EZ-9000 Tape Dispenser, EZ-9000-RP Tape Dispenser Part Number / MAY 2012 REV 1.0

Transcription

1 PLEASE NOTE Some of the part numbers are now different depending on when the unit was manufactured. The drawing will note where the appearance is different and the parts list will give you the correct part based on the S/N of the unit. See last page for the parts that are specific to the #66137 EZ-9000-RP

2

3

4

5

6 BODY SET 105 N/A CONTROL PANEL PART OF BLADE UNIT FLEXIBLE TAPE SUPPORT GEAR BOX FRONT GEAR BOX REAR TAPE SENSOR SLIDE PLATE PLATE ROLLER SENSOR LEVER BLADE PLATE CAM FIX BAR (LEFT)

7 CAM FIX BAR (RIGHT) BLADE GEAR # BLADE GEAR # BLADE GEAR # BLADE MAIN GEAR BLADE GEAR BEARING BLADE GEAR SHAFT SET OF 4 PCS BLADE MOTOR TRANSFORMER BRACKET TRANSFORMER EARTH WIRE To S/N N B EARTH WIRE S/N N & UP

8 INLET CABLE BLADE SENSOR COIL SPRING SET OF 2 PCS SPRING PLATE SHAFT SCREW M2.6 x 6L SET OF 2 PCS SCREW 3 x 8L SET OF 2 PCS BASE SET SEPARATOR GUIDE PLATE SUPPORT STAND TAPE HOLDER SET SET ONLY

9 TWEEZERS SILICON OIL SCREW M3 x 6L P.C.B. (C) INLET POWER SWITCH INLET CABLE P.C.B. (D) P.C.B. (E) EARTH TERMINAL P.C.B. COVER JOINT CABLE 24V

10 JOINT CABLE 9V INLET CABLE REMOVABLE ROLLER SET REMOVABLE ROLLER SET To S/N N From S/N N FRONT FRAME RIGHT To S/N N FRONT FRAME LEFT To S/N N FRONT FRAME RIGHT From S/N N FRONT FRAME LEFT From S/N N ROLLER # ROLLER # ROLLER #4 To S/N N ROLLER #4 From S/N N

11 TAPE OUTLET ROLLER BUSHING ROLLER BUSHING SET OF 2 PCS. TO S/N N SET OF 2 PCS. FROM S/N N ROLLER SPRING SET OF 2 PCS MAGNET SET OF 2 PCS EARTH PLATE M.R GEAR TO S/N N M.R GEAR FROM S/N N I. GEAR R.D. GEAR L.R. GEAR U.R. GEAR TO S/N N

12 U.R. GEAR FROM S/N N SCREW M3 x 11.3L SET OF 2 PCS WASHER SET OF 2 PCS ANTI-STATIC BRUSH OPTIONAL PARTS SET OF 5 PCS SIDE FRAME LEFT SIDE FRAME RIGHT TO S/N N SIDE FRAME RIGHT FROM S/N N CHECK PLATE MOTOR COVER ROLLER # BRUSH ROLLER #1

13 TAPE SUPPORT ROLLER SET OF 2 PCS LOWER TAPE HOLDER 610 N/A PART OF MOTOR ENCORDER R. GEAR D. GEAR TO S/N N D. GEAR FROM S/N N P.R. GEAR I. GEAR PLATE HANGER HANGER SPRING

14 Tape Guide Set Pin SET OF 2 PCS BUSHING SET OF 2 PCS SPRING LEFT SPRING RIGHT SCREW M3 x 6L SET OF 3 PCS SCREW M4 x 8L SET OF 2 PCS FRANGE NUT SET OF 2 PCS SCREW 4 x 12L SET OF 2 PCS P.C.B. (A) P.C.B. (B) LENGTH SENSOR P.C.B. (A) CABLE

15 P.C.B. (B) CABLE TO S/N N B P.C.B. (B) CABLE FROM S/N N HOLD DOWN ROLLER UNIT POWER CORD UL(120V) NOTE, the EZ-9000-RP is essentially a standard EZ-9000 bolted to the RP assembly. Part numbers available are ; Bobbin assembly includes all plastic pieces. Individual parts not available separately Bracket, holds all of the bobbins and rollers Base