FORTINI F4 OSD REV.3

Transcription

1 FORTINI F4 OSD REV.3 Flight Controller USER MANUAL VERSION 1.0 Please contact us if you need further assistance: Tech support: Sales support: Website:

2 1 CONTENTS Features... 2 Pinouts... 2 Dimensions... 2 Connections... 3 Connect with Receivers... 3 FrSky XSR Rx:... 3 FrSky R-XSR Micro Rx:... 5 TBS Crossfire Micro Rx V2:... 7 TBS Crossfire Nano Rx:... 8 Connect with Video Transmitters... 9 Stealth Race VTx:... 9 Stealth Long Range VTx: Using Tramp HV VTx: Using TBS Unify Pro 5G8 VTx: Using TBS Unify Pro Nano 5G8 VTx: Connect With Camera Connect With GPS Connect With Bluetooth Connect with ESC 4 in Hobbywing XRotor Micro 40A 4in1: Hobbywing XRotor Micro 45A 4in1: Cicada 35x4 35A: T-Motor F 35A 4IN1-4S: Tips Guideline configuration OSD with BetaFlight How to open camera setting by Transmitter How to open Betaflight OSD by Transmitter VTx configuration by Transmitter PIDs tunning on Betaflight OSD... 24

3 2 Features Built-in OSD Built-in Camera OSD Control for FPV camera Built-in capacitor 100nF for FOXEER camera Add TX3 for F.Port protocol Dual camera control and LED Strip port Silicone damper for better anti-vibration Fortini F4 OSD modifies camera settings by transmitter 6 UARTs for USB, SBUS, SPORT, TBS Receiver or GPS,Bluetooth,Telemetry VTX Separate power supply for gyro with LDO low noise and high accuracy Built-in driver inverter for S-Bus and Smart-Port connection directly to FC Inrush voltage protection input and output by transient voltage suppressor Invensense gyro for high speed 32khz, lowest noise floor and highest sensitivity Pinouts Dimensions

4 3 Connections *WARNING: FC can support up to 6S Lipo battery and make sure the other devices also support it. Connect with Receivers FrSky XSR Rx: Note: If telemetry of XSR is not working with FC, please update firmware for Rx Using with SBUS protocol

5 4 Using with F.Port protocol *Note: Make sure your Rx is running F.Port protocol firmware

6 5 FrSky R-XSR Micro Rx: Note: If telemetry of R-XSR is not working with FC, please update firmware for Rx Using with SBUS protocol

7 6 Using with F.Port protocol *Note: Make sure your Rx is running F.Port protocol firmware

8 7 TBS Crossfire Micro Rx V2:

9 8 TBS Crossfire Nano Rx:

10 9 Connect with Video Transmitters Stealth Race 5.8GHz VTx: Using 5V from VTx to power Camera Using Battery from VTx to power Camera

11 10 Stealth Long Range 5.8GHz VTx: Using 5V from VTx to power Camera Using Battery from VTx to power Camera

12 11 Using Tramp HV VTx: Using 5V from VTx to power Camera Using Battery from VTx to power Camera

13 12 Using TBS Unify Pro 5G8 VTx: Using 5V from VTx to power Camera Using Battery from VTx to power Camera

14 13 Using TBS Unify Pro Nano 5G8 VTx: Using 5V from VTx to power Camera Using Battery from VTx to power Camera

15 14 Connect With Camera Using with RunCam Using with FOXEER (Arrow Mini, Arrow Micro, Monster)

16 15 Connect With GPS

17 16 Connect With Bluetooth How to use Speedy Bee App Step 1: Open Speedy Bee App. Step 2: Tap to start scanning. Step 3: Select the Bluetooth name. Step 4: Configure the Flight Controller.

18 17 Connect with ESC 4 in 1 *WARNING: FC can support up to 6S Lipo battery and make sure the other devices also support it. Hobbywing XRotor Micro 40A 4in1:

19 18 Hobbywing XRotor Micro 45A 4in1:

20 19 Cicada 35x4 35A:

21 20 T-Motor F 35A 4IN1-4S:

22 21 Tips How to flash firmware for Fortini F4 OSD REV.3 Step 1: Hold Boot button on FC and plug into PC via USB cable to go into DFU mode Step 2: Turn on Full chip erase Step 3: Select target FF_FORTINIF4_REV03 (NOT FF_FORTINIF4) Step 4: Choose new FW version for Flight Controller Step 5: Click Load Firmware [Online] to download FW Step 6: Click Flash Firmware to flash FW for Flight Controller Guideline configuration OSD with BetaFlight Step 1: Connect FC with computer via USB cable. Step 2: Open Betaflight Configurator.

23 22 Step 3: Click Connect on Betaflight interface then go to OSD tab. Step 4: After configuring OSD please click Save to save your configuration. How to open camera setting by Transmitter Stick command: THROTTLE MIDDLE YAW RIGHT PITCH MIDDLE ROLL MIDDLE To navigate through menu: PITCH/ROLL sticks are used to navigate YAW stick is used to adjust / change values

24 23 How to open Betaflight OSD by Transmitter Stick command: THROTTLE MIDDLE + YAW LEFT + PITCH FULL + ROLL MIDDLE To navigate through menu: PITCH/ROLL sticks are used to navigate YAW stick is used to adjust / change values VTx configuration by Transmitter From Betaflight OSD menu use stick go to: Main menu > Features

25 24 Select SA if using TBS Unify Pro VTx Select TR if using Stealth Long Range VTx or Tramp HV VTx STEALTH LONG RANGE VTX TRAMP HV VTX PIDs tunning on Betaflight OSD From Betaflight OSD menu use stick go to: Main menu > Profile > PID

26 25 Thanks for using our product