Alpha-Numeric Display Pager MODEL :AL-A28. Gold Apollo Co., Ltd.

Transcription

1 Alpha-Numeric Display Pager MODEL :AL-A28 PAGER PROGRAMMING GUIDE Gold Apollo Co., Ltd.

2 Contents Contents GETTING STARTED... 1 EQUIPMENT REQUIRED... 1 EQUIPMENT SETUP... 1 INSTALLING PROGRAMMER SOFTWARE... 3 INSTALLATION... 3 RUNNING... 6 ALA28 PROGRAMMING... 7 INTRODUCTION... 7 STARTING THE PROGRAMMER... 7 CODE AND FEATURES MENU... 9 Frequency... 9 Capcode (Decimal Address) Auto Increase 1 after write ALERT AND STATUS Alerts and Status Manual Write...15 Prompts...16 Out of Range Prompts...16 FILE OPEN (CTRL + O)...17 FILE SAVE (CTRL + S)...17 FILE EXIT (CTRL + E)...17 PAGER READ (F3)...17 PAGER WRITE (F4)...19 ABOUT...20 V1.0

3 Getting Started Getting Started The ALA28 pager Programming software, provides the flexibility to program ALA28 pagers to meet individual requirements. To obtain the best results from the product, please take a few minutes to read this instruction guide. Equipment Required To install and operate the programmer, you need a system that meets the following minimum requirements: An personal computer (PC) with printer port, or compatible Windows 98 SE or above operating system (XP Recommended) 256 MB of RAM ALA28 Programmer A DB25 male-male printer cable ALA28 Pager Programming Software Equipment Setup Refer to Figure 1 while performing the follows: 1. At the rear of the PC, connect the DB25 male-male interface cable to the printer port on your computer. 2. Plug end of the DB25 cable into the ALA28 programmer. 3. Hardware installation is complete. 1

4 ALA28 Getting Started Power LED Press down on the pager until it is tight in the fixture. Computer ALA28 Programmer DB25 male-male printer cable AL-A28 Figure 1 Programmer Hardware Connections 2

5 Installing Programmer Software Installing Programmer Software Installation Install the programmer software into a PC as follows: 1. Uncompress the ALA28FV3.81_FD0801.zip and save them in a temporary directory. 2. Double click the setup.exe file. Click on Y. 3. Click Next on the Welcome screen. 4. Enter your user information and click Next. (Note: you must enter at least a single character "into the company field) 3

6 Installing Programmer Software 5. Choose where the program should be installed and click Next. 6. On the Select Program Folder screen choose where you would like the program to show up in your start menu and click Install. 4

7 Installing Programmer Software 7. Click Finish on the Setup Complete screen. 5

8 Installing Programmer Software Running You now have the program installed. To run it from the Start menu/programs / Gold Apollo /ALA28 Pager Programmer 6

9 Introduction Starting the Programmer Preparing a Pager for Reading or Programming: Establish a computer hardware configuration. Run the programming software of ALA28. A Power LED illuminates on the Programming Interface to indicate proper contact. If the Power LED did not illuminate then you must check the configuration and restart the programming software of ALA28. Align the pager contact pin holes with the contact pins of the ALA28 Programmer. Press down on the pager until it is tight in the fixture. Turn the pager off or wait the pager until standby mode. The pager is now ready to read or program. The application can be launched from Start Programs Gold Apollo ALA28 Pager Programmer. The following window appears : Input your password. If key in wrong password for 3 times, the system shuts off automatically. If the password is correct, the following window appears : 7

10 Now, the system examines that the ALA28 programmer is well installed. If any questions, the following window appears : Please re-check the ALA28 programmer and printer port are well installed or not. If connection successfully with the ALA28 programmer. The system enters the Code and Features Menu 8

11 Code and Features Menu Frequency You can select the range of frequency and all setting will load default value. The frequency is on which the pager operates. The baud rate is on which the pager operates. 9

12 Capcode (Decimal Address) Cap #1 st Please input 1 Capcode (7 Dec digits between 8 and ). ON nd Enable or disable 2 Capcode (address). Click to set function bit (A B C D) message control. 10

13 Function Bit (A B C D) Message Display: N: STD Number. P: PRC Number. A: Alpha number. I: Ideographic. T: Tone only D: Disable Function Bit (A B C D) Priority Alert: - is disable. Function Bit (A B C D) Message Type: P: Personal. 11

14 The available selections for alerts are: 02: 2 sec. 08: 8 sec. 16: 16 sec. 32: 32 sec. CT: continuous. Auto Increase 1 after write st 1 capcode always increment by one after write. nd 2 capcode always increment by one after write. 12

15 Alert and Status Alert and Status If it is selected, then the message most length is 2,000 characters, otherwise the length only can be 300 characters. If it is selected, error message will be discarded. This value represents the battery voltage level necessary for the battery gauge to display a full battery. If the battery voltage is higher or equal to this value, the full battery gauge icon is displayed. Valid selections are: 1.58V, 1.53V, 1.48V, 1.43V, 1.39V, 1.35V, 1.29V, 1.23V, 1.19V, 1.14V, 1.09V, 1.05V, and 1.00V. The High level must be greater than the Med level, and the Med level Must be greater than the Low level. None of the levels can be equal to each other. 13

16 This value represents the battery voltage level necessary for the battery gauge to display a full battery. If the battery voltage is higher or equal to this value, the full battery gauge icon is displayed. Valid selections are: 1.58V, 1.53V, 1.48V, 1.43V, 1.39V, 1.35V, 1.29V, 1.23V, 1.19V, 1.14V, 1.09V, 1.05V, and 1.00V. The High level must be greater than the Med level, and the Med level Must be greater than the Low level. None of the levels can be equal to each other. This value represents the battery voltage level necessary for the battery gauge to display a full battery. If the battery voltage is higher or equal to this value, the full battery gauge icon is displayed. Valid selections are: 1.58V, 1.53V, 1.48V, 1.43V, 1.39V, 1.35V, 1.29V, 1.23V, 1.19V, 1.14V, 1.09V, 1.05V, and 1.00V. The High level must be greater than the Med level, and the Med level Must be greater than the Low level. None of the levels can be equal to each other. When the paging display is Direct, if it is selected, the back-light will turn on at a message received. If it is selected, the pager emits a, low battery cell alert when the battery reaches a low cell state. It select the RF signal polarity is normal or invert. With an out-of-service time specified by the code plug, the pager is considered out of service when it does not detect a POCSAG synchronization word for that time period. The out-of-service icon displays at this time. Valid selections are: disabled, 1 min, 2 min, 5 min and 10 min. 14

17 It selects the LCD display contract level. The value is a sequential lockout timer begins when a message arrives and is flagged as being sequentially locked out. If duplicate messages arrive, one of the messages is disregarded and not flagged as a duplicate. Valid selections are disabled, 30 seconds, 60 seconds, 120 seconds, 175 seconds and 240 seconds. With this option selected, the time period begins with a newly arrived message and is reset every time a new message is received. Once the time period expires, the pager does not emit any more reminder alerts until a new message arrives. Valid time period selections are: Disable, 2 minutes, 10 minutes and 60 minutes. It is used for the user s manual programming. Manual Write If it is selected, manual write enable. If it is selected, frequency modification is enabled at manual programming. If it is selected, enters manual programming password is required. If it is selected, enters manual programming password can be modification. 15

18 Prompts Out of Range Prompts 16

19 File Open (Ctrl + O) Click Open or Ctrl + O to open the ALA28 code-plug file. The file has the extension.tbl. File Save (Ctrl + S) Click Save or Ctrl + S, save the current code-plug data to a file. File Exit (Ctrl + E) Pager Read (F3) Exit the programmer software. Click Read or press F3 to read code-plug data from a ALA28. The status window shows reading process, when it's done, you will see a message window of Read success on the screen. 17

20 18

21 Pager Write (F4) Click Write or press F4 to program the ALA28. The status window shows the writing process. When writing process finished, will starting verify process, when it is done, you will see a window of Verify success on the screen. 19

22 About About the ALA28 Pager Programmer software information. 20