DV220-XXXXX Ver. 7 Rel. 08/17/2011

Transcription

1

2 C.E. Electronics, Inc. Industrial Drive Bryan, OH 435 PH (49) 3-5 FX (49) XXXXX Ver. Rel. // COMPETITOR DOT MATRIX RENEWAL PARTS Lens: 4-55 Lens: 4- GRAY Lens: 4-9 BLUE DOT MATRIX LED DIGITAL INDICATOR Dot matrix LED digital indicator for floor position display, as well as car direction, if desired. Any alphanumeric or custom character can be displayed in either single digit with arrow or double digit floor designations. Typical Applications Hall stations Jamb mount PANEL PREPARATI #-3 x " STUD MIN (TYP. 4 PLACES) Features Low cost design Self contained unit Latched input Self testing Scrolling Passing chime output Error detection and correction feature UL listed CNECTI ' CABLE SUPPLIED WITH PLUG-IN CNECTOR FOR FLOOR S AND UP/DOWN ARROW..4" 3.".5" TO ORDER:-SPECIFY - X X X X X COLOR: "" "R" "A" MIXED AMBER "G" GREEN "B" BLUE "W" WHITE NUMBER OF S: "" OR LESS "" 3 "M" MICRO COMM LENS: "R" "G" GRAY "B" BLUE "X" NO LENS SIGNAL FORMAT: "" SINGLE LINE/FLOOR "" BINARY "3" UNITS & TENS "4" GRAY CODE "5" INVERTED BINARY "" SPECIAL "X" IF MICRO COMM " CHARACTERS NOTE:. If a special voltage is required, please consult factory.. VAC not required for power supply on Micro Comm units 3. Blue can not be mixed with other colors." 3.5" CUTOUT TOLERANCE: SIGNAL VOLTAGE: "A" POSITIVE -VDC, -4VAC "B" POSITIVE 4-4VDC, 4-4VAC "C" VAC "D" POSITIVE 5VDC "E" NEGATIVE -VDC "F" NEGATIVE 4-4VDC "G" NEGATIVE 5VDC "X" IF MICRO COMM

3 J XX-XM JOB# S3 DIP SWITCH DETAIL CE39 3 S3 DEFAULT SETTINGS ROTARY SWITCH S DRIVER BOARD# CODE VERSI DISPLAY BOARD# CODE VERSI FLOORS: NOT USED FIRE MAIN BLANK FLOOR SELECTI OFF MICRO COMM S S 9 3 A B C D E F R5 R4 R3 3 J COM V+ DATA 4 REAR FA SELF-TEST JACK ROLL RATE ADJUSTMENT PASSING CHIME J 3 4 FM MB S CE5 CE5 U4 CE3 To SELF-TEST display unit, short the two pins on the S header and release. NOTE: If S is a rotary switch, set it to "F" and back to to self-test. DIP switch (MB) has no function with this unit. The Micro Comm driver must be programmed to send messages with the level required to activate the features listed below. 3 CE3 - To blank the display during a fire main (level three) message, turn on DIP switch (FM). U4 CE3 U4 CE3 - To blank the display during a fire alternate (level two) message, remove resistor R3 (FA) from the board. - Do not program a floor value for Floor 3 if the Fire Blanking feature is required. DIP switches 3- off is an all call using travel signals. DIP switches 3- on and resistor R5 (4) removed is an all call using arrival signals. The floor address switches setup the display arrows as arrival (hall) arrows. Refer to the "S3 DIP SWITCH DETAIL" and turn on the floor address switches whose value adds up to the desired floor. For example, to display the arrows only when the unit is at floor 9, turn on switches 3, 4, and (values,, and : ++9). The Micro Comm driver must be set up to send arrival information. To operate this unit as a rear lantern, remove resistor R4 (REAR) from the board. NOTE: The Micro Comm driver must be sending the MC data stream to use this feature. Call Tech Support at for more information. NOTE: MUST BE USED WITH A CLASS POWER SUPPLY. //5 C.E. ELECTRICS, INC. Industrial Drive Bryan, Ohio , 3 // (49) 3-5 PRODUCT DWG. NO. REV: XXX-XM VERTICAL DOT MATRIX DISPLAY XXX-XM_ A

4 U4 9 A B CD E F J5 PASSING CHIME S ISO ISO5 ISO4 ISO3 ISO ISO R5 J DH DH3 DH SCROLL RATE: NO SCROLL FAST SCROLL F SLOW SCROLL OPTIAL CHIME PORT 3 SELF-TEST JACK: SHORT PINS TO TEST SHORT PINS TO S TEST S R R3 R4 R R J3 J ARROW VOLTAGE SIGNAL VOLTAGE (FROM CTROLLER) E LINE PER FLOOR FLOOR SIGNAL FLOOR SIGNAL FLOOR 3 SIGNAL FLOOR 4 SIGNAL FLOOR 5 SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR 9 SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR 3 SIGNAL FLOOR 4 SIGNAL FLOOR 5 SIGNAL FLOOR SIGNAL UP ARROW DOWN ARROW BINARY A () A () A3 (4) A4 () A (3) A5 () BLACK WHITE GREEN ORANGE BLUE WHT/BLK /BLK GRN/BLK ORG/BLK BLU/BLK BLK/WHT /WHT GRN/WHT BLU/WHT BLK/ WHT/ ORG/ J JOB# BLU/ /GRN COMM ARROW COMM ISO R LY USED FOR E LINE PER FLOOR ABOVE FLOORS R DH3 CE3 CE3E ISO VAC R R JP 5 D U FLOOR SIGNAL FLOOR SIGNAL FLOOR 9 SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR 3 SIGNAL FLOOR 4 SIGNAL FLOOR 5 SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR 9 SIGNAL FLOOR 3 SIGNAL FLOOR 3 SIGNAL BLACK WHITE GREEN ORANGE BLUE WHT/BLK /BLK GRN/BLK ORG/BLK BLU/BLK BLK/WHT /WHT GRN/WHT BLU/WHT J3 SEE NOTE ( ) BELOW 3 DRIVER BOARD CE3 VERT DISPLAY BOARD CE ROTARY SWITCH S HORIZ DISPLAY BOARD CE CODE VERSI OP N/C 5 VAC Competitor Series Discrete Input Dot Matrix Displays NOTE A: THE SIGNAL AND ARROW COMMS ARE TIED TOGETHER THE DRIVER BOARD. IF ARROW SOURCE IS DIFFERENT THAN SIGNAL SOURCE, CTACT TECH SUPPORT AT FOR FURTHER INFORMATI. NOTE B: THE SIGNAL AND ARROW COMMS HAVE BEEN SEPARATED BY THE FACTORY. 4/4/ 3 - C.E. ELECTRICS, INC. Industrial Drive Bryan, Ohio 435 (49) 3-5 PRODUCT DWG. NO. REV: DISCRETE DOT MATRIX DISPLAYS DM_3_3_33 -

5 A A A5 A4 A3 A A BINARY BITS BINARY FLOOR CHART INSTALLATI GUIDE. MAKE SURE THE RESISTORS ARE FULLY SEATED IN THEIR SOCKETS.. CNECT 5VAC TO THE OUTER TERMINALS OF CNECTOR J. THE CENTER TERMINAL HAS NO CNECTI. 3. SHORT THE TWO PINS OF S (TEST JACK) TOGETHER. THE DISPLAY WILL CYCLE THROUGH THE FLOOR DATA. THIS SHOWS WHAT FLOOR MARKINGS WILL BE DISPLAYED AND ALLOWS ADJUSTMENT OF THE SCROLL RATE AND OPTIAL PASSING CHIME VOLUME. 4. MAKE SURE THE SIGNAL CABLE(S) IS PLUGGED INTO THE DRIVER BOARD CORRECTLY. 5. CNECT THE SIGNAL CABLE(S) TO THE CTROLLER. THE VOLTAGE AND DC POLARITY ARE MARKED THE REVERSE SIDE. THE UNIT WORKS LIKE A LIGHT BULB; IT NEEDS VOLTAGE FROM COMM TO THE SELECTED.. IF THE IS DC AND YOU SUSPECT THE POLARITY IS WRG, PUT THE SELECTED FLOOR WIRE TO COMM AND COMM TO THE SELECTED FLOOR. IF THE UNIT DISPLAYS THE FLOOR, CTACT TECH SUPPORT.. IF THE FORMAT IS SINGLE LINE PER FLOOR, LY E WIRE SHOULD HAVE VOLTAGE PRESENT (WITH REFERENCE TO COMM) AT ANY TIME.. IF THE UNIT DOES NOT SEEM TO WORK PROPERLY, RECHECK THE ABOVE STEPS. IF THE PROBLEM CTINUES, RECORD THE SERIAL NUMBER FROM THE WHITE LABEL THE UNIT AND EXACTLY WHAT THE UNIT DISPLAYS AT EACH FLOOR, THEN CTACT TECH SUPPORT AT C.E. ELECTRICS, INC. Industrial Drive Bryan, Ohio 435 (49) 3-5 PRODUCT DWG. NO. REV: 4/4/ N/A COMPETITOR SERIES BINARY FLOOR CHART COMP_BINCHART_TJ - -