Communication. Features. Device variant. Copyright 2018, Builder: , Time: 02:11:09

Transcription

1 Version V Release date Copyright 218, Builder: , Time: 2:11:9 O6 Vendor ID Device ID Vendor name Vendor text Vendor URL 31 / x136 - s: 1 54 / x1 x / x2e - s: 2 14 / x x2 xe ifm electnic gmbh Communication IO-Link revision Bit rate Minimum cycle time SIO mode supported Features Block parametrization Data storage V1.1 COM2 1. ms Yes Yes Yes Device variant O6H7 Photoelectric sensor, mm O6H71 Photoelectric sensor, mm Page 1

2 Device variant O6H72 Photoelectric sensor, mm O6H73 Photoelectric sensor, mm O6H74 Photoelectric sensor, mm O6H75 Photoelectric sensor, mm Page 2

3 Pcess data (Pcess data input) Total bit length = 32 Description Bit length Distance Current object distance IntegerT to 11 (-3276) UL (3276) OL (32764) NoData.1 mm Device status Current device status, a copy of the variable [Device Status] in the pcess data channel 4 () Device is OK (1) Maintenance required (2) Out of specification (3) Functional check (4) Failure SSC1 Status depends on SSC1-Config.Logic and SSC1-Config.Mode (false) inactive (true) active Page 3

4 Standard Command 2 wo (13) Restore Factory Settings (65) Teach SP1 (67) Teach SP TP1 (68) Teach SP TP2 (75) Teach Custom - Backgund (79) Teach cancel (24) IO-Link 1.1 system test command 24, Event 8DFE appears (241) IO-Link 1.1 system test command 241, Event 8DFE disappears (242) IO-Link 1.1 system test command 242, Event 8DFF appears (243) IO-Link 1.1 system test command 243, Event 8DFF disappears Device Locks 12 RecordT Data Storage bitoffs 1 (false) (false) Unlocked (true) Locked Local Parameterization bitoffs 2 (false) (false) Unlocked (true) Locked Vendor 16 max 19 ifm electnic gmbh Vendor Text 17 max 11 Page 4

5 Pduct 18 max 6 Pduct ID 19 max 6 Pduct Text 2 max 29 Backgund Suppression Sensor Serial Number 21 max 12 Hardware Version 22 max 8 Firmware Version 23 max 8 Application Specific Tag 24 max 32 *** Page 5

6 Device Status 36 () Device is OK () Device is OK (1) Maintenance required (2) Out of specification (3) Functional check (4) Failure 5 to 255 (Reserved) Detailed Device Status 37 ArrayT 24 h TI Select Teach selection 58 (1) SSC1 (1) SSC1 TI Result Teach result 59 RecordT Flag SP1 TP2, Feedback for SP1, teach point 2 bitoffs 5 () Nok () Nok (1) Ok Flag SP1 TP1, Feedback for SP1, teach point 1 bitoffs 4 () Nok () Nok (1) Ok State, Current teach state bitoffs 4 Bit () Idle () Idle (1) SP1 Success (4) Wait for command (5) Busy (7) Err Page 6

7 SSC1 Param Switching signal channel 1, parameter 6 RecordT 32 Bit SP1, Setpoint 1 Sub 1 IntegerT (32752) Load 17 to 11 (32752) Load.1 mm SP2, Setpoint 2 Sub 2 IntegerT () N.A. () N.A. SSC1 Config Logic, Setpoint logic / State for target detected Mode, Setpoint mode Hysteresis, Setpoint hysteresis Switching signal channel 1, configuration 61 Sub 1 Sub 2 Sub 3 RecordT IntegerT 32 Bit () High active (1) Single point () N.A. () High active (1) Low active (1) Single point () N.A. SSC1 Switch-On delay Switchching signal channel 1, Switch-On delay 37 to 2.1 s SSC1 Switch-Off delay Switchching signal channel 1, Switch-Off delay 371 to 2.1 s Power cycles Number of power cycles since delivery 541 to Operating hours Counter of the operating hours since delivery 542 to h Page 7

8 Active Events Bit mask for current pending events 545 RecordT 32 Bit Bit_31, Bit 31 indicates the assigned pending event bitoffs 31 () noev () noev (1) x8dff Bit_3, Bit 3 indicates the assigned pending event bitoffs 3 () noev () noev (1) x8dfe Param configuration fault Displays the wngly set parameters 546 ArrayT 1 * 32 Bit () OK (786432) DeviceLocks ( ) ApplicationSpecificTag (38188) TI-Select (393216) SSC1-Param ( ) SSC1-Param.SP1 ( ) SSC1-Param.SP2 ( ) SSC1-Config ( ) SSC1-Config.Logic ( ) SSC1-Config.Mode ( ) SSC1-Config.Hyst ( ) SSC1_dS ( ) SSC1_dr (36448) Loc ( ) SEQ (13172) Transmitter_Configuration ( ) ModE Page 8

9 Loc [Loc] locks the local user interface to prevent unintentional changes, [Loc] is resettable at the device 55 (1) uloc () Loc (1) uloc ModE Operating mode 684 () Switching () Switching (1) Measuring Sequence modulation Modulation of transmitter signal. Setting affects the mutual interference with other sensors. 69 () OFF () OFF (255) AUTo Transmitter configuration Configuration transmitter light 2 (1) On / On () Off / Off (1) On / On Events Code Type Description 3635 d / 8D FE h Test Event 1. Device Status = 1 (Maintenance required) Warning Event appears by setting index 2 to value 24, Event disappears by setting index 2 to value d / 8D FF h Test Event 2. Device Status = 1 (Maintenance required) Warning Event appears by setting index 2 to value 242, Event disappears by setting index 2 to value 243 Page 9

10 Err types Err code d / 8 h d / 8 11 h d / 8 12 h 328 d / 8 2 h 3281 d / 8 21 h 3282 d / 8 22 h 3283 d / 8 23 h d / 8 3 h d / 8 31 h d / 8 32 h d / 8 33 h 3282 d / 8 34 h d / 8 35 h d / 8 36 h d / 8 4 h d / 8 41 h d / 8 82 h Device application err - no details not available not available Service temporarily not available Service temporarily not available - local contl Service temporarily not available - device contl denied Parameter value out of range Parameter value above limit Parameter value below limit Parameter length overrun Parameter length underrun Function not available Function temporarily unavailable Invalid parameter set Inconsistent parameter set Application not ready Description Service has been refused by the device application and no detailed information of the incident is available occurs to a not existing index occurs to a not existing subindex Parameter is not accessible due to the current state of the device application Parameter is not accessible due to an ongoing local operation at the device Parameter is not accessible due to a remote triggered state of the device application Write access on a read-only parameter Written parameter value is outside its permitted value range Written parameter value is above its specified value range Written parameter value is below its specified value range Written parameter length is above its predefined length Written parameter length is below its predefined length Written command is not supported by the device application Written command is not available due to the current state of the device application Written single parameter collides with other actual parameter settings Parameter inconsistencies were found at the end of block parameter transfer, device plausibility check failed Read or write service is refused due to a temporarily unavailable application Page 1