Calipers Height Gauges Depth Gauges

Transcription

1 Calipers Height Gauges epth Gauges Calipers Height Gauges epth Gauges CONTENTS Calipers IP67 Solar SuperCaliper -3 IP67 Caliper -5 Caliper -7 Long Beam Caliper -9 Solar Caliper -10 Vernier Caliper -11 Vernier Thumbwheel Caliper -13 Vernier Thumb Clamp Caliper -14 IP67 Nib Jaw Caliper -15 IP67 Nib/Standard Jaw Caliper -16 ial Caliper -17 IP66 Carbon Fibre Caliper -19 IP66 Long Jaw Carbon Fibre Caliper -21 IP66 Ceramic Jaw Carbon Fibre Caliper -22 IP66 Interchangeable Jaw Carbon Fibre Caliper -23 Vernier Nib Jaw Thumbwheel Caliper -25 Vernier Long Jaw Thumbwheel Caliper -26 IP67 Offset Jaw Calipers -27 IP67 Offset Centreline Calipers -28 Back Jaw Centreline Caliper -29 IP67 Point Calipers -30 IP67 Blade Type Calipers -31 IP67 Knife Edge Inside Calipers -32 IP67 Inside Groove Calipers -33 IP67 Point Jaw Inside Calipers -34 IP67 Neck Jaw Calipers -35 IP67 Tube Thickness Calipers -36 Vernier Hook Jaw Caliper -37 Vernier Moving Jaw Caliper -38 Low Force Caliper -39 Snap Caliper -40 Quick Guide to Calipers -41 Height Gauges Multifunction Height Gauge -45 ouble Column Height Gauge -47 Ergonomic Height Gauge -49 Height Gauge -50 Vernier djustable Scale Height Gauge -51 Mechanical Counter Height Gauge -52 Optional ccessories -53 Linear Height 2 Measurement System -55 QM-Height High Precision Height Gauge -57 Quick Guide to Height Gauges -59 epth Gauges Interchangeable Rod epth Micrometers -61 epth Micrometer -63 IP67 epth Gauge -64 epth Gauge -65 Vernier epth Gauge -66 IP67 Hook End epth Gauge -67 ial Fine djustment epth Gauge -68 ial epth Gauges -69 epth Gauge -70 Optional ccessories -71-2

2 Calipers SERIES 500 BSOLUTE igimatic Coolant Proof Solar SuperCaliper Top-of-the-line digital caliper. Solar type caliper with no battery and IP67 protection assures waterproof reliability. With no annoying origin restoration necessary, a measurement can be started any time and there is no restriction on operating speed. Insufficient illumination Sufficient illumination mm No need for origin set up SPC data output models can be integrated into statistical process control and measurement systems Slider operation is smooth and comfortable. The impact resistance of the display unit has been increased for improved usability in workshop conditions. Waterproof function makes this SuperCaliper suitable for use in an environment containing large amounts of cutting fluid or coolant. Operability is equivalent to the mechanical type caliper. This SuperCaliper uses components that do not contain harmful substances and is compatible with RoHS irectives Technical ata Repeatability: 0.01 mm Quantizing error: ±1 count ust/water protection level: IP67* 2 Power supply: Solar cell* 3 Scale type: BSOLUTE electromagnetic induction linear encoder * 2 Rustproofing treatment to be applied after use. * 3 Can be used continuously above 60 lux ambient illumination. Functions BSOLUTE system measurement: fter power is turned ON, measurement can be started without zero-setting if origin-setting was previously performed. The BS (absolute) origin position can be changed by the ORIGIN button. Zero-setting (INC measurement mode): isplayed value can be set to zero at any arbitrary position of the slider for comparative measurements. ata output: Models equipped with this function have an output port for transferring measurement data to a Statistical Process Control (SPC) system. Inch/mm selection: Switches the units of measurement (at any time). lerts: If the ambient illumination and the stored charge voltage are insufficient an error message is displayed and measurement stops. If contamination on the surface of the scale causes a calculation error, an error message is displayed and measurement stops. Code No. Range Resolution ccuracy* 1 Mass With SPC data output mm (0-6") 180 g 0.01 mm (.0005") ±0.02 mm mm (0-8") 210 g Without SPC data output mm (0-6") 180 g 0.01 mm (.0005") ±0.02 mm mm (0-8") 210 g * 1 Excluding quantizing error. IMENSIONS C Smooth slider movement makes for comfortable operation. High quality guide surface finish for smooth slider movement. E B Conventional SuperCaliper Ra: μm Ra: 0.07 μm Range B C E mm mm Jaw thickness: 3.5 mm -3

3 bout the charge function The minimum illumination required in the uncharged state is 60 lux. s shown in the table at right, this SuperCaliper can be used with confidence in a normal work environment. The charge function allows the operator to use the SuperCaliper without interrupting work even if the ambient illumination is temporarily insufficient. In the fully charged state this SuperCaliper can operate for approximately one hour in an environment of 50 lux illumination (less than the minimum necessary illumination intensity). The time necessary for full charge varies according to the charging conditions. If the SuperCaliper is left unused in an illumination of 500 lux (usual for manufacturing environments), it takes approximately one hour to reach full charge. Illumination (lx) Site (possible operations) 1500 esign room, drafting room 1000 (Fine visual work) 750 Conference room, control room 500 (Usual manufacturing environment) (Normal visual work) 300 Machine room, electric room, lecture hall 200 (Rough visual work) 150 Corridor, passage, stairs 100 (Very rough visual work) Emergency staircase, warehouse 30 (Loading, unloading work) 20 Excerpts from JIS Z 9110 rtificial Illumination Intensity Standard ir leak test equipment for water resistance inspection Generally, an air leak test is used for evaluating water resistance. Procedure: Place the measuring tool inside the capsule and seal it. Then fill the capsule and the test chamber with air at the required pressure and close the isolating valves. If there is no leak in the measuring tool, the differential pressure sensor will read zero, because the amount of air inside the test chamber is unchanging. However, if there is a leak in the measuring tool, the differential pressure sensor will show a non-zero reading due to a decrease in pressure inside the test chamber as air leaks into the tool. By detecting this differential pressure, GO/NG judgement for the severity of the leak is performed. This air leak test is performed for all coolant proof calipers and coolant proof micrometers. ir supply Isolating valves Isolating valves Capsule ifferential pressure sensor Test chamber ir leak test equipment for coolant proof caliper -4

4 Calipers SERIES 500 BSOLUTE igimatic Coolant Proof Caliper Can be used in workshop conditions exposed to coolant, water, dust or oil. Other specifications and price are the same as the conventional products. 100% inspection by air leak test is performed to ensure quality and reliability. Large LC characters make the display easy to read. Easy to use advanced design styling with only 1 button. Incorporates Mitutoyo's BSOLUTE measurement system. No need to reset the origin. SPC data output models can be integrated into statistical process control and measurement systems. Can measure outside and inside dimensions, depth, and steps. The automatic power-on/off function shuts down the LC display after 20 minutes inactivity, but the BS scale unit origin is stored. Power is restored when the slider is moved. convenient interface input tool is available so that measurement data can be converted to keyboard signals and input directly to commercial spreadsheet software. n inspection certificate is supplied as standard. (However, this cannot be used as a calibration certificate as it is undated.) Technical ata Resolution: 0.01 mm (.0005") Repeatability: 0.01 mm Quantizing error: Not including ±1 count ust/water protection level: IP67* 1 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use (1 year: over 300 mm models) * 1 Rustproofing treatment to be applied after use. Functions BSOLUTE system measurement: fter power is turned ON, measurement can be started without zero-setting if origin-setting was previously performed. The BS (absolute) origin position can be changed by the ORIGIN button. Zero-setting (INC measurement mode): isplayed value can be set to zero at any arbitrary position of the slider for comparative measurements. uto ON/OFF: The reading on the LC disappears after this instrument is idle for a short time, but the origin point is retained. Moving the slider causes the reading on the LC to reappear. ata output: Models equipped with this function have an output port for transferring measurement data to a Statistical Process Control (SPC) system. Inch/mm selection: Switches the units of measurement (at any time). lerts: In the unlikely event of a display overflow or calculation error, an error message is displayed and measurement stops. Measurement cannot continue until the error is corrected. If the battery voltage drops below a certain point, the battery indicator will turn on before measurement becomes impossible, warning the user that the battery needs to be replaced. If contamination on the surface of the scale causes a calculation error, an error message is displayed and measurement stops. IMENSIONS C B E Range B C E mm mm mm Outside jaw thickness: 3.5 mm ( : 3.8 mm) -5

5 Smooth slider movement makes for comfortable operation. High quality guide surface finish for smooth slider movement. Conventional Ra: μm Coolant Proof Caliper Ra: 0.07 μm Code No. Range ccuracy* 2 Remarks With SPC data output mm Carbide-tipped jaws for outside measurement (0-6") ±0.02 mm Carbide-tipped jaws for outside and inside measurement (.001") mm Carbide-tipped jaws for outside measurement (0-8") Carbide-tipped jaws for outside and inside measurement mm (0-12") Without SPC data output mm (0-6") ±0.03 mm (.0015") Carbide-tipped jaws for outside measurement ±0.02 mm Carbide-tipped jaws for outside and inside measurement (.001") mm Carbide-tipped jaws for outside measurement (0-8") Carbide-tipped jaws for outside and inside measurement mm ±0.03 mm (0-12") (.0015") * 2 Excluding quantizing error. Carbide-tipped jaws for outside measurement Carbide-tipped jaws for inside measurement -6

6 Calipers SERIES 500 BSOLUTE igimatic Caliper The ZERO/BS button allows the display to be Zero-Set at any slider position along the scale for comparison measurements. This button will also allow return to the absolute (BS) mode and display of the true position from the origin (usually jaws closed point). Large and clear LC readout. Smooth slider movement makes for comfortable operation. 20,000 hours battery life. Can measure outside and inside dimensions, depth, and steps. Carbide-tipped jaw calipers give the longest life when measuring rough finished parts, castings, grinding wheels, etc. ata output function allows integration into statistical process control and measurement systems Technical ata Resolution: 0.01 mm (.0005") Repeatability: 0.01 mm Scale type: BSOLUTE electrostatic linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3.5 years under normal use (20,000 hours for continuous use) Functions bsolute measurement: fter power is turned ON, measurement can be started without zero-setting if origin-setting was previously performed. The bsolute origin position can be changed by the ORIGIN button. Incremental measurement: isplay can be set to zero at any arbitrary position for comparative measurements. Scale contamination detection: Contamination on the surface of the scale is detected and an error message (ErrC) is displayed. Low-voltage alert: If the battery voltage becomes low, a B appears in the display to alert the user before measurement is no longer possible. battery change advisory alert precedes this alert. ata output: Models equipped with this function have an output port for transferring measurement data to a Statistical Process Control (SPC) system. ata hold: By using the data hold unit (option), the displayed value can be held. This cannot be used with the data output function IMENSIONS C : ata hold unit E B Range B C E mm mm mm

7 Smooth slider movement makes for comfortable operation. High quality guide surface finish for smooth slider movement. Conventional Ra: μm BSOLUTE igimatic Caliper Ra: μm Code No. Range ccuracy* 2 Remarks With SPC data output mm Carbide-tipped jaws for outside measurement (0-6") ±0.02 mm Carbide-tipped jaws for outside and inside measurement (.001") mm Carbide-tipped jaws for outside measurement (0-8") Carbide-tipped jaws for outside and inside measurement mm ±0.03 mm Carbide-tipped jaws for outside measurement (0-12") (.0015") Carbide-tipped jaws for outside and inside measurement Without SPC data output mm Carbide-tipped jaws for outside measurement (0-6") ±0.02 mm Carbide-tipped jaws for outside and inside measurement (.001") mm Carbide-tipped jaws for outside measurement (0-8") Carbide-tipped jaws for outside and inside measurement mm ±0.03 mm Carbide-tipped jaws for outside measurement (0-12") (.0015") Carbide-tipped jaws for outside and inside measurement * 2 Excluding quantizing error. Carbide-tipped jaws for outside measurement Carbide-tipped jaws for inside measurement -8

8 Calipers SERIES 500 BSOLUTE igimatic Long Beam Caliper Long igimatic caliper incorporating Mitutoyo's BSOLUTE scale and available with a measuring range from 450 mm to 1000 mm. Can measure outside and inside dimensions, depth, and steps. ata output function allows integration into statistical process control and measurement systems. Technical ata Scale type: BSOLUTE electrostatic linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3.5 years under normal use (20,000 hours for continuous use) : ata hold unit Code No. Range Resolution ccuracy* Repeatability mm (0-18") ±0.05 mm (±.002") mm (0-24") 0.01 mm (.0005") 0.01 mm mm (0-40") ±0.07 mm (±.003") * Excluding quantizing error. IMENSIONS C B Range B C Measuring surface thickness mm mm mm

9 Technical ata Scale type: BSOLUTE electrostatic linear encoder Power supply: Solar cell* 1 Operational temperature: 0 to 40 C * 1 Can be used continuously above 60 lux ambient illumination Functions BSOLUTE system measurement: fter power is turned ON, measurement can be started without zero-setting if origin-setting was previously performed. The BS (absolute) origin position can be changed by the ORIGIN button. Zero-setting (INC measurement mode): isplayed value can be set to zero at any arbitrary position of the slider for comparative measurements. ata output: Models equipped with this function have an output port for transferring measurement data to a Statistical Process Control (SPC) system. ata hold: By using the data hold unit (option), the displayed value can be held. This cannot be used with the data output function. Inch/mm selection: Switches the units of measurement (at any time). lerts: In the unlikely event of a display overflow or calculation error, an error message is displayed and measurement stops. Measurement cannot continue until the error is corrected. If contamination on the surface of the scale causes a calculation error, an error message is displayed and measurement stops. SERIES 500 BSOLUTE igimatic Solar Caliper Mitutoyo's bsolute Solar igimatic Caliper retains its origin point indefinitely. t 60 Lux and above the BSOLUTE solar caliper is ready to start measurement. No more repeated zero setting caused by a shortage of light. Can measure outside and inside dimensions, depth, and steps. Slider operation is smooth and comfortable. n BSOLUTE scale is incorporated so that zero setting is not required at each power ON. No danger of overspeed errors. llows integration into statistical process control and measurement systems for models with measurement data output connector Code No. Range Resolution ccuracy* Repeatability With SPC data output mm (0-6") mm (0-8") 0.01 mm (.0005") ±0.02 mm (±.001") 0.01 mm Without SPC data output mm (0-6") mm (0-8") 0.01 mm (.0005") ±0.02 mm (±.001") 0.01 mm * Excluding quantizing error. IMENSIONS E B C : ata hold unit Range B C E mm mm Smooth slider movement makes for comfortable operation. High quality guide surface finish for smooth slider movement. Conventional BSOLUTE Solar Caliper Ra: μm Ra: μm -10

10 Calipers SERIES 530 Vernier Caliper Stepped graduation face prevents dust ingress between the main scale and slider. The small vernier face angle (14 ) provides easy reading. Can measure outside and inside dimensions, depth, and steps. Carbide-tipped jaw calipers give the longest life when measuring rough finished parts, castings, grinding wheels, etc. ecimal and fractional graduated scales (metric/inch and inch models only) (Round rod depth bar type) (Carbide-tipped jaw type) 14 IMENSIONS E B G C F Range B C E F G Outside jaw thickness mm mm mm mm mm mm * Code No incorporates a round rod depth bar (ø1.9 mm). The depth bar shown above is a blade type. -11

11 Metric Code No. Range ccuracy Graduation epth bar Remarks ø1.9 mm rod mm ±0.05 mm Carbide-tipped jaws for outside measurement mm Blade Carbide-tipped jaws for outside mm measurement ±0.08 mm mm Carbide-tipped jaws for outside measurement mm ±0.1 mm mm ±0.15 mm Code No. Range ccuracy Graduation epth bar Remarks mm ±0.05 mm 0.05 mm (1/128") (0-6") ±0.03 mm 0.02 mm (.001") High accuracy model mm (0-8") ±0.03 mm 0.02 mm (.001") Blade High accuracy model: ±0.03 mm mm ±0.08 mm 0.05 mm (1/128") (0-12") ±0.04 mm 0.02 mm (.001") High accuracy model: ±0.04 mm Measurement pplications 1. Outside measurement 2. Inside measurement 3. Step measurement 4. epth measurement -12

12 Calipers SERIES 532 Vernier Thumbwheel Caliper Fine-adjustment thumbwheel aids slider positioning. Can measure outside and inside dimensions, depth, and steps. Fine adjustment thumbwheel Metric Code No. Range ccuracy Graduation mm ±0.03 mm mm 0.02 mm mm ±0.04 mm Code No. Range ccuracy Graduation mm (0-5") ±0.03 mm mm (0-7") 0.02 mm (.001") mm (0-11") ±0.04 mm IMENSIONS C E B G F Range B C E F G mm mm mm

13 SERIES 531 Vernier Thumb Clamp Caliper The slider moves only when the spring-loaded thumb clamp is depressed. Can measure outside and inside dimensions, depth, and steps. Spring-loaded thumb grip Metric Code No. Range ccuracy Graduation Remarks mm ±0.05 mm mm 0.05 mm mm ±0.08 mm Code No. Range ccuracy Graduation Remarks mm (0-6") ±0.03 mm mm (0-8") 0.02 mm (.001") High accuracy model mm (0-12") ±0.04 mm IMENSIONS L B C Range L B C mm mm mm

14 Calipers SERIES 550 BSOLUTE igimatic Coolant Proof Nib Jaw Caliper Offers a resolution of 0.01 mm with corresponding accuracy. Incorporates Mitutoyo's BSOLUTE measurement system. No need to reset the origin after switching on. Models and are IP67 rated. ata output function allows integration into statistical process control and measurement systems. I measurement value: displayed value + (the minimum inside measurement value mentioned below). OFFSET button automatically adds the thickness of the inside jaws to the measured value so that the result can be read directly ( and ). Preset function enables an arbitrary reference value to be added to the measured value for comparison measurements ( ). Technical ata Resolution: 0.01 mm (.0005") Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use (1 year: over 300 mm models, 3.5 years: over 300 mm models) ust/water protection level: IP67* 3 (models up to 300 mm) * 3 Rustproofing treatment to be applied after use. Optional ccessories : ata hold unit Code No. Range* 1 ccuracy* 2 Remarks mm / 0-8" ( mm /.4-8.4") ±0.03 mm / ±.0015" IP mm / 0-12" IP67, with offset/preset function for easy ( mm / ") inside measurement mm / 0-18" ( mm / ") ±0.05 mm / ±.002" mm / 0-24" ( mm / ") mm / 0-40" ( mm / 1-41") ±0.07 mm / ±.003" * 1 ( ): Inside measurement. * 2 Excluding quantizing error. Note: Series 550 is not equipped with a depth bar. IMENSIONS Radiused jaws for accurate I measurement R B C Range B C R mm mm mm mm mm

15 SERIES 551 BSOLUTE igimatic Coolant Proof Nib/Standard Jaw Caliper Technical ata Resolution: 0.01 mm (.0005") Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use (1 year: over 300 mm models, 3.5 years: over 300 mm models) ust/water protection level: IP67* 3 (models up to 300 mm) * 3 Rustproofing treatment to be applied after use. Offers a resolution of 0.01 mm with corresponding accuracy. Incorporates Mitutoyo's BSOLUTE measurement system. No need to reset the origin after switching on. ata output function allows integration into statistical process control and measurement systems. I measurement value: displayed value + (the minimum inside measurement value mentioned below). OFFSET button automatically adds the thickness of the inside jaws to the measured value so that the result can be read directly ( and ). Preset function enables an arbitrary reference value to be added to the measured value for comparison measurements ( ). Tips of the outside measurement jaw are relieved for easy measurement of thin parts. Optional ccessories : ata hold unit Radiused jaws for accurate I measurement Code No. Range* 1 ccuracy* 2 Remarks mm / 0-8" ( mm /.4-8.4") ±0.03 mm / ±.0015" IP mm / 0-12" IP67, with offset/preset function for easy ±0.04 mm / ±.002" ( mm / ") inside measurement mm / 0-20" ( mm / ") ±0.06 mm / ±.0025" mm / 0-30" ( mm / ") mm / 0-40" ( mm / 1-41") ±0.07 mm / ±.003" * 1 ( ): Inside measurement. * 2 Excluding quantizing error. Note: Series 550 is not equipped with a depth bar. IMENSIONS B C Range B C mm mm mm mm mm 20-16

16 Calipers SERIES 505 ial Caliper Newly designed dial movement for ultra-smooth sliding and high shock protection. Titanium coating is applied to the sliding surfaces to enhance durability (except for mm and 0-12" model). Easy-to-read yellow dial. Large finger rest aids ease of use. Jaw tips are relieved for easy measurement of thin parts. Can measure outside and inside dimensions, depth, and steps. Wear comparison of main scale slider face Following photos show the condition of sliding surfaces after a sliding test comprising 100,000 movements. Smooth movement over the entire measuring range is assured even when you use a particular part of the sliding surface repeatedly Titanium coating Conventional Wear: 0 μm Wear: 4 μm IMENSIONS E G B F C Range B C E F G mm mm mm

17 Metric Code No. Range ccuracy Graduation Remarks ±0.03 mm 0.02 mm, 2 mm/rev Carbide-tipped jaws for outside measurement mm Carbide-tipped jaws for outside and inside measurement ±0.02 mm 0.01 mm, 1 mm/rev Silver cover type mm, 2 mm/rev mm ±0.03 mm mm, 1 mm/rev mm ±0.04 mm 0.02 mm, 2 mm/rev Inch Code No. Range ccuracy Graduation Remarks " ±.001" Carbide-tipped jaws for outside measurement Carbide-tipped jaws for outside and inside measurement ",.1"/rev Silver cover type 0-8" Carbide-tipped jaws for outside measurement Carbide-tipped jaws for outside and inside measurement ",.2"/rev ±.002" ",.1"/rev Silver cover type Carbide-tipped jaws for outside ",.2"/rev measurement 0-12" Carbide-tipped jaws for outside measurement, silver cover type.001",.1"/rev Carbide-tipped jaws for outside and inside measurement, silver cover type -18

18 J Calipers SERIES 552 BSOLUTE igimatic Coolant Proof Carbon Fibre Caliper lightweight igimatic caliper that uses CFRP (Carbon Fibre Reinforced Plastics) in the beam and jaws. Interchangeable measuring jaws available as optional accessories. ata output function allows integration into statistical process control and measurement systems. Technical ata Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 5,000 hours in continuous use ust/water protection level: IP66* 3 Standard accessory: Jaw clamps (2 pcs.), 05GZ033 * 3 Rustproofing treatment to be applied after use. Functions Code No. Range* 1 Resolution ccuracy* (20) mm / 0 (.5") - 18" (20) mm / 0 (.5") - 24" ±0.04 mm / ±.002" (20) mm / 0 (1") - 40" 0.01 mm /.0005" ±0.05 mm / ±.003" (20) mm / 0 (1") - 60" ±0.09 mm / ±.004" (20) mm / 0 (1") - 80" ±0.12 mm / ±.005" * 1 ( ): Minimum dimension in inside measurement. * 2 Excluding quantizing error. IMENSIONS F E BSOLUTE system measurement: fter power is turned ON, measurement can be started without zero-setting if origin-setting was previously performed. The BS (absolute) origin position can be changed by the ORIGIN button. Zero-setting (INC measurement mode): isplayed value can be set to zero at any arbitrary position of the slider for comparative measurements. uto ON/OFF: The reading on the LC disappears after this instrument is idle for a short time, but the origin point is retained. Moving the slider causes the reading on the LC to reappear. ata output: Models equipped with this function have an output port for transferring measurement data to a Statistical Process Control (SPC) system. ata hold: By using the data hold unit (option), the displayed value can be held. This cannot be used with the data output function. Presetting (BS INC measurement mode): isplayed value can be set to any arbitrary value. Offsetting: utomatically adds the thickness of the inside jaws to the measured value so that the result can be read directly, without calculation. Inch/mm selection: Switches the units of measurement (at any time). lerts: In the unlikely event of a display overflow or calculation error, an error message is displayed and measurement stops. Measurement cannot continue until the error is corrected. If the battery voltage drops below a certain point, the battery indicator will turn on before measurement becomes impossible, warning the user that the battery needs to be replaced. If contamination on the surface of the scale causes a calculation error, an error message is displayed and measurement stops. C H B G L L K Range B C E F G H J K L mm mm mm R mm mm

19 Optional ccessories Code No. escription Suitable for Clamp (1 pair) , , and Clamp (1 pair) , and Centre-to-Centre jaws (1 pair) , , , , Point jaws , and Clamp Centre-to-Centre jaws Centre-to-Centre jaws ccuracy: ±0.03 mm 10 Point jaws ccuracy: ±0.02 mm ø1 Point jaws 50 ø1-20

20 B8 Calipers SERIES 552 BSOLUTE igimatic Long Jaw Carbon Fibre Caliper lightweight igimatic caliper that uses CFRP (Carbon Fibre Reinforced Plastics) in the beam and jaws. ata output function allows integration into statistical process control and measurement systems. Technical ata Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 5,000 hours in continuous use ust/water protection level: IP66* 3 Standard accessory: Jaw clamps (2 pcs.), 05GZ033 * 3 Rustproofing treatment to be applied after use. Functions Code No. Range* 1 Resolution ccuracy* (20) mm / 0 (.5") - 18" (20) mm / 0 (.5") - 24" ±0.06 mm / ±.0025" (20) mm / 0 (1") - 40" 0.01 mm /.0005" ±0.07 mm / ±.003" (20) mm / 0 (1") - 60" ±0.11 mm / ±.0045" (20) mm / 0 (1") - 80" ±0.14 mm / ±.0055" * 1 ( ): Minimum dimension in inside measurement. * 2 Excluding quantizing error. IMENSIONS C E G H BSOLUTE system measurement: fter power is turned ON, measurement can be started without zero-setting if origin-setting was previously performed. The BS (absolute) origin position can be changed by the ORIGIN button. Zero-setting (INC measurement mode): isplayed value can be set to zero at any arbitrary position of the slider for comparative measurements. uto ON/OFF: The reading on the LC disappears after this instrument is idle for a short time, but the origin point is retained. Moving the slider causes the reading on the LC to reappear. ata output: Models equipped with this function have an output port for transferring measurement data to a Statistical Process Control (SPC) system. ata hold: By using the data hold unit (option), the displayed value can be held. This cannot be used with the data output function. Presetting (BS INC measurement mode): isplayed value can be set to any arbitrary value. Offsetting: utomatically adds the thickness of the inside jaws to the measured value so that the result can be read directly, without calculation. Inch/mm selection: Switches the units of measurement (at any time). lerts: In the unlikely event of a display overflow or calculation error, an error message is displayed and measurement stops. Measurement cannot continue until the error is corrected. If the battery voltage drops below a certain point, the battery indicator will turn on before measurement becomes impossible, warning the user that the battery needs to be replaced. If contamination on the surface of the scale causes a calculation error, an error message is displayed and measurement stops. F 24 R10 8 Range B C E F G H mm mm mm mm mm

21 J Technical ata Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 5,000 hours in continuous use ust/water protection level: IP66* 3 Standard accessory: Jaw clamps (2 pcs.), 05GZ033 * 3 Rustproofing treatment to be applied after use. SERIES 552 BSOLUTE igimatic Coolant Proof Ceramic Jaw Carbon Fibre Caliper lightweight igimatic caliper that uses CFRP (Carbon Fibre Reinforced Plastics) in the beam and jaws. Rustless and nonmagnetic. Suitable for measuring magnetic components. Zirconia ceramic contact surfaces for high resistance to wear.. ata output function allows integration into statistical process control and measurement systems. Functions BSOLUTE system measurement: fter power is turned ON, measurement can be started without zero-setting if origin-setting was previously performed. The BS (absolute) origin position can be changed by the ORIGIN button. Zero-setting (INC measurement mode): isplayed value can be set to zero at any arbitrary position of the slider for comparative measurements. uto ON/OFF: The reading on the LC disappears after this instrument is idle for a short time, but the origin point is retained. Moving the slider causes the reading on the LC to reappear. ata output: Models equipped with this function have an output port for transferring measurement data to a Statistical Process Control (SPC) system. ata hold: By using the data hold unit (option), the displayed value can be held. This cannot be used with the data output function. Presetting (BS INC measurement mode): isplayed value can be set to any arbitrary value. Offsetting: utomatically adds the thickness of the inside jaws to the measured value so that the result can be read directly, without calculation. Inch/mm selection: Switches the units of measurement (at any time). lerts: In the unlikely event of a display overflow or calculation error, an error message is displayed and measurement stops. Measurement cannot continue until the error is corrected. If the battery voltage drops below a certain point, the battery indicator will turn on before measurement becomes impossible, warning the user that the battery needs to be replaced. If contamination on the surface of the scale causes a calculation error, an error message is displayed and measurement stops. Code No. Range* 1 Resolution ccuracy* (20) mm / 0 (.5") - 18" (20) mm / 0 (.5") - 24" 0.01 mm /.0005" ±0.04 mm / ±.002" * 1 ( ): Minimum dimension in inside measurement. * 2 Excluding quantizing error. IMENSIONS F C H B E G 10(.25) 10(.25) K Range B C E F G H J K mm R mm 790 * 4 Refer to page -20 for details. -22

22 Calipers SERIES 552 BSOLUTE igimatic Coolant Proof Interchangeable Jaw Carbon Fibre Caliper lightweight igimatic caliper that uses CFRP (Carbon Fibre Reinforced Plastics) in the beam and jaws. Provided with preset function for setting a desired starting point, which allows direct readout of offset measurement. The range of applications can be expanded by using interchangeable jaws (optional). ata output function allows integration into statistical process control and measurement systems. Code No. Range* 1 Resolution ccuracy* mm / 0-18" mm / 0-24" ±0.04 mm / ±.002" mm / 0-40" 0.01 mm /.0005" mm / 0-60" ±0.09 mm / ±.004" mm / 0-80" ±0.12 mm / ±.005" * 1 Excluding quantizing error. pplication examples Surface plate type and standard type Surface plate type Optional interchangeable jaws Standard type (right) Scriber type Scriber type (left) Scriber type (right) Scriber (arc) Technical ata Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 5,000 hours in continuous use ust/water protection level: IP66* 2 Standard accessory: Jaw clamps (2 pcs.), 05GZ033 * 2 Rustproofing treatment to be applied after use. Functions BSOLUTE system measurement: fter power is turned ON, measurement can be started without zero-setting if origin-setting was previously performed. The BS (absolute) origin position can be changed by the ORIGIN button. Zero-setting (INC measurement mode): isplayed value can be set to zero at any arbitrary position of the slider for comparative measurements. uto ON/OFF: The reading on the LC disappears after this instrument is idle for a short time, but the origin point is retained. Moving the slider causes the reading on the LC to reappear. ata output: Models equipped with this function have an output port for transferring measurement data to a Statistical Process Control (SPC) system. ata hold: By using the data hold unit (option), the displayed value can be held. This cannot be used with the data output function. Presetting (BS INC measurement mode): isplayed value can be set to any arbitrary value. Offsetting: utomatically adds the thickness of the inside jaws to the measured value so that the result can be read directly, without calculation. Inch/mm selection: Switches the units of measurement (at any time). lerts: In the unlikely event of a display overflow or calculation error, an error message is displayed and measurement stops. Measurement cannot continue until the error is corrected. If the battery voltage drops below a certain point, the battery indicator will turn on before measurement becomes impossible, warning the user that the battery needs to be replaced. If contamination on the surface of the scale causes a calculation error, an error message is displayed and measurement stops. Inside point type Surface plate type and scriber for height gauges ch Scriber for height gauges Inside point type Surface plate type Surface plate type and centreline type Centreline type Surface plate type -23

23 Interchangeable Jaw imensions Standard type 9 b a Inside point type Interchangeable Jaw Specifications Code No. Components a b Price Standard type 07CZ056* 2 pcs. 28 mm 30 mm Inside point type 07CZ058* 2 pcs. 25 mm 50 mm CZ059* 2 pcs. 1" 2" Scriber type 07CZ055* 2 pcs. 8 mm 30 mm CZ061* 2 pcs..031" 1.2" * Individual components available, price on application. Code No. Components a b Price Surface plate type 07CZ044 1 pc. 90 mm 28 mm Centreline type 07CZ057* 2 pcs. 30 mm 30 mm CZ060* 2 pcs. 1.2" 1.2" Scriber for height gauges 07GZ000 1 pc * Individual components available, price on application. Scriber type Surface plate type b Centreline type 30 8 b b 33 a 5 øa a Scriber for height gauges b ø1 øa R Interchangeable Jaw pplicable calipers Range ccuracy when attached to the caliper mm ( 0-18") mm ( 0-24") ±0.06 mm (±.0025") Standard type mm ( 0-40") ±0.07 mm (±.0030") mm ( 0-60") ±0.11 mm(±.0045") mm (0-80") ±0.14 mm (±.0055") Inside: mm (2-20") Outside: mm (0-18") Inside: mm (2-26") Outside: mm (0-24") ±0.09 mm(±.0035") Inside point type Inside: mm (2-42") Outside: mm (0-40") ±0.10 mm (±.0040") Inside: mm (2-62") Outside: mm (0-60") ±0.14 mm (±.0055") Inside: mm(2-82") Outside: mm( 0-80") ±0.17 mm (±.0070") mm ( ") mm ( ") ±0.08 mm (±.0030") Centreline type mm ( ") ±0.09 mm (±.0035") mm ( ") ±0.13 mm(±.0055") mm ( ") ±0.16 mm (±.0065") mm ( ") mm ( ") ±0.10 mm (±.0040") Scriber type mm ( ") ±0.11 mm (±.0045") mm ( ") ±0.15 mm (±.0060") mm ( ") ±0.18 mm (±.0070") mm (0-17.7") Surface plate type and mm (0-23.7") ±0.10 mm(±.0040") scriber type for height mm (0-39.4") ±0.11 mm (±.0045") gauges mm (0-59.4") ±0.15 mm (±.0060") mm (0-79.6") ±0.18 mm (±.0070") Inside: mm (1-19") Outside: mm (1-18") Inside: mm (1-25") Outside: mm (1-24") ±0.12 mm (±.0050") Surface plate type and Inside: mm (1-41") inside point type Outside: mm (1-40") ±0.13 mm (±.0055") Inside: mm (1-62") Outside: mm (1-60") ±0.17 mm (±.0070") Inside: mm (1-81") Outside: mm (1-80") ±0.20 mm (±.0080") mm ( ") Surface plate type and centreline type mm ( ") ±0.11 mm (±.0045") mm ( ") ±0.12 mm (±.0050") mm ( ") ±0.16 mm (±.0065") mm ( ") ±0.19 mm (±.0075") -24

24 Calipers SERIES 160 Vernier Nib Jaw Thumbwheel Caliper Inside and outside measurements can be read directly from the upper and lower vernier scales. The jaws have radiused measuring faces for accurate inside diameter (I) measurement. Metric Code No. Range* ccuracy Graduation Remarks (10) mm ±0.04 mm (20) mm (20) mm ±0.05 mm 0.02 mm (20) mm ±0.07 mm Code No. Range* ccuracy Graduation Remarks Radiused jaws for accurate I measurement (10) mm / 0 (.3) - 12" ±0.04 mm / ±.0015" 0 (20) mm / 0 (.5) - 18" ±0.05 mm / 0 (20) mm / ±.002" 0 (.5) - 24" (20) mm / 0 (1) - 40" (20) mm / 0 (1) - 60" (20) mm / 0 (1) - 80" *( ): Minimum measurable inside dimension. ±0.07 mm / ±.003" ±0.1 mm / ±.004" ±0.12 mm / ±.005" 0.02 mm /.001" +.3" / 7.62 mm to reading in inside measurement +.5" / 12.7 mm to reading in inside measurement +1" / 25.4 mm to reading in inside measurement E H B G J F IMENSIONS K I Range B E F G H I J K mm R mm mm mm R mm mm

25 SERIES 534 Vernier Long Jaw Thumbwheel Caliper Long jaws for measuring hard-to-reach workpiece features. Inside and outside measurements can be read directly from the upper and lower vernier scales. The jaws have radiused measuring faces for accurate inside diameter (I) measurement. Radiused jaws for accurate I measurement Code No. Range* ccuracy Graduation Remarks (10) mm / 0 (.3) - 12" (20) mm / 0 (.8) - 20" (20) mm / 0 (.8) - 30" (20) mm / 0 (1) - 40" *( ): Minimum measurable inside dimension. ±0.04 mm / ±.0015" ±0.06 mm / ±.0025" ±0.08 mm / ±.003" ±0.1 mm / ±.004" 0.02 mm /.001" +10 mm /.394" to reading in inside measurement +20 mm /.787" to reading in inside measurement IMENSIONS E B F G K I J H Range B E F G H I J K mm R mm mm R mm

26 Calipers SERIES 573 BSOLUTE igimatic Coolant Proof Offset Jaw Caliper SERIES 536 Vernier Offset Jaw Caliper The beam-mounted jaw can be adjusted to facilitate measurement of stepped sections and hard-to-getat workpiece features. igimatic models feature Mitutoyo's BSOLUTE system with IP67 ingress protection. No need to reset the origin after switching on. igimatic models enable integration into statistical process control and measurement systems. Technical ata for 573 series ust/water protection level: IP67* 2 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use (1 year: 300 mm model) Code No. Range Resolution ccuracy* 1 BSOLUTE igimatic type mm (0-6") mm (0-8") 0.01 mm (.0005") ±0.02 mm (±.001") mm (0-12") ±0.03 mm (±.0015") Metric Code No. Range Graduation ccuracy Vernier type mm mm 0.05 mm ±0.05 mm mm ±0.08 mm * 1 Excluding quantizing error. pplication example IMENSIONS C C Vernier type BSOLUTE igimatic type B B Range B C mm mm mm C -27

27 t t Technical ata for 573 series ust/water protection level: IP67* 2 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use (1 year: 300 mm model) * 2 Rustproofing treatment to be applied after use. SERIES 573 BSOLUTE igimatic Coolant Proof Offset Centreline Caliper SERIES 536 Vernier Offset Centreline Caliper Specially designed for hole Centre-to-Centre measurements on the same, or offset, planes. igimatic models feature Mitutoyo's BSOLUTE system with IP67 ingress protection. No need to reset the origin after switching on. irect reading of pitch measurements is available due to the offset-value setting function. igimatic models enable integration into statistical process control and measurement systems. Optional ccessories for 573 series : ata hold unit Example 1 Example 2 Code No. Range Resolution ccuracy* 1 BSOLUTE igimatic type mm (.4-6.4") mm (.4-8.4") 0.01 mm (.0005") ±0.03 mm (±.0015") mm ( ") ±0.04 mm (±.0015") Metric pplication example Code No. Range Graduation ccuracy Vernier type mm mm 0.05 mm ±0.05 mm mm ±0.08 mm * 1 Excluding quantizing error. IMENSIONS 30 ø1 10 ø1 10 Vernier type ø1 10 BSOLUTE igimatic type ø1 Range t mm mm mm Range t mm mm mm

28 Calipers SERIES 573 BSOLUTE igimatic Back Jaw Centreline Caliper Specially designed to measure hole Centre-to-Centre and Edge-to-Centre distances. Provided with jaws on the back of the slider, measurements can be read easily from above. irect reading of pitch measurements is possible due to the offset-value setting function. ata output function allows integration into statistical process control and measurement systems. edicated calibration inspection tools are available. Technical ata Scale type: BSOLUTE electrostatic linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3.5 years under normal use Optional ccessories : ata hold unit pplication example (250) 0 50 ± ± ± ø5 Metric Code No. Range Resolution ccuracy* 1 Edge-to-Centre type mm ±0.1 mm 0.01 mm mm ±0.15 mm Centre-to-Centre type mm ±0.1 mm 0.01 mm mm ±0.15 mm * 1 Excluding quantizing error. (10) (25) (30) (40) IMENSIONS ø1 ø20 ø1 ø10-29

29 Technical ata for 573 series ust/water protection level: IP67* 2 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use SERIES 573 BSOLUTE igimatic Coolant Proof Point Caliper SERIES 536 Vernier Point Caliper Narrow-tip jaws fit into very small grooves and tracks, making many previously difficult outside measurements far easier to obtain. Can measure outside and inside dimensions, depth, and steps. igimatic models feature Mitutoyo's BSOLUTE system with IP67 ingress protection. No need to reset the origin after switching on. igimatic models enable integration into statistical process control and measurement systems Code No. Range Resolution ccuracy* 1 BSOLUTE igimatic type mm (0-6") 0.01 mm (.0005") ±0.02 mm (±.001") Metric Code No. Range Graduation ccuracy Vernier Type mm 0.05 mm ±0.05 mm * 1 Excluding quantizing error. IMENSIONS

30 Calipers SERIES 573 BSOLUTE igimatic Coolant Proof Blade Caliper SERIES 536 Vernier Blade Caliper The thin blade-type jaws fit into very small grooves and make previously difficult outside measurements far easier to obtain. The outside measuring faces are carbide tipped. Can measure outside and inside dimensions, depth, and steps. igimatic models feature Mitutoyo's BSOLUTE system with IP67 ingress protection. No need to reset the origin after switching on. igimatic models enable integration into statistical process control and measurement systems. Technical ata for 573 series ust/water protection level: IP67* 2 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use * 2 Rustproofing treatment to be applied after use. Optional ccessories for 573 series 05CZ624: SPC data cable with pushbutton (1 m) 05CZ625: SPC data cable with pushbutton (2 m) Code No. Range Resolution ccuracy* 1 BSOLUTE igimatic type mm (0-6") 0.01 mm (.0005") ±0.02 mm (±.001") Metric Code No. Range Graduation ccuracy Vernier type mm mm 0.05 mm ±0.05 mm mm ±0.08 mm * 1 Excluding quantizing error. pplication example IMENSIONS BSOLUTE igimatic type Vernier type t C B Range B C t mm mm mm

31 Technical ata for 573 series ust/water protection level: IP67* 2 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use * 2 Rustproofing treatment to be applied after use. SERIES 573 BSOLUTE igimatic Coolant Proof Knife Edge Inside Caliper SERIES 536 Vernier Knife Edge Inside Caliper Specially designed for inside measurements in hard-to-reach places. igimatic models feature Mitutoyo's BSOLUTE system with IP67 ingress protection. No need to reset the origin after switching on. igimatic models enable integration into statistical process control and measurement systems. Optional ccessories for 573 series Code No. Range Resolution ccuracy* 1 Min. measurable hole BSOLUTE igimatic type mm (.4-8") 0.01 mm (.0005") ±0.05 mm (±.002") ø10 mm (ø.4") Metric Code No. Range Graduation ccuracy Min. measurable hole Vernier type mm 0.05 mm ±0.12 mm ø10 mm * 1 Excluding quantizing error X X pplication example IMENSIONS X X Section X - X Section X - X -32

32 Calipers SERIES 573 BSOLUTE igimatic Coolant Proof Inside Groove Caliper SERIES 536 Vernier Inside Groove Caliper Specially designed for inside measurements in hard-to-reach places. igimatic models feature Mitutoyo's BSOLUTE system with IP67 ingress protection. No need to reset the origin after switching on. igimatic models enable integration into statistical process control and measurement systems. Technical ata for 573 series ust/water protection level: IP67* 3 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use * 3 Rustproofing treatment to be applied after use. Optional ccessories for 573 series Code No. Range Resolution ccuracy* 1 Min. measurable hole BSOLUTE igimatic type * mm (.4-6") 0.01 mm (.0005") ±0.05 mm (±.002") ø10 mm (ø.4") Metric Code No. Range Graduation ccuracy Min. measurable hole Vernier type mm 0.05 mm ±0.05 mm ø10 mm * 1 Excluding quantizing error. * 2 Equipped with the offsetting function, which indicates the actual measurement value. pplication example IMENSIONS R5 R5 R5 R5-33

33 c Technical ata for 573 series ust/water protection level: IP67* 3 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use * 3 Rustproofing treatment to be applied after use. SERIES 573 BSOLUTE igimatic Coolant Proof Point Jaw Inside Caliper SERIES 536 Vernier Point Jaw Inside Caliper Specially designed for inside measurements in hard-to-reach places. igimatic models feature Mitutoyo's BSOLUTE system with IP67 ingress protection. No need to reset the origin after switching on. igimatic models enable integration into statistical process control and measurement systems. Optional ccessories for 573 series Code No. Range Resolution ccuracy* 1 Min. measurable hole BSOLUTE igimatic type * mm (.8-6") 0.01 mm (.0005") ±0.03 mm (±.0015") ø20 mm (ø.8") Metric More than ø20 pplication example Code No. Range Graduation ccuracy Min. measurable hole Vernier type mm ±0.05 mm ø20 mm mm ±0.08 mm ø30 mm 0.05 mm mm ±0.10 mm ø70 mm mm ±0.12 mm * 1 Excluding quantizing error. * 2 Equipped with the offsetting function, which indicates the actual measurement value. IMENSIONS Vernier type a BSOLUTE igimatic type (233) b (16) g f e d 60 ø2.4 (ø5)* ø0.5 (ø1)* (e) (60 ) ø0.5 ø2.4 *450 and 600 mm range models 10 Range a b c d e f g mm mm mm mm

34 Calipers SERIES 573 BSOLUTE igimatic Coolant Proof Neck Jaw Caliper SERIES 536 Vernier Neck Jaw Caliper Can measure wall thickness inside bores and recesses. igimatic models feature Mitutoyo's BSOLUTE system with IP67 ingress protection. No need to reset the origin after switching on. igimatic models enable integration into statistical process control and measurement systems. Technical ata for 573 series ust/water protection level: IP67* 2 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use * 2 Rustproofing treatment to be applied after use. Optional ccessories for 573 series Code No. Range Resolution ccuracy* 1 Remarks BSOLUTE igimatic type mm (0-6") 0.01 mm (.0005") ±0.03 mm (±.0015") Point type pplication examples Metric Code No. Range Graduation ccuracy Vernier type mm 0.05 mm ±0.05 mm Point type * 1 Excluding quantizing error. IMENSIONS ø2.4 ø

35 Technical ata for 573 series ust/water protection level: IP67* 2 Scale type: BSOLUTE electromagnetic induction linear encoder Battery: SR44 (1 pc.), Battery life: pprox. 3 years under normal use * 2 Rustproofing treatment to be applied after use. SERIES 573 BSOLUTE igimatic Coolant Proof Tube Thickness Caliper SERIES 536 Vernier Tube Thickness Caliper The beam-mounted jaw is a round bar that facilitates measurements of tube wall thickness. igimatic models feature Mitutoyo's BSOLUTE system with IP67 ingress protection. No need to reset the origin after switching on. igimatic models enable integration into statistical process control and measurement systems. Optional ccessories for 573 series Code No. Range Resolution ccuracy* 1 BSOLUTE igimatic type mm (0-6") 0.01 mm (.0005") ±0.05 mm (±.002") Metric More than ø3 Code No. Range Graduation ccuracy Vernier type mm 0.05 mm ±0.05 mm * 1 Excluding quantizing error. pplication examples IMENSIONS ø3 229 (32) ø3-36

36 Calipers SERIES 536 Vernier Hook Jaw Caliper Can measure width of grooves and lands inside bores and recesses pplication examples Metric Code No. Range Graduation ccuracy Remarks (10) mm 0.02 mm ±0.03 mm (20) mm With fine adjustment * ( ): Minimum dimension in inside measurement. IMENSIONS L d a b More than ø Inside-groove type More than ø3 f R5: Flat: e g c Code No. L a b c d e f g

37 SERIES 536 Vernier Moving Jaw Caliper The moving jaw can be rotated to measure sectioned shafts. Can measure outside and inside dimensions, depth, and steps Metric Code No. Range Graduation ccuracy mm 0.05 mm ±0.05 mm IMENSIONS

38 Calipers SERIES 573 BSOLUTE igimatic Low Force Caliper ue to the low measuring force, this caliper is ideal for measuring elastic workpieces such as plastic parts and rubber parts that standard calipers cannot measure accurately. The thumb roller allows smooth and easy fine adjustment. Movement of main scale jaw is 0.3 mm. Measuring force: 0.49 to 0.98 N (50 to 100 gf) Features Mitutoyo's BSOLUTE system. No need to reset the origin after switching on. Slider operation is smooth and comfortable. ata output function allows integration into statistical process control and measurement systems. Technical ata Scale type: BSOLUTE electrostatic linear encoder Jaw retraction: 0.3 mm Battery: SR44 (1 pc.), Battery life: pprox. 3.5 years under normal use Code No. Range Resolution ccuracy* mm (0-7") 0.01 mm (.0005") ±0.05 mm (±.002") * Excluding quantizing error. IMENSIONS (15.8) 40 (299) 3.5 Measurement procedure consistently low measuring force can be guaranteed by only taking measurements when the pointer is between the two fiducial lines. ORIGIN IGIMTIC ON/OFF ZERO/BS (69) (23.6) 6-39

39 SERIES 573 BSOLUTE igimatic Snap Caliper Technical ata Repeatability: 0.01 mm Scale type: BSOLUTE electrostatic linear encoder Jaw retraction: 2 mm Battery: SR44 (1 pc.), Battery life: pprox. 3.5 years under normal use Features a 'snap action' movement control of the slider via a spring-loaded mechanism attached to a movable clamp on the beam. Enables quick and efficient repetitive GO/NO-GO inspection of a specific dimension on mass produced parts by just moving a lever. Can measure outside and inside dimensions, depth, and steps. Measuring force: 7 to 14 N (700 to 1400 gf) The slider can be retracted by up to 2 mm from the measuring position. Features Mitutoyo's BSOLUTE system. No need to reset the origin after switching on. Slider operation is smooth and comfortable. ata output function allows integration into statistical process control and measurement systems Code No. Range Resolution ccuracy* mm (0-4") mm (0-6") 0.01 mm (.0005") ±0.02 mm (±.001") * Excluding quantizing error. IMENSIONS E C B 27.5 Range B C E mm mm

40 ME IN JPN ME IN JPN Quick Guide to Precision Measuring Instruments Calipers Nomenclature Vernier Caliper (M-type) Inside measuring faces Step measuring faces Screw, gib setting Gib, slider Locking screw Screw, gib pressing Beam Stop, slider epth bar Inside jaws Outside jaws Thumbwheel Main scale Reference surface epth measuring faces Outside measuring faces bsolute igimatic Caliper (M-type) Inside measuring faces Step measuring faces Slider Vernier scale Slider Locking screw Output connector Beam epth bar Inside jaws Outside jaws Main scale Thumb-roller ZERO Set/bsolute mode button Reference surface epth measuring faces Outside measuring faces How to Read the Scale Vernier Calipers ial Calipers Measurement Examples 1. Outside measurement 2. Inside measurement 0 (1) Main scale (1) mm 30 (2) mm (2) Main scale Vernier scale (2) ial face 3. Step measurement 4. epth measurement Graduation 0.05 mm (1) Main scale reading 4.00 mm (2) Vernier scale reading 0.75 mm Caliper reading 4.75 mm Graduation 0.01 mm (1) Main scale reading 16 mm (2) ial face reading 0.13 mm ial Caliper reading mm Note) bove left, 0.75 mm (2) is read at the position where a main scale graduation line corresponds with a vernier graduation line. Special Purpose Caliper pplications Point jaw type Offset jaw type epth type Blade jaw type Neck type Tube thickness type For uneven surface measurement For stepped feature measurement For depth measurement For diameter of narrow groove measurement For outside diameter measurement such as behind a shrouded recess For tube or pipe thickness measurement -41

41 Types of Vernier Scale The Vernier scale is attached to the caliper s slider and each division on this scale is made 0.05 mm shorter than one main scale division of 1 mm. This means that, as the caliper jaws open, each successive movement of 0.05 mm brings the succeeding vernier scale line into coincidence with a main scale line and so indicates the number of 0.05 mm units to be counted (although for convenience the scale is numbered in fractions of a mm). lternatively, one vernier division may be made 0.05 mm shorter than two divisions of the main scale to make a long vernier scale. This makes the scale easier to read but the principle, and discrimination, is still the same. Standard Vernier scale (graduation 0.05 mm) Long Vernier scale (graduation 0.05 mm) Small Hole Measurement with an M-Type Caliper small error occurs when you measure the internal diameter of a small hole with the inside jaws. This is because there is an offset (H) due to the thickness of the jaws and the clearance between them. ø : True internal diameter ød : Indicated internal diameter d: Measurement error (ø ød) True internal diameter (ø: 5 mm) H d mm H Reading 1.45 mm Reading mm bout Long Calipers Steel rules are commonly used to roughly measure large workpieces but if a little more accuracy is needed then a long caliper is suitable for the job. long caliper is very convenient for its user friendliness but does require some care in use. In the first place it is important to realize there is no relationship between resolution and accuracy. For details, refer to the values in our catalogue. Resolution is constant whereas the accuracy obtainable varies dramatically according to how the caliper is used. The measuring method with this instrument is a concern since distortion of the main beam causes a large amount of the measurement error, so accuracy will vary greatly depending on the method used for supporting the caliper at the time. lso, be careful not to use too much measuring force when using the tips of the measuring faces of a long-jaw caliper. Inside Measurement with a CM-Type Caliper Because the inside measuring faces of a CM-type caliper (see illustration at left) are at the tips of the jaws the measuring face parallelism is heavily affected by measuring force, and this becomes a large factor in the measurement accuracy attainable. In contrast to an M-type caliper, a CM-type caliper cannot measure a very small hole diameter because it is limited to the size of the stepped jaws, although normally this is no inconvenience as it would be unusual to have to measure a very small hole with this type of caliper. Of course, the radius of curvature on the inside measuring faces is always small enough to allow correct hole diameter measurements right down to the lowest limit (jaw closure). Mitutoyo CM-type calipers are provided with an extra scale on the slider for inside measurements so they can be read directly without the need for calculation, just as for an outside measurement. This useful feature eliminates the possibility of error that occurs when having to add the inside-jawthickness correction on a single-scale caliper. ød ø For inside only For outside only -42