MAG Linear Ball Spline G Block Type Linear Ball Spline Stroke Ball Spline
Linear Ball Spline -Lube Linear Ball Spline MAG Linear Ball Spline G Block Type Linear Ball Spline Stroke Ball Spline Features of Linear Ball Spline series Excellent features of compact linear ball spline
More informationThe contact analysis for Barrel coupling based on Ansys
ISSN 235-1621 The analysis for Barrel coupling based on Ansys #1 V.V.Vaidya, #2 A.P.Tadmalle 1 vikrant.vaidya27@gmail.com 2 aptadmalle.scoe@sinhgad.edu 1 Sinhgad College of Engineering, 2 Sinhgad College
More informationRotary Position Technology Incremental Encoders
-40 to 85 C IP Safety-Lock High rotational speed Temperature High IP High shaft load capacity Shock/vibration resistant Magnetic field proof Short-circuit proof Reverse polarity protection Optical sensor
More informationAbsolute Encoders Multiturn
The multiturn encoders 5868 and 5888 with interface and optical sensor technology are ideal for use in all applications with a interface. The encoder supports the isochronous (IRT) mode and is therefore
More informationILS1M851PB1F0 integrated drive ILS with stepper motor V - I/O for motion sequence - 5A
Characteristics integrated drive ILS with stepper motor - 24..36V - I/O for motion sequence - 5A Main Range of product Product or component type Device short name Motor type Number of motor poles 6 Network
More informationEncoder WDGA 36A CANopen
Encoder WDGA 36A CANopen www.wachendorff-automation.com/wdga36acan Wachendorff Automation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard range and
More informationENGINEERING MEASUREMENTS ENTERPRISE LTD. TECHNICAL REPORT RESULTS OF DEVIATION MEASUREMENTS AND GEOMETRY OF ROTARY KILN GEOCEMENT PLANT
GEOSERVEX s.c. Zbigniew i Boleslaw Krystowczyk e-mail: office@geoservex.com.pl http://www.geoservex.com.pl office: ul. Kościuszki /19A 8-9 Bydgoszcz, POLAND tel: (+48) 34 6 fax: (+48) 34 6 EU VAT ID No:
More informationENC-IQ58S-H-PROG-ZCW-4-06-A-L1
IQ58/ IQ58S/ CKQ58 Hollow Shaft Magnetic Encoder Series FEATURES Programmable Incremental Encoder Resolution from 1 to 16384 PPR Selectable Index length 90 or 180 el. Push-Pull and Line Driver Compatible
More informationStress Analysis of Cross Groove Type Constant Velocity Joint
TECHNICAL REPORT Stress Analysis of Cross Groove Type Constant Velocity Joint H. SAITO T. MAEDA The driveshaft is the part that transmits the vehicle's engine torque and rotation to the tires, and predicting
More informationEncoder WDGA 36A SSI.
Encoder WDGA 36A SSI www.wachendorff-automation.com/wdga36assi Wachendorff Automation... systems and encoders Complete systems Industrial rugged encoders to suit your application Standard range and customer
More informationVOL.3. New models are introduced! Wide range of variations! nd Metrics. Linear Ball Spline G CAT U.S. PATENTED
VOL. New models are introduced! Wide range of variations! Linear Ball Spline G CAT-57117 U.S. PATENTED 1 Linear Ball Spline Linear Ball Spline G Block type Linear Ball Spline Linear Ball Spline G and Block
More informationBall valve Metal. Sectional view. * see information on working medium on page PED/97/23/EC Category III Module H TA-LUFT
all valve Metal Construction GEMÜ is a 2/2-way stainless steel ball valve with top flange EN ISO 5211 in sizes DN 15 to 100. It has a low maintenance electric actuator with a powerful DC motor. The reduction
More informationMechanical and adapters
Pneumatic expansion shafts Mechanical expansion shafts Expansion couplings Expansion chucks and adapters Friction and knife shafts Shaft handling Expansion chucks and adapters E X P A N S I O N U N I T
More informationENC-CKP58-H-PROG-ZCW-4-06-A-L1
IP58/IP58S/CKP58 Programmable Incremental Encoders FEATURES Programmable Incremental Encoder Resolution from 1 to 65536 PPR Voltage 5 VDC or 10-30 VDC Push-Pull and Line Driver Compatible Output IP 65
More informationAccessories. Measuring wheels Order designations. Measuring wheel with 20 cm circumference (small)
Accessories Measuring wheels s Measuring wheel with 20 cm circumference (small) 04 Bore 4 mm (Standard) 05 Bore 5 mm 06 Bore 6 mm 07 Bore 7 mm 10 Bore 10 mm Material, Surface MR211. A Aluminum, cross knurl
More informationAbsolute Encoders Multiturn
The Sendix multiturn encoders 5868 and 5888 with CANopen or CANlift interface and optical sensor technology are the right encoders for all CANopen or CANlift applications. With a maximum resolution of
More informationTORQUE LIMITER SERIES 200
TORQU LIMITR SRIS 00 Quality and Autogard are synonymous with overload protection. The company's reputation for high quality products is derived from over 40 years of design innovation and production.
More informationNOVOHALL Rotary Sensor non-contacting. Series RSX-7900
NOVOHALL Rotary Sensor non-contacting Series RSX-7900 Special features very robust design to extreme environmental conditions high shaft load 300 N non-contacting, magnetic measuring angles up to 360 in
More informationLink-Belt Centrik-Lok CL Series Overview. Link-Belt Centrik-Lok CL Series
Link-elt Centrik-Lok CL Series Overview Link-elt Centrik-Lok CL Series Rexnord proudly introduces an improved design for concentric locking mounted ball bearings. Utilized in demanding applications that
More information