TYPE-81C Administrator menu

Transcription

1 OME Direct Core Monitoring Optical Fiber Fusion Splicer TYPE-81C Administrator menu Operation instructions

2 Table of contents Overview 1 Accessing administrator menu 1 Administrator menu details 2 Changing settings 5 Analyzing fiber type 8 Registration of splice program 8 Release of splice program 10 Security (startup password protection) 11

3 Overview The administrator menu enables setting up further detailed functions. The access to the menu is limited by pass code. Accessing administrator menu DATA Splice Data USB Function Login Menu Maintenance Information 2011/01/01 00:00 Security 1: Touch Login icon ( ) on the menu screen Login Pass Code Input Number Input Pass Code screen Pass code: OK 2: 0000 is shown from the beginning. Touch OK. DATA Splice Data USB Function Login Menu Maintenance Information 2011/01/01 00:00 Security 3: The menu screen is displayed again when the pass code is accepted. 4: In administrator menu, you can change extra items of splice programs and heating programs as described next few pages what are not appeared in normal menu. About changing items, please refer to page 4-6 of operation manual. Tips Once you enter the Pass Code, you can access the administrator menu without re-entry of the Pass Code unless you turn off the power. If you turn off the power and turn it on again, the operator menu is displayed. 1

4 Administrator menu details Page Splice program items in administrator menu 1/5 <Fusion Time> Fusion time is the duration of arc discharge. (Numerical input) <Prefusion Time> Pre-fusion time is the time in seconds the fiber ends wait after the arc discharge begins before beginning the overlap (feed). (Numerical input) <Arc Gap> Arc gap is the distance between the left and right fibers before fusion takes place. (Numerical input) <Over Lap> Overlap is the amount of overlap between the left and right fibers that occurs when the right fiber is fed forward during the arc fusion. (Numerical input) 2/5 <Arc Power> Expressed in a unit-less step value as [Standard +XX]. Arc power controls the amount of heat the fibers are exposed to during the fusion arc. As the power is automatically set after an arc test and compensated at every splices, normally an operator does not need to change it manually. Standard means compensated arc power of the splice program, and added value can be manually set by operator. (Numerical input) <Staying Time> Staying time is the duration from the end of overlap to the beginning of pulling. Only for Fiber pulling splice. (Numerical input) <Fiber Pulling> Fiber pulling is the amount of pulling the fiber back after overlap. (Numerical input) <Arc Center> Arc center is the position of the arc center. Usually it is set automatically by the splicer. (Numerical input) Go on to the next page. 2

5 3/5 <Splice Select> Select the splice mode from Automatic, Manual and Quick. (Icon selection) Automatic APDS is used and automatic splice is performed. Manual Splice is performed by manual operation with key pad. Quick APDS is not performed. Inspections are simplified and automatic splice is performed. <Align Method> Select the fiber aligning method from Core, Diameter, AIAS, ATTN and Adaptive. (Icon selection) Core Aligns the left and right fibers by the center of their cores. Diameter Aligns the left and right fibers by their outer diameters. AIAS Signifies Automatic Intentional Axis Shift. High core-cladding eccentricities have an effect on surface tension during arc, yielding high splice loss. This method is used to intentionally offset the left and right fiber centers in order to minimize this effect. Note: If AIAS is selected, arc parameters cannot be changed. ATTN Signifies Attenuation. Fibers are spliced by shifting the centers of the left and right fiber cores to achieve intentional high splice losses. Before ATTN splice, set the target attenuation (splice loss) and the adjustment factor. Change the adjustment factor so that a yielded splice loss matches the target attenuation.. Adaptive is the alignment method mainly for BIF. It is used in splicing optical fiber with complicated core profiles. <Est. Loss Limit> If the higher estimated splice loss than this value is measured, the splicer warns on the screen. (Numerical input) <Clv. Angle Limit> If the larger cleave angle than this value is measured, the splicer warns on the screen. (Numerical input) 4/5 <HDCM> Monitors and inspects fiber core with high precision. You can select ON or OFF. Normally ON is desirable. OFF is set for specialty fiber splicing. (Icon selection) <Splice ID Name> Each splice condition name can be changed from the initial factory setting to a name that is more meaningful to the user. Please refer to page 7 regarding how to change the splice ID name. (Text input) <Fiber Detection> Automatic fiber detection function. ON/OFF (Icon selection) Please refer to page 8. 5/5 <Arc image Compensation> This function compensates arc power to an optimum level for the arc condition. Set "Arc Environment Compensation" to ON to enable this function. (Icon selection) <Arc Environment Compensation> This function compensates arc power to an optimum level for the environmental condition. (Icon selection) 3

6 Page 1/2 2/2 Heater Program items in administrator menu <Heat Up Temp. A> Heating element rise up to the set temperature in the first term of heating cycle. (Numerical input) <Heating Duration A> Duration of the first term of heating cycle. (Numerical input) <Heat Up Temp. B> Heating element rise up to the set temperature in the middle term of heating cycle. (Numerical input) <Heating Duration B> Duration of the middle term of heating cycle. (Numerical input) <Heat Finish Temp> The temperature of finishing heating cycle after cooling by the fan. (Numerical input) <Sleeve ID Name> Change the protection sleeve. (Text input) <Heat ID Name> Change the heater program s name. (Text input) 4

7 Changing settings Example 1: Change Align Method from Core to Diameter. Fusion Time Prefusion Time sec sec Splice Select Align Method Automatic Core 1/5 Arc Gap um 3/5 Est. Loss Limit db Over Lap um Clv. Angle Limit deg 1: Referring to page 1, go to the administrator menu. Referring to page 4-6 of operation manual, go to the splice program setting screen. 2: Go to the page 3 by using the move ( ), select Align Method to go to the setting screen. Align Method Core Diameter 1/2 SMF AIAS Quick SMF ATTN Quick 3/5 Splice Select Align Method Automatic Diameter Est. Loss Limit db Clv. Angle Limit deg 3: Touch Diameter once. The icon will change its color. Then touch it again to determine selection. 4: Diameter is selected. 5

8 Example 2: Change Arc Center. (Numerical input) 1/5 Fusion Time Prefusion Time Arc Gap sec sec um 2/5 Arc Power Staying Time 0300 step sec Fiber Pulling sec Over Lap um Arc Center Standard dot 1: Referring to page 1, go to the administrator menu. Referring to page 4-6 of operation manual, go to the splice program setting screen unit: dot Max.: Min.: Standard: Arc Center Set Value OK 3: Input the value by touching number keys, then touch OK ( OK ). 2: Go to the page 2 by using the move ( ), select Arc Center to go to the setting screen. 2/5 Arc Power Staying Time 0300 step Fiber Pulling sec Arc Center sec Standard dot 4: Arc Center value is changed. 6

9 Example 3: Edit splice ID name. Fusion Time Prefusion Time sec sec HDCM Splice ID Name ON 1/4 Arc Gap um 4/4 Fiber Ditection ON Over Lap um 1: Referring to page 1, go to the administrator menu. Referring to page 4-6 of operation manual, go to the splice program setting screen. 2: Go to the page 4 by using the move ( ), select Splice ID Name to go to the setting # $ % ^ & * ( ) < >? : { } _ + Q W E R T Y U I O P A S D F G H J K L Shift ,. / ; [ ] - = q w e r t y u i o p a s d f g h j k l Z X C V B N M z x c v b n m Shift Default BS Cancel OK Shift Default BS Cancel OK 3: Edit the name according to the key guidance shown on the screen. 4: After the edit, touch OK. 7

10 Analyzing fiber type APDS: Auto fiber profiling check and Detection System The splicer automatically analyzes optical fiber type to be spliced from fiber image, compares the analyzed splice program to the selected splice program and displays the result on a screen. This system prevents splice program and fiber type from being miss-selected. When the analyzed fiber type is different from the set fiber type, the result screen appears and the splicer stops. Fiber types that can be analyzed are typically SMF, MMF, DSF/NZDS and BIF. The right and left fibers are analyzed individually. If a fiber profile cannot be identified, the splicer displays OTHER. Note: The TYPE-81C fusion splicer stores the profiling information of representative fiber types. Therefore the splicer could make miss-analysis on a different manufacturer s or new fiber types. With regard to profiling data customization and the modification of fiber types, contact our maintenance service center or sales personnel. Reset Fiber Detection Reset Fiber Detection Splicer recommends the change of splice Go on Next (ARC TEST) 1/2 program and starts the ARC TEST [ SMF ] -> [ MMF ] 2/2 Go on SMF Next Quick (SPLICE) SMF Override Quick 003 Fiber Detection Result L:MMF R:MMF Go on Next (ARC TEST) Change the splice program and perform an arc test. Go on Next (Splice) Change the splice program and perform splice. Override Ignore the result and continue to perform the splicing process. Registration of splice program Not all splice programs are registered in the initial factory settings. If you would like to use some other splice programs, you can register in the Administrator menu. Tips The background of the splice program that is registered is shown in blue and highlighted in green when selected. The background of the splice program that is NOT registered is shown in black and the text is highlighted in red when selected. 8

11 MENU 60mm 0.25 X/Y Ready 1/5 NZ G655 Typ. NZ G655 Typ. PureGuide DISP PureMetro 018 Start Select splice program 1: is currently selected. Go to splice program setting screen. In this example, category of NZDS is selected. No.016 NZ G655 Typ. Edit Copy 1/1 Memory 2: Select the splice program with black background you would like to register. The selected splice program is highlighted in red. Then touch the setting icon ( ). No.016 NZ G655 Typ. ON OFF 1/1 3: Select Memory. 4: Select ON to register the splice program. NZ G655 Typ. NZ G655 Typ. 1/5 PureGuide PureMetro Select splice program 5: The black background turns blue. The splice program is registered and can be shown on the operator menu screen as well. The registered splice program is stored after the power is turned off. 9

12 Release of splice program The registered splice program that is currently selected cannot be released. Select other splice program first and release the registered program. MENU X/Y 60mm 0.25 This splice program is currently selected but you would like to release it MENU X/Y NZ G655 Typ. 60mm 0.25 Ready Ready DISP DISP Start Start 1: Referring the page 4-1 of operation manual, select other fiber type first. No.002 ON 002 OFF SM G652 Quick 003 1/1 1/67 SM G652 AIAS 004 PureMetro-SM 028 Select splice program 2: Referring to the page 9, select OFF in the splice program Entry screen to release the splice program. 3: The splice program SMF Standard is released. Tips An administrator can also register a heater program, change settings and edit sleeve names in the same way. Go to the administrator menu, refer to page 4-6 of operation manual, and go to the splice program setting screen. Then refer to page 5 to 7. 10

13 Security (Startup password protection) Using a startup password, Security function prevents unwanted users from accessing the splicer. It is located in Security function on menu screen. Menu January 2011 DATA OK S M T W T F S 1 Touch Security ( ) in MENU screen to go to security screen. 1/1 Splice Data USB Security Security Change Startup Password Cycle Function Login Maintenance Information 2011/01/01 00:00 Security [Disable] [OFF] Please specify the day when the startup password is demanded on the calendar. Touch an arbitrary date on the screen, then touch "OK". A past date cannot be set. Touch the month icon ( January ) or the year icon ( 2011 ) to change the calendar. The calendar is changed by "Move" (, ). Select the item Security, and select the item Enable in the next screen. 1/1 Password Entry Request(yy/mm/dd) [11/01/20] Every Day Every Week Every Month OFF 1234 Enter the startup password Q W E R T Y U I O P BS A S D F G H J K L Z X C V B N M OK Setting startup password screen is displayed. Please set an arbitrary password of four digits. ex) 1234 By selecting Cycle, the setting that demands the startup password for each certain period (every day/every week/every month) after the date when the startup password demand can be done. It becomes impossible to start when the start up password is forgotten. Please note it. Please inquire of our maintenance service center when you forget the startup password by any chance. 11

14 Revision C Jan. 8, 2013 For any inquires and supports, please contact a local agent/distributor. Local agent/distributor details: Tokyo (JAPAN) Sumitomo Electric Industries, Ltd. (Global Business Dept.) Akasaka Center Building, , Motoakasaka, Minato-ku, Tokyo , JAPAN Tel: +81 (0) North Carolina (U.S.A) Sumitomo Electric Lightwave Corp. 78 Alexander Drive, P.O. Box 13445, Research Triangle park, NC27709 U.S.A Toll Free No Tel: London (U.K) Sumitomo Electric Europe Ltd. 220 Centennial Park, Centennial Avenue, Elstree, Herts, WD6 3SL, U.K. Tel: +44 (0) Hong Kong (China) Sumitomo Electric Asia, Ltd. Tel: Shenzhen (China) SUMIDEN ASIA (SHENZHEN) Co.,Ltd. Tel: Beijing (China) SUMIDEN ASIA (SHENZHEN) Co.,Ltd. (Beijing Branch) Tel: Shanghai (China) SUMIDEN ASIA (SHENZHEN) Co.,Ltd. (Shanghai Branch) Tel: Wuhan (China) SUMIDEN ASIA (SHENZHEN) Co.,Ltd. (Wuhan Branch) Tel: Bangkok (Thailand) Sumitomo Electric (Thailand) Limited Tel: +66 (0) to 5 Singapore Sumitomo Electric Interconnect Products (Singapore) Pte.,Ltd. Tel: Dubai (U.A.E.) Middle East office Tel: to 7341 Gurgaon (India) SEI Trading India Pvt. Ltd. (SETI) Tel: Manila (Philippines) SEI (PHILIPPINES) INCORPORATED Tel: / SUMITOMO ELECTRIC INDUSTRIES, LTD. 12