YOU FOR CHOOSING UNITEC PARTS COMPANY UNITEC PARTS COMPANY

Transcription

1 Version 2 PROJECT INFORMATION 11/14/17 2:56 PM *Project Name: *Company Name: *Unitec Customer Account No: Customer contact: Cell Phone #: Total No. of Elevators: Total Car Operating Panels: Fax #: Office #: Ship to Address: City: State / Prov: Zip Code: Attention to: Cell Phone #: Office Phone #: Special Shipping Instructions: INSTRUCTIONS: 1. This document includes 11 forms (Project information, Button Configuration, Car Operating Panel, Hall Lanterns, In Car Lanterns, Hall Stations Flat Applied ( Terminal & Intermediate), Hall Stations Surface Mount (Terminal & Intermediate), Line Monitoring Device and Notes page). 2. After you complete each page, ALWAYS click the SAVE button. 3. Please send completed form to UNITEC VIA at info@unitecparts.com or fax to THANK YOU FOR CHOOSING UNITEC PARTS COMPANY Page 1/11

2 BUTTON CONFIGURATION Please identify button configuration (PICK ONE): Option 1 Micro-Motion III 3 Wire Type 1 (AMP Connector Type) Button Available Colors:,,, or Note: +24 VDC Button/LED Internal common and J1_1 is NOT used. Recommended Voltage: 24 VDC (Positive Button/LED common) Option 2 Micro-Motion III (Special 4 Wire) Type 1 (AMP Connector Type) Button Available Colors:,, or Note: Button Contact and LED are isolated from each other. Recommended Voltage: 24 VDC Contacts are rated up to 48 VDC Option 3 Micro-Motion II Type 2 (Screw Terminal Type) Button Available Color: Amber ONLY Note: Button Contact and LED are isolated from each other. Recommended Voltage (circle one): 120 VAC, or 120 VDC Controller Type: Motion Control Engineering (MCE) Virginia Controls Otis SmartRise Controls Elevator Controls (EC) Other: Button Types (PICK ONE): *Note: If you choose Luxury, you CANNOT select VANDAL Type: Halo Color: LUXURY Raised/ Flush: Finish: Flush Raised Stainless Steel *Note: Do not fill this section, if you chose LUXURY Flat Projecting Profille (Raised) Type: VANDAL LED Color: Flat Flush Profile (Flush) Rasied/ Flush: Flush Raised Finish: Stainless Steel Additional information for this Button Configuration is shown on the NOTES page Page 2/11

3 CAR OPERATING PANEL *Note: Please fill out one sheet per car operating panel COP size Faceplate: width standard Other: Car Station Type: Main AuxiliaryCHOOSE ONE ONLY length 67.0 standard Other: Alarm Voltage: 6 VOLT 12 VOLTCHOOSE ONE ONLY COP Wiring: Unwired Wired Faceplate Fastener: COP Finish: (Can only choose ONE) Tamper Resistant Locks Can only choose ONE Stainless Steel, Brushed, Brushed Other: Panel Engraving (filled black) Elevator No. Capacity pounds No Smoking (filled red) Other Position Indicator Color: ***NOTE: CE Driver may be required for Signal Fixtures - consult with Controller Manuf.*** K-Tech ADA Hands-Free Telephone: Emergency Light With Power Pack: Yes Yes No No Keyswitches (standard location) *Select UP TO 5 keyswitches (2) SPEED FAN KEYSWITCH ACCESS ENABLE KEYSWITCH (KEYED UTH) LIGHT KEYSWITCH INDEPENDENT SERVICE BLANK JEWEL (FIELD TO DEFINE & WIRE) BLANK KEYSWITCH (FIELD TO DEFINE & WIRE) OTHER Fire Service Cabinet Code Requirement: ANSI-96 ANSI-2000 ANSI-2004 ANSI-2007 ANSI-2009 ANSI-2010 CODE YEAR Fire Service Cabinet code Requirements includes: Specify Required SES Keyswitch Fireman's phonejack ANSI PHASE II KEYSWITCH CALL CANCEL BUTTON PHASE 1 "FIREHAT" ILLUMINATED JEWEL (FLASHING ILLUMINATION) EMERGENCY STOP TOGGLE SWITCH Floor Button/Braille Layout Braille Style (CHOOSE ONE): Stainless on black background on black background on black background (standard) Main Landing (please verify): Single Row Double Row Hinged: Right Left *Note: Right hand - Hinged on right side of COP when facing panel. Left hand - Hinged on left side of COP " " ". WALL BOX DIMENSIONS (1676 mm) 66" x (235 mm) 9.25" x (83 mm) 3.25 Certificate Frame Required? *Note: If you need to fill out information for an additional COP, please make a copy of this sheet Additional information for this Car Operating Panel is shown on the NOTES page Page 3/11

4 HALL LANTERNS Profile Flat Applied See Figure 1.1 Surface Mount Lantern Voltage Choose only ONE 30 VDC 120 VDC 120 VAC *Note : All Fixture material will be discrete unless noted otherwise. Figure 1.1 Color Car Directional Indicator: Multi-color (standard) Position Indicator: Audible Passing Gong: Yes No Lantern/PI Combo 318mm [12.50"] 260mm [10.25"] Hall Direction Lantern 203mm [8.00"] 146mm [5.75"] Hall Position Indicator 203mm [8.00"] 146mm [5.75"] 140mm [5.50"] 140mm [5.50"] 140 mm [5.50"] *Note: all drawings are shown horizontal Horizontal Vertical Faceplate Finish: Stainless steel Other, please specify Horizontal Vertical Faceplate Finish: Stainless steel Other Horizontal Vertical Faceplate Finish: Stainless steel Other Wall Box Dimensions 127 mm (5") wide 289 mm (11.37") long 89 mm (3.50") deep Wall Box Dimensions 127 mm (5") wide 173 mm (6.82") long 89 mm (3.50") deep Wall Box Dimensions 127 mm (5") wide 173 mm (6.82") long 89 mm (3.50") deep Additional information for this Hall Lanterns is shown on the NOTES page 4/11

5 IN CAR LANTERNS Profile See Figure 1.1 Flat Applied Lantern Voltage: 30 VDC 120 VDC 120 VAC Color: Multi-color (, or ) Figure 1.1 Audible Passing Gong: Yes No VANDAL LUXURY 89mm [3.50"] 89mm [3.50"] 132mm [5.20"] LENS 173.2mm [6.82"] 228.6mm [9.00"] 173.2mm [6.82"] 228.6mm [9.00"] Stainless steel Other, please specify: Stainless steel Other, please specify: Additional information for this In Car Lanterns is shown on the NOTES page Page 5/11

6 HALL STATIONS FLAT APPLIED - TERMINAL Face Plate Finish: Fire Service Code: Stainless Steel Other ANSI-1996 ANSI-2000 ANSI-2004 ANSI-2007 ANSI-2009 ANSI-2010 Other Terminal Up Top Faceplate Tamper Resistant Screws Terminal Up or Down 762 mm [30.00"] 76.2 mm [3.00"] 50.8 [2.00"] TYP x 4 Elevator Comm. Failure Jewel -w/ Buzzer Elevator Comm. Failure Keyswitch Fire Hat Jewel mm [22.20"] mm [20.55"] Fire Service Keyswitch Specify floors Type Single Access Keyswitch 965.2mm [38.00"] ABOVE THE FINISHED FLOOR ADA Notes (double click): Notes (double click): *Hall Stations dimensions will vary depending on options chosen. Additional information for this Hall Stations Flat Applied -Terminal is shown on the NOTES page Page 6/11

7 HALL STATIONS FLAT APPLIED - INTERMEDIATE Face Plate Finish: Stainless Steel Other Fire Service Code: ANSI-1996 ANSI-2000 ANSI-2004 ANSI-2007 ANSI-2009 ANSI-2010 Other Top Faceplate Tamper Resistant Screws 762 mm [30.00"] 76.2 mm [3.00"] 50.8 [2.00"] TYP x 4 Elevator Comm. Failure Jewel -w/ith Buzzer Elevator Comm. Failure Keyswitch Fire Hat Jewel Fire Service Keyswitch Specify floors mm [22.20"] mm [20.55"] Type 965.2mm [38.00"] ABOVE THE FINISHED FLOOR ADA Notes(double click): Notes (double click): *Hall Stations dimensions will vary depending on options chosen. Additional information for this Hall Stations Flat Applied - Intermediate is shown on the NOTES page Page 7/11

8 HALL STATIONS SURFACE MOUNT - TERMINAL Face Plate Finish: Stainless Steel Other Fire Service Code: ANSI-1996 ANSI-2000 ANSI-2004 ANSI-2007 Specify Fire Service Key Switch: ANSI-2009 ANSI-2010 Other: Please choose profile: Low Profile Mid Profile Terminal Up mm [6.50"] Top Faceplate mm [31.50"] 76.2 mm [3.00"] 50.8 [2.00"] TYP x 4 Elevator Comm. Failure Jewel -w/ Buzzer Elevator Comm. Failure Keyswitch Fire Hat Jewel Terminal Up or Down 564 mm [22.20"] mm [6.50"] Fire Service Keyswitch Specify floors Type ABOVE THE FINISHED FLOOR ADA HEIGHT Notes (double click here): *Hall Stations dimensions will vary depending on options chosen. ABOVE THE FINISHED FLOOR ADA HEIGHT Notes (double click here): Additional information for this Hall Stations Surface Mount - Terminal is shown on the NOTES page Page 8/11

9 HALL STATIONS SURFACE MOUNT - INTERMEDIATE Face Plate Finish: Stainless Steel Other Fire Service Code: ANSI-1996 ANSI-2000 ANSI-2004 ANSI-2007 Specify Fire Service Key Switch: ANSI-2009 ANSI-2010 Other: Please choose profile: Low Profile Mid Profile mm [6.50"] Top Faceplate mm [31.50"] 76.2 mm [3.00"] 50.8 [2.00"] TYP x 4 Elevator Comm. Failure Jewel with Buzzer Elevator Comm. Failure Keyswitch Fire Hat Jewel Fire Service Keyswitch Specify floors Type 564 mm [22.20"] mm [6.50"] Plastic Insert ABOVE THE FINISHED FLOOR ADA HEIGHT Notes (double click): *Hall Stations dimensions will vary depending on options chosen. ABOVE THE FINISHED FLOOR ADA HEIGHT Notes (double click): Additional information for this Hall Stations Surface Mount - Intermediate is shown on the NOTES page Page 9/11

10 LINE MONITORING DEVICE Please check all that apply: Integrall (stand-alone) fixture Flat Applied Profile Surface Mount Please choose profile: Low Profile Mid Profile 127 mm [5"] COMMUNICATION FAILURE 212 mm [8 254 mm [10"] *Note: Can be added to Applied Hall Stations - see pages 6, 7, 8 & 9 Additional information for this Line Monitoring Device is shown on the NOTES page Page 10/11

11 Comments / Notes: