Figure 1. IMPORTANT: The TSC Control will only function with one of the following Steamist Generator models: TSG-7, TSG-10 or TSG-15 steam generators.

Transcription

1 C US LISTED 995C Steambath Control Control Features Total Sense Digital Control 1 Set Point: Indicates steamroom setpoint temperature 2 Temperature Display: Indicates ambient room temperature 3 ON/OFF Keypad: Press keypad to start the system as a guest user Press the Keypad any time the system is on to turn it off 4 Navigation Keys: UP/Down Arrows, Menu, and Select 6 03 : 38 : STEAM F 5 User 1 / User 2: Press to select Pre-Set user settings 6 Clock: Displays current time 5 7 Duration: Remaining time of the system cycle IMPORTANT: Control must be installed inside the steam- room for proper operation of the system Cleaning Instructions: Use a damp cloth and mild soap Do NOT use abrasive cleaners which might scratch the surface or the base of the control SELECT MENU 3 1 Pre-Installation - Control Location The TSC Control must be installed inside the steam- room For convenience the recommended height from the floor is four feet Provide a 1½" hole in the wall at this location (see Figure 1) Figure 1 IMPORTANT: Run the Control Cable through a ¾ conduit To Steam Generator IMPORTANT: Multi-conductor cable must be installed so that the end will not be buried inside the wall The unit will not operate unless the control is installed Coupler 2 Electrical Rough-in Remove the multi-conductor cable from the control packing box Carefully route the multi-conductor control cable from the steam generator to the TSC located inside the steamroom (see Figure 1) Route multi-conductor cable through a ¾" conduit to protect the cable from damage and to facilitate replacement if necessary 1½ Hole located four feet from the floor Double-Sided Adhesive Pad! WARNING: Elderly persons, pregnant women, or those suffering from heart disease, high blood pressure, diabetes, or who are otherwise not in good health, do not use this device unless directed to do so by a physician Also, do not use steambath while under the influence of alcohol IMPORTANT: The TSC Control will only function with one of the following Steamist Generator models: TSG-7, TSG-10 or TSG-15 steam generators 02/09 Pub No 202-A - 1 -

2 C L E A R N e t 1 / 2 F L O I t e o M A D E I S A 3 Control and Cable Installation a) Locate the previously installed cable and black plastic strain relief clamp which is in the control packing box Locate the knockout on the steam generator for the control cable (see Figure 1) b) Place strain relief around cable about seven inches from the end and insert into the hole Remove the protective covering labeled Remove Before Installation from the modular jack found on the PC board c) Remove the protective cap from the multi-conductor cable plug Connect the cable to the modular jack d) Close and secure generator cover e) Locate Telco Jack at female coupler, on back of the TSC control Remove the protective covering labeled Remove Before Installation Remove protective cap from cable and plug into jack Check that the orientation of the plug properly aligns with the jack A snap will indicate the plug is installed correctly (see Figure 2) Figure 3 Figure 4 Adhesive Liner Coupler Control Cable to Generator WARNING: Test the control for operation before continuing on to the next step N U m N Z S I L I C O N E f) Peel adhesive liner from back of the control Apply the control to the wall Press firmly and hold for a few seconds g) After the control is in place, apply silicone (supplied) around the control to form a watertight seal IMPORTANT: The adhesive on the back of the TSC control will NOT seal this control It is the responsibility of the installer to seal this control to the wall with the supplied silicone Water damage to the control is not covered by the warranty Figure 2 - Cable Installation on Steam Generator ¾" Conduit To Control Knockouts for Strain Relief Clamps Relay Board Power Board Fuses Ground Connection Modular Jacks: All four modular jacks are identical and will work in any combination Connect into any jack 02/09 Pub No 202-A - 2 -

3 for Steamhead & Center Hub Figure 6 - Center Hub Installation 1 Make sure the 3/4" nipple protrudes beyond the tile approximately 1/2" (see Figure 5) 2 Wrap the nipple with pipe sealant tape 3 Put a bead of silicone around the outer edge of the Back Plate (see Figure 5) and center the Back Plate over the pipe in an upright position While holding it in place screw the Center Hub onto the nipple, using a ⅜" Hex Key to tighten 4 The Center Hub MUST be aligned with the four walls in the vertical and horizontal position (see Figure 6) Make sure the steamhead O-ring is fully seated into the Back Plate If the nipple is sticking out too far the O-ring will not make a proper seal and the nipple must be adjusted 5 Apply a small amount of silicone at the back center point of the Cover Plate This will aid in preventing movement of this plate (see Figure 6) 6 Place the Cover Plate over the Center Hub This is accomplished by first hooking the top and then snapping the bottom into place 7 Adjust the Back Plate and Cover Plate to line up squarely, and clean excess silicone with rubbing alcohol Figure 5 - Steamhead Installation Apply a small amount of silicone to prevent movement IMPORTANT: Install top first MUST be vertical After inserting the top, snap in the bottom 3/4" NPT (Brass Pipe) Must use sealant tape 1/2" Aromatherapy Reservoir Apply silicone around the back edge of Back Plate to seal and prevent movement O-Ring MUST seal to inside of the Back Plate Apply silicone around the steam pipe to form a watertight seal 3/8" Hex Key Hole Cover Plate Back Plate Center Hub 02/09 Pub No 202-A - 3 -

4 1 2 MENU The Total Sense Control (TSC) has a built in temperature sensor and therefore requires the TSC control to be installed inside the steam room Max Temperature setting: 120 F Max Time setting: 60 Minutes Figure 7 - Installation Suggestions Required Inside Installation TSC Control Locate away from the direct line of shower spray and do NOT locate above steamhead Steamhead Installation Steamhead should be mounted 18" above the finished floor or 6" above the rim of the tub as far from the bather as possible All Instructions must be given to the homeowner for future use East Coast Office: 25 E Union Ave, East Rutherford, NJ Tel: Fax: West Coast Office: 315 W Pondera St, Suite F, Lancaster, CA Tel: Fax: /09 Pub No 202-A - 4 -

5 Programming and Operating Instructions C US Operation! WARNING: Elderly persons, pregnant women, or those suffering from heart disease, high blood pressure, diabetes, or who are otherwise not in good health, do not use this device unless directed to do so by a physician Also, do not use steambath while under the influence of alcohol Figure 1: Total Sense Digital Control Cycle Timer Clock Temperature Setting Temperature Setting Audio Input Selected Dual function keys are used to start user 1 or 2 programs and to skip forward or backward on the ipod playlist Menu navigation keys 03 : 38 : STEAM 112 ipod 110 F 1 2 SELECT MENU Room Temperature User 2 indicator shown, one icon indicates user 1 and no icon indicates the guest Power ON/OFF button and Guest Setting The Total Sense Control (TSC) has a built in temperature sensor and therefore MUST be installed inside the steam room Operation Programming the User Settings To program User 1, press the user 1 select button The display will show the User one icon It will also show the steam bath temperature settings, as shown in Figure 2 In the steam mode the set temperature is easily adjusted with the Up and Down arrows (Figure 2) Figure 2 03 : 38 : Figure 3 03 : 38 : Press the Select button and the remaining cycle time is shown The time may be adjusted up or down from 0-60 minutes Adjusting the time in this window only alters the current cycle (Figure 3) STEAM F STEAM 112 :59 Remaining Cycle Time User 1 Icon 02/08 Pub No 207-A - 1 -

6 Programming and Operating Instructions Operation To adjust the default cycle time, press and hold the MENU button until the setup window is displayed This displays the system setting discussed later in this document and also is where the default timer is changed (Figure 4) Figure 4 Total Sense Control Figure 7 AudioSense VOLUME BASS TREBLE BALANCE MUSIC B INPUT Figure 5 Cycle Timer System Settings Control Settings With the CYCLE TIMER highlighted, Press select Use the arrow Up or Down buttons to adjust the default time cycle for that current user (Figure 5) Cycle Timer (mins) 60 Press the MENU button to return to the previous AudioSense Mode Press the MENU again to switch to ChromaSense mode While in the ChromaSense mode, use the select button to toggle between the different ChromaSense mood lights Use the arrow keys to adjust the light intensity (Figure 8) Figure 8 03 : 38 : ChromoSense 70 F WHITE Press the MENU button to back out of the current display which will bring you back to the TOTAL SENSE CONTROL screen, Press the MENU button again to return to the USER 1 STEAM screen Press the MENU button a third time and if the AudioSense option is installed the display will show the AudioSense Mode In this mode pressing the Up or Down arrows changes the volume The bottom of the display shows the selected audio input (Figure 6) Figure 6 03 : 38 : AudioSense VOLUME MUSIC B 70 F Pressing the SELECT button while in AudioSense mode, gives you more options to adjust you music settings Press the select button again until the setting you want to adjust is highlighted Then use the Up or Down arrow buttons to adjust that setting High light INPUT to select between ipod, Music A and Music B Music A is the 35 mm phone jack input on the left side of the TSC control module Music B is the RCA jacks on the side of the TSC control module (Figure 7) Press the MENU button to toggle the AromaSense mode The selected pump either 1 or 2 is shown To change the selected pump, press the select button Pressing the select button toggles between pump 1 and 2 To adjust the intensity of the oil press the Up or Down button The lowest ON setting is slightly less than one drop per minute and the highest setting is about 5 drops per minute To turn the selected pump off press the down button until the word OFF is displayed (Figure 9) Figure 9 03 : 38 : AromaSense PUMP 2 Off 70 F Press the MENU button again to return to the Steam mode This completes all the user settings for User 1 To set up USER 2 press the power OFF button to turn the power off Then press USER 2 and repeat the above steps for the custom settings for User 2 NOTE: 2 user icons will be shown in the display The guest setting which is selected by pressing the power button when the control is off and indicated by no user icons in the display programs the same as User 1 and 2 The guest setting works as a third user setting 02/08 Pub No 207-A - 2 -

7 Programming and Operating Instructions Programming the System Settings Programming the System Settings Power on TSC control by pressing either USER 1, USER 2 or the power button Press and hold the MENU button to enter the setup window You will see the Cycle timer that was programmed earlier and the "System Settings" Highlight "System Settings" using the Up or Down arrows and press select (Figure 10) Figure 10 Figure 12 AudioSense Input MUSIC A MUSIC B ipod Total Sense Control Cycle Timer System Settings Control Settings Press MENU to return to the previous display The next system setting is Temperature Fahrenheit or Celsius setting Select this setting and change between the F and C with the Up or Down arrows (Figure 13) Figure 13 The first system setting is INSTAMIST This selects the instant on feature which keep the water hot and ready for your next steam bath This feature uses an average of 60 watts of electricity to keep the water hot If the steam bath is not used for long periods of time you may prefer to turn this setting off When this feature is turned on you may hear a slight rumbling sound occasionally as the heater is periodically cycled on for a few seconds With Instamist highlighted in the display press select The INSTAMIST is turned on and off with the Up or Down arrows (Figure 11) Figure 11 Temperature Units F Press MENU to return to the previous display The next system setting is Restore Defaults setting This setting is intended to return the control to the factory setting Select this setting and change between yes and no with the arrow Up or Down arrows If yes is selected the defaults will be restored when the Menu button is pressed after yes is selected (Figure 14) Figure 14 InstaMist Off Press MENU to return to the previous display The next system setting is AudioSense Input Highlight AudioSense and press select This setting allows you to further adjust the volume based on the input level of the audio source connected to the TSC Control Module Use the SELECT button to toggle between the three input choices These settings should start at the lowest settings Use the arrow Up or Down buttons to increase or decrease the input volume boost The ipod setting should be set at the lowest setting Depending on the audio source connected to the Music A and B you may need to increase the input boost to get a more acceptable volume level This is a global setting for all users After making changes to these settings you will need to re adjust the volume for each user (Figure 12) Figure 15 Restore Defaults NO Press MENU to return to the previous display The next system setting is Connected Devices Selecting this displays a list of the connected devices This is used for troubleshooting purposes to determine if all the devices are properly connected and communicating with the control (Figure 15) Gen 1 YES Gen 3 NO AudioSense ChromoSense AromaSense Outside Control Wireless Remote Gen 2 Gen 4 NO NO v10 v10 v10 NO NO 02/08 Pub No 207-A - 3 -

8 Programming and Operating Instructions Programming the Control Settings Press the MENU button twice to enter the setup window Highlight Control Settings and press the select button (Figure 16) Figure 16 Press MENU to return to the previous display The next control setting is the display contrast If necessary this setting adjusts the contrast for optimum viewing With the LCD Contrast highlighted press select and use the arrow buttons Up or Down to adjust the contrast (Figure 20) Total Sense Control Cycle Timer System Settings Control Settings Figure 20 LCD CONTRAST Set Time is already highlighted press the select button to change the time (Figure 17) Figure 17 Total Sense Control Set Time Clock Display Display Contrast Display Backlight Keypad Backlight Press MENU to return to the previous display The next control setting is the LCD Display Backlight adjustment If desired to adjust the LCD backlight, highlight this selection and press select Use the arrow buttons Up or Down to adjust the Backlight (Figure 21) Figure 21 Change the hour with the Up or Down arrow Press SELECT to toggle between hours and minutes Use the arrow buttons to change the minutes The clock will keep time even with a brief power interruption of less than a day (Figure 18) LCD BACKLIGHT Figure 18 03:14 Press MENU to return to the previous display The next control setting is the Keypad Backlight adjustment If desired to adjust the Keypad backlight, highlight this selection and press select Use the arrow buttons Up or Down to adjust the backlight (Figure 22) Figure 22 Press MENU to return to the previous display The next control setting is the clock display This setting turns the clock function on or off With the clock display highlighted press select and use the arrow buttons Up or Down to turn the clock function on or off (Figure 19) Figure 19 KEY LIGHTING Press the power button to exit and turn off Clock Display ON East Coast Office: 25 E Union Ave, East Rutherford, NJ Tel: Fax: West Coast Office: 315 W Pondera St, Suite F, Lancaster, CA Tel: Fax: /08 Pub No 207-A - 4 -

9 Specifications Steambath Control Product Information TSC TSC 5-years parts warranty Programmable Time and Temperature Operates AromaSense, AudioSense and ChromaSense options 03 : 38 : Digital display of ambient and set temperature Icons for system status - heating and set temp STEAM F Dimensions: 4" x 5⅝" Package Includes: Control, 25-Ft Multi-Conductor Cable, 6-Pin Coupler, Steamhead (Delivers 360-Degree Steam Dispersion), Strain Relief Clamp, Silicone Sealant, Installation and Operating Instructions 5⅝" 1 2 SELECT MENU Required Electrical Service: Low-voltage connection from TSG generator via multi-conductor cable (supplied) 4" Notes Installation Notes: Package Contents Surface Mount - 1½" hole required Mounts inside the steam room Steamist recommends that the multi-conductor cable be run through ¾" conduit to protect cable from damage and to facilitate easy replacement Strain Relief Clamp MADE IN USA Net 1/2 FL OZ Item No CLEAR SILICONE Mount control near seating area and not above steamhead Rough-in Notes: Silicone Sealant Control should be mounted 48" above the floor Steamhead to be mounted 18" above the finished floor or 6" above the rim of the tub and as far from the seating area as possible 6-Pin Coupler Product No - Finishes: TSC-PC - Polished Chrome TSC-PN - Polished Nickel TSC-BN - Brushed Nickel TSC-AB - Antique Brass TSC-PB - Polished Brass TSC-PG - Polished 24K Gold TSC-ORB - Oil-Rubbed Bronze 360-Degree Diffusing Steamhead 25-Ft Multi-Conductor Cable 02/ Pub No 214-A

10 03 : 38 : STEAM 110 F MENU START 1 STOP START 2 Specifications Wiring Layout Standard Speaker Wire Control Cable Special Light Cable Standard Speaker Wire 120V 120V CONTROL CABLE CONTROL CABLE TSC Digital Control Module Aroma Box Control Cable Category 5 Cable Tube Tube Wireless Receiver ipod Cradle Aroma Injection Tee TSS-CL Classic Speaker TSC Control TSS-CL Invisible Speakers TSR Remote Control East Coast Office: 25 E Union Ave, East Rutherford, NJ Tel: Fax: West Coast Office: 315 W Pondera St, Suite F, Lancaster, CA Tel: Fax: / Pub No 214-A