HIGH TECH CHIPS, INC. HTC151 LED FLASHER. 1.0 General description.
|
|
|
- Pierce Francis
- 6 years ago
- Views:
Transcription
1 HTC151 LED FLASHER 1.0 General description. This circuit is designed to work as led flasher. LED s sequentially turn on and off according to the part used. D[0:2] inputs are used to control flashing frequency. There are seven different frequencies selectable. See D[0:2] input settings versus frequency table. HTC151 Can control up to 64 LED's (eight LED's per 3mA each). Features Minimum number of external components. Easy selection of alternating frequency. Predictability and design ease. PDIP, SOIC 1 VDD GND 14 2 D0 LED D1 LED D2 LED NU LED LED1 LED4 9 7 LED2 LED3 8 HTC151A, HTC151B Pin out description. Abbreviations used: O - output, I - input, P - power. Pin number Name I / O Description Notes 1 VDD P Power +2.5V to +5.5V 2 D0 I Frequency selector D0 Tie it to VDD or GND(see table below) 3 D1 I Frequency selector D1 Tie it to VDD or GND(see table below) 4 D2 I Frequency selector D2 Tie it to VDD or GND(see table below) 5 NU I Not used Tie it to VDD or GND 6 LED 1 O Output for LED1 Can source up to 25mA 7 LED 2 O Output for LED2 Can source up to 25mA 8 LED 3 O Output for LED3 Can source up to 25mA 9 LED 4 O Output for LED4 Can source up to 25mA 10 LED 5 O Output for LED5 Can source up to 25mA 11 LED 6 O Output for LED6 Can source up to 25mA 12 LED 7 O Output for LED7 Can source up to 25mA 13 LED 8 O Output for LED8 Can source up to 25mA 14 GND P Ground Ground pin Frequency selection per D [0:2] Abbreviations used: 0 connection to GND, 1 connection to VDD. 1 D2 D1 D0 Switching frequency Hz Hz
2 Hz Hz Hz Hz Hz Hz Please note that those values are for reference only. Actual frequency can vary up to 10 percent depending upon VDD voltage and operational temperature. 2.0 Functional description. HTC151 has two variations determined by part number. Common to all models of HTC151 is alternating frequency selection and pin-out. Please refer to Typical connection diagram used as reference. Frequency is changed when state of D [0:2] input pins change. Refer to Frequency selection per D [0:2] table for frequency selection. Note that Dip Switch could be omitted by hard wiring D [0:2] inputs to GND or VDD. This section describes operation of each HTC150 model separately. Each part uses different alternating algorithm. HTC151A States: 1. LED1 is turned on and all others are off. 2. LED2 is turned on and all others are off. 3. LED3 is turned on and all others are off. 4. LED4 is turned on and all others are off. 5. LED5 is turned on and all others are off. 6. LED6 is turned on and all others are off. 7. LED7 is turned on and all others are off. 8. LED8 is turned on and all others are off. State is changed at frequency selected by D [0:2]. HTC151B (Ping-Pong) States: 1. LED1 is turned on and all others are off. 2. LED2 is turned on and all others are off. 3. LED3 is turned on and all others are off. 4. LED4 is turned on and all others are off. 5. LED5 is turned on and all others are off. 6. LED6 is turned on and all others are off. 7. LED7 is turned on and all others are off. 8. LED8 is turned on and all others are off. 9. LED7 is turned on and all others are off. 10. LED6 is turned on and all others are off. 11. LED5 is turned on and all others are off. 12. LED4 is turned on and all others are off. 13. LED3 is turned on and all others are off. 14. LED2 is turned on and all others are off. 2
3 State is changed at frequency selected by D[0:2]. The circuit will change the flashing frequency as soon as DO, D1 or D2 input pin state is changed. From that time next LED's start flashing at new frequency. The first LED starts over with the new frequency and it continues until the D0, D1 or D2 input pin state is changed again. 3.0 Typical connection diagram. VCC C1 R1 R2 R3 0.1 U S1 SW DIP K 10K 10K 1 VDD LED8 13 R4 330 LED7 12 R R LED6 D0 10 R LED5 D1 9 R LED4 D2 8 R9 330 LED3 5 NU LED2 7 R GND LED1 6 R D8 D6 D4 D2 D7 D5 D3 D1 HTC Electrical characteristics. Operational Voltage to +5.5V Current consumption with no load attached 3 ma 1 LEDx output low voltage (5mA load) 0.4V 1 LEDx output low voltage (25mA load) 0.75V 1 LEDx output high voltage (5mA source) VDD-0.7V 1 LEDx output source current max 25mA 1 LEDx output sink current max 25mA 1 NOTES: 1. Those values are characterized but not tested. 3
4 5.0 Ordering information. H T C X X X OPTIONAL: Temperature range: C = 0 o C to +70 o C, I = - 40 o C to + 85 o C. PACKAGE: S 150 mil SOIC D 300 mil PDIP. Model A (sequential), B (Ping-Pong), PART NUMBER. 4
5 6.0 Mechanical information. 14-Lead Plastic Dual In-line (P) 300 mil (PDIP) Units INCHES* MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX Number of Pins n Pitch p Top to Seating Plane A Molded Package Thickness A Base to Seating Plane A Shoulder to Shoulder Width E Molded Package Width E Overall Length D Tip to Seating Plane L Lead Thickness c Upper Lead Width B Lower Lead Width B Overall Row Spacing eb Mold Draft Angle Top α Mold Draft Angle Bottom β *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash protrusions. Mold flash or protrusions shell not exceed.010 (0.254mm)per side. JEDEC Equivalent:MS-001 5
6 14-Lead Plastic Small Outline (SO) Narrow, 150 mil (SOIC) Units INCHES * MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX Number of Pins n Pitch P Overall Height A Molded Package Thickness A Standoff A Overall Width E Molded Package Width E Overall Length D Chamfer Distance h Foot Length L Foot Angle φ Lead Thickness c Lead Width Β Mold Draft Angle Top α Mold Draft Angle Bottom β *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash protrusions. Mold flash or protrusions shell not exceed.010 (0.254mm)per side. JEDEC Equivalent:MS-013 6
7 HTC makes no warranty, express, statutory implied or by description, regarding information set forth herein or regarding the freedom of described devices from patent infringement. HTC makes no warranty or merchantability or fitness for any purposes. HTC reserves right to discontinue production and change specifications and prices at any time and without notice. HTC's products are intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment, are specifically not recommended without additional processing by HTC for such applications. High Tech Chips, Inc. 7
n/a PIC12F629-I/P (RC) n/a PIC12F629-I/SN (RC) n/a PIC12F675-I/P (RC) n/a PIC12F675-I/SN MICROCONTROLLER (RC)
DATA SHEET PIC Microcontrollers Order code Manufacturer code Description 73-36 n/a PICF69-I/P (RC) 73-364 n/a PICF69-I/SN (RC) 73-34 n/a PICF675-I/P (RC) 73-36 n/a PICF675-I/SN MICROCONTROLLER (RC) PIC
24AA16/24LC16B. 16K I 2 C Serial EEPROM. Device Selection Table. Description: Features: Package Types. Block Diagram. Temp. Ranges.
6K I C Serial EEPROM Device Selection Table Part Number Features: Vcc Range Max. Clock Frequency Temp. Ranges A6.7-. 00 khz () I LC6B.-. 00 khz I, E Note : 00 khz for
Remote Control Decoder IC
DESCRIPTION is a remote control decoder paired with PT2260 or PT2262 utilizing CMOS Technology. It has 12-bit of tri-state address pins providing a maximum of 531,441 (or 3 12 ) address codes; thereby
25AA040/25LC040/25C040
Not recommended for new desig Please use AA00A or LC00A. AA00/LC00/C00 K SPI Bus Serial EEPROM Device Selection Table Part Number Features: Low-power CMOS technology: - Write current:, typical - Read current:
XRD87L85 Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter
Low-Voltage CMOS 8-Bit High-Speed Analog-to-Digital Converter April 2002-1 FEATURES 8-Bit Resolution Up to 10 MHz Sampling Rate Internal S/H Function Single Supply: 3.3V VIN DC Range: 0V to V DD VREF DC
XRD8775 CMOS 8-Bit High Speed Analog-to-Digital Converter
CMOS 8-Bit High Speed Analog-to-Digital Converter April 2002-4 FEATURES 8-Bit Resolution Up to 20MHz Sampling Rate Internal S/H Function Single Supply: 5V V IN DC Range: 0V to V DD V REF DC Range: 1V to
24C08/24C16. Two-Wire Serial EEPROM. Preliminary datasheet 8K (1024 X 8)/16K (2048 X 8) General Description. Pin Configuration
Two-Wire Serial EEPROM Preliminary datasheet 8K (1024 X 8)/16K (2048 X 8) Low-voltage Operation 1.8 (VCC = 1.8V to 5.5V) Operating Ambient Temperature: -40 C to +85 C Internally Organized 1024 X 8 (8K),
Electronic Volume Controller IC
DESCRIPTION is an electronic volume controller IC utilizing CMOS Technology specially designed for use on audio equipment. It has 2 built-in channels making it ideally suitable for mono and stereo sound
DESCRIPTION FEATURES APPLICATIONS. Digital Echo/Surround Processor IC PT2396
DESCRIPTION PT2396 is a digital echo/surround processor IC utilizing CMOS Technology. Analog Signal inputted to PT2396 is converted to digital signal by A-D converter and then stored into the internal
I²C-Compatible (Two-Wire) Serial EEPROM 32 Kbit (4,096 x 8)
I²C-Compatible (Two-Wire) Serial EEPROM 32 Kbit (4,096 x 8) AT24C32E Features Low-Voltage Operation: V CC = 1.7V to 3.6V Internally Organized as 4,096 x 8 (32K) Industrial Temperature Range: -40 C to +85
GT24C64 2-WIRE. 64K Bits. Serial EEPROM
GT24C64 2-WIRE 64K Bits Serial EEPROM Copyright 2013 Giantec Semiconductor Inc. (Giantec). All rights reserved. Giantec reserves the right to make changes to this specification and its products at any
Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. APPLICATION NOTE A V A I L A B L E AN61 16K X25160 2K x 8 Bit SPI Serial
+2.5 V Low Power Precision Voltage Reference REF43
+2.5 V Low Power Precision Voltage Reference REF43 FEATURES PIN CONFIGURATION GENERAL DESCRIPTION The REF43 is a low power precision reference providing a stable 2.5 V output independent of variations
ICS548A-03 LOW SKEW CLOCK INVERTER AND DIVIDER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS548A-03 Description The ICS548A-03 is a low cost, low skew, high-performance general purpose clock designed to produce a set of one output clock, one inverted output clock, and one clock divided-by-two.
Two-wire Serial EEPROM AT24C01A AT24C02 AT24C04 AT24C08 (1) AT24C16 (2)
Features Low-voltage and Standard-voltage Operation.7 (V CC =.7V to.v).8 (V CC =.8V to.v) Internally Organized 8 x 8 (K), 6 x 8 (K), x 8 (4K), 04 x 8 (8K) or 048 x 8 (6K) Two-wire Serial Interface Schmitt
64K (8K x 8) Battery-Voltage Parallel EEPROM with Page Write and Software Data Protection AT28BV64B
Features Single 2.7V to 3.6V Supply Hardware and Software Data Protection Low Power Dissipation 15mA Active Current 20µA CMOS Standby Current Fast Read Access Time 200ns Automatic Page Write Operation
TSL250R, TSL251R, TSL252R
TSL250R, TSL251R, TSL252R Light-to-Voltage Optical Sensors General Description The TSL250R, TSL251R, and TSL252R are light-to-voltage optical sensors, each combining a photodiode and a transimpedance amplifier
APR9301 APLUS INTEGRATED CIRCUITS INC. Single-Chip Voice Recording & Playback Device for Single 20 to 30 Second Message. Features
INTEGRATED CIRCUITS I. Features Single-Chip Voice Recording & Playback Device for Single 20 to 30 Second Message Single-chip, high quality voice recording & playback solution - No external ICs required
CD4010C Hex Buffers (Non-Inverting)
Hex Buffers (Non-Inverting) General Description The CD4010C hex buffers are monolithic complementary MOS (CMOS) integrated circuits. The N- and P-channel enhancement mode transistors provide a symmetrical
8-CHANNEL SATURATED SINK DRIVER
Data Sheet 29320B UDNA Developed for use with low-voltage LED and incandescent displays requiring low output saturation voltage, the UDNA and ASLW meet many interface needs, including those exceeding the
GT24C WIRE. 1024K Bits. Serial EEPROM
GT24C1024 2-WIRE 1024K Bits Serial EEPROM Copyright 2013 Giantec Semiconductor Inc. (Giantec). All rights reserved. Giantec reserves the right to make changes to this specification and its products at
FST3257 Quad 2:1 Multiplexer / Demultiplexer Bus Switch
FST3257 Quad 2:1 Multiplexer / Demultiplexer Bus Switch Features 4Ω Switch Connection Between Two Ports Minimal Propagation Delay Through the Switch Low I CC Zero Bounce in Flow-Through Node Control Inputs
I²C-Compatible (Two-Wire) Serial EEPROM 1 Kbit (128 x 8), 2 Kbit (256 x 8)
I²C-Compatible (Two-Wire) Serial EEPROM 1 Kbit (128 x 8), 2 Kbit (256 x 8) Features Low-Voltage Operation: V CC = 1.7V to 3.6V Internally Organized as 128 x 8 (1K) or 256 x 8 (2K) Industrial Temperature
MP1251/MP1252 SMBus Voltage Source
General Description The MP1251 and MP1252 are voltage sources with interfaces. These ICs have a D/A converter that outputs a voltage based on an internal reference. The MP1251 output voltage has 32 voltage
USB Port USB 2.0 Hub Controller PRODUCT FEATURES. Data Brief
USB2502 2-Port USB 2.0 Hub Controller PRODUCT FEATURES Data Brief Integrated USB 2.0 Compatible 2-Port Hub High-Speed (480Mbits/s), Full-Speed (12Mbits/s) and Low-Speed (1.5Mbits/s) compatible Full power
ISSI Preliminary Information January 2006
2K-BIT/4K-BIT SPI SERIAL ELECTRICALLY ERASABLE PROM January 2006 FEATURES Serial Peripheral Interface (SPI) Compatible Supports SPI Modes 0 (0,0) and 3 (1,1) Low-voltage Operation Vcc = 1.8V to 5.5V Low
Distributed by: www.jameco.com -800-83-4242 The content and copyrights of the attached material are the property of its owner. SOLID-STATE HEXADECIMAL DISPLAY WITH INTEGRAL TTL CIRCUIT TO ACCEPT, STORE,
I²C-Compatible (2-Wire) Serial EEPROM 8-Kbit (1,024 x 8)
I²C-Compatible (2-Wire) Serial EEPROM 8-Kbit (1,024 x 8) Features Low-Voltage Operation: Vcc = 1.7V to 3.6V Internally Organized as 1,024 x 8 (8K) Industrial Temperature Range -40 C to +85 C I 2 C-Compatible
74F00 Quad 2-Input NAND Gate
Quad 2-Input NAND Gate General Description This device contains four independent gates, each of which performs the logic NAND function. Ordering Code: December 1994 Revised September 2000 Order Number
Is Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
TLC2543C, TLC2543I, TLC2543M 12-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 ANALOG INPUTS
2-Bit-Resolution A/D Converter 0-µs Conversion Time Over Operating Temperature Analog Input Channels Built-In Self-Test Modes Inherent Sample-and-Hold Function Linearity Error... ± LSB Max On-Chip System
2-wire Serial EEPROM AT24C01A AT24C02 AT24C04 AT24C08 AT24C16
Features Low-voltage and Standard-voltage Operation 5.0 (V CC = 4.5V to 5.5V) 2.7 (V CC = 2.7V to 5.5V) 2.5 (V CC = 2.5V to 5.5V) 1.8 (V CC = 1.8V to 5.5V) Internally Organized 128 x 8 (1K), 256 x 8 (2K),
MX877RTR. 8-Channel, 60V Driver with Push-Pull Output, 3 Wire Interface INTEGRATED CIRCUITS DIVISION. Features. Description.
8-Channel, 6V Driver with Push-Pull Output, 3 Wire Interface Features Eight (8) Outputs Rated at 6V, ±8mA Push-Pull Driver Configuration 6V to 6V Driver Supply Range 2.7V to 5.5V Logic Supply Range 3-Wire
SN54F38, SN74F38 QUADRUPLE 2-INPUT POSITIVE-NAND BUFFERS WITH OPEN-COLLECTOR OUTPUTS
SNF, SN7F SDFS0A MARCH 7 REVISED OCTOBER Package Options Include Plastic Small-Outline Packages, Ceramic Chip Carriers, and Standard Plastic and Ceramic 00-mil DIPs description These devices contain four
MM74HCU04 Hex Inverter
MM74HCU04 Hex Inverter Features Typical propagation delay: 7ns Fanout of 15 LS-TTL loads Quiescent power consumption: 10µA maximum at room temperature Low input current: 1µA maximum General Description
PC POWER SUPPLY SUPERVISOR
` HY510N PC POWER SUPPLY SUPERVISOR Data Sheet REV. 1.30 September 21, 2004 The information in this document is subject to change without notice. 1 11 TEL:886-2-23775117 FAX:886-2-23773189 Email:salesdep@hawyang.com.tw
MM74HC132 Quad 2-Input NAND Schmitt Trigger
MM74HC132 Quad 2-Input NAND Schmitt Trigger Features Typical propagation delay: 12ns Wide power supply range: 2V 6V Low quiescent current: 20µA maximum (74HC Series) Low input current: 1µA maximum Fanout
iw3623 Product Brief AC/DC Digital Power Controller for High Power Factor LED Drivers 1.0 Features 2.0 Description 3.
1.0 Features Isolated AC/DC off-line LED driver Power factor > 0.95 for wide input voltage range 100 277V AC Total harmonic distortion (THD) < 10% Under 5% 100Hz/120Hz output current ripple Resonant control
Features. Applications
ALA ADAT Optical Encoder General Description The ALA OptoGen interface encodes four stereo pairs (8 channels) of digital audio and produces a single data stream suitable for transmission according to the
BL24C02/BL24C04/BL24C08/BL24C16
BL24C02/BL24C04/BL24C08/BL24C16 2K bits (256 X 8) / 4K bits (512 X 8) / 8K bits (1024 X 8) / 16K bits (2048 X 8) Two-wire Serial EEPROM Features Two-wire Serial Interface VCC = 1.8V to 5.5V Bi-directional
2-Wire Serial EEPROM AT24C01. Features. Description. Pin Configurations. 1K (128 x 8)
Features Low Voltage and Standard Voltage Operation 2.7 (V CC = 2.7V to 5.5V) 1.8 (V CC = 1.8V to 5.5V) Internally Organized 128 x 8 2-Wire Serial Interface Bidirectional Data Transfer Protocol 100 khz
1-Megabit (128K x 8) 5-volt Only Flash Memory AT29C010A. Features. Description. Pin Configurations
Features Fast Read Access Time - 70 ns 5-Volt Only Reprogramming Sector Program Operation Single Cycle Reprogram (Erase and Program) 1024 Sectors (128 bytes/sector) Internal Address and Data Latches for
High- Performance Flash PLD ATF16V8B. Features. Block Diagram. Pin Configurations
Features Industry Standard Architecture Emulates Many 20-Pin PALs Low Cost Easy-to-Use Software Tools High-Speed Electrically Erasable Programmable Logic Devices 7.5 ns Maximum Pin-to-Pin Delay Several
DC/DC Converters. TSM Series, 1 Watt. Features. Models
TSM Series, Watt Features SMD package (SOIC-4/8) Construction in lead frame technology Isolated single and dual output I/O isolation 000 VDC High efficiency Operating temperature 40 C to +85 C Reflow solder
ORDERING INFORMATION. Order Numbers: COM20019ILJP for 28 pin PLCC package; COM20019I-DZD for 28 pin PLCC lead-free RoHS Compliant package
COM20019I Cost Competitive ARCNET (ANSI 878.1) Controller with 2K x 8 On-Chip RAM Product Features New Features: Data Rates up to 312.5 Kbps Programmable Reconfiguration Times 28 Pin PLCC and 48 Pin TQFP
Freescale Semiconductor, I
MOTOROLA SEMICONDUCTOR TECHNICAL DATA nc. Order number: Rev 3, 08/2004 3.3 V Zero Delay Buffer The is a 3.3 V Zero Delay Buffer designed to distribute high-speed clocks in PC, workstation, datacom, telecom
LAN bit Non-PCI 10/100 Ethernet Controller with HP Auto-MDIX Support PRODUCT FEATURES. Highlights. Target Applications.
LAN9215 16-bit Non-PCI 10/100 Ethernet Controller with HP Auto-MDIX Support PRODUCT FEATURES Highlights Optimized for medium performance applications Efficient architecture with low CPU overhead Easily
AIC A Dual USB High-Side Power Switch FEATURES DESCRIPTION APPLICATIONS TYPICAL APPLICATION CIRCUIT
1.0A Dual USB High-Side Power Switch FEATURES 2.7V to 6.5V Input Voltage Range 1.0A Dual Continuous Load Current 100mΩ High-Side P-MOSFET Switch 20Ω Open-Drain Over-Current Flag Output 80uA Quiescent Supply
SN54BCT760, SN74BCT760 OCTAL BUFFERS/DRIVERS WITH OPEN-COLLECTOR OUTPUTS
SNBCT0, SNBCT0 SCBS0B JULY REVISED NOVEMBER Open-Collector Version of BCT Open-Collector Outputs Drive Bus Lines or Buffer Memory Address Registers ESD Protection Exceeds 000 V Per MIL-STD-C Method 0 Packages
I²C-Compatible (2-Wire) Serial EEPROM 16 Kbit (2,048 x 8)
I²C-Compatible (2-Wire) Serial EEPROM 16 Kbit (2,048 x 8) Features Low-Voltage Operation: V CC = 1.7V to 5.5V Internally Organized as 2,048 x 8 (16K) Industrial Temperature Range: -40 C to +85 C I 2 C-Compatible
CD4023BC Buffered Triple 3-Input NAND Gate
CD4023BC Buffered Triple 3-Input NAND Gate General Description These triple gates are monolithic complementary MOS (CMOS) integrated circuits constructed with N- and P- channel enhancement mode transistors.
SMS Volt TVS Array For ESD and Latch-Up Protection. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics.
Description The SMS series of TS arrays are designed to protect sensitive electronics from damage or latch-up due to ESD, lightning, and other voltage-induced transient events. Each device will protect
AS5161-EK-AB / AS5162-EK-AB 12 BIT Magnetic Angle Position Sensor
User Manual AS5161 / AS5162 Adapterboard AS5161-EK-AB / AS5162-EK-AB 12 BIT Magnetic Angle Position Sensor www.ams.com Revision 1.0 / 2012/10/31 Table of Contents 1. General Description... 2 2. Package
MLX Features and Benefits Chopper stabilized amplifier stage Micropower consumption for batterypowered
Features and Benefits Chopper stabilized amplifier stage Micropower consumption for batterypowered applications Omnipolar, output switches with absolute value of North or South pole from magnet Operation
Integrated circuit 93C56
Integrated circuit 93C56 Features Low Voltage and Standard Voltage Operation 5.0 (V CC = 4.5V to 5.5V) 2.7 (V CC = 2.7V to 5.5V) 2.5 (V CC = 2.5V to 5.5V) 1.8 (V CC = 1.8V to 5.5V) User Selectable Internal
SN75240 DUAL UNIVERSAL SERIAL BUS PORT TRANSIENT SUPPRESSOR SLLS266 FEBRUARY 1997
DUL UNIVERSL SERIL US PORT TRNSIENT SUPPRESSOR SLLS266 FERURY 997 Design to Protect Submicron 3-V or -V Silicon from Noise Transients pplicable to Two High- or Low-Speed Universal Serial us (US) Host,
RClamp0504F RailClamp Low Capacitance TVS Array
- RailClamp Description RailClamps are surge rated diode arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected
RClamp0504FA RailClamp Low Capacitance TVS Array
- RailClamp Description RailClamp low capacitance TVS array designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected
SPI. 64K Bits. Serial EEPROM
GT25C64 SPI 64K Bits Serial EEPROM Copyright 2011 Giantec Semiconductor Inc. (Giantec). All rights reserved. Giantec reserves the right to make changes to this specification and its products at any time
X K x 8 Bit 64K. 5MHz SPI Serial E 2 PROM with Block Lock TM Protection
64K X25650 5MHz SPI Serial E 2 PROM with Block Lock TM Protection 8K x 8 Bit FEATURES 5MHz Clock Rate Low Power CMOS
STATIC RAM MEMORY ARRAY COLUMN I/O CIRCUITS COLUMN SELECT 3817 FHD F01
1K Bit X22C12 256 x 4 Nonvolatile Static RAM FEATURES High Performance CMOS 150ns RAM Access Time High Reliability Store Cycles: 1,000,000 Data Retention: 100 Years Low Power Consumption Active: 40mA Max.
16-megabit 2.5-volt or 2.7-volt DataFlash AT45DB161D
Features Single 2.5V - 3.6V or 2.7V - 3.6V Supply RapidS Serial Interface: 66 MHz Maximum Clock Frequency SPI Compatible Modes 0 and 3 User Configurable Page Size 512 Bytes per Page 528 Bytes per Page
Two-wire Serial EEPROM AT24C11
Features Low Voltage and Standard Voltage Operation 2.7 (V CC = 2.7V to 5.5V).8 (V CC =.8V to 5.5V) Internally Organized 28 x 8 Two-wire Serial Interface Bidirectional Data Transfer Protocol 400 khz (.8V)
GT24C32A 2-WIRE. 32K Bits. Serial EEPROM
GT24C32A 2-WIRE 32K Bits Serial EEPROM Copyright 2013 Giantec Semiconductor Inc. (Giantec). All rights reserved. Giantec reserves the right to make changes to this specification and its products at any
Industry Standard Architecture Emulates Many 20-pin PALs Low-cost, Easy to Use Software Tools. Advanced Flash Technology Reprogrammable 100% Tested
ATF16V8C High Performance Electrically-Erasable PLD DATASHEET Features Industry Standard Architecture Emulates Many 20-pin PALs Low-cost, Easy to Use Software Tools High Speed Electrically-Erasable Programmable
2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS Description. Features. Block Diagram DATASHEET
DATASHEET 2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS557-08 Description The ICS557-08 is a 2:1 multiplexer chip that allows the user to select one of the two HCSL (Host Clock Signal Level) or LVDS input pairs
IX2204. Dual Low Side IGBT Gate Driver INTEGRATED CIRCUITS DIVISION. Features. Description. Applications. Ordering Information
Features High Output Current: 2A Source/4A Sink Wide Operating Voltage Range: to +26V Negative Gate Drive Capability Desaturation Detection Circuit Separate Source and Sink Outputs Programmable Blanking
TSHARC-C2 Surface Capacitive Touch Screen Microcontroller Application Guide Ver. 3.3
H:\PigData\MasterBinders\03_Products\TSHARC_Chips\TSHARC_C0_Chip\TSHARC_C0_ApplicationManual\TS HARC-C2_Chip_App_Guide3.3B090827.doc TSHARC-C2 Surface Capacitive Touch Screen Microcontroller Application
AT24C01A/02/04/08/16. 2-Wire Serial CMOS E 2 PROM. Features. Description. Pin Configurations. 1K (128 x 8) 2K (256 x 8) 4K (512 x 8) 8K (1024 x 8)
AT24C01A/02/04/08/16 Features Low Voltage and Standard Voltage Operation 5.0 (V CC = 4.5V to 5.5V) 2.7 (V CC = 2.7V to 5.5V) 2.5 (V CC = 2.5V to 5.5V) 1.8 (V CC = 1.8V to 5.5V) Internally Organized 128
MIC1832. General Description. Features. Applications. Typical Application
3.3V Voltage Supervisor with Manual Reset, Watchdog Timer and Dual Reset Outputs General Description The is a low-current microprocessor supervisor for monitoring 3.3V and 3V systems. The device features
A0021. Overview. Features. Ordering Information. HSS Touch Signature IC 6 Input - I 2 C. Part Number Format: A X Y Z
VSS NC NC VDD SDA SENSOR 2 SENSOR 1 ADD1 HSS Touch Signature IC 6 Input - I 2 C A0021 Overview The patented AlSentis A0021 Touch IC is a complete 1 6 input touch sensing solution. It includes all signal
COP472-3 Liquid Crystal Display Controller
COP472-3 Liquid Crystal Display Controller General Description The COP472 3 Liquid Crystal Display (LCD) Controller is a peripheral member of the COPSTM family fabricated using CMOS technology The COP472-3
SENSYLINK Microelectronics Co., LTD. (CT1820S) Single-Wire Digital Temperature Sensor
SENSYLINK Microelectronics (CT1820S) Single-Wire Digital Temperature Sensor CT1820S is a Digital Temperature Sensor with±0.5 C Accuracy over -10 C to 80 C. Single-Wire Digital interface is Compatible with
ST78C34 GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO DESCRIPTION. PLCC Package FEATURES ORDERING INFORMATION
GENERAL PURPOSE PARALLEL PRINTER PORT WITH 83 BYTE FIFO DESCRIPTION The ST78C34 is a monolithic Bidirectional Parallel port designed to operate as a general purpose I/O port. It contains all the necessary
Data sheet acquired from Harris Semiconductor SCHS020C Revised October 2003
Data sheet acquired from Harris Semiconductor SCHS020C Revised October 2003 The CD4009UB and CD4010B types are supplied in 16-lead hermetic dual-in-line ceramic packages (F3A suffix), 16-lead dual-in-line
ISL MMIC Silicon Bipolar Broadband Amplifier. Features. Ordering Information. Applications. Typical Application Circuit
ISL55 Data Sheet August 25, 1 FN258.2 MMIC Silicon Bipolar Broadband Amplifier The ISL55 is a high performance gain block featuring a Darlington configuration using high f T transistors and excellent thermal
SKY : 2.4 GHz Low-Noise Amplifier
DATA SHEET SKY65405-21: 2.4 GHz Low-Noise Amplifier Applications 802.11b/g/n PC cards, NICs, and USB dongles 802.11b/g/n tablets 802.11b/g/n access points, routers, and gateways 2.4 GHz ISM radios V_ENABLE
MAS6240 Piezo Driver with Multi-Mode Charge Pump
MAS624 Piezo Driver with Multi-Mode Charge Pump Both Single Ended and Differential Output Three-Step Volume Adjusting Up to 8Vpp Output from 3V Supply One Wire Audio & Shutdown Control High Efficiency
2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS Features
DATASHEET 2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS557-08 Description The ICS557-08 is a 2:1 multiplexer chip that allows the user to select one of the two HCSL (Host Clock Signal Level) input pairs and
L9966. FlexInput IC for automotive applications. Data brief. Features. Description
Data brief FlexInput IC for automotive applications Features AEC-Q100 qualified 12 V and 24 V systems compatible (operating battery supply voltage 5.5 V-36 V) Programmable interface with 15 total inputs:
SMDA05C-7 THRU SMDA24C-7
Description The SMDAxxC-7 series of transient voltage suppressors are designed to protect components which are connected to data and transmission lines from voltage surges caused by electrostatic discharge
CPC2025NTR. 400V Dual Normally-Open Single-Pole 8-Pin SOIC OptoMOS Relay INTEGRATED CIRCUITS DIVISION
4V Dual Normally-Open Single-Pole 8-Pin SOIC OptoMOS Relay Parameter Rating Units Blocking Voltage 4 V P Current 1 ma rms / ma DC On-Resistance (max) LED Forward Current (to Activate) 2 ma Features V rms
OPTICAL MOUSE SENSOR
OPTICAL MOUSE SENSOR NST TECHNOLOGIES Series Data sheet USB INTERFACE Version 1.50 1. Description is a low-cost CMOS optical sensor SOC for USB optical computer mouse. It provides an all-in-one solution
2-wire Serial EEPROM AT24C512. Preliminary. 2-Wire Serial EEPROM 512K (65,536 x 8) Features. Description. Pin Configurations.
Features Low-voltage and Standard-voltage Operation 5.0 (V CC = 4.5V to 5.5V) 2.7 (V CC = 2.7V to 5.5V) 1.8 (V CC = 1.8V to 3.6V) Internally Organized 65,536 x 8 2-wire Serial Interface Schmitt Triggers,
SN54ALS32, SN54AS32, SN74ALS32, SN74AS32 QUADRUPLE 2-INPUT POSITIVE-OR GATES
Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 00-mil DIPs description These devices contain four independent -input positive-or
256K (32K x 8) Paged Parallel EEPROM AT28C256
Features Fast Read Access Time 150 ns Automatic Page Write Operation Internal Address and Data Latches for 64 Bytes Internal Control Timer Fast Write Cycle Times Page Write Cycle Time: 3 ms or 10 ms Maximum
74VHC132 Quad 2-Input NAND Schmitt Trigger
74VHC132 Quad 2-Input NAND Schmitt Trigger General Description The VHC132 is an advanced high speed CMOS 2-input NAND Schmitt Trigger Gate fabricated with silicon gate CMOS technology. It achieves the
USB2507. Integrated USB 2.0 Compatible 7-Port Hub PRODUCT FEATURES. Data Brief
USB2507 Integrated USB 2.0 Compatible 7-Port Hub PRODUCT FEATURES Data Brief Integrated USB 2.0 Compatible 7-Port Hub 7 Transaction Translators for highest performance High-Speed (480Mbits/s), Full-Speed
74VHC14 Hex Schmitt Inverter
74VHC14 Hex Schmitt Inverter General Description June 1993 Revised April 1999 The VHC14 is an advanced high speed CMOS Hex Schmitt Inverter fabricated with silicon gate CMOS technology. It achieves the
TVS/ESD Arrays. RLST23AxxxV Series. Circuit Protection System ELECTRONICS
ELECTRONICS TVS/ESD Arrays RLST23AxxxV Series TVS/ESD Arrays - RLST23AxxxV Series Features 350 Watts peak pulse power (tp = 8/20μs) Two devices protect two high-speed line pairs Low leakage current Low
SN54ALS04B, SN54AS04, SN74ALS04B, SN74AS04 HEX INVERTERS
SNALS0B, SNAS0, SN7ALS0B, SN7AS0 Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 00-mil DIPs description These devices contain
L9945. Automotive fully configurable 8-channel High/Low side MOSFET pre-driver suitable for 12 V and 24 V systems. Data brief.
Data brief Automotive fully configurable 8-channel High/Low side MOSFET pre-driver suitable for 12 V and 24 V systems Features TQFP64 exposed pad down Product status link L9945 Product summary GADG1606171506PS
2-wire Serial EEPROM AT24C01A AT24C02 AT24C04 AT24C08 AT24C16
Features Low-voltage and Standard-voltage Operation 2.7(V CC =2.7Vto5.5V) 1.8(V CC =1.8Vto5.5V) Internally Organized 128 x 8 (1K), 256 x 8 (2K), 512 x 8 (4K), 1024 x 8 (8K) or 2048 x 8 (16K) 2-wire Serial
2 TO 4 DIFFERENTIAL CLOCK MUX ICS Features
DATASHEET 2 TO 4 DIFFERENTIAL CLOCK MUX ICS557-06 Description The ICS557-06 is a two to four differential clock mux designed for use in PCI-Express applications. The device selects one of the two differential
Recent Advancements in Bus-Interface Packaging and Processing
Recent Advancements in Bus-Interface Packaging and Processing SCZA001A February 1997 1 IMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor
SN64BCT757 OCTAL BUFFER/DRIVER WITH OPEN-COLLECTOR OUTPUTS
SN64BCT757 OCTAL BUFFER/DRIVER WITH OPEN-COLLECTOR OUTPUTS SCBS479 MARCH 993 REVISED MAY 994 BiCMOS Design Significantly Reduces I CCZ ESD Protection Exceeds 2000 V Per MIL-STD-883C, Method 305; Exceeds
US72/73 Single Coil Fan Driver
Features and Benefits Full Bridge Driver High Sensitivity Hall Sensor Locked Rotor Shutdown and Auto-Restart Power-Efficient CMOS and Power MOSFETs Integrated tachometer (US72) or alarm (US73) signal outputs
CAT28C17A 16K-Bit CMOS PARALLEL EEPROM
16K-Bit CMOS PARALLEL EEPROM HALOGENFREE LEAD TM FREE FEATURES Fast Read Access Times: 200 ns Low Power CMOS Dissipation: Active: 25 ma Max. Standby: 100 µa Max. Simple Write Operation: On-Chip Address
2-wire Serial EEPROMs AT24C128 AT24C256. Features. Description. Pin Configurations. 128K (16,384 x 8) 256K (32,768 x 8)
Features Low-voltage and Standard-voltage Operation 5.0 (V CC = 4.5V to 5.5V) 2.7 (V CC = 2.7V to 5.5V). (V CC =.V to 3.6V) Internally Organized 6,34 x and 32,76 x 2-wire Serial Interface Schmitt Trigger,
EVAL-INAMP-62RZ/82RZ/82RMZ
Evaluation Boards for the AD620 Series and and the AD8220 Series Instrumentation Amplifiers EVAL-INAMP-62RZ/82RZ/82RMZ FEATURES 3 generic, easy-to-use PC boards Support several related in-amp products