B650 Classroom Instructions Call 2490 for additional assistance.

Transcription

1 B650 Classroom Instructions Call 2490 for additional assistance. Updated: November 17 th, 2010

2 LCD Data Projector Press and hold the black button at the top of the Mitsubishi remote marked ON for about 5 seconds. A green light should appear on the projector. If it does not, move closer and try again. Wait approximately 30 seconds for the picture to appear. For Laptop computer input, press the black button on the remote marked Computer 1. For Desktop computer input, press the black button on the remote marked Computer 2. For DVD/VCR input, press the black button on the remote marked Video. To turn off the projector press the standby button at the top of the Mitsubishi remote and press it again to confirm the shutdown. It is normal for the projector to remain running for several seconds while it cools. Mitsubishi Remote

3 Desktop Computer Press the black power button located at the center of the computer system unit (located in the desk cabinet). You should see a green light appear. If you do not see an image on the LCD screen, use the switch located on the bottom right edge of the screen. You should see another green light on the monitor if the power is on. If you wish to use the LCD Data Projector, turn it on now. (See separate instructions for Data Projector) If you wish to use the Classroom Sound System, turn the amplifier on now. (See separate instructions for Sound System) Wait approximately 30 seconds for the computer to boot. You should see a login screen when it is complete. Enter your login username (usually firstname.lastname ) and your password (initially your ID number). Ensure that the Domain is set to uleth If you do not have a login username for the University network, contact the Information Technology department at When you are finished, select Logoff from the start menu.

4 Laptop Computer Locate the laptop connection cables on the side of the desk cabinet. Carefully connect the cables to the back of your laptop. If you wish to use the LCD Data Projector, turn it on now. (See separate instructions for Data Projector) If you wish to use the Classroom Sound System, turn the amplifier on now. (See separate instructions for Sound System) Once the data projector is turned on and set to the correct input, turn on your laptop computer and the image should appear. Most laptops will enable their video output when they are connected in the correct order. Remember to connect the cables and turn on the projector before you turn on your laptop. NOTE: If you have turned on the LCD Data Projector and your laptop and the projector display is not working, you may have to ACTIVATE your laptop s CRT output. You should consult your laptop manual for this procedure. Most laptops have an FN key located somewhere near the bottom left of the keyboard. You should also see a Laptop docking connectors If you are not sure what key to press for the video output, here are some common laptop manufacturers and the appropriate keystrokes: Your laptop should be set to a 1024x768 resolution for optimal performance. function key either marked LCD/CRT or displaying a small screen icon. Pressing these buttons at the same time will toggle the CRT output on and off. If you have difficulty with this procedure, please contact the Information Technology help desk. Dell IBM or Sony Toshiba or HP Compaq Hold Fn and press the appropriate function key. FN+F8 FN+F7 FN+F5 FN+F4

5 VCR / DVD Player Turn on the player using the power switch on the front of the unit or the power button on the remote commander. Carefully insert the cassette or DVD you wish to play. If it does not load easily into the player, contact classroom support. If you experience problems: If you can t hear any audio, check to ensure that the amplifier is turned on, and the VCR / DVD source volume is turned up. Also try depressing the Audio button on the remote commander. If you can t see any video, check to ensure that the LCD Data projector is set to VIDEO input or try depressing the VCR/TV button on the remote commander. If the remote commander is not functioning, the batteries may need to be replaced. Most functions are available from the front panel of the unit. Call classroom support for additional batteries if needed. One of the following remotes should be available to control the DVD/VCR Player. Panasonic Panasonic Toshiba Toshiba LG LG

6 Classroom Sound System There are two types of amplifiers in the classroom. Please use the corresponding one in the classroom: Press the POWER button on the black amplifier located in the desk cabinet. The button and front display panel will illuminate. Press the numbered input button for the source you want to hear. The source channels are labeled as follows: 1. Wireless Microphone 2. Desktop Computer 3. Laptop Computer 4. DVD / VCR unit Adjust the channel volume slowly until you reach a good listening level. The channel volume can be set independently for each input. If you do not hear sound from the selected input, press the left on/off button once. This will toggle muting of the currently selected channel. When you are finished, turn down the channel volume and press the power button to shut off. Or Press the POWER button on the black amplifier located in the desk cabinet. Set the Master volume to a moderate level. Locate the gain for the specific device you will be using (ie. microphone). Turn the gain up slowly until appropriate volume is reached.

7 Wireless Microphone Turn on the TOA amplifier and set the volume to a moderate level. If the microphone receiver box (pictured) is not turned on, press the power button on the right side of the unit until the screen turns on. Depending on the model of microphone, please see corresponding microphone below: Hold the power button on the top edge of the transmitter unit until a green light appears. Speak at a normal level and adjust the volume as necessary. To mute the microphone, press the power button momentarily - the green light will turn amber, indicating that the mute is enabled. To disable muting, press the power button again briefly. Do not press the select button on the front of the transmitter. This may change the frequency of the microphone and render it inoperable. When you are done using the microphone, hold the power button until all lights turn off. Locate two switches on the wireless microphone transmitter. o Switch the main power switch to the ON position. o Switch the mute switch to the ON position. Speak at a normal level and adjust the volume as necessary. Please remember to turn off the wireless microphone to conserve battery power for other users.