FISP Programming: Pri: V1.90 & Sec: V1.70

Transcription

1 FISP Programming: Pri: V1.90 & Sec: V1.70 Bulletin Number: Revision: A Bulletin Date: 05/12/2008 Revision Date: Applies to Models: Pro Series Treadmills , 5600, 6500, 6600 This document will guide you through the programming of an FISP Uploader in preparation of updating the display software in the Pro Series treadmills (5500, 5600, 6500, 6600). Use the settings in this document when uploading software Primary version 1.90 and Secondary version Note: Two FISP uploaders are required to update the software in the Pro Series treadmills. Caution: Incorrect settings will cause the product to be non-operational. When updating a product with Primary and Secondary softwares, the Primary must be updated first. To program the Uploaders to install software into the Pro Series treadmills, there are two steps for each version: Mega103 and Mega128. Follow the next steps to program the Primary and Secondary versions of 9 Rev: A

2 PRIMARY Prg 1 (Mega103) Set the Device to Mega103. Fig. 1-1 Click in the Flash Filename field, then select the software version to be programmed into the Uploader. Be sure to put a label on the Uploader as a reminder as to the version it is programmed with. Flash Filename: C:\AVRISP\software_pro-tr-pri_v1.90 Fig. 1-2 Click on the Device Options button. Fig of 9 Rev: A

3 Primary Lock and Fuse Bits Settings Prg 1 (Mega103) Make sure to check and uncheck the correct boxes in each of the five tabs: Lock Bits, Fuse Bits, Fuse Bits High, Fuse Bits Extended and Calib Osc. Lock Bits Fuse Bits Fig. 2-1 Fig. 2-2 Fuse Bits High Fuse Bits Extended Fig. 2-3 Fig. 2-4 Calib Osc Fig of 9 Rev: A

4 PRIMARY Prg 2 (Mega128) Click the Prg dropdown arrow and select 2. Fig. 3-1 On Prg line 2, set the Device to Mega128. Fig. 3-2 On Prg line 2, click in the Flash Filename field, then select the software version to be programmed into the Uploader. Be sure to put a label on the Uploader as a reminder as to the version it is programmed with. Flash Filename: C:\AVRISP\software_pro-tr-pri_v1.90 Fig. 3-3 On Prg line 2, click on the Device Options button. Fig of 9 Rev: A

5 Primary Lock and Fuse Bits Settings Prg 2 (Mega128) Make sure to check and uncheck the correct boxes in each of the five tabs: Lock Bits, Fuse Bits, Fuse Bits High, Fuse Bits Extended and Calib Osc. Lock Bits Fuse Bits Fig. 4-1 Fig. 4-2 Fuse Bits High Fuse Bits Extended Fig. 4-3 Fig. 4-4 Calib Osc Fig of 9 Rev: A

6 SECONDARY Prg 1 (Mega103) Set the Device to Mega103. Fig. 5-1 Click in the Flash Filename field, then select the software version to be programmed into the Uploader. Be sure to put a label on the Uploader as a reminder as to the version it is programmed with. Flash Filename: C:\AVRISP\software_pro-tr-sec_v1.70 Fig. 5-2 Click on the Device Options button. Fig of 9 Rev: A

7 Secondary Lock and Fuse Bits Settings Prg 1 (Mega103) Make sure to check and uncheck the correct boxes in each of the five tabs: Lock Bits, Fuse Bits, Fuse Bits High, Fuse Bits Extended and Calib Osc. Lock Bits Fuse Bits Fig. 6-1 Fig. 6-2 Fuse Bits High Fuse Bits Extended Fig. 6-3 Fig. 6-4 Calib Osc Fig of 9 Rev: A

8 SECONDARY Prg 2 (Mega128) Click the Prg dropdown arrow and select 2. Fig. 7-1 On Prg line 2, set the Device to Mega128. Fig. 7-2 On Prg line 2, click in the Flash Filename field, then select the software version to be programmed into the Uploader. Be sure to put a label on the Uploader as a reminder as to the version it is programmed with. Flash Filename: C:\AVRISP\software_pro-tr-sec_v1.70 Fig. 7-3 On Prg line 2, click on the Device Options button. Fig of 9 Rev: A

9 Secondary Lock and Fuse Bits Settings Prg 2 (Mega128) Make sure to check and uncheck the correct boxes in each of the five tabs: Lock Bits, Fuse Bits, Fuse Bits High, Fuse Bits Extended and Calib Osc. Lock Bits Fuse Bits Fig. 8-1 Fig. 8-2 Fuse Bits High Fuse Bits Extended Fig. 8-3 Fig. 8-4 Calib Osc Fig of 9 Rev: A