Table of Contents. 580 Electronics

Transcription

1 Table of Contents Ancre 580 Electronics Features and Benefits 06 DeviceNet 07 Ethernet/IP TM 09 Profibus-DP PROFINET EtherNet/IP TM DLR 5 IO-Link Class A & B 7 EMERSON CHARM 9 Dimensional Drawing Fieldbus Communication Assembly - ATEX Certification (50/50) How to Order Assembly Kit & 580 Electronics How to Order Complete 580 Manifold Assemblies 5..6 How to Order - Sandwich shut off block 7 0GB-07/R0 Fielbus Electronics - 05

2 FIELDBUS ELECTRONICS 580 Electronics (Series 50-50: M7 to /8 (G or NPT) or with push-in fittings Ø to mm) Series Fieldbus - Electronics Made Easy! Innovative Graphic Display is used for easy commissioning, visual status & diagnostics Commissioning Capabilities Set network address (including IP & Subnet mask for Ethernet) Set baud rate Set factory defaults Visual Diagnostics Shorted and open load detection Shorted sensor/cable detection Low & missing power detection Self-tests activation Log of network errors Graphic Display for configuration & diagnostics 580 Fieldbus Communications Electronics Why use Numatics Fieldbus communication electronics? Modular Reality... No internal wiring simplifies assembly Power connector allows output power to be removed while inputs and communication are left active IP65 protection Compact Electronic Module Supported Protocols DeviceNet Ethernet/IP PROFIBUS -DP PROFINET EtherNET/IP DLR IO-Link (Class A & Class B) CHARMs DeviceNet TM is a trademark of ODVA. PROFIBUS and PROFINET are registered trademarks of Profibus International Fielbus Electronics 0GB-07/R0

3 DeviceNet DeviceNet is an open bus fieldbus communication system developed by Allen-Bradley based on Controller Area Network (CAN) technology. The governing body for DeviceNet is the Open DeviceNet Vendors Association (ODVA). The ODVA controls the DeviceNet specification and oversees product conformance testing. Numatics 580 nodes for DeviceNet have an integrated graphic display. They have been tested and approved for conformance by the ODVA. More information about DeviceNet and the ODVA can be obtained from the following WEB site: Description DeviceNet communications module (node) ATEX - (GD) IP65X - (GD) IP5X (G) IP5X HOW TO ORDER Consult the online configurator - CAD files on: DeviceNet 5 COMMUNICATION MALE Pin = Shield Pin = V+ ( V DC) Pin = V- (Ground) Pin = CAN_H Pin 5 = CAN_L POWER MALE Pin = + V DC (node) Pin = + V DC (Valves) Pin = 0 V DC (node) Pin = 0 V DC (Valves) Technical Data Electrical Data Voltage Current Node Power at Max. Brightness V DC +/- 0% 0,070 A BUS Power -5 V DC Valves V DC +/- 0% 8 A Maximum Power Connector Single key pin M (male) Communication Connector Single key 5 pin M (male) LED's Module Status and Network Status 0GB-07/R0 Operating Data Temperature Range (ambient) -0ºC to +50ºC Humidity 95% relative humidity, non-condensing Vibration / Shock IEC , IEC Moisture Protection IP65 Configuration Data Graphic Display Display used for setting Node Address, Baud Rate, Fault / Idle Actions, and all other system settings. Maximum Valve-Solenoid Outputs 8 (50) / (50) Network Data Supported Baud Rates 5K Baud, 50K Baud, 500K Baud, with Auto-Baud detection Supported Connection Type Polled, Cyclic, Change of State (COS) and combination Message Capability Bus Connector Single key 5 pin M (male) Diagnostics Power, short, open load conditions are monitored Special Features Supports Auto-Device Replacement (ADR) and fail-safe device settings Weight DeviceNet Communication Module 5 g Fielbus Electronics - 07

4 DeviceNet bus connection the front panel of the communication module for DeviceNet is equipped with a 5 pin 7/8-6 UN male socket (E). The bus can be connected in the two following ways: directly to the module with a T-connector; with a straight connector, cable (max. length: m) and a DeviceNet distributor box. The modules on either side of the system must be provided with terminating resistors (L or L). Wiring with T-connector Connection with DeviceNet distributor box (X) K G F H K K K m max. L E K J G E BUS V DC power supply Accessories for DeviceNet The modules on either side of the system must be provided with terminating resistors H Accessory Description Order Code G M 90 5 Pin Female Field Wireable network Connector Spring Cage (A coded) PG9 cable gland M Straight 5 Pin Female Field Wireable network Connector Spring Cage PG9 cable gland TD05F V TC05F V H M Straight 5 Pin Male Field Wireable network Connector Spring Cage PG9 cable gland TA05F V F Way M T (T-connector M, 5 male / female / female pins) TC TT05000 L J (K) Cable to be ordered separately. Terminating resistor male plug TA05TR Terminating resistor female plug M 90 Pin Female Field Wireable Connector (PG 9 Cable Gland) ( pin elbow female cable connector 7/8 ) - V DC power supply M 90 Pin Female Single Ended Cable, Euro Color Code ( pin elbow female cable connector 90 with 0 m cable) V DC power supply BN (brown) WH (white) BU (blue) BK (black) TD0F TD00MAE GB-07/R Fielbus Electronics

5 Ethernet/IP TM Ethernet TM used throughout the world to network millions of PC s has now evolved into a viable industrial network. Ethernet TM is an open architecture high-level communication network that meets the demands of today s industrial applications requiring highspeed (0/00 Mbit/s), high-throughput and flexibility. Additionally, Ethernet TM technology can integrate an on-board Web server, which can make the node readily accessible for configuration, testing and even retrieval of technical documentation. Numatics 580 nodes for Ethernet TM have an integrated graphic display. The 580 Ethernet/IP TM nodes have been tested and approved for conformance by the ODVA. More information about Ethernet/IP TM and the ODVA can be obtained from the following WEB site: www. odva.org Description Ethernet/IP TM communications module (node) ATEX - (GD) IP65X - (GD) IP5X (G) IP5X HOW TO ORDER Consult the online configurator - CAD files on: Ethernet/IP Technical Data COMMUNICATION FEMALE Pin = TX+ Pin = RX+ Pin = TX- Pin = RX- POWER MALE Pin = + V DC (node) Pin = + V DC (Valves) Pin = 0 V DC (node) Pin = 0 V DC (Valves) Electrical Data Voltage Current Node Power at Max. Brightness VDC +/- 0% 0,09 A Valves VDC +/- 0% 8 A maximum Power Connector Single key pin M (male) Communication Connector D-coded 5 pin M (female) LED's Module Status, Network Status and Activity/Link 0GB-07/R0 Operating Data Temperature Range (ambient) -0ºC to +50ºC Humidity 95% relative humidity, non-condensing Vibration / Shock IEC , IEC Moisture Protection IP65 Configuration Data Graphic Display Display used for setting Subnet mask, Fault / Idle Actions, DHCP / BootP and all other system settings. Maximum Valve-Solenoid Outputs 8 (50) / (50) Network Data Supported Baud Rates 0 Mbit / 00 Mbit Bus Connector D-coded 5 pin M (female) Diagnostics Power, short, open load conditions and module health are monitored Special Features Integrated web server, fail-safe device settings, HTTP, FTP, and UNICAST (for EtherNet/IP) Weight Ethernet Communication Module 6 g Fielbus Electronics - 09

6 Accessories for EtherNet/IP Accessory Description Order Code M Straight Pin Male D-Coded to Male RJ5 network Cable - Shielded 5 m QA005MK0VA m QA00MK0VA0000 M elbow Pin Male D-Coded Field Wireable network Connector PG 9 Cable Gland Screw Terminal QB0F N M 90 Pin Female Field Wireable Connector (PG 9 Cable Gland) ( pin elbow female cable connector 7/8 ) - V DC power supply TD0F M 90 Pin Female Single Ended Cable, Euro Color Code ( pin elbow female cable connector 90 with 0 m cable) V DC power supply BN (brown) WH (white) BU (blue) BK (black) TD00MAE GB-07/R0 0 - Fielbus Electronics

7 PROFIBUS-DP PROFIBUS-DP is a vendor-independent, open fieldbus protocol designed for communication between automation control systems and distributed I/O at the device level. Numatics 580 nodes for PROFIBUS-DP have an integrated graphic display. The 580 nodes for PROFIBUS-DP have been designed and tested to conform to the PROFIBUS standard EN5070. Certification has been done by the PROFIBUS Interface Center (PIC) according to the guidelines determined by the PROFIBUS Trade Organization (PTO). The Description certification process ensures interoperability for all PROFIBUS devices. More information regarding PROFIBUS can be obtained from the following WEB site: PROFIBUS-DP communications module DPV0/DPV ATEX - (GD) IP65X - (GD) IP5X (G) IP5X HOW TO ORDER Consult the online configurator - CAD files on: 5 PROFIBUS-DP 5 Technical Data COMMUNICATION FEMALE OUT Pin = +5V DC Pin = RxD/TxD-N / Data Line A Pin = DATA GROUND (0V DC) Pin = RxD/TxD-P / Data Line B Pin 5 = No Connected Thread = Shield COMMUNICATION MALE IN Pin = No Connected Pin = RxD/TxD-N / Data Line A Pin = No Connected Pin = RxD/TxD-P / Data Line B Pin 5 = No Connected Thread = Shield 5 POWER MALE Pin = + V DC (node) Pin = 0 V DC (Valves) Pin = 0 V DC (node) Pin = + V DC (Valves) Pin 5 = Earth Ground Electrical Data Voltage Current Node Power at Max. Brightness VDC +/- 0% 0,09 A Valves VDC +/- 0% A Maximum Power Connector Single key 5 pin M (male) Communication Connector Single reverse key (B-Coded) 5 pin M ( male and female) LED's Module Status and Network Status 0GB-07/R0 Operating Data Temperature Range (ambient) -0ºC to +50ºC Humidity 95% relative humidity, non-condensing Vibration / Shock IEC , IEC Moisture Protection IP65 Configuration Data Graphic Display Display used for setting Node Address, Baud Rate, Fault / Idle Actions, Diagnostics and all other system settings. Maximum Valve-Solenoid Outputs 8 (50) / (50) Network Data Supported Baud Rates Auto-Baud Bus Connector Single reverse key (B-coded) 5 pin M ( male and female) Diagnostics Power, short, open load conditions and module health are monitored Special Features Supports Auto-Device Replacement (ADR) and fail-safe device settings Weight PROFIBUS-DP Communication Module g Fielbus Electronics -

8 PROFIBUS-DP bus connection The front panel of the communication module for Profibus-DP is equipped with: - a 5 pin male 7/8 socket for power supply - a 5 pin male M-B socket or 5 pin female M-A socket for the bus cable (with a T-connector on integrated M COM-IN/ COM-OUT connector) Fieldbus connection Wiring with T-connector K FIELDBUS ELECTRONICS - SERIES 580 L H F J G K BUS V DC power supply Accessories for PROFIBUS-DP The modules on either side of the system must be provided with terminating resistors H Accessory Description Order Code F T-connector M-B, 5 female / male / male pins (Profibus Mb max) G M-B network connector, 5 female pins - for cable dia. 6-8 mm (Profibus Mb max) M 90 5 Pin Male & Female Field Wireable network Connectors, w/idc PG9 Cable Gland IDC FEMALE RD05F00P00007V M-B network connector, 5 male pins - for cable dia. 6-8 mm (Profibus Mb max) L M 90 5 Pin Male & Female Field Wireable network Connectors, w/idc PG9 Cable Gland IDC MALE RB05F00P00007V H Terminating resistor M-B - male plug J (K) Cable to be ordered separately. - Fielbus Electronics M 90 5 Pin Female Field Wireable Connector ( V DC supply, PG 9 Cable Gland) M 90 5 Pin Female Single Ended Cable, Euro Color Code (5 pin elbow female cable connector, V DC supply, with 0 m cable) 5 5 BN (brown) WH (white) BK (black) BU (blue) GN/YE (green/yellow) TD05F TD050MAE Dust cover - M female GB-07/R0

9 PROFINET PROFINET is the innovative open standard for Industrial Ethernet, development by Siemens and the Profibus User Organization (PNO). PROFINET complies to IEC 658 and IEC 678 standards. PROFINET products are certified by the PNO user organization, guaranteeing worldwide compatibility. Numatics 580 nodes for PROFINET IO (PROFINET RT) have an integrated graphic display. PROFINET is based on Ethernet and uses TCP/IP and IT standards and complements them with specific protocols and mechanisms to achieve Real Time performance. Additionally, the 580 node PROFINET can integrate an on-board Web server, which can make the node readily accessible for configuration, testing and even retrieval of technical documentation. More information regarding PROFINET can be obtained from the following WEB site: Remark: Compatibility with MRP functionnalities. Description PROFINET communications module (node) FIELDBUS ELECTRONICS - SERIES 580 ATEX COMMUNICATION FEMALE Pin = TD+ Pin = RD+ Pin = TD- Pin = RD- - (GD) IP65X - (GD) IP5X (G) IP5X HOW TO ORDER Consult the online configurator - CAD files on: PROFINET POWER MALE Pin = + V DC (node) Pin = 0 V DC (Valves) Pin = 0 V DC (node) Pin = + V DC (Valves) Pin 5 = Earth Ground 5 Technical Data COMMUNICATION FEMALE Pin = TD+ Pin = RD+ Pin = TD- Pin = RD- Electrical Data Voltage Current Node Power at Max. Brightness VDC +/- 0% Valves VDC +/- 0% A Maximum Power Connector Single key 5 pin M (male) Communication Connector Two D-coded pin M (female) LED's Module Status, Network Status and Activity/Link 0GB-07/R0 Operating Data Temperature Range (ambient) -0ºC to +50ºC Humidity 95% relative humidity, non-condensing Vibration / Shock IEC , IEC Moisture Protection IP65 Configuration Data Graphic Display Display used for setting IP Address, Subnet Mask, Fault / Idle Actions, Diagnostics and all other system settings. Maximum Valve-Solenoid Outputs 8 (50) / (50) Network Data Supported Baud Rates 0 Mbit / 00 Mbit Bus Connector Two D-coded pin M (-Female) Diagnostics Power, short, open load conditions and module health and configuration are monitored Special Features Integrated web server, Integrated port switch, fail-safe device settings Weight PROFINET Communication Module g Fielbus Electronics -

10 Accessories for PROFINET Accessory Description Order Code 5 m QA005MK0VA0000 M Straight Pin Male D-Coded to Male RJ5 network Cable - Shielded 0 m QA00MK0VA0000 M elbow Pin Male D-Coded Field Wireable network Connector PG 9 Cable Gland Screw Terminal QB0F N M 90 5 Pin Female Field Wireable Connector ( V DC supply, PG 9 Cable Gland) TD05F M 90 5 Pin Female Single Ended Cable, Euro Color Code (5 pin elbow female cable connector, V DC supply, with 0 m cable) BN (brown) WH (white) BK (black) TD050MAE BU (blue) 5 GN/YE (green/yellow) - Fielbus Electronics 0GB-07/R0

11 EtherNet/IP TM DLR EtherNet/IP TM used throughout the world to network millions of PC s has now evolved into a viable industry network. EtherNet/ IP is an open architecture high-level communication network that meets the demands of today s industrial applications requiring high-speed (0/00 Mbit/s), high-throughput and flexibility. Additionally, EtherNet/IP TM technology can integrate an on-board Web server, which can make the node readily accessible to any standard Web browser for configuration, testing and even retrieval of technical documentation. Numatics 580 EtherNet/IP TM DLR (Device Level Ring) node with integrated display, has an embedded switch which allows the unit to be used in simplified networks with linear topology configurations (daisy chain). Additionally, the DLR compatibility allows the node to be used in a fault tolerant ring network, when using appropriate EtherNet/IP TM DLR scanners. DLR configuration allows communication Description recovery from a single point failure on the network ring (e.g. failed network connection or cable). The 580 EtherNet/IP TM nodes have been tested and approved for conformance by the ODVA More information about EtherNet TM and the ODVA can be obtained from the following WEB site: Open Device Vendors Association (ODVA) EtherNet/IP TM DLR communications module (node) ATEX - (GD) IP65X - (GD) IP5X (G) IP5X HOW TO ORDER Consult the online configurator - CAD files on: Ethernet/IP DLR COMMUNICATION FEMALE Pin = TX+ Pin = RX+ Pin = TX- Pin = RX- POWER MALE Pin = + V DC (node) Pin = + V DC (Valves) Pin = 0 V DC (node) Pin = 0 V DC (Valves) Technical Data Electrical Data Voltage Current Node Power at Max. Brightness Valves Power Connector Communication Connector LED's VDC +/- 0% A Maximum Single key pin M (male) Two D-coded pin M (female) Module Status, Network Status and Activity / Link 0GB-07/R0 Operating Data Temperature Range Humidity -0ºC to +50ºC 95% relative humidity, non-condensing Vibration / Shock IEC , IEC Moisture Configuration Data Graphic Display IP65 Certified Maximum Valve Solenoid Outputs 8 (50) / (50) Network Data Supported Baud Rates Bus Connector Diagnostics Special Features Weight EtherCAT communications module Display used for setting IP address, Subnet Mask, Fault / Idle Actions, Diagnostics and all other system settings. 0 Mbit / 00 Mbit Two D-coded pin M (female) Power, short, open load conditions and module health and configuration are monitored Embedded two port switch, Device Level Ring (DLR) compatibility, fail-safe device settings, integrated web server, HTTP, TFTP, UNICAST g Fielbus Electronics - 5

12 Accessories for EtherNET/IP TM DLR Accessory Description Order Code M Straight Pin Male D-Coded to Male RJ5 network Cable - Shielded 5 m QA005MK0VA m QA00MK0VA0000 M elbow Pin Male D-Coded Field Wireable network Connector PG 9 Cable Gland Screw Terminal QB0F N M 90 Pin Female Field Wireable Connector (PG 9 Cable Gland) ( pin elbow female cable connector 7/8 ) - V DC power supply TD0F M 90 Pin Female Single Ended Cable, Euro Color Code ( pin elbow female cable connector 90 with 0 m cable) V DC power supply BN (brown) WH (white) BU (blue) BK (black) TD00MAE GB-07/R0 6 - Fielbus Electronics

13 IO-Link (Class A & Class B) IO-Link is a globally standardized IO technology (IEC 6-9) developed primarily for communication with smart sensors and actuators that can also be used with valves and other field devices. IO-Link is used to individually link field devices and resides below the I/O level. An IO-Link Master with a higher level fieldbus or Ethernet communication protocol is required. The IO-Link Consortium, which is a technical committee within PROFIBUS & PROFINET International (PI), oversees and manages IO-Link specifications. Numatics IO-Link communications node offers both event based as well as standard I/O mapped diagnostics, requires minimal commissioning, and is compatible with distributed modular I/O. Supports both Class A ( pin) and Class B (5 pin) with isolated ground) communication port types. More information regarding IO-Link can be obtained from the following website: Description IO-Link Class A ( pin) Communications Module (node) IO-Link Class B (5 pin) Communications Module (node) ATEX - (GD) IP65X - (GD) IP5X (G) IP5X - (GD) IP65X - (GD) IP5X (G) IP5X HOW TO ORDER Consult the online configurator - CAD files on: Technical Data IO-Link (Class A & Class B) The IO-Link (Port Type A) The IO-Link (Port Type B) connector is a single keyway pin connector is a single keyway 5 pin M male connector 5 M male connector Pin = + V DC PWR Pin = + V DC PWR Pin = + V DC (Valves) Pin = + V DC (Valves) Pin = 0 V DC PWR (Valves) Pin = 0 V DC PWR Pin = IO-Link COMM (C/Q) Pin = IO-Link COMM (C/Q) Pin 5 = NO CONNECT Pin 5 = 0 V DC (Valves) 5 Node Power VDC +/- 0% 0,00 A Valves VDC +/- 0% A Maximum Power and Communication Connector Class A: A-Coded pin M (male)/class B: A-Coded 5 pin M with isolated ground (male) LEDs Valve Power, Node Power, Communication Temperature Range (ambient) -0ºC to 50ºC Humidity 95% Relative Humidity, Non-condensing Vibration/Shock IEC , IEC Moisture IP65 Certified 09GB-07/R0 Maximum Valve Solenoid Outputs 8 (50) / (50) Supported Baud Rates COM : 8,K Diagnostics Special Features IO-Link Communications Module IO Link field wireable Power, short, open load conditions with both standard I/O mapped diagnostics and event based diagnostics Fail-safe device settings Class A: 98 g, Class B: 0 g M straight 5 pins Female A-Coded IO Link field wireable PG-9 Cable Gland TC05F M 90 Elbow 5 pins Female A-Coded IO Link field wireable PG-9 Cable Gland TD05F Fielbus Electronics - 7

14 Accessories for IO-Link (Class A & Class B) Accessory Description Order Code M Class A Compatible Cables M Straight Pin Male Single Ended Cable, Euro Color Code,5 m TA0E5MIE00007P 5 m TA005MIE00007P M 90 Pin Male Single Ended Cable, Euro Color Code,5 m TB0E5MIE00007P 5 m TB005MIE00007P M Straight Pin Male to Female Cable Extension,5 m TC0E5MIETA07P m TC00MIETA07P M Class B Compatible Cables 5 m TC0505MIE00007P M Straight 5 Pin Female Single Ended Cable - Unshielded 0 m TC050MIE00007P 5 m TC0505MIETA057P M Straight 5 Pin Female to Male Double Ended Cable - Unshielded 0 m TC050MIETA057P 5 m TD0505MIE00007P M 90 5 Pin Female Single Ended Cable - Unshielded 0 m TD050MIE00007P Molded Body/Insert TPU Polyamide Coupling Nut Nickel Plated Zinc Nickel Plated Zinc Cable Jacket Material PUR NA Cable O.D. 5mm Accepts 6,5 mm Voltage Rating 60 V 5 V Current Rating A A Degree of Protection IP65 (mated) IP65 (mated) Operating Temperature -5 C to 90 C -0 C to 00 C Conductor Gauge AWG 8 AWG Minimum Bend Radius 50 mm NA Wire Connection NA Screw Terminal 8 - Fielbus Electronics Female View 09GB-07/R0

15 580 CHARM Node The 580 CHARM node allows the pneumatic valve manifold to directly connect to the CHARM I/O Card (CIOC) baseplate and be controlled by DeltaV. The 580 CHARM node is connected via cables to the bottom baseplate extender of the (CIOC). This provides full redundancy to the pneumatic manifold. The 580 CHARM node is commissioned via the DeltaV explorer. Description 580 CHARM module (node) ATEX - (GD) IP65X - (GD) IP5X HOW TO ORDER Consult the online configurator - CAD files on: (G) IP5X CHARM 5 Technical Data Electrical Data Voltage Current Comm. Power (via baseplate extender) 6, V 00 ma Valve Power (via baseplate extender) V,07 A Power and Communication Connector LED's A-coded 5 Pin M (male) Module Status and Network Status COMMUNICATION MALE Pin = Shield Pin = V+ ( V DC) Pin = V- (Ground) Pin = CAN_H Pin 5 = CAN_L 09GB-07/R0 Operating Data Temperature Range (ambient) Humidity Vibration / Shock Moisture Protection Configuration Data Graphic Display -0ºC to +50ºC 95% relative humidity, non-condensing IEC , IEC IP65 Maximum Valve-Solenoid Outputs 8 (50 Series) / (série 50) Network Data Redundant Power and Comm. Connectors (Primary & Secondary) Diagnostics DeltaV version Weight CHARM Communication Node Display used for setting CHARM address and all other system settings. A-coded 5 Pin M (male) Power, short, open load conditions are monitored Compatible DeltaV series S ; FHX file integrated in v version ; download file for v and v versions 6 g Fielbus Electronics - 9

16 CHARM Communication & Power connection the front panel of the communication module is equipped with a 5 pin M. Address Plug CHARM Baseplate Address Plug CHARM Baseplate Primary Comm. & Power Secondary Comm. & Power Address Plug Address Plug CHARM Baseplate CHARM Baseplate Both Cables provide 6. V for Comm. and V for valve Power Accessories for CHARM Accessory Description Order Code - Cables with M and sub-d plug (,5 m) P599AF ,5 Meter Cable with M and Sub-D Connectors (Moulded version) P599AF ,5 Meter Cable with M and Sub-D Connectors (Moulded version) P599AF Valve Power Isolator M-Y P599AF Fielbus Electronics 09GB-07/R0

17 Dimensions (mm) Dimensional Drawing Fieldbus Manifold Assembly 50 Series Valve Manifold Assembly with 580 Electronics Configurator - CAD Files,5 97 (8,5 x ) [ 6 subbases],8 9, 97, , 7, 76,6 M7 x /8 Ø5,5 mm Ø5,5 mm WARNING : DO NOT CONNECT OR DISCONNECT PLUGS AND SOCKETS WHEN ENERGIZED WARNING : POTENTIAL ELECTROSTATIC CHARGING HAZARD - SEE INSTRUCTIONS 8, 0GB-07/R0 * - For valve manifold dimensions refer to Valve Series product catalogs Fielbus Electronics -

18 Dimensions (mm/ Inches) Dimensional Drawing Fieldbus Manifold Assembly 50 Series Valve Manifold Assembly with 580 Electronics P [ 6 subbases] Q R /8 x /8 N K J M L H x Ø5,5 mm A C - Fielbus Electronics WARNING : POTENTIAL ELECTROSTATIC CHARGING HAZARD - SEE INSTRUCTIONS A C E F G H J K L M N P Q R ,95, 75,8 6 07, 9,5 87,8 9, 68,, * - For valve manifold dimensions refer to Valve Series product catalogs E WARNING : DO NOT CONNECT OR DISCONNECT PLUGS AND SOCKETS WHEN ENERGIZED F G 0GB-07/R0

19 ATEX CERTIFICATION ATEX Directive Apparatus suitable for use in ATEX Group II, Category, gas (G) or dust (D) environments Temperature class: T (gas), T85 C (dusts) Ingress protection: IP65 / IP5 Ambient temperature range: -0 C Ta +50 C (50/50) Marking: Gas and dusts: II G Ex na IIC T Gc IP5 X or IP65 X II D Ex tc IIIA or IIIB T85 C Dc IP5 X or Ex tc IIIC T85 C Dc IP65 X Dusts: II G Ex na IIC T Gc IP5 X SPECIAL CONDITIONS FOR SAFE USE The apparatus must be installed in a control cabinet with a protection degree of IP5 or IP65 in conformance with standards EN and EN (and EN for dust applications). WARNING LIVE PARTS: DO NOT DISCONNECT CONNECTORS FROM SOCKETS WHILE POWER IS ON The cross-section of the ground cable must be equal to the minimum cross-section of the supply cable. Provide for equipotential bonding between the apparatus and the control cabinet. Electrical connections must be made by qualified personnel to ensure reliable operation. The contact pressure of electrical connections must be maintained during regular operation. WARNING POTENTIAL ELECTROSTATIC CHARGING HAZARD - SEE INSTRUCTIONS Precautions shall be taken to guard against any effect due to the presence of circulating current caused by stray magnetic fields. Avoid all static charge build-up on the apparatus. No air movement inside the cabinet max. coils () max. coils () charms 8 () Do not exceed the max. number of pilot solenoid valves authorised. The internal temperature of the cabinet may not exceed the minimum and maximum tempreatures specified on the product. Do not disassemble any component of the device except when replacing spare parts. The specifications of IP5 or IP65 must be met when installing the device in the cabinet. ASSEMBLY IN ATEX Ex e COMPLIANT CONTROL CABINET 0GB-07/R0 Fieldbus V DC power supply 580 Series Pressure supply Output to actuators Fielbus Electronics -

20 50-50 How to Order Manifold assemblies kit (Electronic + End plate) 5-DIGIT PRODUCT CODE G 50 A V 8 B 0 0 V A6 Thread connection ATEX options G = ISO 8/ 8 = NPT (contact us) - (GD) IP65X - (GD) IP5X (G) IP5X K = Push-in connectors A6 = A00 () A = A00 () A = A00 () D6 = DRM () D = DRM () D = DRM () D8 = X () D = X () D = X () F6 = D () F8 = D () F9 = D () () Standard (no options) Product series () DIN Rail Mount 50 ( mm valve) () External pilot supply from port 50 (8 mm valve) () External pilot supply from port and DIN Rail Mount Revision letter A = Initial release Product type V = Valve Manifold Assembly Electronics End Plate Style V = Vertical 8 = 580 Fieldbus Electronics End Plate Port Size (--5) D = CHARMs Electronics 50: Used with the first digit «G» or «8»: = /8 (female thread only) Used with the first digit «K»: H = 6 x 8 mm (push-in connector) Number of Valve Stations 50: Used with the first digit «G» or «8» or «K»: B = L = V = * 7 = * A = NA/* H = 8/0* O = 5/7* V = * = 9* = /8 D = N = * X = * B = NA/* I = 9/* P = 6/8* W = * 5 = 0* (female thread or push-in connector) F = 6 P = 6* Z = 6* C = /5* J = 0/* Q = 7 X = * 6 = * Used with the first digit «K»: H = 8 R = 8* = 8* D = /6* K = /* R = 8 Y = 5* 7 = * K = 8 x 0 mm (push-in connector) J = 0 T = 0* 5 = 0* E = NA/7* L = /* S = 9* Z = 6* M = 0 x mm (push-in connector) F = 6/8* M = /5* T = 0* = 7* G = 7/9* N = /6* U = * = 8* 580 ATEX max. coils () CHARMs () Max. number of coil under voltage Fielbus Electronics * 580 CHARMs only. How to Order 580 Electronics 5-DIGIT PRODUCT CODE P 580 A E DN 0 0 7W Product series ATEX options 580 Fieldbus Electronics 7W = Standard (no options) Revision letter Connector Type A = Initial release = M Connector (push-in connector) Actuation Protocol E = Electronics DN = DeviceNet LM = IO-Link Class A ( pin) ED = EtherNet/IP DLR LM = IO-Link Class B (5 pin) EP = EtherNet/IP PN = PROFINET 50 PT = PROFIBUS-DP CH = CHARMs 50 0GB-07/R0

21 50 Thread connection R = Pad mount How to Order Valves 5-DIGIT PRODUCT CODE R 50 A B 0 M 7W F Configurator - CAD Files Voltage - class F = V DC - class F 50 Product series ATEX options 50 ( mm valve) 7W = With impulse manual operator 8L = With maintained manual operator 8A = Without manual operator Revision letter A = Initial release Actuation Electrical interface = Rubber packed M = Plug-in (with LED indicator / DC) Valve type B = Solenoid pilot Function A = x/ NO, dual -way D = x/ NC, dual -way N = 5/, Differential air return = 5/, spring return = 5/, solenoid air return 5 = 5/, W, open center to exhaust 6 = 5/, W, center closed 7 = 5/, W, open center to pressure 50 Thread connection R = Pad mount 5-DIGIT PRODUCT CODE R 50 A B 0 M 7W F Voltage - class F = V DC - class F 50 Product series ATEX options 50 (8 mm valve) 7W = With impulse manual operator () 8L = With maintained manual operator 8A = Without manual operator 0GB-07/R0 Revision letter A = Initial release Actuation = Rubber packed Valve type B = Solenoid pilot (With impulse manual operator) Function D = x/ NC, dual -way Electrical interface M = Plug-in (with LED indicator / DC) () Used external spool valves (internal/external supply configurated in the end plate kits). For internal piloting, contact us. Fielbus Electronics - 5

22 50 Thread connection H = Metric thread K = Push-in connectors How to Order Subbase 5-DIGIT PRODUCT CODE H 50 A M S B M 7W 0 Not use Interface = High flow 50 Product series ATEX options 50 ( mm valve) 7W = Standard (zone or zones -) Revision letter A = Initial release Product type M = Manifold base Z = Mid station supply F = + Solenoid Manifold Subbase Wiring option M = Plug-in Mounting S = Manifold base, stations, side port, single Z-Board M = Manifold base, stations, side port, double Z-Board Port connection B = M7 (female thread only) D =,7 x mm (5/) [push-in connector only] (Mid station supply not available) F = x 6 mm [push-in connector only] 50 5-DIGIT PRODUCT CODE G 50 A M M M 7W 0 Thread connection Not use G = ISO 8/ 8 = NPT (contact us) Interface K = Push-in connectors = Pneumatic high flow = ISO 507- (8 mm) 50 Product series ATEX options 50 (8 mm valve) 7W = Standard (zone or zones -) Revision letter A = Initial release Product type M = Manifold base Z = Mid station supply 6 - Fielbus Electronics Wiring option M = Plug-in Mounting Port connection (-) S = Manifold base, stations, side port, single Z-Board Used with the first digit «G» or «8»: M = Manifold base, stations, side port, double Z-Board = /8 (female thread only) Used with the first digit «K»: F = 6 x 8 mm [push-in connector only] H = 8 x 0 mm [push-in connector only] 0GB-07/R0

23 Sandwich shut off block (50-50 Series) Used to shut-off pressure to the valve which is mounted above it. Allows easy maintenance without the need to shut-off pressure to the whole manifold. (specified for x/ NC-NC valve) 50 Series ()()()() () (5)() 50 Series EB B P A XE () () () () EA (5) X ()()()() () (5)() XE () () EB B () P () A (5) X EA 6,5 D C 9,5,5 B 09, A! Usable only for internal pilot supply island! Pay attention to residual pressures! The valve(s) should not be energised during disassembly weight (kg) 50 0, 50 0,5 Dimensions (mm) A B C D 50 7, 50,5 7,5 8,5 0GB-07/R0 5-DIGIT PRODUCT CODE R50AY85000 Description Sandwich shut off block (double) HOW TO ORDER [ATEX options (zone or zones -)] Consult the online configurator - CAD files on: 5-DIGIT PRODUCT CODE 50 R50AY90900 Description High Flow - Sandwich shut off block Fielbus Electronics - 7

24 8 - Fielbus Electronics 0GB-07/R0