PN2. Copyright 2013, ifm electronic gmbh. Vendor ID / 0x Bytes: / 0x00 0x00 0x49

Transcription

1 Verion: V.4. Releae Date: Copyright 23, ifm electnic gmbh PN2 Vendor ID Vendor Vendor Text Vendor URL Device ID 3 / x36 - Byte: 54 / x x36 ifm electnic gmbh / x49 - Byte: 73 / x x x49 Communication IO-Link Reviion Minimum Cycle Time SIO Mode Supported V. 2.3 m Ye Device Variant PN2228 PN2228 electnic preure enor -5. to.4 inh2o Page

2 Pce Data (PceDataIn) Total Bit = 6 Datatype Bitoffet Bitlength Offet Preure Fig. PDV. Current ytem preure. The real preure can be calculated a follow: P_real = (PDV >> Bitoffet) * + Offet. ('>>' mean Bithift to the right) IntegerT to 4. Switchtate [OUT2] Fig. BDC2. State depend on [OU2], inactive if [OU2] i et to [I] or [U]. BooleanT (fale) inactive (true) active Switchtate [OUT] Fig. BDC.State depend on [OU]. BooleanT (fale) inactive (true) active Page 2

3 Variable bitoffet Acce Right Offet Sytem Command 2 wo Vendor 6 ifm electnic gmbh Vendor Text 7 Pduct 8 PN2228 Serial Number 2 Hardware Reviion 22 Firmware Reviion 23 Application Specific 24 3 Byte Pce Data In 4 SP Switch point, [SP] hall be greater than [rp] to 4. rp Reet point, [rp] hall be maller than [SP] to. OU Output configuration 69 4 (4) Hno (8) Hnc (6) Fno (32) Fnc OU2 Output configuration 2 7 () I (2) U (4) Hno Page 3

4 Variable bitoffet Acce Right Offet OU2 Output configuration 2 7 (8) Hnc (6) Fno (32) Fnc SP2 Switch point 2, [SP2] hall be greater than [rp2]. [SP2] will only be applied if [OU2] i in witching mode to 4. rp2 Reet point 2, [rp2] hall be maller than [SP2]. [rp2] will only be applied if [OU2] i in witching mode to. ASP Analog Start Point (the ditance of [ASP] - [AEP] hall be at leat 25% of the meaurement range). [ASP] hall be maller than [AEP]. [ASP] will only be applied if [OU2] i et to [I] or [U] 73-5 to 754. AEP Analog End Point (the ditance of [ASP] - [AEP] hall be at leat 25% of the meaurement range). [AEP] hall be greater than [ASP]. [AEP] will only be applied if [OU2] i et to [I] or [U] to 4. HI Highet meaured value to 32. LO Lowet meaured value to 32. COF Zepoint calibration (Calibration offet) 79-5 to 5. % Page 4

5 Variable bitoffet Acce Right Offet ds Switch-On delay [OUT] 8 to 5. dr Switch-Off delay [OUT] 82 to 5. ds2 Switch-On delay [OUT2]. Only take effect if [OUT2] i in witching mode 83 to 5. dr2 Switch-Off delay [OUT2]. Only take effect if [OUT2] i in witching mode 84 to 5. dap Damping pce value, take effect on witching output and diplay 86 6 to 4. daa Damping analog output and IO-Link pce value 87 to 4. dis Diplay etting 88 6 Diplay ON / OFF bitoff 7 Bit fale (fale) ON (true) OFF Diplay tated ye / no bitoff 6 Bit fale (fale) Not tated (true) Rotated Update rate bitoff 3 Bit 2 () Fat update (2) Medium update (4) Slow update Uni Shown unit on the enor diplay 89 3 () mbar () kpa (2) mmws (3) inh2o Page 5

6 Variable bitoffet Acce Right Offet S.Loc Key modify lock, only reettable fm remote 99 () locked () unlocked Loc Key modify lock, reettable at the device () locked () unlocked Meage Perform action on the enor 24 wo 253 (246) Reet [LO] memory (247) Reet [HI] memory (253) Factory Reet Page 6

7 Event Code Type Mode No event Meage - 66 Parametrization err Range overflow Warning Decreae preure Range underflow Warning Increae preure 7936 Range over- / underflow Increae or decreae preure 83 Parametrization err SP 84 Parametrization err rp 85 Parametrization err OU 86 Parametrization err OU2 87 Parametrization err SP2 88 Parametrization err rp2 89 Parametrization err ASP 8 Parametrization err AEP 7938 Parametrization err ditance ASP - AEP 85 Parametrization err COF 87 Parametrization err ds 88 Parametrization err dr 89 Parametrization err ds2 82 Parametrization err dr2 822 Parametrization err dap 823 Parametrization err daa 824 Parametrization err dis 825 Parametrization err Uni 835 Parametrization err S.Loc 836 Parametrization err Loc Page 7