Communication. Features. Device variant. Copyright 2017, Builder: , Time: 10:07:14

Transcription

1 Version V Release date Copyright 27, Builder: , Time: :7:4 UG Vendor ID Device ID Vendor name Vendor text Vendor URL 3 / x36 - s: 54 / x x36 7 / x2bd - s: 2 89 / x x2 xbd ifm electnic gmbh Counication IO-Link revision Bit rate Minimum cycle time SIO mode supported Features Block parametrization Data storage V. COM2 3.2 ms Yes Yes Yes Device variant UGT26 UGT52 Page

2 Page 2

3 Pcess data (Pcess data input) Total bit length = 32 Bit offset Bit length PDV Current pcess data IntegerT to 23 (-3276) UL (3276) OL Device status Current device status, a copy of the variable [Device Status] in the pcess data channel 4 4 () Device is OK () Maintenance required (2) Out of specification (3) Functional check (4) Failure OUT2 Status depends on SSC2-Config.Logic and SSC2-Config.Mode (false) inactive (true) active OUT Status depends on SSC-Config.Logic and SSC-Config.Mode (false) inactive (true) active Page 3

4 Standard Coand 2 wo (3) Restore Factory Settings (65) Teach SP (66) Teach SP2 (24) IO-Link. system test coand 24, Event 8DFE appears (24) IO-Link. system test coand 24, Event 8DFE disappears (242) IO-Link. system test coand 242, Event 8DFF appears (243) IO-Link. system test coand 243, Event 8DFF disappears Device Locks 2 6 Bit Data Storage Unlocked: Parameter are saved in IO-Link masters memory. Locked: Saving of parameters in the IO-Link master is not possible. [INFO] Concerning this parameter, IO-Link master and device have to be configured the same way. An activated DataStorage within the masters bitoffs Bit (false) (false) Unlocked (true) Locked Page 4

5 Device Locks 2 6 Bit configuration, indicates the devices DataStorageLock to be 'Unlocked'. Local Parameterization bitoffs 2 Bit (false) (false) Unlocked (true) Locked Vendor of the vendor of the device. 6 max 9 ifm electnic gmbh Vendor Text Additional information of the devices vendor. 7 max Pduct 8 max 6 Pduct ID 9 max 6 Pduct Text 2 max 26 Ultrasonic Distance Sensor Serial Number 2 max 6 Hardware Version 22 max 2 Firmware Version 23 max 6 Application Specific Tag A freely defined text can be assigned. 24 max 32 *** Device Status 36 () Device is OK () Device is OK () Maintenance required Page 5

6 Device Status 36 () Device is OK (2) Out of specification (3) Functional check (4) Failure 5 to 255 (Reserved) Detailed Device Status h TI Select Teach selection 58 () SSC () SSC (2) SSC2 TI Result Teach result 59 State Current teach state bitoffs 4 Bit () Idle () Idle () SP Success (2) SP2 Success (3) SP2 Success (5) Busy (7) Err SSC Param Switching signal channel, parameter 6 SP Setpoint Sub IntegerT 6 Bit (2) 2 to 22 SP2 Setpoint 2 Sub 2 IntegerT 6 Bit (2) 2 to 22 SSC Config Switching signal channel, configuration 6 Logic Setpoint logic / State for target detected Sub () High active () High active () Low active Mode Setpoint mode Sub 2 () Point () Point (2) Window (3) 2Point Page 6

7 SSC Config Switching signal channel, configuration 6 Hyst Setpoint hysteresis Sub 3 IntegerT 6 Bit (5) to 5 SSC2 Param Switching signal channel 2, parameter 62 SP Setpoint Sub IntegerT 6 Bit (22) 2 to 22 SP2 Setpoint 2 Sub 2 IntegerT 6 Bit (2) 2 to 22 SSC2 Config Switching signal channel 2, configuration 63 Logic Setpoint logic / State for target detected Sub () High active () High active () Low active Mode Setpoint mode Sub 2 () Point () Point (2) Window (3) 2Point Hyst Setpoint hysteresis Sub 3 IntegerT 6 Bit (5) to 5 SSC Switch-On delay Switchching signal channel, Switch-On delay 37 6 Bit to 2 ms SSC Switch-Off delay Switchching signal channel, Switch-Off delay 37 6 Bit to 2 ms SSC2 Switch-On delay Switchching signal channel 2, Switch-On delay Bit to 2 ms SSC2 Switch-Off delay Switchching signal channel 2, Switch-Off delay Bit to 2 ms FILT Filter or response time of the measured signal, LOW indicates fast, HIGH indicates slow response 55 (2) MEdI () OFF Page 7

8 FILT Filter or response time of the measured signal, LOW indicates fast, HIGH indicates slow response 55 (2) MEdI () LOW (2) MEdI (3) HIGH Power cycles Number of power cycles since delivery 54 6 Bit to Operating hours Counter of the operating hours since delivery Bit to h Active Events Bit mask for current pending events 545 Bit_3 Bit 3 indicates the assigned pending event bitoffs 3 Bit () noev () noev () x8dff Bit_3 Bit 3 indicates the assigned pending event bitoffs 3 Bit () noev () noev () x8dfe Bit_6 Bit 6 indicates the assigned pending event bitoffs 6 Bit () noev () noev () x42 Bit_2 Bit 2 indicates the assigned pending event bitoffs 2 Bit () noev () noev () x77 Param configuration fault Displays the wngly set parameters 546 Loc [Loc] locks the local user interface to prevent unintentional changes, [Loc] is resettable at the device 55 () uloc () uloc () Loc Page 8

9 ECHO Echo quality 23 () no () LOW (2) MId (3) GOOd (4) ECLT Backgund suppression Backgund suppression 23 () OFF () OFF () On Events Code Type 692 d / 42 h Device temperature over-run Warning Clear source of heat 348 d / 77 h Short circuit Err Check installation 3635 d / 8D FE h Test Event Warning Event appears by setting index 2 to value 24, Event disappears by setting index 2 to value d / 8D FF h Test Event 2 Warning Event appears by setting index 2 to value 242, Event disappears by setting index 2 to value 243 Err types Err code d / 8 h d / 8 h d / 8 2 h 328 d / 8 2 h 3283 d / 8 23 h 3286 d / 8 3 h Device application err - no details not available not available Service temporarily not available denied Parameter value out of range Service has been refused by the device application and no detailed information of the incident is available occurs to a not existing index occurs to a not existing subindex Parameter is not accessible due to the current state of the device application Write access on a read-only parameter Written parameter value is outside its permitted value range Page 9

10 Err types Err code 3289 d / 8 33 h 3282 d / 8 34 h 3282 d / 8 35 h d / 8 36 h d / 8 4 h d / 8 4 h d / 8 82 h Parameter length overrun Parameter length underrun Function not available Function temporarily unavailable Invalid parameter set Inconsistent parameter set Application not ready Written parameter length is above its predefined length Written parameter length is below its predefined length Written coand is not supported by the device application Written coand is not available due to the current state of the device application Written single parameter collides with other actual parameter settings Parameter inconsistencies were found at the end of block parameter transfer, device plausibility check failed Read or write service is refused due to a temporarily unavailable application Page