Projector CP-WU8700/CP-WX8750/CP-X8800 CP-WU8600/CP-WX8650 User's Manual (detailed) Operating Guide Technical

Transcription

1 Projector CP-WU8700/CP-WX8750/CP-X8800 CP-WU8600/CP-WX8650 User's Manual (detailed) Operating Guide Technical Supported signals for COMPUTER IN Resolution (H x V) Signal mode H. frequency V. frequency Rating (khz) (Hz) 720 x 400 TEXT VESA 640 x 480 VGA (60Hz) VESA VGA (72Hz) VESA VGA (75Hz) VESA VGA (85Hz) VESA 800 x 600 SVGA (56Hz) VESA SVGA (60Hz) VESA SVGA (72Hz) VESA SVGA (75Hz) VESA SVGA (85Hz) VESA 832 x 624 Mac 16 mode x 768 XGA (60Hz) VESA XGA (70Hz) VESA XGA (75Hz) VESA XGA (85Hz) VESA 1152 x x 864 (75Hz) VESA 1280 x 768 W-XGA (60Hz) VESA 1280 x x 800 (60Hz) VESA 1280 x 1024 SXGA (60Hz) VESA SXGA (75Hz) VESA SXGA (85Hz) VESA *1) 1366 x 768 WXGA (60Hz) VESA 1440 x 900 WXGA+ (60Hz) VESA 1600 x 900 WXGA++ (60Hz) VESA *2) 1400 x 1050 SXGA+ (60Hz) VESA *3) 1680 x 1050 WSXGA+ (60Hz) VESA 1600 x 1200 UXGA (60Hz) VESA 1920 x 1080 Full HD (60Hz) VESA *4) 1920 x 1200 W-UXGA (60Hz) Reduced Blanking VESA *1) Supported except for [WUXGA Model] *2) Only for [XGA Model] *3) Only for [WXGA Model], [WUXGA Model] *4) Only for [WUXGA Model] (continued on next page) 1

2 Supported signals Supported signals for HDMI / HDBaseT Resolution (H x V) Signal mode H. frequency V. frequency Rating (khz) (Hz) 720 x 400 TEXT VESA 640 x 480 VGA (60Hz) VESA VGA (72Hz) VESA VGA (75Hz) VESA VGA (85Hz) VESA 800 x 600 SVGA (56Hz) VESA SVGA (60Hz) VESA SVGA (72Hz) VESA SVGA (75Hz) VESA SVGA (85Hz) VESA 832 x 624 Mac 16 mode x 768 XGA (60Hz) VESA XGA (70Hz) VESA XGA (75Hz) VESA XGA (85Hz) VESA 1152 x x 864 (75Hz) VESA 1280 x 768 W-XGA (60Hz) VESA 1280 x x 800 (60Hz) VESA 1280 x 1024 SXGA (60Hz) VESA SXGA (75Hz) VESA SXGA (85Hz) VESA 1366 x 768 WXGA (60Hz) VESA 1440 x 900 WXGA+ (60Hz) VESA 1600 x 900 WXGA++ (60Hz) VESA 1400 x 1050 SXGA+ (60Hz) VESA 1680 x 1050 WSXGA+ (60Hz) VESA 1600 x 1200 UXGA (60Hz) VESA *1) 1920 x 1200 W-UXGA (60Hz) Reduced Blanking VESA *1) Only for [WUXGA Model] (continued on next page) 2

3 Supported signals Resolution (H x V) Signal mode H. frequency V. frequency Rating (khz) (Hz) 720(1440) x 480i 480i CEA 720(1440) x 576i 576i CEA 720 x 480p 480p CEA 720 x 576p 576p CEA 1280 x 720p 720p (50Hz) CEA 720p (60Hz) CEA 1920 x 1080i 1080i (50Hz) CEA 1080i (60Hz) CEA 1920 x 1080p 1080p (50Hz) CEA 1080p (60Hz) CEA (continued on next page) 3

4 Supported signals Supported signals for DisplayPort Resolution (H x V) Signal mode H. frequency V. frequency Rating (khz) (Hz) 720 x 400 TEXT VESA 640 x 480 VGA (60Hz) VESA VGA (72Hz) VESA VGA (75Hz) VESA VGA (85Hz) VESA 800 x 600 SVGA (56Hz) VESA SVGA (60Hz) VESA SVGA (72Hz) VESA SVGA (75Hz) VESA SVGA (85Hz) VESA 832 x 624 Mac 16 mode x 768 XGA (60Hz) VESA XGA (70Hz) VESA XGA (75Hz) VESA XGA (85Hz) VESA 1152 x x 864 (75Hz) VESA 1280 x 768 W-XGA (60Hz) VESA 1280 x x 800 (60Hz) VESA 1280 x 1024 SXGA (60Hz) VESA SXGA (75Hz) VESA SXGA (85Hz) VESA 1366 x 768 WXGA (60Hz) VESA 1440 x 900 WXGA+ (60Hz) VESA 1600 x 900 WXGA++ (60Hz) VESA 1400 x 1050 SXGA+ (60Hz) VESA 1680 x 1050 WSXGA+ (60Hz) VESA 1600 x 1200 UXGA (60Hz) VESA *1) 1920 x 1200 W-UXGA (60Hz) Reduced Blanking VESA *1) Only for [WUXGA Model] (continued on next page) 4

5 Supported signals Resolution (H x V) Signal mode H. frequency V. frequency Rating (khz) (Hz) 720(1440) x 480i 480i CEA 720(1440) x 576i 576i CEA 720 x 480p 480p CEA 720 x 576p 576p CEA 1280 x 720p 720p (50Hz) CEA 720p (60Hz) CEA 1920 x 1080i 1080i (50Hz) CEA 1080i (60Hz) CEA 1920 x 1080p 1080p (50Hz) CEA 1080p (60Hz) CEA (continued on next page) 5

6 Supported signals Supported signals for SDI Resolution (H x V) Signal mode H. frequency V. frequency Rating (khz) (Hz) 720 x 480i 480i SMPTE 720 x 576i 576i SMPTE 1280 x 720p 720p (50Hz) SMPTE 720p (60Hz) SMPTE 1920 x 1080i 1080i (50Hz) SMPTE 1080i (60Hz) SMPTE 1920 x 1080sf 1080i (25Hz) SMPTE 1080i (30Hz) SMPTE 1920 x 1080p 1080p (50Hz) SMPTE 1080p (60Hz) SMPTE Only support 3G-SDI Level-A signal. NOTE Be sure to check jack type, signal level, timing and resolution before connecting this projector to a PC. Some PCs may have multiple display screen modes. Use of some of these modes will not be possible with this projector. Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. The signal will be converted to the projector s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical. Automatic adjustment may not function correctly with some input signals. The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G. The illustrations in this manual are for illustrative purposes. They may differ slightly from your projector. 6

7 Connection to the ports Connection to the ports NOTICE Use the cables with straight plugs, not L-shaped ones, as the input ports of the projector are recessed. Only the signal that is input from the COMPUTER IN can be output from the MONITOR OUT port. CP-WU8600/CP-WX8650/ CP-WX8750/CP-X8800 A B CP-WU8700 A B A COMPUTER IN, B MONITOR OUT D-sub 15pin mini shrink jack <Computer signal> Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) H/V. sync. signal: TTL level (positive/negative) Composite sync. signal: TTL level <Component video signal> Video signal: Y with composite sync, Analog, 1.0±0.1Vp-p, 75Ω terminated Cb/Pb, Analog, 0.7±0.1Vp-p, 75Ω terminated Cr/Pr, Analog, 0.7±0.1Vp-p 75Ω terminated System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60, 1080p@50/60 Pin Signal Pin Signal 1 Video Red, Cr/Pr 9 (No connection) 2 Video Green, Y 10 Ground 3 Video Blue, Cb/Pb 11 (No connection) 4 (No connection) 12 A : SDA (DDC data) B : (No connection) 5 Ground 13 H. sync / Composite sync. 6 Ground Red, Ground Cr/Pr 14 V. sync. 7 Ground Green, Ground Y 15 A : SCL (DDC clock) B : (No connection) 8 Ground Blue, Ground Cb/Pb 7

8 Connection to the ports (continued) CP-WU8600/CP-WX8650/ CP-WX8750/CP-X8800 C E D CP-WU8700 C E D C HDBaseT RJ-45 jack Pin Signal Pin Signal Pin Signal 1 HDBaseT0+ 4 HDBaseT2+ 7 HDBaseT3+ 2 HDBaseT0-5 HDBaseT2-8 HDBaseT3-3 HDBaseT1+ 6 HDBaseT1- D HDMI 1, E HDMI 2 HDMI TM connector Audio signal: Linear PCM (Sampling rate; 32/44.1/48 khz) Pin Signal Pin Signal Pin Signal 1 T.M.D.S. Data2 + 8 T.M.D.S. Data0 Shield 15 SCL 2 T.M.D.S. Data2 Shield 9 T.M.D.S. Data0-16 SDA 3 T.M.D.S. Data2-10 T.M.D.S. Clock + 17 DDC/CEC Ground 4 T.M.D.S. Data T.M.D.S. Clock Shield 18 +5V Power 5 T.M.D.S. Data1 Shield 12 T.M.D.S. Clock - 19 Hot Plug Detect 6 T.M.D.S. Data1-13 CEC 7 T.M.D.S. Data Reserved (N.C. on device) 8

9 Connection to the ports (continued) CP-WU8600/CP-WX8650/ CP-WX8750/CP-X8800 F CP-WU8700 G F G F DisplayPort DisplayPort connector Pin Signal Pin Signal Pin Signal 1 Main Link Lane 3-8 GND 15 AUX CH + 2 GND 9 Main Link Lane GND 3 Main Link Lane Main Link Lane 0-17 AUX CH - 4 Main Link Lane 2-11 GND 18 Hot Plug Detect 5 GND 12 Main Link Lane Return 6 Main Link Lane CONFIG 1 20 DP_PWR 7 Main Link Lane 1-14 CONFIG 2 G VIDEO RCA jack Composite video signal, Analog, 1.0±0.1Vp-p, 75Ω terminator System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC4.43, PAL(60Hz) 9

10 Connection to the ports (continued) CP-WU8600/CP-WX8650/ CP-WX8750/CP-X8800 L I J H K CP-WU8700 L I J H K H AUDIO IN1 Ø3.5 stereo mini jack Analog, 47kΩ input impedance AUDIO IN2 I L, J R RCA jack x2 Analog, 47kΩ input impedance AUDIO OUT K Ø3.5 stereo mini jack Analog, 1kΩ output impedance L CONTROL D-sub 9pin plug * About the details of RS-232C communication, please refer to the next section. Pin Signal Pin Signal Pin Signal 1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS 3 TD 6 (No connection) 9 (No connection) 10

11 CP-WU8600/CP-WX8650/ CP-WX8750/CP-X8800 P Q Connection to the ports (continued) M N CP-WU8700 P Q M N M LAN RJ-45 jack * About the details of network communication, please refer to the Network Guide. Pin Signal Pin Signal Pin Signal 1 TX TX RX+ 6 RX- N WIRELESS PORT Only for USB wireless adapter. Pin Signal 1 +5V 2 - Data 3 + Data 4 Ground REMOTE CONTROL P IN, Q OUT Ø3.5 stereo mini jack 11

12 Connection to the ports (continued) CP-WU8600/CP-WX8650/ CP-WX8750/CP-X8800 CP-WU8700 R R SDI BNC jack SD/HD/3G-SDI signal, Digital, 0.8V±10%, 75Ω terminated S ystem: SD-SDI signal: conforming to SMPTE ST 259-C standard YCBCR 4:2:2 10-bit 480i, 576i Single link HD-SDI signal: conforming to SMPTE ST 292 standard YPBPR 4:2:2 10-bit 720p@50/60, 1080i@50/60, 1080sf@25/30 3G-SDI Level-A signal: conforming to SMPTE ST 424 standard YPBPR 4:2:2 10-bit 1080p@50/60 12

13 RS-232C Communication RS-232C Communication When the projector connects to the computer by RS-232C communication, the projector can be controlled with RS-232C commands from the computer. For details of RS-232C commands, refer to RS-232C Communication / Network command table (&22). Connection Turn off the projector and the computer. Connect the projector's CONTROL port and the computer's RS-232C port with a RS-232C cable (cross). Use the cable that fulfi lls the specifi cation shown in fi gure. Turn the computer on, and after the computer has started up turn the projector on. the COMMUNICATION TYPE to OFF in the COMMUNICATION menu of the OPTION - SERVICE menu. RS-232C CONTROL RS-232C port of the computer RS-232C cable (cross) CONTROL port of the projector CD (1) RD(2) TD (3) DTR (4) GND (5) DSR (6) RTS (7) DTS (8) RI (9) (1) (2) RD (3) TD (4) (5) GND (6) (7) RTS (8) CTS (9) 13

14 RS-232C Communication (continued) Communication settings 1. Protocol 19200bps, 8N1 2. Command format ("h" shows hexadecimal) Action Byte Number Command Header Data Header Data CRC code Packet size flag Action Type ting code L H L H L H L H L H L H <SET>Change setting to desired value [(cl)(ch)] (al) (ah) 01h 00h (bl) (bh) (cl) (ch) by [(bl)(bh)]. <GET>Read projector internal setup value [(bl) (al) (ah) 02h 00h (bl) (bh) 00h 00h (bh)]. <INCREMENT> Increment setup value BEh EFh 03h 06h 00h (al) (ah) 04h 00h (bl) (bh) 00h 00h [(bl)(bh)] by 1. <DECREMENT> Decrement setup value (al) (ah) 05h 00h (bl) (bh) 00h 00h [(bl)(bh)] by 1. <EXECUTE> Run a command [(bl)(bh)]. (al) (ah) 06h 00h (bl) (bh) 00h 00h [Header code] [Packet] [Data size] [BEh, EFh, 03h, 06h, 00h] to byte number 0 to 4. [CRC flag] For byte number 5, 6, refer to RS-232C Communication / Network command table (&19). [Action] functional code to byte number 7, 8. <SET> = [01h, 00h], <GET> = [02h, 00h], <INCREMENT> = [04h, 00h] <DECREMENT> = [05h, 00h], <EXECUTE> = [06h, 00h] Refer to the Communication command table (&above). [Type] [ting code] For byte number 9 to 12, refer to RS-232C Communication / Network command table (&19). 14

15 RS-232C Communication (continued) 3. Response code / Error code ("h" shows hexadecimal) (1) ACK reply: 06h When the projector receives the, Increment, Decrement or Execute command correctly, the projector changes the setting data for the specified item by [Type], and it returns the code. (2) NAK reply: 15h When the projector cannot understand the received command, the projector returns the error code. In such a case, check the sending code and send the same command again. (3) Error reply: 1Ch h When the projector cannot execute the received command for any reasons, the projector returns the error code. In such a case, check the sending code and the setting status of the projector. (4) Data reply: 1Dh + xxxxh When the projector receives the GET command correctly, the projector returns the response code and 2 bytes of data. NOTE For connecting the projector to your devices, please read the manual for each devices, and connect them correctly with suitable cables. Operation cannot be guaranteed when the projector receives an undefined command or data. Provide an interval of at least 40ms between the response code and any other code. The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data. Commands are not accepted during warm-up. When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, the projector returns the error code to the computer. 15

16 Command Control via the Network Command Control via the Network When the projector connects network, the projector can be controlled with RS- 232C commands from the computer with web browser. For details of RS-232C commands, refer to RS-232C Communication / Network command table (&19). NOTE If data is transferred via wireless and wired LAN at the same time, the projector may not be able to process the data correctly. Connection 1. Turn off the projector and the computer. 2. If you use wired LAN, connect the projector's LAN or HDBaseTTM port to the computer's LAN or HDBaseT port with a LAN cable. Use the cable that fulfi lls the specifi cation shown in fi gure. If you use wireless LAN, insert the USB wireless adapter into the WIRELESS port of the projector. Turn the computer on, and after the computer has started up turn the 3. projector on. LAN LAN cable (CAT-5e or greater) or For HDBaseT connection - CAT-5e or greater - shielded type (connectors included) - straight cable - single cable 16

17 Command Control via the Network Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Configure the following items from a web browser when command control is used. Port tings Network Control Port1 (Port: 23) Network Control Port2 (Port: 9715) Port open Authentication Port open Authentication Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23. Default setting is "Enable". Click the [Enable] check box for the [Authentication] setting when authentication is required. Default setting is "Disable". Click the [Enable] check box to open [Network Control Port2 (Port: 9715)] to use TCP #9715. Default setting is "Enable". Click the [Enable] check box for the [Authentication] setting when authentication is required. Default setting is "Enable". When the authentication setting is enabled, the following settings are required. Security tings Network Control Authentication Password Re-enter Authentication Password Enter the desired authentication password. Confirm this setting will be the same for [Network Control Port1 (Port: 23)] and [Network Control Port2 (Port: 9715)]. Default setting is blank. 17

18 Command Control via the Network (continued) Command control settings [TCP #23] 1. Command format Same as RS-232C communication, refer to RS-232C Communication command format. 2. Response code / Error code ("h" shows hexadecimal) Four of the response / error code used for TCP#23 are the same as RS-232C Communication (1)~(4). One authentication error reply (5) is added. (1) ACK reply : 06h Refer to RS-232C communication (&13). (2) NAK reply : 15h Refer to RS-232C communication (&13). (3) Error reply : 1Ch h Refer to RS-232C communication (&13). (4) Data reply : 1Dh + xxxxh Refer to RS-232C communication (&13). (5) Authentication error reply : 1Fh h When authentication error occurred, the projector returns the error code. [TCP #9715] 1. Command format The commands some datum are added to the head and the end of the ones of TCP#9715 are used. Header Data length RS-232C command Check sum Connection ID D 13 bytes 1 byte 1 byte [Header] 02, Fixed [Data Length] RS-232C commands byte length (0 0D, Fixed) [RS-232C commands] Refer to RS-232C Communication command format (&14). [Check Sum] This is the value to make zero on the addition of the lower 8 bits from the header to the checksum. [Connection ID] Random value from 0 to 255 (This value is attached to the reply data). NOTE Operation cannot be guaranteed when the projector receives an undefined command or data. Provide an interval of at least 40ms between the response code and any other code. Commands are not accepted during warm-up. 18

19 Command Control via the Network (continued) 2. Response code / Error code ("h" shows hexadecimal) The connection ID is attached for the TCP#23's response / error codes are used. The connection ID is same as the sending command format. (1) ACK reply: 06h + h ( h : connection ID) (2) NAK reply: 15h + h (3) Error reply: 1Ch h + h (4) Data reply: 1Dh + xxxxh + h (5) Authentication error reply: 1Fh h + h (6) Projector busy reply: 1Fh + h + h When the projector is too busy to receive the command, the projector returns the error code. In such a case, check the sending code and send the same command again. Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type authentication with an MD5 (Message Digest 5) algorithm. When the projector is connected to a LAN, a random 8 bytes will be returned if authentication is enabled. Bind this received 8 bytes and the authentication password, and digest the data with the MD5 algorithm, and add it in front of the commands to send. The following is a sample of authentication process. Authentication password: password (example) Random 8 bytes: a572f60c (example) 1) Select a projector and receive the random 8 bytes from the projector. a572f60c 2) Bind the random 8 bytes and the authentication password. a572f60cpassword 3) Digest this bound with MD5 algorithm. e3d97429adffa11bce1f d4bde 4) Add this code in front of the commands and send the data. e3d97429adffa11bce1f d4bde + [command]. 5) When the sent data is correct, the command will be performed and the reply data will be returned. Otherwise, an authentication error will be returned. NOTE As for the transmission of the second or subsequent commands, the authentication data can be omitted for the same connection. 19

20 Network Bridge Communication Network Bridge Communication This projector is equipped with NETWORK BRIDGE function. When the projector connects to the computer by wired or wireles LAN communication, an external device connected with this projector by RS-232C communication can be controlled from the computer as a network terminal. For details, see the 7. Network Bridge function in the Network Guide. NOTE If data is transferred via wireless and wired LAN at the same time, the projector may not be able to process the data correctly. Connection If you use wired LAN, connect the computer's LAN port and the projector's LAN port with a LAN cable. Use the cable that fulfi lls the specifi cation shown in fi gure. If you use wireless LAN, insert the USB wireless adapter into the projector's LAN port. Connect the projector's CONTROL port and the RS-232C port of the devices that you want to control with a RS-232C cable. Turn the computer on, and after the computer has started up turn the projector on. the COMMUNICATION TYPE to NETWORK BRIDGE in the COMMUNICATION menu of the OPTION - SERVICE menu. LAN LAN cable (CAT-5 or greater) RS-232C cable (cross) RS-232C 20

21 Network Bridge Communication Communication settings For communication setting, use the COMMUNICATION menu in the OPTION - SERVICE menu Item BAUD RATE Data length PARITY Start bit Stop bit Transmission method Condition 4800bps / 9600bps / 19200bps / 38400bps 8 bit (fixed) NONE/ODD/EVEN 1 bit (fixed) 1 bit (fixed) HALF-DUPLEX/FULL-DUPLEX NOTE For connecting the projector to your devices, please read the manual for each devices, and connect them correctly with suitable cables. Turn off the power and unplug both the projector and other devices before connecting them. For details of Transmission method, refer to 7.4 Transmission method in the Network Guide. 21

22 RS-232C Communication / Network command table RS-232C Communication / Network command table Action Type ting code Power Input Source Error Status FOCUS ZOOM LENS SHIFT - V LENS SHIFT - H LENS SHIFT CENTERING LENS MEMORY INDEX Turn off BE EF A D Turn on BE EF BA D BE EF D Get [Example return] [Off] [On] [Cool down] COMPUTER IN BE EF FE D LAN BE EF CE D B 00 HDMI 1 BE EF E D HDMI 2 BE EF E D D 00 HDBaseT BE EF AE DE VIDEO BE EF E D SDI* BE EF E DE DisplayPort BE EF CE DF Get BE EF CD D BE EF D9 D [Example return] Get [Normal] [Cover error] [Fan error] [Lamp error] [Temp error] [Air flow error] [Cold error] [Filter error] 0F [Shade error] [Lens Shift error] [AC blackout error] Increment BE EF A Decrement BE EF BB Increment BE EF Decrement BE EF Increment BE EF D Decrement BE EF Increment BE EF E Decrement BE EF FF Execute BE EF B BE EF B BE EF DB BE EF B Get BE EF LENS MEMORY LOAD Execute BE EF E LENS MEMORY SAVE Execute BE EF LENS MEMORY CLEAR Execute BE EF A * Supported only for CP-WU

23 RS-232C Communication / Network command table (continued) LENS MEMORY LENS SHIFT - V LENS MEMORY LENS SHIFT - H LENS MEMORY LENS TYPE MAGNIFY MAGNIFY Position H MAGNIFY Position V FREEZE SHADE PbyP/PinP PbyP MAIN SIZE PbyP RIGHT SOURCE PbyP MAIN AREA PbyP LEFT SOURCE Action Type ting code Get BE EF A D Get BE EF E E Get BE EF F Get BE EF C D Increment BE EF A D Decrement BE EF CB D Get BE EF C8 D Increment BE EF AE D Decrement BE EF F D Get BE EF D Increment BE EF D Decrement BE EF D NORMAL BE EF D FREEZE BE EF D Get BE EF B0 D OFF BE EF F ON BE EF Get BE EF C OFF BE EF E PbyP BE EF AE PinP BE EF E Get BE EF D SMALL BE EF F F 00 MIDDLE BE EF LARGE BE EF Get BE EF F COMPUTER IN BE EF HDMI 1 BE EF HDMI 2 BE EF D 00 HDBaseT BE EF D6 2B VIDEO BE EF SDI* BE EF B DisplayPort BE EF B6 2A Get BE EF B LEFT BE EF A RIGHT BE EF EA Get BE EF COMPUTER IN BE EF F HDMI 1 BE EF HDMI 2 BE EF D 00 HDBaseT BE EF A2 2A VIDEO BE EF SDI* BE EF A DisplayPort BE EF C2 2B Get BE EF C * Supported only for CP-WU8700 (continued on next page) 23

24 RS-232C Communication / Network command table (continued) PinP POSITION PinP MAIN AREA PinP PRIMARY SOURCE PinP SECONDARY SOURCE Action Type ting code TOP LEFT BE EF TOP RIGHT BE EF BOTTOM LEFT BE EF BOTTOM RIGHT BE EF F Get BE EF PRIMARY BE EF SECONDARY BE EF A Get BE EF COMPUTER IN BE EF CE HDMI 1 BE EF E HDMI 2 BE EF E D 00 HDBaseT BE EF E 2F VIDEO BE EF E SDI* BE EF E 2F DisplayPort BE EF FE 2E Get BE EF FD COMPUTER IN BE EF HDMI 1 BE EF B HDMI 2 BE EF D D 00 HDBaseT BE EF F VIDEO BE EF D SDI* BE EF E6 2F DisplayPort BE EF E Get BE EF PbyP/PinP SWAP Execute BE EF LEFT / PRIMARY BE EF A PbyP / PinP RIGHT / SECONDARY BE EF DA FRAME LOCK Get BE EF PICTURE MODE * Supported only for CP-WU8700 STANDARD BE EF F BA NATURAL BE EF F BA CINEMA BE EF B3 F BA DYNAMIC BE EF E3 F BA BOARD(BLACK) BE EF E3 EF BA BOARD(GREEN) BE EF EE BA WHITEBOARD BE EF EE BA DAYTIME BE EF E3 C BA DICOM SIM. BE EF C BA USER-1 BE EF E3 FB BA USER-2 BE EF FA BA USER-3 BE EF FA BA BE EF F BA [Example return] Get [NORMAL] [CINEMA] [DYNAMIC] [BOARD(BLACK)] [BOARD(GREEN)] [WHITEBOARD] [DAY TIME] [DICOM SIM.] [Custom] 24 (continued on next page)

25 RS-232C Communication / Network command table (continued) Action Type ting code BRIGHTNESS BRIGHTNESS Reset CONTRAST CONTRAST Reset GAMMA User GAMMA Point 1 User GAMMA Point 1 Reset User GAMMA Point 2 User GAMMA Point 2 Reset User GAMMA Point 3 User GAMMA Point 3 Reset Get BE EF D Increment BE EF EF D Decrement BE EF E D Execute BE EF D Get BE EF FD D Increment BE EF B D Decrement BE EF A D Execute BE EF A4 D DEFAULT BE EF E A CUSTOM BE EF FD A DEFAULT BE EF E A CUSTOM BE EF FC A DEFAULT BE EF E A CUSTOM BE EF FC A DEFAULT BE EF F7 E A CUSTOM BE EF F7 FD A DEFAULT BE EF C7 EB A CUSTOM BE EF C7 FF A DEFAULT BE EF EA A CUSTOM BE EF FE A DEFAULT BE EF A7 EA A CUSTOM BE EF A7 FE A DEFAULT BE EF EB A CUSTOM BE EF FF A Get BE EF F4 F A Get BE EF FE Increment BE EF E FE Decrement BE EF BF FF Execute BE EF C Get BE EF F4 FF Increment BE EF FF Decrement BE EF FE Execute BE EF A4 C Get BE EF B0 FF Increment BE EF D6 FF Decrement BE EF FE Execute BE EF E0 C (continued on next page) 25

26 RS-232C Communication / Network command table (continued) Action Type ting code User GAMMA Point 4 User GAMMA Point 4 Reset User GAMMA Point 5 User GAMMA Point 5 Reset User GAMMA Point 6 User GAMMA Point 6 Reset User GAMMA Point 7 User GAMMA Point 7 Reset User GAMMA Point 8 User GAMMA Point 8 Reset TEMP Get BE EF C FE Increment BE EF A FE Decrement BE EF FB FF Execute BE EF C C Get BE EF FF Increment BE EF E FF Decrement BE EF F FE Execute BE EF C Get BE EF C4 FE Increment BE EF A2 FE Decrement BE EF FF Execute BE EF C Get BE EF FE Increment BE EF E6 FE Decrement BE EF FF Execute BE EF D0 C Get BE EF C FF Increment BE EF A FF Decrement BE EF CB FE Execute BE EF C C HIGH BE EF B F B CUSTOM(HIGH) BE EF CB F B MID-1 BE EF B F B CUSTOM(MID-1) BE EF B F B MID-2 BE EF B F B CUSTOM (MID- 2) BE EF FB FA B LOW BE EF B F B CUSTOM(LOW) BE EF AB F B Hi-BRIGHT-1 BE EF B F B CUSTOM BE EF FB FF B Hi-BRIGHT-2 BE EF AB F B CUSTOM BE EF B FE B Hi-BRIGHT-3 BE EF B F B0 30 0A 00 7 CUSTOM BE EF B FE B0 30 1A 00 Get BE EF C8 F B (continued on next page)

27 RS-232C Communication / Network command table (continued) TEMP GAIN R TEMP GAIN R Reset TEMP GAIN G TEMP GAIN G Reset TEMP GAIN B TEMP GAIN B Reset TEMP OFFSET R TEMP OFFSET R Reset TEMP OFFSET G TEMP OFFSET G Reset TEMP OFFSET B TEMP OFFSET B Reset Action Type ting code Get BE EF F B Increment BE EF F B Decrement BE EF F B Execute BE EF C Get BE EF F B Increment BE EF F B Decrement BE EF C7 F B Execute BE EF EC C Get BE EF C F B Increment BE EF EA F B Decrement BE EF B F B Execute BE EF F8 C Get BE EF F B Increment BE EF F B Decrement BE EF B3 F B Execute BE EF C A Get BE EF F B Increment BE EF F B Decrement BE EF F7 F B Execute BE EF BC C B Get BE EF BC F B Increment BE EF DA F B Decrement BE EF B F B Execute BE EF C8 C C Get BE EF B Increment BE EF D Decrement BE EF Reset Execute BE EF D A (continued on next page) 27

28 RS-232C Communication / Network command table (continued) TINT 28 (continued on next page) Action Type ting code Get BE EF Increment BE EF F Decrement BE EF FE TINT Reset Execute BE EF C D B Get BE EF F SHARPNESS Increment BE EF Decrement BE EF SHARPNESS Reset ACCENTUALIZER ACCENTUALIZER Reset HDCR Execute BE EF C4 D Get BE EF D C Increment BE EF B C Decrement BE EF EA C Execute BE EF C8 DB C Get BE EF A D Increment BE EF C D Decrement BE EF D HDCR Reset Execute BE EF DA D OFF BE EF B ACTIVE IRIS THEATER BE EF CB 2F PRESENTATION BE EF B 2E Get BE EF MY MEMORY Load MY MEMORY Save ASPECT OVER SCAN OVER SCAN Reset V POSITION V POSITION Reset 1 BE EF E D BE EF E D BE EF E D BE EF FE D BE EF F2 D BE EF D BE EF D BE EF D NORMAL BE EF E DD :3 BE EF E D :9 BE EF E D :10 BE EF E D A 00 14:9 BE EF CE D NATIVE * BE EF E D Get BE EF AD D Get BE EF Increment BE EF F Decrement BE EF Execute BE EF EC D Get BE EF D Increment BE EF B Decrement BE EF BA Execute BE EF E0 D * Only for CP-WU8600/CP-WX8650/CP-WU8700/CP-WX8750

29 RS-232C Communication / Network command table (continued) Action Type ting code H POSITION Get BE EF F Increment BE EF Decrement BE EF H POSITION Reset H PHASE H SIZE Execute BE EF C D Get BE EF Increment BE EF F Decrement BE EF FE Get BE EF B Increment BE EF D Decrement BE EF H SIZE Reset Execute BE EF D AUTO ADJUST EXECUTE PROGRESSIVE VIDEO NR SPACE C-VIDEO FORMAT HDMI 1 FORMAT HDMI 2 FORMAT Execute BE EF D A OFF BE EF A TV BE EF DA FILM BE EF A Get BE EF LOW BE EF MID BE EF D HIGH BE EF Get BE EF AUTO BE EF E RGB BE EF E SMPTE240 BE EF E REC709 BE EF FE REC601 BE EF CE Get BE EF D AUTO BE EF A A 00 NTSC BE EF C PAL BE EF SECAM BE EF NTSC4.43 BE EF M-PAL BE EF C N-PAL BE EF Get BE EF AUTO BE EF BA VIDEO BE EF A COMPUTER BE EF DA Get BE EF AUTO BE EF D VIDEO BE EF C D COMPUTER BE EF D Get BE EF D (continued on next page) 29

30 RS-232C Communication / Network command table (continued) Action Type ting code HDBaseT FORMAT DisplayPort FORMAT HDMI 1 RANGE HDMI 2 RANGE HDBaseT RANGE SDI RANGE* DisplayPort RANGE AUTO BE EF A EA D VIDEO BE EF EA EB D COMPUTER BE EF A EB D Get BE EF EA D AUTO BE EF BA E F VIDEO BE EF A E F COMPUTER BE EF DA E F Get BE EF E F AUTO BE EF D NORMAL BE EF D ENHANCED BE EF E6 D Get BE EF B5 D AUTO BE EF A D NORMAL BE EF EA D ENHANCED BE EF A D Get BE EF D AUTO BE EF EB D NORMAL BE EF EA D ENHANCED BE EF E6 EA D Get BE EF B5 EB D NORMAL BE EF E E ENHANCED BE EF E6 E E Get BE EF B5 E E AUTO BE EF E F NORMAL BE EF D6 E F ENHANCED BE EF E F Get BE EF E F COMPUTER IN AUTO BE EF CE D SYNC ON G OFF BE EF E D Get BE EF D D FRAME LOCK - COMPUTER IN FRAME LOCK - HDMI 1 FRAME LOCK - HDMI 2 FRAME LOCK - HDBaseT * Supported only for CP-WU8700 OFF BE EF B C ON BE EF AB C Get BE EF C OFF BE EF F C ON BE EF EF C Get BE EF C C OFF BE EF C D ON BE EF C D Get BE EF A4 C D OFF BE EF C2 EB D ON BE EF EA D Get BE EF F1 EB D (continued on next page)

31 RS-232C Communication / Network command table (continued) Action Type ting code FRAME LOCK - SDI* FRAME LOCK - DisplayPort PICTURE POSITION V PICTURE POSITION H GEOMETRIC MODE KEYSTONE V KEYSTONE V Reset KEYSTONE H KEYSTONE H Reset PERFECT FIT Left Top - H PERFECT FIT Left Top - V PERFECT FIT Right Top - H PERFECT FIT Right Top - V * Supported only for CP-WU8700 OFF BE EF C2 E E ON BE EF E E Get BE EF F1 E E OFF BE EF E F ON BE EF E F Get BE EF E F TOP BE EF D MIDDLE BE EF D BOTTOM BE EF F2 D Get BE EF D RIGHT BE EF D E MIDDLE BE EF D6 D E LEFT BE EF B6 D E Get BE EF E5 D E KEYSTONE BE EF B 8C PERFECT FIT BE EF B 8C WARPING BE EF B 8F Get BE EF C8 8D Get BE EF B9 D Increment BE EF DF D Decrement BE EF E D Execute BE EF D C Get BE EF E9 D B Increment BE EF F D B Decrement BE EF E D B Execute BE EF D Get BE EF Increment BE EF Decrement BE EF Get BE EF Increment BE EF Decrement BE EF C Get BE EF Increment BE EF EF Decrement BE EF E Get BE EF FD Increment BE EF B Decrement BE EF A (continued on next page) 31

32 RS-232C Communication / Network command table (continued) Action Type ting code PERFECT FIT Left Bottom - H PERFECT FIT Left Bottom - V PERFECT FIT Right Bottom - H PERFECT FIT Right Bottom - V PERFECT FIT All Corners Reset PERFECT FIT Left Side Distortion PERFECT FIT Right Side Distortion PERFECT FIT Top Side Distortion PERFECT FIT Bottom Side Distortion PERFECT FIT All Sides Reset PERFECT FIT Memory Save-1 PERFECT FIT Memory Save-2 PERFECT FIT Memory Save-3 PERFECT FIT Memory Load-1 PERFECT FIT Memory Load-2 PERFECT FIT Memory Load-3 Get BE EF Increment BE EF Decrement BE EF B Get BE EF Increment BE EF Decrement BE EF F Get BE EF B Increment BE EF DF Decrement BE EF E Get BE EF AD 8A Increment BE EF CB 8A Decrement BE EF A 8B Execute BE EF D5 8A Get BE EF Increment BE EF Decrement BE EF Get BE EF Increment BE EF Decrement BE EF C Get BE EF FD Increment BE EF B Decrement BE EF A Get BE EF Increment BE EF Decrement BE EF B Execute BE EF D Execute BE EF Execute BE EF D Execute BE EF A Execute BE EF D B Execute BE EF C Execute BE EF E D (continued on next page)

33 RS-232C Communication / Network command table (continued) Action Type ting code EDGE BLENDING MODE EDGE BLENDING REGION Reset EDGE BLENDING LEVEL EDGE BLENDING LEFT EDGE BLENDING RIGHT EDGE BLENDING TOP EDGE BLENDING BOTTOM OFF BE EF B C MANUAL BE EF FB C CAMERA BE EF B C Get BE EF C Execute BE EF C Increment BE EF Decrement BE EF Get BE EF F Get BE EF Increment BE EF E Decrement BE EF DF Get BE EF Increment BE EF F Decrement BE EF Get BE EF D A Increment BE EF B A Decrement BE EF A Get BE EF C B Increment BE EF A B Decrement BE EF B B (continued on next page) 33

34 RS-232C Communication / Network command table (continued) CROPPING MODE CROPPING SETUP X CROPPING SETUP Y CROPPING SETUP W CROPPING SETUP H Action Type ting code OFF BE EF FB ON BE EF B Get BE EF C Get BE EF A Increment BE EF CE Decrement BE EF F Get BE EF Increment BE EF Decrement BE EF E Get BE EF A Increment BE EF A Decrement BE EF A A Get BE EF EC B Increment BE EF A B Decrement BE EF B B CROPPING Apply Execute BE EF B CROPPING Reset Execute BE EF F OFF BE EF FB 9C MODE-1 BE EF B 9D WARPING MODE-2 BE EF B 9D MODE MODE-3 BE EF B 9C Get BE EF C8 9C DIMMING LEVEL WHITE BALANCE OFFSET R WHITE BALANCE OFFSET R Reset WHITE BALANCE OFFSET G WHITE BALANCE OFFSET G REset WHITE BALANCE OFFSET B WHITE BALANCE OFFSET B Reset Get BE EF C Increment BE EF A Decrement BE EF CB Get BE EF C Increment BE EF A Decrement BE EF BB Execute BE EF E F Get BE EF F Increment BE EF Decrement BE EF Execute BE EF C4 E F Get BE EF B Increment BE EF D Decrement BE EF Execute BE EF E FA (continued on next page)

35 RS-232C Communication / Network command table (continued) WHITE BALANCE GAIN R WHITE BALANCE GAIN R Reset WHITE BALANCE GAIN G WHITE BALANCE GAIN G Reset WHITE BALANCE GAIN B WHITE BALANCE GAIN B Reset BLACK LEVEL R BLACK LEVEL R Reset BLACK LEVEL G BLACK LEVEL G Reset BLACK LEVEL B BLACK LEVEL B Reset BLACK LEVEL W BLACK LEVEL W Reset Action Type ting code Get BE EF C Increment BE EF A Decrement BE EF B Execute BE EF E FC Get BE EF C Increment BE EF A Decrement BE EF Execute BE EF F4 E FD Get BE EF Increment BE EF E Decrement BE EF Execute BE EF B0 E FE Get BE EF CC Increment BE EF AA Decrement BE EF B Execute BE EF E F Get BE EF Increment BE EF Decrement BE EF Execute BE EF E F Get BE EF Increment BE EF Decrement BE EF C Execute BE EF D0 E F Get BE EF Increment BE EF EE Decrement BE EF F Execute BE EF C E F (continued on next page) 35

36 RS-232C Communication / Network command table (continued) Action Type ting code IMAGE OPTIMIZER ECO MODE INSTALLATION STANDBY MODE UNIFORMITY LEVEL UNIFORMITY AREA UNIFORMITY R UNIFORMITY R Reset UNIFORMITY G UNIFORMITY G Reset UNIFORMITY B UNIFORMITY B Reset OFF BE EF D E ON BE EF E Get BE EF E E NORMAL BE EF B ECO BE EF AB Get BE EF FRONT / DESKTOP BE EF C7 D REAR / DESKTOP BE EF D REAR / CEILING BE EF A7 D FRONT / CEILING BE EF D Get BE EF F4 D NORMAL BE EF D6 D SAVING BE EF D Get BE EF E5 D BE EF AF 6D BE EF F 6D BE EF CF 6C BE EF FF 6E Get BE EF C 6C Top Left BE EF C3 6D Top BE EF C Top Right BE EF A3 6C Left BE EF AC All BE EF AD Right BE EF AD Bottom Left BE EF EC Bottom BE EF ED Bottom Right BE EF ED Get BE EF F0 6D Get BE EF B4 6D Increment BE EF D2 6D Decrement BE EF C Execute BE EF E F Get BE EF C Increment BE EF E 6C Decrement BE EF FF 6D Execute BE EF A4 E F Get BE EF C 6D Increment BE EF A 6D Decrement BE EF B 6C Execute BE EF E0 E F (continued on next page)