A B C D REV 1 SHEET 1 OF 1 1 G NO assy_011 DW TITLE SIZE C SCALE 9/17/2016 N 2 2 FG APPROVED CHECKED QA M Henri DRAW PHALANX A B C D

Transcription

1 4 A BPHALANX

2

3 Greetings and good fortune be on you as you have aquired your new greatness. As you work through the assembly passages, please, READ THE DIRECTIONS! There are fine points covered that you will miss if you only assemble by the images on these pages. You will enjoy your journey much more if you read the wisdom provided in this manual. We are sworn to advancement of your drone flying experience and if you have thoughts, suggestions, concerns, or want to share a victorious flight, please feel free to contact us! info@teamaxios.com DISCLAIMER: Team Axios can not foresee the equipment you will purchase or how you will use the product when you receive it. We are not responsible for any injuries or property damage to anyone or anything as it relates to this product. USE AT YOUR OWN RISK!

4

5 D Included with this kit Required to fly M3x10 M3x8 M3x6 M3x6 M2x20 M2x6 M2x10 Bottom plate Top plate Transmitter and reciever (4 channel minimum) Flight controller (FC) Power Distributtion board (BDB) Electronic Spead Controllers (ESC) Brushless motors (We recommend kv or better) Battery (We recommend a 4S battery pack or better) Propellers (We recommend 3 racing propellers or comperable) M3 x 10 Screw M3 x 8 Screw 25mm Standoff 5mm Standoff 1mm flat fabric washer 6mm Nylon Standoff x 38 x 13 x

6 Tools and hardware we recommend Solder Needle Nosed Pliers Flat-Head Allen Phillips-Head Wrench Screw Drivers Set- Metric Hobby Knife Soldering Iron Solder With Flux Wire Clippers Blue Loctite

7 Tools and hardware we recommend (Continued) FPV Camera Recommended: 32mm board with 28mm hole separation FPV Camera Transmitter FPV Goggles / Monitor FPV Receiver Other considerations Extra plugs of your favorite connectors (for power tail) Foam Mounting Tape

8 Contents Main plate assembly 1 FPV Camera assembly 3 Motor Assembly 4 Upper plate assembly 5 Reciever and Antenna Assembly 6 Battery Strap Assembly 7 Frame Assembly 8 Propeller assembly 9 Ready to fly! 10

9

10 Main plate assembly 25mm Standoff STEP 1 Using M3 screws, secure the 25mm standoff to the main plate. 4 What you need for this step M3 x 10 Screw 5 MM Standoff x13 x13 M3 x 10 Screw D 1 C

11 Main plate assembly (continued) STEP 2 M3 Nylon Nut 4 6mm Standoff Flat Fabric Washer Flight Controller (FC) Power Distribution Board (PDB Find the bag with the nylon parts. Secure the PDB and FC to the main plate as shown in the diagram. What you need for this step M3 x 8 Screw M3 x 8 screw 6 MM standoff Fabric washers M3 nylon nuts PDB FC x 1 x 1 D 2 C

12 A B 4 FPV Camera assembly STEP 3 2mm Screws FPV Camera FPV Camera Mount 2mm Nut Video Transmiter (VTX) Add your favorite FPV Camera to the appropriate mount and secure to the main plate. Secure your VTX to the end of the main plate with double sided secure tape. Connect the Camera to the VTX and PDB (See instructions on your partiular VTX and PDB. What you need for this step FPV Camera Camera Mount Associated hardware VTX x 1 x 1 x 1 3

13 Motor Assembly STEP 4 Secure the your motors with M3 x 5 screws M3 x 5 Screw Brushless Motor What you need for this step M3 x 5 screw Brushless Motor x 16 4

14 Upper plate assembly STEP 5 Reciever (RX) Electronic Speed Control (ESC) Secure your ESC s to the upper frame using either zipties or double sided tape (not supplied). Try to secure your wires with zip-ties or make them short enough to not be loose when assembled. Next, secure your reciever to the upper plate with double sided tape. D What you need for this step ESC RX x 1 4 5

15 Reciever and Antenna Assembly STEP 6 Reciever VTX Antenna Remote Cable Your battery can be secured using a strip of hook and loop tape along with a strap run through the upper plate. You can also connect your favorite VTX antenna via a remote cable. Route your battery strap through the slots on the top plate as shown. What you need for this step 6 VTX antenna Remote cable Reciever x 1 x 1 x 1

16 Battery Strap Assembly 4 3 STEP 7 Hook and Loop Battery Strap Your battery can be secured using a strip of hook and loop tape along with a strap run through the upper plate. Route your battery strap through the slots on the top plate as shown. What you need for this step Hook and Loop x 1 Battery Strap x 1 7

17 Frame Assembly STEP 8 M3 x 10 Screw It s time to connect top to bottom plate. With the M3 x 10 screws, secure the upper plate to the bottom. What you need for this step M3 x 10 x 13 8 D C

18 4 Propeller assembly 3 STEP 9 4 Propeller Lock Nut Once you have verified the direction of the motors and function of the controls. It s time to add your favorite 3 inch propellers to your quad. We recommend using lock-nuts (Not provided) to avoid potential problems with props flying off in flight. What you need for this step Lock Nuts 3 Propellers 9

19 Ready to fly! STEP 10 Now you ve completed your build. Be sure to research your particular equipment and be sure it is 100% operational before attempting to fly. WARNING: NEVER test your motors with the propellers on B A

20 NOTES: 11