Digital Projector X95i Operator's Guide

Transcription

1 Digital Projector X95i Operator's Guide TECHNICAL Example of computer signal Resolution (H x V) H. frequency (khz) V. frequency (Hz) Rating Signal mode 720 x VESA TEXT 640 x VESA VGA (60Hz) 640 x VESA VGA (72Hz) 640 x VESA VGA (75Hz) 640 x VESA VGA (85Hz) 800 x VESA SVGA (56Hz) 800 x VESA SVGA (60Hz) 800 x VESA SVGA (72Hz) 800 x VESA SVGA (75Hz) 800 x VESA SVGA (85Hz) 832 x Mac 16 mode 1024 x VESA XGA (60Hz) 1024 x VESA XGA (70Hz) 1024 x VESA XGA (75Hz) 1024 x VESA XGA (85Hz) 1152 x VESA 1152 x 864 (75Hz) 1280 x VESA 1280 x 960 (60Hz) 1280 x VESA SXGA (60Hz) 1280 x VESA SXGA (75Hz) *1280 x VESA SXGA (85Hz) *1600 x VESA UXGA (60Hz) 1280 x VESA W-XGA (60Hz) 1400 x VESA SXGA+ (60Hz) 1280 x VESA 1280 x 800 (60Hz) NOTE Be sure to check jack type, signal level, timing and resolution before connecting this projector to a computer. Some computers may have multiple display screen modes. Use of some of these modes will not be possible with this projector. Depending on the input signal, full-size display may not be possible in some cases. Refer to the number of display pixels above. Although the projector can display signals with resolution up to UXGA (1600x1200), the signal will be converted to the projector s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and projector panel are identical. Automatic adjustment may not function correctly with some input signals. The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G. The HDMI input does not support the signals marked with *. 3M All Rights Reserved. 1

2 Initial set signals Initial set signals The following signals are used for the initial settings. The signal timing of some computer models may be different. In such case, adjust the items V POSITION and H POSITION in the IMAGE menu. Back porch (B) Front porch (D) Back porch (b) Front porch (d) Display interval (C) Display interval (c) Data Data H. Sync. V. Sync. Sync (A) Sync (a) Computer/ Horizontal signal timing (μs) Computer/ Vertical signal timing (lines) Signal (A) (B) (C) (D) Signal (a) (b) (c) (d) TEXT TEXT VGA (60Hz) VGA (60Hz) VGA (72Hz) VGA (72Hz) VGA (75Hz) VGA (75Hz) VGA (85Hz) VGA (85Hz) SVGA (56Hz) SVGA (56Hz) SVGA (60Hz) SVGA (60Hz) SVGA (72Hz) SVGA (72Hz) SVGA (75Hz) SVGA (75Hz) SVGA (85Hz) SVGA (85Hz) Mac 16" mode Mac 16" mode XGA (60Hz) XGA (60Hz) XGA (70Hz) XGA (70Hz) XGA (75Hz) XGA (75Hz) XGA (85Hz) XGA (85Hz) x x (75Hz) (75Hz) x x (60Hz) (60Hz) SXGA (60Hz) SXGA(60Hz) SXGA (75Hz) SXGA (75Hz) SXGA (85Hz) SXGA (85Hz) UXGA (60Hz) UXGA (60Hz) W-XGA (60Hz) W-XGA (60Hz) SXGA+ (60Hz) SXGA+ (60Hz) x 800(60Hz) x 800(60Hz) M All Rights Reserved.

3 Connection to the ports Connection to the ports D B SD CARD A AUX I/O DC 5V 0.5A C LAN RGB1 HDMI RGB OUT VIDEO Y CB/PB CR/PR AUDIO IN1 AUDIO IN2 RGB2 G/Y B/CB/PB R/CR/PR S-VIDEO R L R L AUDIO IN3 AUDIO IN4 AUDIO OUT REMOTE CONTROL H V USB CONTROL A RGB 1, B RGB OUT D-sub 15pin mini shrink jack Video signal: RGB separate, Analog, 0.7Vp-p, 75Ω terminated (positive) H/V. sync. signal: TTL level (positive/negative) Composite sync. signal: TTL level At RGB signal Pin Signal Pin Signal 1 Video Red 9 (No connection) 2 Video Green 10 Ground 3 Video Blue 11 (No connection) 4 (No connection) 12 A : SDA (DDC data), B : (No connection) 5 Ground 13 H. sync / Composite sync. 6 Ground Red 14 V. sync. 7 Ground Green 15 A : SCL (DDC clock), B : (No connection) 8 Ground Blue C RGB 2(G/Y, B/CB/PB, R/CR/PR, H, V) BNC jack x 5 Video : Analog 0.7Vp-p, 75Ω terminator H/V, sync, : TTL level (positive/negative) Composite sync, : TTL level D HDMI Type :Digital audio/video connector Audio signal : Linear PCM (Sampling rate; 32/44.1/48 khz) Pin Signal Pin Signal Pin Signal 1 T.M.D.S. Data2 + 8 T.M.D.S. Data0 Shield 15 SCL 2 T.M.D.S. Data2 Shield 9 T.M.D.S. Data0-16 SDA 3 T.M.D.S. Data2-10 T.M.D.S. Clock + 17 DDC/CEC Ground 4 T.M.D.S. Data T.M.D.S. Clock Shield 18 +5V Power 5 T.M.D.S. Data1 Shield 12 T.M.D.S. Clock - 19 Hot Plug Detect 6 T.M.D.S. Data1-13 CEC 7 T.M.D.S. Data Reserved(N.C. on device) 5 3M All Rights Reserved. 3

4 SD CARD Connection to the ports (continued) AUX I/O DC 5V 0.5A I E F G LAN RGB1 HDMI RGB OUT VIDEO Y CB/PB CR/PR AUDIO IN1 AUDIO IN2 H RGB2 G/Y B/CB/PB R/CR/PR S-VIDEO R L R L AUDIO IN3 AUDIO IN4 AUDIO OUT REMOTE CONTROL H V USB CONTROL COMPONENT VIDEO E Y, F CB/PB, G CR/PR RCA jack x3 System: 480i@60, 480p@60, 576i@50, 720p@50/60, 1080i@50/60,1080p@50/60 Port Y CB/PB CR/PR Signal Component video Y, 1.0±0.1Vp-p, 75Ω terminator with composite sync Component video CB/PB, 0.7±0.1Vp-p, 75Ω terminator Component video CR/PR, 0.7±0.1Vp-p, 75Ω terminator H S-VIDEO Mini DIN 4pin jack Pin Signal Color signal 0.286Vp-p (NTSC, burst), 75Ω terminator 1 Color signal 0.300Vp-p (PAL/SECAM, burst) 75Ω terminator 2 Brightness signal, 1.0Vp-p, 75Ω terminator 3 Ground 4 Ground I VIDEO RCA jack System: NTSC, PAL, SECAM, PAL-M, PAL-N, NTSC ±0.1Vp-p, 75Ω terminator 4 3M All Rights Reserved.

5 SD CARD Connection to the ports (continued) J HDMI K AUDIO IN1 AUDIO IN2 AUX I/O DC 5V 0.5A RGB1 L RGB YM NCB/PB O P Q S R OUT VIDEO CR/PR LAN RGB2 G/Y B/CB/PB R/CR/PR S-VIDEO R L R L AUDIO IN3 AUDIO IN4 AUDIO OUT REMOTE CONTROL H V USB CONTROL J AUDIO IN 1, K AUDIO IN 2 Ø3.5 stereo mini jack 500 mvrms 47kΩ terminator AUDIO IN 3 L R, M L, AUDIO IN 4 N R, O L RCA jack x2 500 mvrms 47kΩ terminator P AUDIO OUT Ø3.5 stereo mini jack 500 mvrms 1kΩ output impedance Q REMOTE CONTROL Ø3.5 stereo mini jack To be connected with the remote control that came with the projector. R CONTROL D-sub 9pin plug About the details of RS-232C communication, please refer to the following RS-232C Communication in this manual. Pin Signal Pin Signal Pin Signal 1 (No connection) 4 (No connection) 7 RTS 2 RD 5 Ground 8 CTS 3 TD 6 (No connection) 9 (No connection) S USB USB B type jack Pin Signal 1 +5V 2 - Data 3 + Data 4 Ground 3M All Rights Reserved. 5

6 SD CARD Connection to the ports (continued) V U T AUX I/O DC 5V 0.5A LAN RGB1 HDMI RGB OUT VIDEO Y CB/PB CR/PR AUDIO IN1 AUDIO IN2 RGB2 G/Y B/CB/PB R/CR/PR S-VIDEO R L R L AUDIO IN3 AUDIO IN4 AUDIO OUT REMOTE CONTROL H V USB CONTROL T LAN RJ-45 jack Pin Signal Pin Signal Pin Signal 1 TX TX RX+ 6 RX- U AUX I/O USB A type jack Pin Signal 1 +5V 2 - Data 3 + Data 4 Gtound V SD card slot SD card slot Pin Signal Pin Signal Pin Signal 1 CD/DAT 3 4 VDD 7 DAT 0 2 CMD 5 CLK 8 DAT 1 3 VSS 6 VSS 9 DAT M All Rights Reserved.

7 RS-232C Communication RS-232C Communication CONTROL port RS-232C cable (Cross) RS-232C port of the projector of the computer - (1) (1) CD RD (2) (2) RD TD (3) (3) TD - (4) (4) DTR GND (5) (5) GND - (6) (6) DSR RTS (7) (7) RTS CTS (8) (8) DTS - (9) (9) RI Connecting the cable Turn off the projector and the computer. Connect the CONTROL port of the projector with a RS-232C port of the computer by a RS-232C cable (cross). Use the cable that fulfills the specification shown in the previous page. 3. Turn the computer on, and after the computer has started up turn the projector on. Communications setting 19200bps, 8N1 1. Protocol Consist of header (7 bytes) + command data (6 bytes). 2. Header BE + EF CRC_low + CRC_high CRC_low : Lower byte of CRC flag for command data CRC_high : Upper byte of CRC flag for command data 3. Command data Command data chart byte_0 byte_1 byte_2 byte_3 byte_4 byte_5 Action Type Setting code low high low high low high Action (byte_0-1) Action Classification Content 1 SET Change setting to desired value. 2 GET Read projector internal setup value. 4 INCREMENT Increment setup value by 1. 5 DECREMENT Decrement setup value by 1. 6 EXECUTE Run a command. 3M All Rights Reserved. 7

8 RS-232C Communication (continued) Requesting projector status (Get command) (1) Send the request code Header + Command data ( 02H + 00H + type (2 bytes)+ 00H + 00H ) from the computer to the projector. (2) The projector returns the response code 1DH + data (2 bytes) to the computer. Changing the projector settings (Set command) (1) Send the setting code Header + Command data ( 01H + 00H + type (2 bytes) + setting code (2 bytes)) from the computer to the projector. (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code 06H to the computer. Using the projector default settings (Reset Command) (1) The computer sends the default setting code Header + Command data ( 06H + 00H + type (2 bytes) + 00H + 00H ) to the projector. (2) The projector changes the specified setting to the default value. (3) The projector returns the response code 06H to the computer. Increasing the projector setting value (Increment command) (1) The computer sends the increment code Header + Command data ( 04H + 00H + type (2 bytes) + 00H + 00H ) to the projector. (2) The projector in creases the setting value on the above setting code. (3) The projector returns the response code 06H to the computer. Decreasing the projector setting value (Decrement command) (1) The computer sends the decrement code Header + Command data ( 05H + 00H + type (2 bytes) + 00H + 00H ) to the projector. (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code 06H to the computer. When the projector cannot understand the received command When the projector cannot understand the received command, the error code 15H is sent back to the computer. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code 15H is sent back to the computer. If this error code is returned, send the same command again. When the projector cannot execute the received command. When the projector cannot execute the received command, the error code 1CH + xxxxh is sent back to the computer. When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, an error code will be returned to the computer. NOTE Operation cannot be guaranteed when the projector receives an undefined command or data. Provide an interval of at least 40ms between the response code and any other code. The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data. Commands are not accepted during warm-up. 8 3M All Rights Reserved.

9 Command Control via the Network Command Control via the Network Communication Port The following two ports are assigned for the command control. TCP #23 TCP #9715 Command Control Settings Configure the following items form a web browser when command control is used. Port Settings Network Control Port1 (Port: 23) Network Control Port2 (Port: 9715) Port open Authentication Port open Authentication Click the [Enable] check box to open [Network Control Port1 (Port: 23)] to use TCP #23. Default setting is Enable. Click the [Enable] check box for the [Authentication] setting when authentication is required. Default setting is Disable. Click the [Enable] check box to open [Network Control Port2 (Port: 9715)] to use TCP #9715. Default setting is Enable. Click the [Enable] check box for the [Authentication] setting when authentication is required. Default setting is Enable. When the authentication setting is enabled, the following settings are required. Security Settings Network Control Authentication Password Re-enter Authentication Password Enter the desired authentication password. This setting will be the same for [Network Control Port1 (Port: 23)] and [Network Control Port2 (Port: 9715)]. Default setting is blank. 3M All Rights Reserved. 9

10 Command Control via the Network (continued) Command Format [TCP #23] 1. Protocol Consist of header (7 bytes) + command data (6 bytes) 2. Header BE + EF CRC_low + CRC_high CRC_low: Lower byte of CRC flag for command data CRC_high: Upper byte of CRC flag for command data 3. Command data Command data chart byte_0 byte_1 byte_2 byte_3 byte_4 byte_5 Action Type Setting code low high low high low high Action (byte_0-1) Action Classification Content 1 Set Change setting to desired value. 2 Get Read projector internal setup value. 4 Increment Increment setup value by 1. 5 Decrement Decrement setup value by 1. 6 Execute Run a command. Requesting projector status (Get command) (1) Send the following request code from the PC to the projector. Header + Command data ( 02H + 00H + type (2 bytes) + 00H + 00H ) (2) The projector returns the response code 1DH + data (2 bytes) to the PC. Changing the projector settings (Set command) (1) Send the following setting code from the PC to the projector. Header + Command data ( 01H + 00H + type (2 bytes) + setting code (2 bytes)) (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code 06H to the PC. Using the projector default settings (Reset Command) (1) The PC sends the following default setting code to the projector. Header + Command data ( 06H + 00H + type (2 bytes) + 00H + 00H ) (2) The projector changes the specified setting to the default value. (3) The projector returns the response code 06H to the PC. Increasing the projector setting value (Increment command) (1) The PC sends the following increment code to the projector. Header + Command data ( 04H + 00H + type (2 bytes) + 00H + 00H ) (2) The projector increases the setting value on the above setting code. (3) The projector returns the response code 06H to the PC. 10 3M All Rights Reserved.

11 Command Control via the Network (continued) Decreasing the projector setting value (Decrement command) (1) The PC sends the following decrement code to the projector. Header + Command data ( 05H + 00H + type (2 bytes) + 00H + 00H ) (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code 06H to the PC. When the projector cannot understand the received command When the projector cannot understand the received command, the error code 15H is sent back to the PC. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code 15H is sent back to the PC. If this error code is returned, send the same command again. When the projector cannot execute the received command. When the projector cannot execute the received command, the error code 1CH + xxxxh is sent back to the PC. When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, an error code will be returned to the PC. When authentication error occurred. When authentication error occurred, the error code the 1FH H is sent back to the PC. NOTE Operation cannot be guaranteed when the projector receives an undefined command or data. Provide an interval of at least 40ms between the response code and any other code. Commands are not accepted during warm-up. [TCP #9715] 1. Protocol Consist of header (1 byte) + data length (1 byte) + command data (13 bytes) + check sum (1 bytes) + connection ID (1 byte). 2. Header 02, Fixed 3. Data Length Network control commands byte length (0D, Fixed) 4. Command data Network control commands that start with BE EF (13bytes). 5. Check Sum This is the value to make zero on the addition of the lower 8 bits from the header to the checksum. 6. Connection ID Random value from 0 to 255 (This value is attached to the reply data). 3M All Rights Reserved. 11

12 Command Control via the Network (continued) 7. Reply Data The connection ID (the data is same as the connection ID data on the sending data format) is attached to the Network control commands reply data. ACK reply: 06H + xxh NAK reply: 15H + xxh Error reply: 1CH + xxxxh + xxh Data reply: 1DH + xxxxh + xxh Projector busy reply: 1FH + xxxxh + xxh Authentication error reply: 1FH H + xxh ( xxh : connection ID) Automatic Connection Break The TCP connection will be automatically disconnected after there is no communication for 30 seconds after being established. Authentication The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type authentication with an MD5 (Message Digest 5) algorithm. When the projector is using a LAN, a random 8 bytes will be returned if authentication is enabled. Bind this received 8 bytes and the authentication password and digest this data with the MD5 algorithm and add this in front of the commands to send. Following is a sample if the authentication password is set to password and the random 8 bytes are a572f60c. 1) Select the projector. 2) Receive the random 8 bytes a572f60c from the projector. 3) Bind the random 8 bytes a572f60c and the authentication password password and it becomes a572f60cpassword. 4) Digest this bind a572f60cpassword with MD5 algorithm. It will be e3d97429adffa11bce1f d4bde. 5) Add this e3d97429adffa11bce1f d4bde in front of the commands and send the data. Send e3d97429adffa11bce1f d4bde +command. 6) When the sending data is correct, the command will be performed and the reply data will be returned. Otherwise, an authentication error will be returned. NOTE As for the transmission of the second or subsequent commands, the authentication data can be omitted when the same connection. 12 3M All Rights Reserved.

13 RS-232C Communication / Network command table RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code Power Set TURN OFF BE EF A D TURN ON BE EF BA D Get BE EF D (Example Return) (Off) (On) (Cool Down) Input Source Set RGB1 BE EF FE D RGB2 BE EF E D HDMI BE EF E D MIU BE EF E D COMPONENT BE EF AE D S-VIDEO BE EF E D VIDEO BE EF E D Get BE EF CD D Error Status Get BE EF D9 D (Example Return) (Normal) (Cover error) (Fan error) (Lamp error) (Temp error) (Air flow error) (Lamp time error) (Cold error) (Filter error) BRIGHTNESS Get BE EF D Increment BE EF EF D Decrement BE EF E D BRIGHTNESS Reset Execute BE EF D CONTRAST Get BE EF FD D Increment BE EF B D Decrement BE EF A D CONTRAST Reset Execute BE EF A4 D PICTURE MODE Set NORMAL BE EF F BA CINEMA BE EF B3 F BA DYNAMIC BE EF E3 F BA BOARD (BLACK) BE EF E3 EF BA BOARD (GREEN) BE EF EE BA WHITE BOARD BE EF EE BA DAY TIME BE EF E3 C BA Get BE EF F BA (Example Return) (Normal) (CINEMA) (DYNAMIC) (CUSTOM) (BOARD(BLACK)) (BOARD(GREEN)) (WHITEBOARD) (DAY TIME) 3M All Rights Reserved. 13

14 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code GAMMA Set #1 DEFAULT BE EF E A #2 DEFAULT BE EF E A #3 DEFAULT BE EF E A #4 DEFAULT BE EF F7 E A #5 DEFAULT BE EF C7 EB A #6 DEFAULT BE EF EA A #1 CUSTOM BE EF FD A #2 CUSTOM BE EF FC A #3 CUSTOM BE EF FC A #4 CUSTOM BE EF F7 FD A #5 CUSTOM BE EF C7 FF A #6 CUSTOM BE EF FE A Get BE EF F4 F A User Gamma Pattern Set Off BE EF FB FA step Gray Scale BE EF B FB step Gray Scale BE EF B FB Ramp BE EF B FA Get BE EF C8 FA User Gamma Point 1 Get BE EF FE Increment BE EF E FE Decrement BE EF BF FF User Gamma Point 2 Get BE EF F4 FF Increment BE EF FF Decrement BE EF FE User Gamma Point 3 Get BE EF B0 FF Increment BE EF D6 FF Decrement BE EF FE User Gamma Point 4 Get BE EF C FE Increment BE EF A FE Decrement BE EF FB FF User Gamma Point 5 Get BE EF FF Increment BE EF E FF Decrement BE EF F FE User Gamma Point 6 Get BE EF C4 FE Increment BE EF A2 FE Decrement BE EF FF User Gamma Point 7 Get BE EF FE Increment BE EF E6 FE Decrement BE EF FF User Gamma Point 8 Get BE EF C FF Increment BE EF A FF Decrement BE EF CB FE M All Rights Reserved.

15 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code COLOR TEMP Set #1 HIGH BE EF B F B #2 MID BE EF B F B #3 LOW BE EF B F B #4 Hi-BRIGHT-1 BE EF B F B #5 Hi-BRIGHT-2 BE EF AB F B #6 Hi-BRIGHT-3 BE EF B F B0 30 0A 00 #1 CUSTOM (HIGH) BE EF CB F B #2 CUSTOM (MID) BE EF B F B #3 CUSTOM (LOW) BE EF AB F B #4 CUSTOM BE EF FB FF B (Hi-BRIGHT-1) #5 CUSTOM BE EF B FE B (Hi-BRIGHT-2) #6 CUSTOM BE EF B FE B0 30 1A 00 (Hi-BRIGHT-3) Get BE EF C8 F B COLOR TEMP GAIN R Get BE EF F B Increment BE EF F B Decrement BE EF F B COLOR TEMP GAIN G Get BE EF F B Increment BE EF F B Decrement BE EF C7 F B COLOR TEMP GAIN B Get BE EF C F B Increment BE EF EA F B Decrement BE EF B F B COLOR TEMP OFFSET R COLOR TEMP OFFSET G COLOR TEMP OFFSET B Get BE EF F B Increment BE EF F B Decrement BE EF B3 F B Get BE EF F B Increment BE EF F B Decrement BE EF F7 F B Get BE EF BC F B Increment BE EF DA F B Decrement BE EF B F B COLOR Get BE EF B Increment BE EF D Decrement BE EF COLOR Reset Execute BE EF D A TINT Get BE EF Increment BE EF F Decrement BE EF FE TINT Reset Execute BE EF C D B SHARPNESS Get BE EF F Increment BE EF Decrement BE EF SHARPNESS Reset Execute BE EF C4 D MY MEMORY Load Set 1 BE EF E D BE EF E D BE EF E D BE EF FE D M All Rights Reserved. 15

16 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code MY MEMORY Save Set 1 BE EF F2 D BE EF D BE EF D BE EF D PROGRESSIVE Set TURN OFF BE EF A TV BE EF DA FILM BE EF A Get BE EF D-YCS Set TURN OFF BE EF E A MOVIE BE EF A STILL IMAGE BE EF A Get BE EF D A VIDEO NR Set LOW BE EF MIDDLE BE EF D HIGH BE EF Get BE EF ASPECT Set NORMAL BE EF E DD :3 BE EF E D :9 BE EF E D :9 BE EF CE D SMALL BE EF FE D Get BE EF AD D OVER SCAN Get BE EF Increment BE EF F Decrement BE EF OVER SCAN Reset Execute BE EF EC D V POSITION Get BE EF D Increment BE EF B Decrement BE EF BA V POSITION Reset Execute BE EF E0 D H POSITION Get BE EF F Increment BE EF Decrement BE EF H POSITION Reset Execute BE EF C D H PHASE Get BE EF Increment BE EF F Decrement BE EF FE H SIZE Get BE EF B Increment BE EF D Decrement BE EF H SIZE Reset Execute BE EF D AUTO ADJUST Execute BE EF D A COLOR SPACE Set AUTO BE EF E RGB BE EF E SMPTE240 BE EF E REC709 BE EF FE REC601 BE EF CE Get BE EF D M All Rights Reserved.

17 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code COMPONENT Set COMPONENT BE EF A D SCART RGB BE EF DA D Get BE EF D C-VIDEO FORMAT Set AUTO BE EF A A 00 NTSC BE EF C PAL BE EF SECAM BE EF NTSC4.43 BE EF M-PAL BE EF C N-PAL BE EF Get BE EF S-VIDEO FORMAT Set AUTO BE EF E A 00 NTSC BE EF PAL BE EF SECAM BE EF NTSC4.43 BE EF M-PAL BE EF N-PAL BE EF Get BE EF HDMI Set AUTO BE EF D NORMAL BE EF D ENHANCED BE EF E6 D Get BE EF B5 D FRAME LOCK - RGB1 Set TURN OFF BE EF B C TURN ON BE EF AB C Get BE EF C FRAME LOCK - RGB2 Set TURN OFF BE EF B C TURN ON BE EF B C Get BE EF C FRAME LOCK - HDMI Set TURN OFF BE EF F C TURN ON BE EF EF C Get BE EF C C RGB IN1 Set SYNC ON G OFF BE EF E D AUTO BE EF CE D Get BE EF D D RGB IN2 Set SYNC ON G OFF BE EF A2 D AUTO BE EF D Get BE EF F1 D KEYSTONE V Get BE EF B9 D Increment BE EF DF D Decrement BE EF E D KEYSTONE V Reset Execute BE EF D C AUTO KEYSTONE V Execute BE EF E5 D D EXECUTE AUTO KEYSTONE V Set TURN OFF BE EF EA D F TURN ON BE EF A D F Get BE EF D9 D F KEYSTONE H Get BE EF E9 D B Increment BE EF F D B Decrement BE EF E D B KEYSTONE H Reset Execute BE EF D M All Rights Reserved. 17

18 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code ACTIVE IRIS Set TURN OFF BE EF B THEATER BE EF CB 2F PRESENTATION BE EF B 2E Get BE EF WHISPER Set NORMAL BE EF B WHISPER BE EF AB Get BE EF MIRROR Set NORMAL BE EF C7 D H:INVERT BE EF D V:INVERT BE EF A7 D H&V:INVERT BE EF D Get BE EF F4 D MONITOR OUT - RGB1 Set RGB1 BE EF E F B TURN OFF BE EF CE B B0 20 FF 00 Get BE EF D F B MONITOR OUT - RGB2 Set RGB2 BE EF CE F B TURN OFF BE EF FE B B4 20 FF 00 Get BE EF D F B MONITOR OUT - HDMI Set RGB1 BE EF A F B RGB2 BE EF BA F B TURN OFF BE EF A B B3 20 FF 00 Get BE EF F B MONITOR OUT - MIU Set RGB1 BE EF B6 F B RGB2 BE EF F B TURN OFF BE EF B B6 20 FF 00 Get BE EF F B MONITOR OUT - COMPONENT MONITOR OUT - S-VIDEO MONITOR OUT - VIDEO MONITOR OUT - STANDBY Set RGB1 BE EF F2 F B RGB2 BE EF F B TURN OFF BE EF B B5 20 FF 00 Get BE EF C1 F B Set RGB1 BE EF F B RGB2 BE EF F B TURN OFF BE EF B B2 20 FF 00 Get BE EF B5 F B Set RGB1 BE EF C2 F B RGB2 BE EF F B TURN OFF BE EF B B1 20 FF 00 Get BE EF F1 F B Set RGB1 BE EF A F BF RGB2 BE EF EA F BF TURN OFF BE EF DA B BF 20 FF 00 Get BE EF F BF VOLUME - RGB1 Get BE EF CD CC Increment BE EF AB CC Decrement BE EF A CD VOLUME - RGB2 Get BE EF FD CD Increment BE EF B CD Decrement BE EF A CC M All Rights Reserved.

19 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code VOLUME - HDMI Get BE EF CC Increment BE EF EF CC Decrement BE EF E CD VOLUME - MIU Get BE EF CC Increment BE EF CC Decrement BE EF F2 CD VOLUME - COMPONENT 3M All Rights Reserved. Get BE EF CC Increment BE EF CC Decrement BE EF B6 CD VOLUME - S-VIDEO Get BE EF CD Increment BE EF CD Decrement BE EF C2 CC VOLUME - VIDEO Get BE EF CD Increment BE EF CD Decrement BE EF CC VOLUME - AUDIO OUT STANDBY Get BE EF D9 CF F Increment BE EF BF CF F Decrement BE EF E CE F TREBLE - RGB1 Get BE EF D C Increment BE EF B C Decrement BE EF BA C TREBLE -RGB2 Get BE EF D C Increment BE EF B C Decrement BE EF A C TREBLE - HDMI Get BE EF C Increment BE EF F C Decrement BE EF FE C TREBLE - MIU Get BE EF C Increment BE EF E3 C Decrement BE EF C TREBLE - COMPONENT Get BE EF C1 C Increment BE EF A7 C Decrement BE EF C TREBLE - S-VIDEO Get BE EF B5 C Increment BE EF D3 C Decrement BE EF C TREBLE - VIDEO Get BE EF F1 C Increment BE EF C Decrement BE EF C TREBLE - AUDIO OUT STANDBY Get BE EF CB F Increment BE EF F CB F Decrement BE EF AE CA F BASS - RGB1 Get BE EF D FB Increment BE EF B FB Decrement BE EF BA FA BASS - RGB2 Get BE EF D FA Increment BE EF B FA Decrement BE EF A FB BASS - HDMI Get BE EF FB Increment BE EF F FB Decrement BE EF FE FA

20 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code BASS - MIU Get BE EF FB Increment BE EF E3 FB Decrement BE EF FA BASS - COMPONENT Get BE EF C1 FB Increment BE EF A7 FB Decrement BE EF FA BASS - S-VIDEO Get BE EF B5 FA Increment BE EF D3 FA Decrement BE EF FB BASS - VIDEO Get BE EF F1 FA Increment BE EF FA Decrement BE EF FB BASS - AUDIO OUT STANDBY Get BE EF F F Increment BE EF F F F Decrement BE EF AE F F SRS WOW - RGB1 Set TURN OFF BE EF FE FF MID BE EF E FE HIGH BE EF E FF Get BE EF CD FF SRS WOW - RGB2 Set TURN OFF BE EF CE FE MID BE EF AE FF HIGH BE EF E FE Get BE EF FD FE SRS WOW - HDMI Set TURN OFF BE EF BA FF MID BE EF DA FE HIGH BE EF A FF Get BE EF FF SRS WOW - MIU Set TURN OFF BE EF FF MID BE EF FE SRS WOW - COMPONENT HIGH BE EF FF Get BE EF FF Set TURN OFF BE EF FF MID BE EF FE HIGH BE EF C2 FF Get BE EF FF SRS WOW - S-VIDEO Set TURN OFF BE EF FE MID BE EF FF HIGH BE EF B6 FE Get BE EF FE SRS WOW - VIDEO Set TURN OFF BE EF FE MID BE EF FF HIGH BE EF F2 FE Get BE EF FE SRS WOW - AUDIO Set TURN OFF BE EF EA FC F OUT STANDBY MID BE EF A FD F HIGH BE EF A FC F Get BE EF D9 FC F MUTE Set TURN OFF BE EF D TURN ON BE EF D6 D Get BE EF D SPEAKER Set TURN OFF BE EF E D C TURN ON BE EF FE D C Get BE EF D D C M All Rights Reserved.

21 Names Operation Type Header RS-232C Communication / Network command table Command Data CRC Action Type Setting Code AUDIO - RGB1 Set TURN OFF BE EF FE DD AUDIO1 BE EF E DC AUDIO2 BE EF E DC AUDIO3 BE EF E DD AUDIO4 BE EF E DF Get BE EF CD DD AUDIO - RGB2 Set TURN OFF BE EF CE DC AUDIO1 BE EF E DD AUDIO2 BE EF AE DD AUDIO3 BE EF E DC AUDIO4 BE EF E DE Get BE EF FD DC AUDIO - HDMI Set TURN OFF BE EF BA DD AUDIO1 BE EF A DC AUDIO2 BE EF DA DC AUDIO3 BE EF A DD AUDIO4 BE EF A DF AUDIO_HDMI BE EF A C Get BE EF DD AUDIO - MIU Set TURN OFF BE EF DD AUDIO1 BE EF E6 DC AUDIO2 BE EF DC AUDIO3 BE EF DD AUDIO4 BE EF B6 DF MIU BE EF B6 D Get BE EF DD AUDIO - COMPONENT Set TURN OFF BE EF DD AUDIO1 BE EF A2 DC AUDIO2 BE EF DC AUDIO3 BE EF C2 DD AUDIO4 BE EF F2 DF Get BE EF DD AUDIO - S-VIDEO Set TURN OFF BE EF DC AUDIO1 BE EF D6 DD AUDIO2 BE EF DD AUDIO3 BE EF B6 DC AUDIO4 BE EF DE Get BE EF DC AUDIO - VIDEO Set TURN OFF BE EF DC AUDIO1 BE EF DD AUDIO2 BE EF DD AUDIO3 BE EF F2 DC AUDIO4 BE EF C2 DE Get BE EF DC AUDIO OUT STANDBY Set TURN OFF BE EF EA DE F AUDIO1 BE EF A DF F AUDIO2 BE EF A DF F AUDIO3 BE EF A DE F AUDIO4 BE EF A DC F Get BE EF D9 DE F M All Rights Reserved. 21

22 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code HDMI AUDIO Set 1 BE EF AE C BE EF E C Get BE EF D C REMOTE FRONT Set Off BE EF FF On BE EF F Get BE EF CC REMOTE REAR Set Off BE EF On BE EF Get BE EF REMOTE TOP Set Off BE EF On BE EF D Get BE EF REMOTE FREQUENCY NORMAL REMOTE FREQUENCY HIGH Set Disable BE EF FF 3D Enable BE EF F 3C Get BE EF CC 3D Set Disable BE EF C Enable BE EF D Get BE EF C LANGUAGE Set ENGLISH BE EF F7 D FRANCAIS BE EF D DEUTSCH BE EF D ESPANOL BE EF D ITALIANO BE EF D NORSK BE EF A7 D NEDERLANDS BE EF D PORTUGUESE BE EF C7 D 日本語 BE EF D BE EF A7 D BE EF DE BE EF D A 00 SVENSKA BE EF C7 D B 00 PYCCKNN BE EF F7 D C 00 SUOMI BE EF D D 00 POLSKI BE EF D E 00 TÜRKÇE BE EF D F 00 Get BE EF C4 D MENU POSITION V Get BE EF D Increment BE EF D Decrement BE EF F7 D MENU POSITION V Execute BE EF A8 C Reset MENU POSITION H Get BE EF D Increment BE EF D Decrement BE EF B3 D MENU POSITION H Reset Execute BE EF DC C M All Rights Reserved.

23 Names Operation Type Header RS-232C Communication / Network command table Command Data CRC Action Type Setting Code BLANK Set MyScreen BE EF FB CA ORIGINAL BE EF FB E BLUE BE EF CB D WHITE BE EF B D BLACK BE EF B D Get BE EF D BLANK On/Off Set TURN OFF BE EF FB D TURN ON BE EF B D Get BE EF C8 D START UP Set MyScreen BE EF CB CB ORIGINAL BE EF B D TURN OFF BE EF B D Get BE EF D MyScreen LOCK Set TURN OFF BE EF B EF C TURN ON BE EF AB EE C Get BE EF EF C MESSAGE Set TURN OFF BE EF F D TURN ON BE EF F D Get BE EF BC D TEMPLATE Set TEST PATTERN BE EF D DOT-LINE1 BE EF D3 D DOT-LINE2 BE EF D DOT-LINE3 BE EF B3 D DOT-LINE4 BE EF DB Get BE EF D TEMPLATE On/Off Set TURN OFF BE EF BF D TURN ON BE EF F D Get BE EF C D AUTO SEARCH Set TURN OFF BE EF B6 D TURN ON BE EF D Get BE EF D AUTO OFF Get BE EF Increment BE EF E Decrement BE EF BF AUTO ON Set TURN OFF BE EF B TURN ON BE EF AB Get BE EF LAMP TIME Get BE EF C2 FF LAMP TIME Reset Execute BE EF DC FILTER TIME Get BE EF C2 F A FILTER TIME Reset Execute BE EF C M All Rights Reserved. 23

24 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code MY BUTTON-1 Set RGB1 BE EF A RGB2 BE EF FA HDMI BE EF CA MIU BE EF A COMPONENT BE EF A S-VIDEO BE EF A VIDEO BE EF AA INFORMATION BE EF FA 3E AUTO KEYSTONE BE EF A 3F EXECUTE MY MEMORY BE EF A 3F PICTURE MODE BE EF A 3E FILTER RESET BE EF A 3C ACTIVE IRIS BE EF AA 3D MY IMAGE BE EF A 3D AV MUTE BE EF AA TEMPLATE BE EF CA B 00 LIVE MODE BE EF FA 2A THUMBNAIL BE EF A 2B SLIDE SHOW BE EF A 2B DIRECTORY BE EF A 2A REMOVE MEDIA BE EF A Get BE EF MY BUTTON-2 Set RGB1 BE EF C RGB2 BE EF HDMI BE EF MIU BE EF COMPONENT BE EF S-VIDEO BE EF A VIDEO BE EF INFORMATION BE EF F AUTO KEYSTONE BE EF E EXECUTE MY MEMORY BE EF E PICTURE MODE BE EF F6 3F FILTER RESET BE EF C6 3D ACTIVE IRIS BE EF C MY IMAGE BE EF A6 3C AV MUTE BE EF TEMPLATE BE EF B 00 LIVE MODE BE EF B THUMBNAIL BE EF A SLIDE SHOW BE EF A DIRECTORY BE EF F6 2B REMOVE MEDIA BE EF C Get BE EF F M All Rights Reserved.

25 RS-232C Communication / Network command table Names Operation Type Header Command Data CRC Action Type Setting Code MY SOURCE Set RGB1 BE EF FA RGB2 BE EF A 3A HDMI BE EF A MIU BE EF A 3B COMPONENT BE EF AA 3B S-VIDEO BE EF A VIDEO BE EF A Get BE EF C MAGNIFY Get BE EF C D Increment BE EF A D Decrement BE EF CB D FREEZE Set NORMAL BE EF D FREEZE BE EF D Get BE EF B0 D CLOSED CAPTION DISPLAY CLOSED CAPTION MODE CLOSED CAPTION CHANNEL Set TURN OFF BE EF FA TURN ON BE EF A AUTO BE EF A Get BE EF C Set CAPTIONS BE EF TEXT BE EF Get BE EF Set 1 BE EF D BE EF BE EF B BE EF Get BE EF MY IMAGE Set OFF BE EF A C IMAGE-1 BE EF AA C IMAGE-2 BE EF A C IMAGE-3 BE EF CA C IMAGE-4 BE EF FA C Get BE EF C MY IMAGE Execute BE EF C IMAGE-1 Delete MY IMAGE Execute BE EF C IMAGE-2 Delete MY IMAGE Execute BE EF C9 C IMAGE-3 Delete MY IMAGE IMAGE-4 Delete Execute BE EF BD C M All Rights Reserved. 25