Holovision units with VIK(sip) Intercom Modules. Firmware v 2.9 setup v For firmware v 1.09, please see Appendix 1
|
|
- Olivia Lambert
- 5 years ago
- Views:
Transcription
1 Integration Note Manufacturer: Model Number(s): Comments: Holovision SIP Door Station Holovision units with VIK(sip) Intercom Modules Firmware v 2.9 setup v 1.05 For firmware v 1.09, please see Appendix 1 Minimum Core Module 7.2.xxx Document Revision Date: 07/15/2016 OVERVIEW AND SUPPORTED FEATURES The Holovision VIK SIP Door Station is an SIP Door Station solution without an integrated video camera for monitoring door activity. ELAN g! integration with the station supports the following features: 1. Paging- When the Call button is pressed on the Door Station, it will call all appropriate Intercom Stations based on the House Mode of the g! System 2. 2 Way Calls- A user at an Intercom Station can converse with the person who pressed the Call button 3. Video Monitoring- Any ONVIF Camera in the g! System may be paired with the Door Station to provide one-way video monitoring of the station 4. Relay/Door Strike Actuation through the UI (FIRMWARE 1.09 ONLY)- As of the release of g! 7.3, Relays and Door Strikes are supported through the Door Station Interface when using firmware Relay/Door Strike Actuation through Event Mapper (FIRMWARE 1.09 ONLY)- As of the release of g! 7.3, Relays and Door Strikes are supported through the Event Mapper when using firmware Relay/Door Strike Actuation through DTMF. INTEGRATION REQUIREMENTS NOTE: The Holovision Door Station REQUIRES a PoE (Power over Ethernet) connection. It is not possible to power the station any other way. Either a PoE router/switch or a PoE injector MUST be used with this device. The Holovision Door Station requires a single CAT5 Ethernet connection to the same network to which the g! Intercom Controller is attached: Pull the CAT5 cable from the door station location to the Network Switch or Router Terminate both ends of the cable Test the cable to ensure proper performance Connect the Door Station; ensure that it powers up. ELAN Home Systems 1690 Corporate Circle Petaluma, CA USA tech support: main: sales: elan@elanhomesystems.com 2013 ELAN Home Systems. All rights reserved. ELAN and g! are trademarks of ELAN Home Systems. All other trademarks are the property of their respective owners.
2 PROGRAMMING HOLOVISION VIKING WITH FIRMWARE V 2.9 These instructions are for Firmware 2.9. See Appendix 1 for instructions using firmware 1.09 and older configuration utilities, NOTE: Prior to setting up the SIP component of the Door Station, you will need to enable the SIP Server in the g! Controller. Please see the Intercom Integration Note for details on this configuration. SIP VOIP: 1. Launch the Viking VoIP Phone Programming utility. 2. The software will show the current settings for the station. Perform the following changes 3. Phone Numbers / Codes / Audio Tab a. Configure information as appropriate for your region and preferences. 4. Phone Settings Tab Notes a. Relay Mode should be Door Strike b. Relay Activation Command will determine key sequence to activate door strike c. Lap Counter: set it up as shown d. Dial Next No on Ring No answer: This determines the units time to ring. The highest setting is 9 which is about 1 minute
3 5. IP Settings Tab Notes a. Configure IP as appropriate for your network. b. Phone Name is what will show up in g! configurator
4
5 G! CONFIGURATION DETAILS CONFIGURE THE DOOR STATION The Door Station should connect to the g! Controller as soon as it is provided the IP Address of the SIP server. When it connects, it will automatically populate under the Door Station heading on the Messaging tab in Configurator. No configuration of the door station should be needed to provide SIP functionality: Although the door station does not have a built-in camera, you may assign an ONVIF camera to monitor the station. Use the Video drop down menu to select the camera you wish to associate with the door station. CONFIGURE THE RELAYS FOR THE DOOR STATION With Holovision Viking firmware 2.9, realys must use DTMF for activation. Under Options, configure the Relays to use DTMF; sip:holovision
6 Common Mistakes 1. No Video. If there is no video for the door station in the viewer, ensure that the Video drop-down for the Door Station on the Messaging tab has the correct camera selected. 2. Door Station not populating in the Viewer. Make sure that the Door Station has populated on the Messaging tab in Configurator. Check the settings in the Door Station Web GUI to make sure the g! Controller is assigned as the SIP server. 3. No Page signal sent when button is pressed. Ensure that the Dial Plans are set up correctly and the system is in the correct System Mode for the Dial Plan. See the Intercom Integration Note for details on setting up Dial Plans 4. Door Station continues to ring after time expires. In the Viking software utility, set Lap Counter to 1 and Dial next number on ring no answer to Tier 2 dial plans don t ring: Dial next on no answer is actually what determines the unit s time to ring. The highest setting is 9 which is about 1 minute. IF someone has this set to 3(like the old firmware), then that is approximately 15 seconds. If you are using tier 2 on the dial plan, the timeouts cannot go longer than the total call time. So if that is set to 9 (1 min) and I have tier 1 set to 60 seconds timeout, tier 2 will never ring.
7 APPENDIX 1: PROGRAMMING HOLOVISION VIKING WITH FIRMWARE V 1.09 These instructions are for Firmware VA1.09, WebUI V12.12, Bootloader V99.26, Setup V01.01 NOTE: Prior to setting up the SIP component of the Door Station, you will need to enable the SIP Server in the g! Controller. Please see the Intercom Integration Note for details on this configuration. SIP VOIP: 1. Launch the Viking VoIP Phone Programming utility. 2. In the Phone Name window, select the door station you wish to configure, then click the Connect button. The software will show the current settings for the station.
8 3. Perform the following changes: a. Set Phone Name to a name appropriate to the station, i.e. Front Door or Garage Entry. Press the Set Name button to save the name to the station. b. In the Information Phone Numbers section, enter 1. Press the Write Numbers button to save the information to the station. c. If desired, give the station a static IP address. d. In the SIP Server Settings box, enter the IP Address of the System Controller. Other options should remain at default. Press the Write IP Settings button to save the IP Configuration to the station. G! CONFIGURATION DETAILS FIRMWARE 1.09 ONLY CONFIGURE THE DOOR STATION The Door Station should connect to the g! Controller as soon as it is provided the IP Address of the SIP server. When it connects, it will automatically populate under the Door Station heading on the Messaging tab in Configurator. No configuration of the door station should be needed to provide SIP functionality:
9 Although the door station does not have a built-in camera, you may assign an ONVIF camera to monitor the station. Use the Video drop down menu to select the camera you wish to associate with the door station. CONFIGURE THE RELAYS FOR THE DOOR STATION As of the release of g! 7.3, the relays on the Holovision may be added into Configurator in order to display a button in the UI, allowing the end user to press a button in the interface to open the door after verifying to whom they are speaking. Before this feature may be used, the Relays must be added on the Input/Output tab. In the Relay Outputs section, right click and select Add New Output Controller :
10 Select the option for Holovision Viking IP Relay Control then click OK. The Relay Control will be added, and when expanded, the tree will show all available relays on the station. It is possible to rename these relays to a value that corresponds with their location, for example Front Door Relay 1 to make further configuration more intuitive. Once the relays are added to the Input/Output tab, it is possible to use them in the Event Mapper. In order to get the relays to appear on the Door Station User Interface, further configuration is required in the Messaging tab. ADD RELAYS TO THE USER INTERFACE (UI) Once the relays have been configured on the Input/Output tab, they can be added to the Door Station UI from the Messaging tab. Select the correct Door Station from the Tree and expand the list by clicking on the + sign next to the heading. Select the Options tree item and you will be able to assign the relays to buttons in the interface. Up to two buttons per door station may be enabled in the Door Station UI (Labeled as Output 1 and Output 2 in Configurator), any other relays may be actuated with the Event Mapper. Use the Dropdown labeled Output to assign the correct relay. The Interface button will be populated with the Name in the Output 1 Name field. The type of relay (Toggle or Momentary) may be selected from the Output Type dropdown.
Integration Note OVERVIEW AND SUPPORTED FEATURES INTEGRATION REQUIREMENTS. DoorBird Firmware and greater. Document Revision Date: 11/15/2017
Integration Note Manufacturer: Bird Home Automation GmbH Model Number(s): Comments: Document Revision Date: 11/15/2017 DoorBird D10x, D20x OVERVIEW AND SUPPORTED FEATURES DoorBird Firmware 000099 and greater
More informationModel Number(s): Mirage Media Server (Autonomic MMS-x Devices)
Integration Note Manufacturer: Autonomic Model Number(s): Mirage Media Server (Autonomic MMS-x Devices) Minimum Core Module Version: 6.5 Comments: Written and tested with FW REV 5.0.14545.0 Document Revision
More informationVSX-60, SC-61, SC-63, SC-65, SC-67, SC-68
Manufacturer: Model Number(s): Pioneer Integration Note VSX-60, SC-61, SC-63, SC-65, SC-67, SC-68 Core Module Version: Core Module 5.8 or later required Comments: VSX-60 with FW 1-157-076-014-091 tested.
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES. Model Number(s): SR6006, SR5006
Manufacturer: Marantz Integration Note Model Number(s): SR6006, SR5006 Core Module Version: 5.4 or newer required Document Revision Date: 1/15/2013 OVERVIEW AND SUPPORTED FEATURES Marantz receivers include
More informationMinimum Core Module Version: 4.0 Build 1452 Comments: AXIS IP Utility , Camera Firmware 4.40 Document Revision Date: 2/13/2013
Integration Note Manufacturer: Axis Model Number(s): 214PTZ Minimum Core Module Version: 4.0 Build 1452 Comments: AXIS IP Utility 2.21.0, Camera Firmware 4.40 Document Revision Date: 2/13/2013 OVERVIEW
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES. IP Video Cameras (See models list below) NOTE: Only Panasonic Petcams, Residential cams, and
Manufacturer: Panasonic Integration Note IP Video Cameras (See models list below) NOTE: Only Panasonic Petcams, Residential cams, and Model Number(s): Commercial cams are supported. The Panasonic i-pro
More informationCamera Firmware or (5.50 fixes security vulnerability introduced in 5.20) Document Revision Date: 07/15/2016
Manufacturer: Model Number(s): Axis P3301 Integration Note Minimum Core Module Version: g! 6.1.34 Comments: Camera Firmware 5.11.1 or 5.50.4.4 (5.50 fixes security vulnerability introduced in 5.20) Document
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES. Model Number(s): SR5008/6008/7008
Manufacturer: Marantz Integration Note Model Number(s): SR5008/6008/7008 Minimum Core Module Version: 6.5 Comment: Tested SR7008 FW: 5330-0346-9582 Document Revision Date: 12/30/2013 OVERVIEW AND SUPPORTED
More informationA suggested source is Opternus:
Manufacturer: KNX Input / Output Integration Note Model Number(s): (Various) Core Module Version: g! Core Module 5.4 or newer Document Revision Date: 1/9/2013 OVERVIEW AND SUPPORTED FEATURES KNX systems
More informationExtender Controller Integration Note
Extender Controller Integration Note Manufacturer: Model Number(s): ELAN SC2, SC10 Core Module Version: g! Core Module 7.0.178 Document Revision Date: 07/09/2014 OVERVIEW AND SUPPORTED FEATURES ELAN SC
More informationModel Number(s): WPS-300-DVR-9CH, WPS-300-DVR -16CH
Integration Note Manufacturer: SnapAV Model Number(s): WPS-300-DVR-9CH, WPS-300-DVR -16CH Core Module Version: 6.4.200 Comments: Hardware Version 02.00.00; Firmware Version 07.80.53 Document Revision Date:
More informationMirage Media Server (Autonomic MMS-x Devices)
Manufacturer: Autonomic Integration Note Model Number(s): Core Module Version: g! 6.5 Mirage Media Server (Autonomic MMS-x Devices) Comments: Written and tested with FW REV 5.0.14545.0 Document Revision
More informationThe Texecom Premier Elite security panels integrate with the g! system using either an Ethernet connection or an RS-232 serial connection.
Manufacturer: Texecom Integration Note Model Number(s): Premier Elite Series Core Module Version: 6.4.200 Comments: Tested with Premier Elite 48 Document Revision Date: 8/6/2013 OVERVIEW AND SUPPORTED
More informationMinimum Core Module Version: g! version 5.4, requires S1616A Firmware Document Revision Date:
Manufacturer: ELAN Integration Note Model Number(s): System S1616A (Multi-Zone Control) Minimum Core Module Version: g! version 5.4, requires S1616A Firmware 2.0.2.2 Document Revision Date: 05-25-2017
More informationModel Number(s): D7000, D9000 Series Panels, D7000/9000V2 Panels
Manufacturer: Bosch / Radionics Integration Note Model Number(s): D7000, D9000 Series Panels, D7000/9000V2 Panels Core Module Version: Comments: Tested Firmware Revisions: 6.80, 7.07 Document Revision
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES. Model Number(s): (Various)
Integration Note Manufacturer: KNX Lighting Model Number(s): (Various) Minimum Core Module Version: 5.4 Document Revision Date: 2/11/2013 OVERVIEW AND SUPPORTED FEATURES KNX lighting systems are designed
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES INSTALLATION OVERVIEW. Model Number(s): V883, V85
Manufacturer: ELAN Home Systems Model Number(s): V883, V85 Core Module Version: 4.0.1288 and newer (V883) 4.0 1587 and newer (V85) Document Revision Date: 1/15/2013 Integration Note OVERVIEW AND SUPPORTED
More informationCore Module Version: Comments: Firmware: Release 4.15, Prom v1.70g, DSP Document Revision Date: 1/10/2013
Manufacturer: ADA Integration Note Model Number(s): Suite 7.1 Core Module Version: Comments: Firmware: Release 4.15, Prom v1.70g, DSP 2.1.5201 Document Revision Date: 1/10/2013 OVERVIEW AND SUPPORTED FEATURES
More informationcontrol4 GSM Gateway Setup
2014 control4 GSM Gateway Setup Roger Althaus control4all 13.06.2014 Table of content General... 2 Introduction... 2 Features... 2 Supported Hardware and Software... 2 Limitations... 2 Installation...
More informationIntegration Note. Manufacturer: OVERVIEW AND SUPPORTED FEATURES. Model Number(s): Power Series / 5401
Manufacturer: DSC Integration Note Model Number(s): Power Series / 5401 Core Module Version: 4.0 (all builds) Comments: Document Revision Date: 1/30/2013 OVERVIEW AND SUPPORTED FEATURES The DSC Power Series
More informationIntegration Note. Manufacturer: OVERVIEW AND SUPPORTED FEATURES. Model Number(s): DSC POWER SERIES / IT-100
Manufacturer: DSC Integration Note Model Number(s): DSC POWER SERIES / IT-100 Core Module Version: 6.4.209 Comments: Document Revision Date: 9/11/2013 OVERVIEW AND SUPPORTED FEATURES The DSC Power Series
More informationApplication notes for Algo 8028 SIP Doorphone with Avaya IP Office Release 7.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application notes for Algo 8028 SIP Doorphone with Avaya IP Office Release 7.0 Issue 1.0 Abstract These Application Notes describe the configuration steps required
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES THE FOLLOWING FEATURES ARE SUPPORTED: THE FOLLOWING FEATURES ARE NOT SUPPORTED:
Manufacturer: Atlona Integration Note AT-PRO2HD 88M, 1616M, 44M (HD-BaseT) AT-HD-V 44M, 1616M (HDMI) Model Number(s): AT-PRO3HD44M, 66M (HD-BaseT) AT-H2H-44M, 88M (HDMI) Device Tested: ATPRO2HD1616M FW1.1.14,
More informationIntegra DTR-20.7/30.7/40.7/50.7/60.7/DHC-60.7 Onkyo TX-NR545/646TX-RZ800/900
Manufacturer: Model Number(s): Core Module Version: 7.2.639 Integra/Onkyo Comments: Tested: Integra 40.7 Document Revision Date: 10/12/2015 OVERVIEW AND SUPPORTED FEATURES Integration Note Integra DTR-20.7/30.7/40.7/50.7/60.7/DHC-60.7
More informationR2D7 Serial Interface for RP60 motor
Integration Note Manufacturer: Electronic Solutions, Inc. Model Number(s): R2D7 Serial Interface for RP60 motor Minimum Core Module Version: Document Revision Date: 2/11/2013 OVERVIEW AND SUPPORTED FEATURES
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES LUTRON LIGHTING SYSTEMS SUPPORT THE FOLLOWING FEATURES:
Integration Note Manufacturer: Model Number(s): Lutron Minimum Core Module Version: g! 7.3 Caseta Lighting Control Comments: Driver Version 0.0.9 Document Revision Date: 12/28/2015 OVERVIEW AND SUPPORTED
More informationVIDEOPHONE CONFIGURATION GUIDELINE VERSION 1.0
VIDEOPHONE CONFIGURATION GUIDELINE VERSION 1.0 REV3 13.09.2012 INDEX 1 INTRODUCTION 3 1.1 Purpose 3 1.2 Installation example Building A 4 1.2.1 Device selection 5 1.2.2 Scheme 6 2 CONFIGURATION 7 2.1 Internal
More informationIMPORTANT! GE Caddx panels cannot support PIN codes then end in zero over RS-232. See Common Mistakes for more information.
Manufacturer: GE NetworX Integration Note Model Number(s): NX-4,6,8 Core Module Version: Document Revision Date: 01/09/2016 OVERVIEW AND SUPPORTED FEATURES The NetworX NX-4,6,8 security panels integrate
More informationIntegration Note. Manufacturer: OVERVIEW AND SUPPORTED FEATURES. Model Number(s): MAXSYS Series
Manufacturer: DSC Integration Note Model Number(s): MAXSYS Series Core Module Versions: 4.0 (all builds) Comments: Document Revision Date: 1/30/2013 OVERVIEW AND SUPPORTED FEATURES The DSC MAXSYS Series
More informationTechNotes. Revision 6/6/ Custom Video Tabs
TechNotes Revision 6/6/20112011 Custom Video Tabs Overview: Custom Video tabs are useful for including extended functionality on a camera page. Examples of the uses of Custom Video tabs include setting
More informationTHIS SONOS CONNECT AMP DRIVER SUPPORTS THE FOLLOWING FEATURES: Any feature not specifically noted as supported is not supported.
Integration Note Manufacturer: Model Number(s) Sonos Sonos Connect Amp (+ Virtual Aux Feeds) Minimum Core Module Version: 7.3.271 Document Revision Date 01/03/2016 v1.0.6 OVERVIEW AND SUPPORTED FEATURES
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES. Minimum Core Module Version: Document Revision Date: 09/25/2017
Integration Note Manufacturer: Pentair Water Model Number(s): IntelliTouch, EasyTouch Minimum Core Module Version: Document Revision Date: 09/25/2017 OVERVIEW AND SUPPORTED FEATURES Installing a Pentair
More informationor newer required for Shoutcast internet radio or newer required for itunes and m4a file support Notes:
Manufacturer: HC Internal Player Integration Note Core Module Versions: 5.1.401 or newer required for Shoutcast internet radio 5.2.568 or newer required for itunes and m4a file support Notes: This document
More informationUsing the CyberData Video Intercom with the Linphone App for Android and ios
The IP Endpoint Company Using the CyberData Video Intercom with the Linphone App for Android and ios Document Part #931434A CyberData Corporation 3 Justin Court Monterey, CA 93940 T:831-373-2601 F: 831-373-4193
More informationConfiguration and Application of Phone and Door Control
Configuration and Application of Phone and Door Control Version: Release date: Contents CONTENTS... 1 1 INTRODUCTION... 2 1.1 Overview... 2 1.2 Applicable Models... 2 2 OPERATION DESCRIPTION...
More informationAlgo 8028 SIP Doorphone Manual. Empowered by Innovation P/N ALGO
Empowered by Innovation Algo 8028 SIP Doorphone Manual P/N 1093100ALGO August 19, 2015 Printed in U.S.A. For additional resources, visit our Technical Support site on the web at http://www.necdsx.com.
More informationFurman F1000, F1500 Panamax M4320, MB1000, MB1500
Manufacturer: Model Number(s): Core Module Version: Document Revision Date: 2/1/2013 Furman, Panamax OVERVIEW AND SUPPORTED FEATURES Furman F1000, F1500 Panamax M4320, MB1000, MB1500 g! 5.6 or newer Integration
More information4.0 Build or newer
Manufacturer: Model Number(s): Core Module Version: Comments: Nuvo Document Revision Date: 1/17/2013 Essentia E6G 4.0 Build 1452.0 or newer OVERVIEW AND SUPPORTED FEATURES THE FOLLOWING FEATURES ARE SUPPORTED:
More informationAudio Servers S1, H1, H3, H5CD and Others
Integration Note Manufacturer: S1Digital Model Number(s): Core Module Version: Comments: Audio Servers S1, H1, H3, H5CD and Others g! 6.0 and above Document Revision Date: 3/9/2016 S1Digital Software 2.2-2.4.x
More informationSoftware 4.0 Build Rel or later. Nuvo Grand Concerto FW v2.56, HWv00; M3 Server v1.60, ipod v1.53 Document Revision Date: 1/17/2013
Manufacturer: Model Number(s): Core Module Versions: Nuvo Grand Concerto Software 4.0 Build 1452.0 Rel or later Integration Note 6.0.236 and newer includes zone controller integration only, no virtual
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES
Manufacturer: Model Number(s): Minimum Core Module Version: Comment: Document Revision Date: Marantz Integration Note SR5008/5009/5010/5011/6008/6009/6010/6011/7008/7009/7010 /7011 NR1506/1606/1607 AV7703
More informationUsing CyberData Devices with a Grandstream UCM6102 IP PBX
1 Using CyberData Devices with a Grandstream UCM6102 IP PBX This is a sample of CyberData products, please visit cyberdata.net for a complete list. Document: Draft Date: 07/10/2017 Version 1 CyberData
More informationTHIS NIKO HOME CONTROL DRIVER SUPPORTS THE FOLLOWING FEATURES: Any feature not specifically noted as supported is not supported.
Integration Note Manufacturer: Niko Model Number(s) Niko Home Control (Lighting) Minimum Core Module Version: 7.3.271 Document Revision Date 02/03/2016 v2.0.2 OVERVIEW AND SUPPORTED FEATURES This driver
More informationIntegration Note OVERVIEW AND SUPPORTED FEATURES
Manufacturer: Model Number(s): KNX Climate (Various) Minimum Core Module g! 5.4 Version: g! 6.2 Minimum for Fan Coil Climate Modes Document Revision Date: 10/8/2015 OVERVIEW AND SUPPORTED FEATURES Integration
More informationDMP 128 Plus C V DMP 128 Plus C V AT
DMP 128 Plus C V DMP 128 Plus C V AT Interactive Intelligence Configuration Guide REVISION: 1.0.1 DATE: MARCH 7 TH 2018 Revision Log Date Version Notes Feb 9 th 2018 1.0 First Release: Applies to Firmware
More informationSetting Up The HikVision Villa IP Intercom for The First Time
Setting Up The HikVision Villa IP Intercom for The First Time Introduction This tech note will step you though the steps to setting up the HikVision Villa IP Intercom for the first time as a hardwired
More informationGrandstream Networks, Inc. Connecting GDS3710 with GXP IP Phones Configuration Guide
Grandstream Networks, Inc. Table of Contents SUPPORTED DEVICES... 3 INTRODUCTION... 4 PEERING SCENARIO... 5 GDS3710 Configuration Settings... 5 GXP IP Phones Configuration... 7 CONNECTION USING SIP SERVER...
More informationidor Mobile Setup idor Mobile : idor Mobile System Manual V1.1 1
idor Mobile Setup Table of Contents Login into the Web-GUI... 3 Network Settings... 4 Set Static IP Address... 5 Apartments... 7 Add an Apartment... 7 Edit an Apartment... 9 Delete an Apartment... 9 SIP
More informationApplication Notes for Configuring 2N Telekomunikace Helios IP to interoperate with Avaya IP Office Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring 2N Telekomunikace Helios IP to interoperate with Avaya IP Office 7.0 - Issue 1.0 Abstract These Application Notes describe the
More informationSetting Up IP Intercom For The First Time With WiFi Room Stations Only
Setting Up IP Intercom For The First Time With WiFi Room Stations Only Introduction This tech guide will step you though the steps to set up the HikVision Villa IP Intercom for the first time when using
More informationApplication Notes for Talkaphone VOIP-500 Series and VOIP-600 Series IP Call Stations with Avaya IP Office - Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Talkaphone VOIP-500 Series and VOIP-600 Series IP Call Stations with Avaya IP Office - Issue 1.0 Abstract These Application Notes describe
More informationProtege Vandal Resistant Touchscreen Intercom Entry Station
Protege Vandal Resistant Touchscreen Intercom Entry Station Located at the main entrance, the 17 touchscreen entry station is likely to be the first thing people notice as they approach the building. Designed
More informationVIP-102B IP Solutions Setup Tool
VIP-102B IP Solutions Setup Tool Version 7.5.0.0 Reference Manual Revision 7-10/4/18 For latest updates to this manual please check our website at: http://www.valcom.com/vipsetuptool/default.htm Then click
More informationAlphaCom SIP GSM Gateway
Ship Shore GSM antenna ACM system IP network GSM gateway Public telephone network TECHNICAL MANUAL AlphaCom SIP GSM Gateway MV-370 TECHNICAL MANUAL A100K10390 v.2.0 Document Contents 1 BASIC INFORMATION
More informationRef. 1717/31 (White) Ref. 1717/33 (Black)
Mod. 1717 DS1717-020 LBT20144 IP 7 TOUCHSCREEN MONITOR Ref. 1717/31 (White) Ref. 1717/33 (Black) COMPLETE USER MANUAL The information contained in this manual has been carefully collected and checked;
More informationRING CENTRAL CONFIGURATION GUIDE: V3 SIP-ENABLED IP INTERCOMS
RING CENTRAL CONFIGURATION GUIDE: V3 SIP-ENABLED IP INTERCOMS Document Part #931105C 3 Justin Court Monterey, CA 93940 (831) 373-2601 Doc. 931105C Page 1 RingCentral Configuration Guide: SIP-Enabled IP
More informationInstalling SMS without a network
Tech Note 6 January 15, 2009 Installing SMS without a network Why would I install SMS without using a pre-existing network? The building is not yet networked but will be. Desire to keep the security system
More informationIntegration Note. mhub4k431, mhub4k862, mhub4k44pro & mhub4k88pro
Integration Note Manufacturer: Model Number(s): HDAnywhere mhub4k431, mhub4k862, mhub4k44pro & mhub4k88pro g! Core Module Version: 8.1.401 Driver Developer: Core Programming Limited Document Revision Date:
More informationLive or Recorded Video: Video output from the NVR is not available in the ELAN Viewer.
Manufacturer: Model Number(s): Core Module Version: 7.3 SnapAV Document Revision Date: 10/10/17 OVERVIEW AND SUPPORTED FEATURES Integration Note LUM-500-NVR-4CH, LUM-500-NVR-8CH, LUM-500-NVR-16CH The SnapAV
More informationDRG-Series. Digital Radio Gateway. Hytera DMR IP (Tier-2) Digital Radio Supplement
DRG-Series Digital Radio Gateway Hytera DMR IP (Tier-2) Digital Radio Supplement DRG-Series Digital Radio Gateway Hytera DMR IP (Tier-2) Digital Radio Supplement 2017 Omnitronics Pty Ltd. All rights reserved.
More informationSetting Up The Hikvision IP Intercom For The First Time
Setting Up The Hikvision IP Intercom For The First Time Introduction 01/03/2018 This tech note will step you though the steps to setting up the HikVision IP Intercom for the first time as a hardwired system.
More information8061 IP Relay Controller FW Version Installation & Configuration
8061 IP Relay Controller FW Version 2.7.3 Installation & Configuration Order Codes 8061 IP Relay Controller Page 1 Table of Contents IMPORTANT SAFETY INFORMATION... 5 ABOUT THE ALGO 8061 IP RELAY CONTROLLER...
More informationMiVoice Office User Guide. MiVoice Office User Guide JANUARY 2019 DOCUMENT RELEASE USER GUIDE. Page 1
MiVoice Office 250-6900 User Guide MiVoice Office 250 6900 User Guide JANUARY 2019 DOCUMENT RELEASE 5.1 6900 USER GUIDE Page 1 MiVoice Office 250-6900 s NOTICE The information contained in this document
More informationAudio Integration Note
ELAN Home Systems Life Just Got Better Audio Integration Note Manufacturer: Elan Model Number(s): System 12 Comments: Version 5.0 (g!) requires S12 FW 2.02.00.04 Document Revision Date: 8/17/2011 OVERVIEW
More informationDMP 128 Plus C V DMP 128 Plus C V AT. ShoreTel Configuration Guide REVISION: DATE: DECEMBER 6 TH 2018
DMP 128 Plus C V DMP 128 Plus C V AT ShoreTel Configuration Guide REVISION: 1.1.1 DATE: DECEMBER 6 TH 2018 Revision Log Date Version Notes Sep. 21 st 2018 1.0 First Release: Applies to Firmware 1.01.0010
More informationSetting Up Lift Control For The First Time
Setting Up Lift Control For The First Time Introduction This tech guide will step you though the steps to set up the HikVision Lift Control to work with the Apartment IP Intercom Before you begin Ensure
More informationInstruction Manual WIZARD ELITE IP
Instruction Manual WIZARD ELITE IP Fasttel reserves the right to change the content of this manual without prior notice. Fasttel Belgium, Klipsenstraat 18A, 9160 Lokeren, Belgium. Tel. +32 (0)9 244 65
More informationGrandstream Networks, Inc. How to Integrate UCM6XXX with Microsoft Lync Server
Grandstream Networks, Inc. Table of Contents OVERVIEW... 4 UCM6XXX CONFIGURATION... 5 Step 1: Create SIP Peer Trunk... 5 Step 2: Configure Outbound Rule... 7 Step 3: Configure Inbound Rule... 8 MICROSOFT
More informationOwner s Manual. 1833, 1834, 1835, 1837 PC Programmable Telephone Entry and Access Control Systems
Owner s Manual 1833, 1834, 1835, 1837 PC Programmable Telephone Entry and Access Control Systems DoorKing, Inc. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Phone: 310-645-0023 Fax: 310-641-1586
More informationPhone Information. IP2061 Quick Reference Guide. ICON Voice Networks REV 1.0. ICON Voice Networks
Phone Information Extension Number: Passcode / Voice Mail Access Code: IP Address: MAC Address: Serial Number: REV 1.0 IP2061 Quick Reference Guide ICON Voice Networks 8001 Jetstar Drive Irving, TX 75063
More informationStainless steel Keys Direct-button 1 Numeric Keypad. Optional Microphone 1 Amplifier 1.5W. Adjustable FDSP. RTP CODEC G.711, G.
i20-t Door Phone 1 Description i20-t Voice Access control is a digital IP door phone with Fanvil Voip Solutions (Broadcom chip 1190), stable and reliable. FDSP ensure voice loud and clear. Good looking,
More informationUSER GUIDE FRONTROW CONDUCTOR VERSION
conductor USER GUIDE FRONTROW CONDUCTOR VERSION 1.3.3.1 YOU RE ABOUT TO IMPROVE COMMUNICATION THROUGHOUT YOUR SCHOOL AND DISTRICT. Welcome to FrontRow Conductor v1.3.3.1 FrontRow is the teacher- and tech-friendly
More informationAllworx Admin Update for 7.0
Allworx Admin Update for 7.0 No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopy, recording, or otherwise
More informationVideo Intercom for all your mobile devices iphone, ipad, ipod Touch and all Android phones and tablets!
Video Intercom for all your mobile devices iphone, ipad, ipod Touch and all Android phones and tablets! The doorbell rings, but you re not expecting visitors. With the new idor Mobile app, you can immediately
More informationAllowing access to Outlook 2000 folders Version 1.00
Allowing access to Outlook 2000 folders Version 1.00 Need to Know TM To allow another network user access to some or all of your Outlook folders you need to complete two processes. One in your Outlook
More informationSonicwall NSA220 / TZ215 / TZ300,400,500 Configuration Guide (Firmware: SonicOS Enhanced o & up)
SonicWALL Configuration Guide v1.8 Sonicwall NSA220 / TZ215 / TZ300,400,500 Configuration Guide (Firmware: SonicOS Enhanced 5.8.1.1-35o & up) 169 Saxony Road, Suite 212 Encinitas, CA 92024 Phone & Fax:
More informationCommPortal Communicator Desktop End User Guide 19 Feb 2014
End User Guide 19 Feb 2014 Integra Hosted Voice Service PC Communicator Desktop End User Guide 19 Feb 2014 21 Feb 20134 End User Guide Contents 1 Introduction... 1-1 1.1 Using this End User Guide... 1-2
More informationMinimum Core Module Versions: ELAN version 7.1 ( for streaming audio) MRA Software or above Document Revision Date: 6/9/2017
Manufacturer: SpeakerCraft Integration Note Model Number(s): MRA664 Minimum Core Module Versions: ELAN version 7.1 (8.1.398 for streaming audio) Comments: MRA Software 1.4.510 or above Document Revision
More informationIntegration Note. Virtual Matrix: The driver offers the ability to receive the auxiliary input feed from up to three other Sonos units
Integration Note Manufacturer: Sonos Model Number(s): Sonos PLAYBAR up to ver. 7.1 g! Core Module Version: 8.0.278 Driver Developer: Core Programming Limited Document Revision Date: 03/01/2017 OVERVIEW
More informationGrandstream Networks, Inc. Connecting GDS3710 with GXV3370 Configuration Guide
Grandstream Networks, Inc. Connecting GDS3710 with GXV3370 Configuration Guide Table of Contents INTRODUCTION... 3 PEERING SCENARIO... 4 Settings Configuration on the GDS3710 Side... 4 Settings Configuration
More informationSales Manual VIS. Contents. File: 2SM-VIS-v2.1 Ver: v2.1 Date:
Sales Manual VIS File: 2SM-VIS-v2.1 Ver: v2.1 Date: 2017.3.11 Contents Introduction... 2 System Blocks... 2 Key System Features... 3 IP39-70: SIP Android Control Monitor... 4 IP39-4x: SIP Video Access
More informationGrandstream Networks, Inc. Connecting GDS3710 with WP820 Configuration Guide
Grandstream Networks, Inc. Connecting GDS3710 with WP820 Configuration Guide Table of Contents INTRODUCTION... 3 PEERING SCENARIO... 4 Settings Configuration on the GDS3710 Side... 4 Settings Configuration
More informationInstallation Instructions
Installation Instructions For WiFi-Predator 1 P a g e Index Section Pages Android Configuration 3-6 iphone Configuration 7-10 Range and range testing 11-12 Installation 13 Power Supply 13 Wiring 14 Relay
More informationNetworked Door Strike Intermediate Relay Operation Guide
The IP Endpoint Company Networked Door Strike Intermediate Relay Operation Guide Part #011270 Document Part #931038C CyberData Corporation 3 Justin Court Monterey, CA 93940 (831) 373-2601 VoIP Outdoor
More informationTRBOnet Enterprise/PLUS
TRBOnet Enterprise/PLUS Phone Interconnect User Guide Version 5.2 World HQ Neocom Software 8th Line 29, Vasilyevsky Island St. Petersburg, 199004, Russia US Office Neocom Software 15200 Jog Road, Suite
More informationAny feature not specifically noted as supported is not supported.
Manufacturer: Model Number(s): Minimum Core Module Version: Document Revision Date: ELAN Integration Note EL-4KM-V44-KIT (Device Ver 3.06; Web Module Ver 6.20) EL-4KM-V88 (Device Ver 1.16; Web Module Ver
More informationDMP 128 Plus C V DMP 128 Plus C V AT. Cisco CUCM Configuration Guide REVISION: 1.1 DATE: SEPTEMBER 1 ST 2017
DMP 128 Plus C V DMP 128 Plus C V AT Cisco CUCM Configuration Guide REVISION: 1.1 DATE: SEPTEMBER 1 ST 2017 Revision Log Date Version Notes August 4 th 2017 1.0 First Release: Applies to Firmware Version
More informationDMP 128 Plus C V DMP 128 Plus C V AT. RingCentral Configuration Guide REVISION: 1.0 DATE: JUNE 26 TH 2018
DMP 128 Plus C V DMP 128 Plus C V AT RingCentral Configuration Guide REVISION: 1.0 DATE: JUNE 26 TH 2018 Revision Log Date Version Notes June 26 th 2018 1.0 First Release: Applies to Firmware 1.01.0010
More informationApplication notes for Algo 3226 Trunk Port FXO Doorphone with Avaya IP Office Release 7.0 Issue 1.0
Avaya Solution & Interoperability Test Lab Application notes for Algo 3226 Trunk Port FXO Doorphone with Avaya IP Office Release 7.0 Issue 1.0 Abstract These Application Notes describe the configuration
More informationConfiguring network settings for Suprema devices with firmware v2.x Download link: BioStar 2.x
Suprema devices IMPORTANT! Since version 3.3.859, CredoID works with a new Suprema SDK and therefore, no longer supports Suprema devices with firmware version v1.x and only supports firmware v2.x or devices
More informationPB-1-IP Panic Button / Silent alarm With Dialler and microphone for VoIP with PoE. Installation and user guide
PB-1-IP Panic Button / Silent alarm With Dialler and microphone for VoIP with PoE Installation and user guide Viking VoIP SIP System Compatibility List NOTE: Exclusion from this list means only that compatibility
More informationIntegration Note. Any feature not specifically noted as supported should be assumed to be unsupported.
Integration Note Manufacturer: Model Number(s): Roku All IP Controllable Roku Media Players g! Core Module Version: 8.0.278 Driver Developer: Core Programming Limited Document Revision Date: 03/01/17 Overview
More informationApplication Notes for Configuring Citel s Portico TVA with Avaya IP Office Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring Citel s Portico TVA with Avaya IP Office Issue 1.0 Abstract These Application Notes describe the configuration steps required
More informationFREUND SIP SW - V SIP-server setup
FREUND SIP SW - V1.7.13 SIP-server setup Content 1. Product Setup 4 2. Log in and Home 5 3. Menu 9 3.1 Tools 9 3.1.1 Dashboard 9 3.1.2 Extensions 10 3.1.3 Trunks 14 3.1.4 Groups 18 3.1.5 Ring groups 20
More informationSI IP Door Station. Quick Start Guide
SI-8000 IP Door Station Quick Start Guide Table of Contents Introduction Dimensions... 1 Basic Network Connections... 2 RJ-45 Pinout... 2 Pre-install Volume Adjustment... 2 1. Detect & Verify Network Settings...
More informationCenturyLink Business Communicator for Desktop
CenturyLink Business Communicator for Desktop User Guide Release 2.0 Document Version 4 BusinessCommunicator_Guide_0517_v4 1 CenturyLink Business Communicator Guide Table of Contents 1 About CenturyLink
More informationHMIQDHDD Transmitter Firmware Revision Release Notes August 4th 2010 HMIQDHDD
HMIQDHDD Transmitter Firmware Revision 4.0.0.0 Release Notes August 4 th 2010 This document outlines: 1. HMIQDHDD Transmitter System Firmware Version and Compatibility 2. Important Installation Notes 3.
More informationEXP38 User Manual Yealink Network Technology Co. Ltd. All rights reserved. Version 41.0
EXP38 User Manual 2009 Yealink Network Technology Co. Ltd. All rights reserved. Version 41.0 www.yealink.com About This Guide This Expansion Module EXP38 is designed for connection of the Yealink Enterprise
More informationBell Commander/Shoretel Server and Multicast Configuration Guide
The IP Endpoint Company Bell Commander/Shoretel Server and Multicast Configuration Guide Document Part #930488A CyberData Corporation 3 Justin Court Monterey, CA 93940 (831) 373-2601 Bell Commander/Shoretel
More informationSV9100 SIP Trunking Service Configuration Guide for Cable ONE Business
SV9100 SIP Trunking Service Configuration Guide for Cable ONE Business NDA-31871 Issue 1.0 NEC Enterprise Communication Technologies, Inc. reserves the right to change the specifications, functions, or
More information