Smarther X8000-X8000W

Transcription

1 X8000-X8000W

2

3 Contents Your Smarther, use it now! 4 Heat your home immediately (Boost) 4 Set the temperature 5 Manage several houses and several Smarther 6 General information 7 Symbols on the display 7 Operation 8 Basic functions 0 Boost functions 0 Set the temperature Room humidity display 5 Reset 6 Advanced functions (Thermostat App) 7 Introduction 7 Download the Thermostat App 8 Account registration 9 Authentication Forgotten password 3 Account deletion 5 Association to the Smarther 6 Connection of the Smarther to the home Wi-Fi network 7 Account management 3 Account information 3 Change password 33 Delete the account 33 Home Page 34 Set the temperature 35 Set the Boost function 36 Switch the Smarther off 37 Programming 38 Create a program using the guided procedure 40 Create a program using the manual procedure 45 Copy a program 5 Modify a program 53 Modify the profile 54 Copy a profile 55 Activate a program 56 Users 57 Settings 59 Help 63 3

4 Your Smarther, use it now! Heat your home immediately (Boost) You can switch your system on quickly with the BOOST function ACTIVATION FROM DEVICE or FROM APP. Touch to activate the function Quick guide. Select the switching-on period from 30/60/90 minutes A visual indicator will show you the remaining time for which your system will remain on 4

5 Set the temperature ACTIVATION FROM DEVICE or FROM APP. From the Smarther scroll to display the temperature setting page or, from the App, touch the icon 3 Quick guide 4. From the Smarther touch the keys to increase or decrease the temperature, or from the App scroll to set the temperature and the day( 3 ) and time ( 4 ) until which it is to be maintained. Select always"to maintain it for an undefined time. Note: when you want to set different temperatures depending on the time and day of the week, you need to create a special program (see programming) 5

6 Manage several houses and several Smarther With the Thermostat App, it is possible to manage up to 4 houses and up to 4 Smarther for each house 3 Touch to open the pull-down menu Touch to open the house selection menu 3 Scroll to select the house to manage Quick guide Touch to select the thermostat among those found 5 Touch to cancel the existing programming 6 Touch to set the temperature 6

7 General information Note: the,,, icons, are only on when the device is on.if the device is in stand by the icons will be off. Touch screen display 4. Wi-Fi connection key. Temperature/humidity display 3. Boost mode indicator Symbols on the display 5. Reset Key Icon Smarther "OFF" Heating mode operation Meaning The Smarther is set with a default temperature of 7 C winter/35 C summer. You can set this condition from the App using the Switch Smarther Off function or manually, increasing or decreasing the temperature to the default values. The system is in heating mode and is ON. Cooling mode operation The system is in cooling mode and is ON. Manual mode operation Boost mode activation Keys for temperature setting Wi-Fi connection indicator The manual mode temporarily excludes the hour programmings; using the Thermostat App you can also set the length of this mode. When this time has elapsed operation will start again as in the programming The Boost forces the switching on of the system for a limited time (30, 60 or 90 minutes) independent of the measured and programmed temperature The set value is only valid for the manual mode operation. ON = connected OFF = disconnected *Note: if there is App programming, all the functions set manually last until the first variation caused by the profile programmed with the App, excluding the Boost function which continues. 7

8 Operation In basic mode the Smarther allows you to adjust the temperature manually and switch the system on for a limited time (Boost mode). The advanced functions are available through the Thermostat App, which can be downloaded free from the Stores (for ios devices from App Store, for Android devices from Play Store). In advanced mode you can program all the functions: time bands, weekly programming etc. The smartphone on which the Thermostat App is installed and the Smarther communicate via the device's Wi-Fi connection. You therefore do not need wire connections or a mains power supply and connections with the heating system Functions available and differences between newly installed Smarther and Smarther connected with App Functions Smarther just installed (not connected) By Smarther Smarther connected with the App By App Boost At the end of the set period the Smarther returns to the mode which was active before the activation. At the end of the set period the Smarther returns to the programming in progress. At the end of the set period the Smarther returns to the programming in progress. Switching off (Antifreeze/Thermal protection) The set mode is permanent The set mode lasts until the first variation caused by the profile programmed with the App The set mode can be maintained to a set date and time I set the temperature The set temperature is permanent The set temperature lasts until the first variation caused by the profile programmed with the App The set temperature can be maintained to a set date and time Display the humidity Displayed in the third page Displayed in the third page Displayed in the Home Page 8

9 Functions available and differences between newly installed Smarther and Smarther connected with App Functions Smarther just installed (not connected) By Smarther Smarther connected with the App By App Settings Programming of a daily or weekly temperature profile Weather Firmware update Management of several Smarther and several houses Note: a domestic Wi-Fi with internet access is needed for the connection between the Smarther X8000/W and the smartphone. To use the service, the Customer must acquire the technical equipment which allows access to the Internet, on the basis of an agreement made by the Customer himself with an ISP (Internet Service Provider). BTicino plays no part in this. Install the dedicated Thermostat application on your smartphone to program and use the Smarther. The services offered by means of the App require being able to interact with Smarther remotely and through the Internet. In these cases the integration and good working between Smarther and App may depend on: a) quality of the Wi-Fi signal; b) quality of the data signal; We would like to inform you that the remote use via the App involves the use of data. The cost linked to data usage depends on the type of contract which the customer has with his ISP (Internet Service Provider) and is solely the customer s responsibility. 9

10 Basic functions Boost functions The Boost forces the switching on of the system for a limited time (30, 60 or 90 minutes) independent of the measured and programmed temperature. Once the time set has elapsed, Smarther will resume operation according to the previous programming.. Touch the display, the symbol comes on. Touch the symbol once or more to set the function duration; the display shows the set time, at the same time the LED lights up. After setting the desired duration (30, 60 or 90 minutes) wait until the digits stop flashing after which the Boost mode will be activated. 0

11 The display shows the measured temperature; the LED gradually switches off while the set time passes by To end the setting early touch the symbol; Smarther will continue operation according to the previous programming.

12 Set the temperature The temperature level that can be locally set refers only to the manual mode operation.. Touch the display. Scroll on the display to go to the next page 3 3. The actual setting is displayed, modify the setting with the keys

13 Once the setting is complete wait for a few seconds. The display will show the measured temperature. 3

14 Note: on setting the minimum (7 C antifrost, for heating) or maximum (35 C thermal protection, for cooling) the switching-off symbol appears on the display. 4

15 Room humidity display Smarther contains a sensor that detects the humidity percentage in the room; follow the procedure described below to display the measured value.. Touch the display. Scroll twice on the display to go to the dedicated page The measured humidity percentage is visible for a few seconds, then the measured temperature display will appear again. 5

16 Reset This operation restores the Smarther factory settings and all programmings and associations will be deleted. Keep the reset pushbutton on the side of the Smarther pressed. A countdown will start (about 0 seconds) at the end of which you will hear a confirmation beep. 6

17 Advanced functions (Thermostat App) Introduction You can program the Smarther with the free Thermostat App. To do this you must:. Download the App from the Stores. Register and create an account 3. Associate the account to your Smarther via the App + 3 7

18 At this point from the App you can: Set the temperature Use the Boost functiont Set the switching off Set the temperature using DAILY or WEEKLY programming Manage users, Smarther and houses You can also display the measured humidity and the weather on the App Home Page Note:the weather service is based on the web forecast supplied by the online weather service ( Download the Thermostat App To use the Thermostat functions, first of all download it from the Stores (for ios devices from App Store, for Android devices from Play Store). On your Smartphone run the App to read the QR codes and then frame the QR Code Note: you can find the same QR code in the Instruction Sheet supplied with the Smarther 8

19 Account registration You must first register to be able to use the Thermostat App and thus use the Smarther advanced functions. After opening the App follow the registration instructions: when the account has been created it will be common to all the connected Legrand/BTicino device App. If you have already registered, use your credentials Touch to register and create an account. Enter your data 3. Touch to confirm 4. Tick to accept the terms and conditions of use laid down in the associated text (obligatory) 5. Touch to continue. 9

20 6 6. Touch to end the procedure After confirming, the system will send the data (temporary password) to the address indicated by you in the registration phase for the first access Enter the 8. Enter the temporary password sent to you via 9. Touch to make the login 0

21 For safety reasons you will be asked to change the temporary password for a customised one For security reasons enter a new password with these features: minimum length 8 characters; must contain at least one letter and one number; it must be different from the last 5 passwords used. 8. Enter the password again 9. Touch to confirm. If the modification has been successful you will receive a confirmation At this point the system will show you a tutorial to help you associate your Smarther to the Thermostat App Note: if your Smarther is already associated and you want to add another user who can also use the same functions, you must invite him using the appropriate procedure directly from your smartphone. You can use the same account on several smartphones simultaneously.

22 Authentication After registering with the portal, you can authenticate by entering and password. E D A B C A. Touch to start the password recovery procedure B. Touch to create a new account C. Touch to start the account deletion procedure. Account deletion cannot be reversed and is common to all the connected Legrand/BTicino device App D. Tick the box to access subsequently without having to repeat the authentication E. Touch to make the password visible. Enter and password. Touch to access Note: after three failed access attempts (wrong password) in an hour, the system blocks the account for 5 minutes.

23 Forgotten password When you have forgotten the password:. Touch to activate the password recovery procedure 3. Enter the address linked to your account to which the new password will be sent 3. Touch to zero the password and quit the procedure Now your account password has been reset and a new password which you can use to access the Thermostat App has been sent to the address entered in point. 3

24 Enter the 5. Enter the temporary password sent to you via 6. Touch to make the login Enter the new password For security reasons enter a new password with these features: minimum length 8 characters; must contain at least one letter and one number; it must be different from the last 5 passwords used. 8. Enter the password again 9. Touch to confirm. If the procedure has been successful you will receive a confirmation 4

25 Account deletion You can delete an account using the procedure. Touch to start the procedure 3. Enter address and password of the account to delete 3. Touch to confirm 4 4. Touch to proceed. Remember that when the procedure is complete your account will be definitively cancelled Note: the account is common to all the Apps of the Legrand/BTicino connected devices. If it is modified or deleted you will no longer have access to all the connected devices 5

26 Association to the Smarther After registering and authenticating for the first time (the first smartphone) you will be shown a tutorial. Follow this to associate your account to the Smarther. This operation is only necessary on the first access and allows you to activate the connection between the two devices. You can also invite other users so that they can use the connected Smarther functions. Perform the following steps to make the association: My home Wi-Fi 0 Wi-Fi 0 Wi-Fi 03 3 Wi-Fi 04 Wi-Fi 05 Wi-Fi 06 Wi-Fi 07. First of all connect the smartphone to the home Wi-Fi network. Authenticate after registering 3. If the smartphone has not yet been associated to the Smarther this screen appears. Touch to start the association procedure Caution: if the association procedure is interrupted before it is completed, before repeating it you must reset the Smarther following the procedure 6

27 The first operation to be carried out to make the association is to connect the Smarther to the home Wi-Fi network Connection of the Smarther to the home Wi-Fi network A A. Enable/disable the system geolocation.if disabled, the weather functions will no longer be available.. Enter a description for the system. Touch to continue. The following screen appears 3 3. Keep the upper Smarther pushbutton pressed until AP appears 7

28 4 4. Press to continue 5 5. Go to your mobile phone's Wi-Fi network settings. Wi-Fi Thermostat 5C-C3-EB Wi-Fi 0 Wi-Fi 0 Wi-Fi 0 Wi-Fi 03 Wi-Fi 04 6 Wi-Fi 0 Wi-Fi 03 7 Wi-Fi 05 Wi-Fi 04 Wi-Fi 06 Wi-Fi 05 Wi-Fi 07 Wi-Fi 06 Wi-Fi Thermostat 5C-C3-EB Wi-Fi Seleziona la rete temporanea che crea lo Smarther per collegarsi allo smartphone (Wi-Fi Select the temporary network which the Smarther creates to connect to the smartphone (Wi-Fi Thermostat 5C-C3-EB"). You may need to wait for to minutes before the Smarther Wi-Fi network appears in the list. Note: to return to the App use the Smartphone Back key (Android) or Home key (ios). 7. Touch to continue. Note: after 5 minutes the network is no longer available, repeat the operation from point 3. 8

29 9 8 My home My home Network 0 Network 0 Network Now select the home Wi-Fi network to which the Smarther will be connected 9. Enter and confirm the home Wi-Fi network password 0. Touch to continue.. The Smarther search now starts. It may take a few minutes.. When the Smarther cannot automatically associate to the smartphone this screen appears. Enter the Smarther IP address. If I do not know it: 3 3. Press the Wi-Fi pushbutton 9

30 The numbers which make up the IP address appear in sequence after IP Enter the Smarther IP address 5. Touch to continue. 30

31 The following screen appears when the association has completed Enter a name for the Smarther (the App creates one automatically) 7. Touch to continue, the Home Page appears *Note: to continue a name must be entered. 8. On the first access the Smarther is in off mode (set with a default temperature 7 C winter/35 C summer) Touch to delete the existing programming 9. Touch to set the temperature Caution: to delete the association of a Smarther from the App, you must: - make sure that it is connected to the internet via Wi-Fi; - perform the reset procedure; 3 - exit the App and repeat the authentication 3

32 Account management After you have authenticated and associated to the Smarther, you can manage your account in the section in the pulldown menu A B C. Touch to open the pull-down menu. Touch to enter the account management section A. Displays and modifies your account's information B. Change password C. Delete the account Note: the access credentials are common to all the BTicino connected devices, thus if these data are modified or deleted access to all the connected devices will be prevented. Account information In this section you can modify the name, surname, address and other data of your account Touch to modify the data. Touch to continue 3. Tick to accept the terms and conditions of use laid down in the associated text (obligatory) 4. Touch to confirm 5. Touch to return to the previous page 3

33 Change password In this section you can change your account password 3 4. Enter the old password. For security reasons enter a new password with these features: minimum length 8 characters; must contain at least one letter and one number; it must be different from the last 5 passwords used. 3. Enter the password again 4. Touch to confirm. If the modification has been successful you will receive a confirmation Note: the access credentials are common to all the BTicino connected devices, thus if these data are modified or deleted access to all the connected devices will be prevented. Delete the account In this section delete your account definitively 3. Enter address and password of the account to delete. Touch to confirm 3. Touch to proceed. Remember that when the procedure is complete your account will be definitively cancelled Note: the access credentials are common to all the BTicino connected devices, thus if these data are modified or deleted access to all the connected devices will be prevented. 33

34 Home Page After being authenticated, from this page you can interact with your Smarther to manage the home temperature. You can also program the temperature and other functions via the pulldown menu System Name. Weather forecast 3. Name of the Associated Smarther 4. Measured temperature 5. Measured humidity percentage 6. Temperature zone set 7. Set the Switching off function 8. Set the Boost function 9. Set the Temperature 0. Heating or cooling contact switched 9. Outside temperature supplied by the weather service (if you have enabled geolocation). Pull-down menu: HOME: close the menu and return to the Home Page. PROGRAMS: open the section where you can set daily or weekly temperature programs via guided or customised configuration. USERS: open the section where you can display those users which can interact with your system and if necessary invite new ones or delete existing ones. SETTINGS: in this section you can add new Smarther and new homes (systems), you can also update the Smarther firmware. Account: open the section where you can display information, change password and delete the account. Help: opens the assistance contact pages where you can send notification of a problem. Information on...: displays the Smarther firmware version and the App version. EXIT: exit the account

35 Set the temperature This function allows you to set a temperature without time limits or up to a certain date and time. A visual and text indication will indicate the remaining time. You can also modify the setting before the end via the function. 3 4 A B C D E Touch to set the function; select always to maintain it for an indefinite time, or. Scroll to set the temperature 3. Scroll to set the date to which it will be maintained 4. Scroll to set the time to which it will be maintained 5. Touch to confirm The temperature is now set A. Set mode indication B. Set temperature C. End setting date and time D. Time indication bar: indicates the elapsed time (dark grey) and the remaining time (light grey) E. Remaining time 6. Touch to modify, before the end, the date and time at which the setting ends 7. Touch to quit the current mode and return to the programmed mode 35

36 Set the Boost function This function forces the switching on of the system (both heating and cooling) for a limited time (30, 60 or 90 minutes) independent of the measured or programmed temperature. Once the time set has elapsed, the Smarther will resume operation according to the previous programming. 3 A B 4. Touch to set the function. Touch to set the time for which the system will remain on A. Graphic indication of the time selected B. Text indication of the time selected 3. Touch several times until the time desired, 30, 60 or 90 minutes, is reached 4. Touch to confirm The function is now set A 5 B C D A. Set mode indication 6 B. End setting date and time C. Time indication bar: indicates the elapsed time (grey) and the remaining time (red/light blue) D. Remaining time 5. Touch to modify the previously set time before the end 6. Touch to quit the current mode and return to the programmed mode 36

37 Switch the Smarther off This function allows you to set switching off the Smarter, putting the system in antifrost/thermal protection mode. The switching off can be programmed up to a certain date/time or without time limits. This status will remain active up to the date and time set Touch to set the function. Scroll to set to which day the Smarther will remain off (select always to switch it off for an undefined time) 3. Scroll to set to which time the Smarther will remain off 4. Touch to confirm The Smarther is off until the date and time set 5 A B C D A. Set mode indication 6 B. End setting date and time C. Time indication bar: indicates the elapsed time (dark grey) and the remaining time (light grey) D. Remaining time 5. Touch to modify, before the end, the date and time at which the setting ends 6. Touch to quit the current mode and return to the programmed mode 37

38 Programming Via this function you can set a different temperature depending on the time and day of the week. After the first association to the device, on entering the Programs section, you will find a predefined program which sets a temperature of 7 C winter/35 C summer for the whole 4 hours. 3. Touch to open the pull-down menu. Touch to open the program section A predefined program is present as default. This program cannot be modified but will be replaced by the first program you create. 3. Touch to create a customised program which will replace the previous program A B G C F D E A Active program indication B Program Name C Create the program D Delete the program Note: if you delete all the programs, the predefined program will reappear E Graphic indication of time intervals and temperature levels of set program F Modify the program G Displays/modifies preset temperature levels 38

39 You can create a program in different ways: Guided procedure From your answers to simple questions about your habits, this method helps you to simply and intuitively create a program suitable for your needs using preset temperature levels. Manual procedure This method allows you, starting from scratch, to create a customised program defining the temperature levels and the time intervals. Program copy You can also create a new program by copying an existing one and if necessary modifying it. The modes of creating programs are the same for both daily and weekly programs. In the first case the program is repeated for all the days of the week, while in the second case you can define different temperature levels and time intervals for every day of the week Daily program Weekly program 39

40 Create a program using the guided procedure 3 4 Touch to create a new program Touch to use the guided procedure 3 Touch to select whether the program will be the same for all the days of the week (daily) or different depending on the days (weekly) 4 Touch to continue Scroll to set the times which delimit the time intervals 6 Touch to continue 7 Touch to define the days of the week when you are mainly at home (weekly program only) 8 Touch to continue 40

41 A B 9 9 Scroll to modify the temperature levels if necessary A = modalità riscaldamento B= modalità raffrescamento This method uses predefined temperature levels with names and colours which show possible use: OUT Temperature to set when you are not at home AT HOME Temperature to set when you are at home NIGHT Temperature to set at night You can modify preset temperature levels, also by touching the screen n icon in the initial program Note: you are only asked to set the temperature levels when the first program is entered 4

42 B A C Touch to continue Enter a name for the program If necessary touch modify the program 3 Touch to send the program to the device After a few seconds a confirmation message will indicate that the procedure has been successful. A Now the program appears in the program list and can be activated,modified or deleted B Active program C Not active program 4

43 The system has automatically created this program via this configuration and on the basis of your answers: During the week (from Monday to Friday) 4:00-08:00 zz z 08:00-09:00 09:00-9:30 9:30-3:30 3:30-4:00 zz z 43

44 During the weekend (Saturday and Sunday) 4:00-08:00 zz z 08:00-3:30 3:30-4:00 zz z Note: when you set a time interval, the interval end time must always be later than the start time. If you need to set the same temperature bridging one day and the next you must create programs (e.g. the two night profiles of the just created program). The next section will show you how to make the same program configuring it manually 44

45 Create a program using the manual procedure By means of the manual configuration you can create a program defining the various parameters which make up the program (temperature levels, time intervals and days of application) specifically and in a totally free way. We will thus see how to create the same program already created with the guided configuration which satisfies the following settings: During the week (from Monday to Friday) During the weekend (Saturday and Sunday) 4:00-08:00 3:30-4:00 08:00-09:00 4:00-08:00 09:00-9:30 08:00-3:30 9:30-3:30 3:30-4:00 45

46 3 4 Touch to create a new program Touch to create it manually 3 Enter a name for the program 4 Touch to set a weekly program Neutral profiles are created (temperature of 7 C for all the 4 hours) one for every day of the week Touch to modify the first profile as needed 6 Touch to add the first interval (00:00 08:00 at 8 C) to adjust the temperature at night 7 Touch to select the temperature 8 Scroll to set the time interval in which the previously set temperature will be active 9 Touch to confirm 46

47 0 3 0 Touch to add the second interval (08:00 09:00 at 0 C) to adjust the temperature from when you wake up to when you go out Touch to select the temperature Scroll to set the time interval in which the previously set temperature will be active 3 Touch to confirm Touch to add the third interval (09:00 9:30 at 6 C) to adjust the temperature when you are out 5 Touch to select the temperature 6 Scroll to set the time interval in which the previously set temperature will be active 7 Touch to confirm 47

48 Touch to add the fourth interval (9:30 3:30 at 0 C) to adjust the temperature when you come home 9 Touch to select the temperature 0 Scroll to set the time interval in which the previously set temperature will be active Touch to confirm Touch to add the fifth interval (3:30 4:00 at 8 C) to adjust the temperature when you go to bed 3 Touch to select the temperature 4 Scroll to set the time interval in which the previously set temperature will be active 5 Touch to confirm 6 Touch to return to the program main page Note: when you set a time interval, the interval end time must always be later than the start time. If you need to set the same temperature bridging one day and the next you must create programs (e.g. first and fifth). 48

49 Now you must copy the profile just created for the week days Touch to activate the copy mode 8 Select the days when you want to copy the profile created on Monday (dot becomes white) 9 From Monday to Friday the profile will be the same, touch to confirm Presuming that habits are different for week days, you can create a specific profile for Saturday and Sunday Touch to modify the Saturday profile 3 Touch to add the first interval (00:00 08:00 at 8 C) to adjust the temperature at night 3 Touch to select the temperature 33 Scroll to set the time interval in which the previously set temperature will be active 34 Touch to confirm 49

50 Touch to add the second interval (08:00 3:30 at 9 C) to adjust the temperature from when you wake up to when you go to bed 36 Touch to select the temperature 37 Scroll to set the time interval in which the previously set temperature will be active 38 Touch to confirm Touch to add the third interval (3:30 4:00 at 8 C) to adjust the temperature when you go to bed. 40 Touch to select the temperature 4 Scroll to set the time interval in which the previously set temperature will be active 4 Touch to confirm 43 Touch to return to the program main page 50

51 Now you must copy the just created profile in Sunday Touch to activate the copy mode 45 Select Sunday (the dot turns white) 46 Touch to confirm A Touch to send the program to the device After a few seconds a confirmation message will indicate that the procedure has been successful. A Now the program appears in the program list and can be activated 5

52 Copy a program Via this function you can copy and if necessary modify an existing program 4 3 Touch to create a new program using duplication Touch to start the procedure 3 Select the program to copy 4 Touch to confirm 5 A Enter a description and if necessary modify the program 6 Touch to send the program to the device After a few seconds a confirmation message will indicate that the procedure has been successful. A Now the program appears in the program list and can be activated, modified or deleted 5

53 Modify a program You can modify a program editing the set profiles Touch to modify a program You can now modify the profiles or copy them, at the end: Touch to send the program to the device After a few seconds a confirmation message will indicate that the procedure has been successful. 53

54 Modify the profile 3 4 Touch to modify the desired profile Touch to create a new interval or 3 Modify the existing interval by scrolling until the interval to be modified is displayed 4 Touch the interval to modify Scroll to modify the interval start and finish times or 6 Touch the bin icon to delete the interval 7 Touch to confirm 8 Touch to end 54

55 9 9 The profile has been modified Copy a profile 3 Touch to select the profile to copy Select the profiles to replace In this example the Monday profile is repeated on Tuesday and Wednesday as well 3 Touch to confirm 55

56 Activate a program After creating the programs you must activate the one you want Touch to activate the program After a few seconds a confirmation message will indicate that the procedure has been successful The program is now active on your Smarther 56

57 Users In this section you can display the users who can interact with your system, invite new ones or if necessary delete them (the user will not be deleted, just the possibility of interacting with this system). After the user you have invited has registered on the portal, logged in and accepted the invitation, he will appear in the list. A B 3 Touch to open the pull-down menu Touch to open the User section A User list B Delete a user 3 Touch to invite another user Enter the of the user to invite and confirm it 5 Touch to send the invitation 6 Touch to exit 57

58 The invited user will receive an with the invitation to check your system and register following the procedure, authenticate ( A ), and accept the invitation ( B ). A B C At this point you will find him in the list of associated account ( C ). 58

59 Settings In this section you can display the Smarthers installed in your home and add the firmware. Touch to open the pull-down menu Touch to open the setting section In this page you display the home Smarthers and can add new ones A 3 B 3 Touch the Smarther whose settings you want to modify A Display/modify Smarther name B Firmware update 59

60 Modify the Smarther name Touch to modify the description Touch to send the modification to the Smarther Smarther Firmware update Touch to check the availability of an update If available, touch to download the update. Do not switch the Smarther off or disconnect it until the end of the procedure At the end touch to update the firmware. Do not switch the Smarther off or disconnect it until the end of the procedure 4 The firmware is now updated. Touch to return to the settings section 60

61 Add a new Smarther and/or a new house With this function you can add a new Smarther to an existing home, or create a new one and add it to it. You can create and manage up to 4 Smarthers for each home and create and manage up to 4 houses. 4 3 Touch to add a new Smarther Touch to continue 3 Touch to continue or 4 Touch when you want to add it to another home or create a new one 5 Touch to start the association 6 At the end touch to enter a description of the Smarther. 7 Touch to end 6

62 9 0 8 In this case the Smarther, being new, is in off mode (set with a default temperature 7 C winter/35 C summer) 8 You can now display the two home Smarthers. Touch to open the Home Page of the Smarther you want to manage 9 Touch to delete the existing programming 0 Touch to set the temperature Caution: to delete the association of a Smarther from the App, you must: - make sure that it is connected to the internet via Wi-Fi; - perform the reset procedure; 3 - exit the App and repeat the authentication 6

63 Help In this section you can display the after-sales service contacts page and send a notification about a problem you have found. Touch to open the pull-down menu Touch to open the help section Assistance Touch to display the page of the Support Service contacts. You will be readdressed on the site 63

64 Log management 3 Touch to point out a problem which has occurred and send a notification to the after-sales service Describe the problem you want to point out in the correct field 3 Touch to send the message to the after-sales service 64

65 65

66 BTicino SpA Viale Borri, 3 00 Varese BTicino Spa reserves at any time the right to modify the contents of this booklet and to communicate, in any form and modality, the changes brought to the same.