FE-107 Experimental Validation
|
|
|
- Jason Walters
- 6 years ago
- Views:
Transcription
1 FE-107 Experimental Validation Has your finite element analysis (FEA) software been validated against real-world pressure vessel problems? FE-107 and other PRG software are continuously validated against actual problems faced by practicing engineers. Follow this link for to learn more about an experimental validation of the FE-107 solutions and see how WRC 107 fails to predict accurate stresses in a real world application. Real-world validation of PVP Designs Validation comes in two forms: numerical validations and real-world validations. All FEA programs are numerically validated few are validated against problems you face everyday in the pressure vessel and piping industry. An external load was applied to the nozzle located in an elliptical head as shown below. Strain gauges were placed on the head adjacent to the pad and in the nozzle neck to validate the finite element solution. Details of the Experiment The horizontal vessel was lifted from the bolted cover, resulting in a load of 20,000 lbf. Details of the pressure vessel and nozzle are given below.
2 The next step is to input the model in the FE-107 input screens. FE-107 Input FE-107 s input is specifically designed to make the design and analysis of typical pressure vessel and piping (PVP) geometries with nozzle very easy. Unlike general FEA programs that require the user to create models from scratch, FE-107 creates the model for you using input that is familiar to all PVP engineers. In this case, the geometry can be defined using just 11 input fields as shown below. The required input accompanied by a drawing for each type of model available in FE-107. This makes it very easy to understand the input. Next, the orientation and loads are defined. FE-107 can accommodate any orientation of the head and nozzle.
3 Some other features: 1. Loads can be specified using WRC conventions or in a user defined convention. 2. Loads can be defined at the centerline, nozzle-shell junction, or end of the nozzle. 3. Input for weight, operating, and occasional loads. 4. Specify the number of fatigue cycles for an automatic fatigue analysis of external loads and pressure. Run the Analysis To start the analysis, the user clicks the Run icon located on the FE-107 toolbar. FE-107 will automatically construct the model, apply the loads, and boundary conditions based on the user s input. You don t need to be an FEA expert to use FE-107.
4 During the analysis, FE-107 will give the user useful information and provide alerts when assumptions must be made. In this case, neither WRC-107 nor WRC-297 methods are ideally suited for the analysis since the nozzle is located in an elliptical head. Analysis Results WRC 107 FAILS The following are the comparative results between the experimental stresses, FE-107 s FEA solution, and the WRC-107 & WRC-297 comparisons. As shown below, FE-107 predicts conservative and accurate stresses in all cases. WRC-107 fails the validation by significantly over predicting the stresses in the pad and not providing any stress calculation for the highest stresses which occur in the nozzle neck. This clearly shows why the WRC methods are not adequate for PVP designs. Can you afford to miss the highest stress by a factor of 4.0 using outdated analysis methods? Location Strain Gage Results FEA Results WRC-107 WRC-297 Shell near pad weld 7000 psi ( psi ( psi (109 Not applicable Pad near nozzle weld psi ( psi ( psi (109 Not applicable Nozzle neck near nozzle weld psi ( psi (446 Not available Not applicable FE-107 Output The FE-107 results are presented in an easy to use interface and include ASME Code compliance reporting.
5 Some features of the FE-107 output: 1. Finite element results are given in three easy to use formats (spreadsheets, printable reports, 3D interactive graphics) 2. Automatic ASME stress classification no other FEA software offers this for shell elements. 3. Automatic ASME Code compliance reports 4. Comparisons against WRC-107 and WRC-297 methods More FE-107 Output Screens
6 Interactive 3-D graphical results for evaluating results.
7 A text report is provided for documentation and distribution to clients and inspectors. The report includes drawings, dimensions, tabulated stresses, and graphical results
8 A text report is provided for documentation and distribution to clients and inspectors. The report includes drawings, dimensions, tabulated stresses, and graphical results (contd.)
9 FE-107 also provides allowable loads and flexibility results for the nozzle. Flexibilities can be used by piping engineers for more accurate piping analysis.
10 FE-107 also provides allowable loads and flexibility results for the nozzle. Flexibilities can be used by piping engineers for more accurate piping analysis. (contd.)
11 Automatic comparisons between FE-107, WRC-107, and WRC-297 are given to show when the WRC methods are not appropriate.
ASME Verification and Validation Symposium May 13-15, 2015 Las Vegas, Nevada. Phillip E. Prueter, P.E.
VVS2015-8015: Comparing Closed-Form Solutions to Computational Methods for Predicting and Validating Stresses at Nozzle-to-Shell Junctions on Pressure Vessels Subjected to Piping Loads ASME Verification
MAE 323: Lab 7. Instructions. Pressure Vessel Alex Grishin MAE 323 Lab Instructions 1
Instructions MAE 323 Lab Instructions 1 Problem Definition Determine how different element types perform for modeling a cylindrical pressure vessel over a wide range of r/t ratios, and how the hoop stress
Krzysztof Dabrowiecki, Probe2000 Inc Southwest Test Conference, San Diego, CA June 08, 2004
Structural stability of shelf probe cards Krzysztof Dabrowiecki, Probe2000 Inc Southwest Test Conference, San Diego, CA June 08, 2004 Presentation Outline Introduction Objectives Multi die applications
PV Elite 2011 version Quick Start Page 1-21
PV Elite 2011 version Quick Start Page 1-21 INTRODUCTION The 2009 version of PV Elite introduces an updated user interface. The interface is the area on the screen where you, the user enter all the information
3D Finite Element Software for Cracks. Version 3.2. Benchmarks and Validation
3D Finite Element Software for Cracks Version 3.2 Benchmarks and Validation October 217 1965 57 th Court North, Suite 1 Boulder, CO 831 Main: (33) 415-1475 www.questintegrity.com http://www.questintegrity.com/software-products/feacrack
Available Services for Small Bore Connections (SBC)
Evaluation of vibration induced fatigue failure on SBCs for new projects (design) or existing piping systems Vibration induced failures on Small Bore Connections (SBCs) are the most common integrity issues
Tutorial on Qualification of Nozzles attached to Spherical/Cylindrical Vessels using CAEPIPE
Tutorial on Qualification of Nozzles attached to Spherical/Cylindrical Vessels using CAEPIPE The following are the steps for qualifying nozzles welded to Spherical/Cylindrical Vessels such as pressure
Multi-Body Simulation of Earthmoving Equipment using MotionView / MotionSolve
Multi-Body Simulation of Earthmoving Equipment using MotionView / MotionSolve Amit Srivastava Manager Larsen & Toubro IES Knowledge City, NH8 Vadodara 390 019, India Gopikrishnan. M Assistant Manager Larsen
Standard Operating Procedure for the Discovery Hybrid Rheometer HR-3
Standard Operating Procedure for the Discovery Hybrid Rheometer HR-3 Page 1 of 5 Edited on 01/02/2019 Coral Reservations - The Discovery Hybrid Rheometer is on the CCMR Coral Equipment Reservation and
EN1740 Computer Aided Visualization and Design Spring /26/2012 Brian C. P. Burke
EN1740 Computer Aided Visualization and Design Spring 2012 4/26/2012 Brian C. P. Burke Last time: More motion analysis with Pro/E Tonight: Introduction to external analysis products ABAQUS External Analysis
Impact of 3D Laser Data Resolution and Accuracy on Pipeline Dents Strain Analysis
More Info at Open Access Database www.ndt.net/?id=15137 Impact of 3D Laser Data Resolution and Accuracy on Pipeline Dents Strain Analysis Jean-Simon Fraser, Pierre-Hugues Allard Creaform, 5825 rue St-Georges,
ASSET INTEGRITY MANAGEMENT
ASSET INTEGRITY MANAGEMENT Ensuring the Integrity, Safety and Reliability of Plant OBJECTIVES OF ASSET OWNERS Regulatory Compliance Maximise production Reduce lost income due to unplanned shutdowns Optimise
SIMULATION CAPABILITIES IN CREO
SIMULATION CAPABILITIES IN CREO Enhance Your Product Design with Simulation & Using digital prototypes to understand how your designs perform in real-world conditions is vital to your product development
(Based on a paper presented at the 8th International Modal Analysis Conference, Kissimmee, EL 1990.)
Design Optimization of a Vibration Exciter Head Expander Robert S. Ballinger, Anatrol Corporation, Cincinnati, Ohio Edward L. Peterson, MB Dynamics, Inc., Cleveland, Ohio David L Brown, University of Cincinnati,
Global to Local Model Interface for Deepwater Top Tension Risers
Global to Local Model Interface for Deepwater Top Tension Risers Mateusz Podskarbi Karan Kakar 2H Offshore Inc, Houston, TX Abstract The water depths from which oil and gas are being produced are reaching
An Introductory SIGMA/W Example
1 Introduction An Introductory SIGMA/W Example This is a fairly simple introductory example. The primary purpose is to demonstrate to new SIGMA/W users how to get started, to introduce the usual type of
Lecture 3 : General Preprocessing. Introduction to ANSYS Mechanical Release ANSYS, Inc. February 27, 2015
Lecture 3 : General Preprocessing 16.0 Release Introduction to ANSYS Mechanical 1 2015 ANSYS, Inc. February 27, 2015 Chapter Overview In this chapter we cover basic preprocessing operations that are common
AUTOPIPE NOZZLE. LOCAL STRESS ANALYSIS V8i Release Tutorial with Examples
AUTOPIPE NOZZLE LOCAL STRESS ANALYSIS V8i Release 8.11 Tutorial with Examples 1 Table of Contents List of Examples... 2 Example 1: The basic operating procedures of AutoPIPE Nozzle... 3 Starting AutoPIPE
A pipe bend is subjected to a concentrated force as shown: y All dimensions in inches. Material is stainless steel.
Problem description A pipe bend is subjected to a concentrated force as shown: y 15 12 P 9 Displacement gauge Cross-section: 0.432 18 x 6.625 All dimensions in inches. Material is stainless steel. E =
Introduction to C omputational F luid Dynamics. D. Murrin
Introduction to C omputational F luid Dynamics D. Murrin Computational fluid dynamics (CFD) is the science of predicting fluid flow, heat transfer, mass transfer, chemical reactions, and related phenomena
Parametric Piping Models. Naveed Anwar July 2003
Parametric Piping Models Naveed Anwar July 2003 The Idea Basic idea is to assign parametric objects to basic line or area objects in the SAP2000 model and then generate detailed mesh for each object, on-demand
Structural re-design of engine components
Structural re-design of engine components Product design cycle Design Development Testing Structural optimization Product knowledge Design freedom 2/18 Structural re-design of engine components Product
Fatigue of Welds in fe-safe. fe-safe 2017
Fatigue of Welds in fe-safe fe-safe 2017 About this Course Course objectives Upon completion of this course you will be able to: Set up and run various weld fatigue analyses using fe-safe including Understand
Collapse Testing and Modeling of Perforating Guns Carriers. NAPS AUTHORS: Tomas Turkalj, Maurizio Bellingardi, Sebastian Cravero
Collapse Testing and Modeling of Perforating Guns Carriers NAPS-47-18 AUTHORS: Tomas Turkalj, Maurizio Bellingardi, Sebastian Cravero Introduction Gun steel tubular carriers of the Perforating guns have
Engineering Analysis
Engineering Analysis with SOLIDWORKS Simulation 2018 Paul M. Kurowski SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites
AN OVERVIEW AND VALIDATION OF THE FITNESS-FOR-SERVICE ASSESSMENT PROCEDURES FOR LOCAL THIN AREAS. A Thesis. Presented to
AN OVERVIEW AND VALIDATION OF THE FITNESS-FOR-SERVICE ASSESSMENT PROCEDURES FOR LOCAL THIN AREAS A Thesis Presented to The Graduate Faculty of the University of Akron In Partial Fulfillment of the Requirements
Finite Element Analysis Using Pro/Engineer
Appendix A Finite Element Analysis Using Pro/Engineer A.1 INTRODUCTION Pro/ENGINEER is a three-dimensional product design tool that promotes practices in design while ensuring compliance with industry
SOLIDWORKS Simulation
SOLIDWORKS Simulation Length: 3 days Prerequisite: SOLIDWORKS Essentials Description: SOLIDWORKS Simulation is designed to make SOLIDWORKS users more productive with the SOLIDWORKS Simulation Bundle. This
SIMULATION CAPABILITIES IN CREO. Enhance Your Product Design with Simulation & Analysis
SIMULATION CAPABILITIES IN CREO Enhance Your Product Design with Simulation & Using digital prototypes to understand how your designs perform in real-world conditions is vital to your product development
16 SW Simulation design resources
16 SW Simulation design resources 16.1 Introduction This is simply a restatement of the SW Simulation online design scenarios tutorial with a little more visual detail supplied on the various menu picks
The CAESAR II Piping Model. How Good Is It?
The CAESAR II Piping Model How Good Is It? Quick Agenda Introduction The digital model What s missing in our CAESAR II model? Model precision and construction tolerances Engineering Sensitivity Boundary
PV Elite. System Requirements. Version: 2018 ( ) Date: 27 November 2017
PV Elite Product: PV Elite (PVE) Version: 2018 (20.00.00.0000) Date: 27 November 2017 Description: Sections: Intergraph PV Elite analyzes and design pressure vessels and heat exchangers in accordance with
PragTic. in Fatigue Analyses. Jan Papuga
PragTic Use of Finite Element Analysis Data in Fatigue Analyses Jan Papuga The organisation of the meeting is partially financed from OPPI programme Czech Technology Airspace Platform, reg. number SPTP
FEA of Pressure Vessel and Nozzle Junction DHARMIT THAKORE MOONISH ENTERPRISES PTY LTD
2013 FEA of Pressure Vessel and Nozzle Junction DHARMIT THAKORE MOONISH ENTERPRISES PTY LTD Executive Summary The main objective of this project was to understand the Finite Element Analysis capability
Streamlining the CAE Durability Process
Streamlining the CAE Durability Process Product Details Product Overview: ncode DesignLife provides fatigue life prediction from finite element results to answer the question how long will it last? or
Complete and robust mechanical simulation solution. imaginit.com/simulation-mechanical
Complete and robust mechanical simulation solution A mechanical simulation solution for finite element analysis powered by the Autodesk Nastran solver Accurately predict product behavior, optimize and
Lesson 6: Assembly Structural Analysis
Lesson 6: Assembly Structural Analysis In this lesson you will learn different approaches to analyze the assembly using assembly analysis connection properties between assembly components. In addition
Visit the following websites to learn more about this book:
Visit the following websites to learn more about this book: 6 Introduction to Finite Element Simulation Historically, finite element modeling tools were only capable of solving the simplest engineering
The part to be analyzed is the bracket from the tutorial of Chapter 3.
Introduction to Solid Modeling Using SolidWorks 2007 COSMOSWorks Tutorial Page 1 In this tutorial, we will use the COSMOSWorks finite element analysis (FEA) program to analyze the response of a component
P CP1 MTL Overview of analyses
Overview of structural load and analysis cases in the CP1 MTL - engineering assessment Design Document Document Nr. : D0275384 Version / Revision : 0 / C Status : External check Created on : 28-06-2018
Motion Analysis Case Study
Motion Analysis Case Study Very often, complex motions are desired as part of a solution to some engineering problem. Machines and mechanisms are then designed to produce these motions. Motion generation
VALIDATE SIMULATION TECHNIQUES OF A MOBILE EXPLOSIVE CONTAINMENT VESSEL
VALIDATE SIMULATION TECHNIQUES OF A MOBILE EXPLOSIVE CONTAINMENT VESSEL David Karlsson DYNAmore Nordic AB, Sweden KEYWORDS Hexa, Map, Explosive, LS-DYNA ABSTRACT A Mobile Explosive Containment Vessel (MECV)
ANALYSIS OF THE CORRODED PIPELINE SEGMENTS USING IN-LINE INSPECTION DATA
The 8 th International Conference of the Slovenian Society for Non-Destructive Testing»Application of Contemporary Non-Destructive Testing in Eng ineering«september 1-3, 2005, Portorož, Slovenia, pp. 383-389
Modeling Submerged Structures Loaded by Underwater Explosions with ABAQUS/Explicit
Modeling Submerged Structures Loaded by Underwater Explosions with ABAQUS/Explicit David B. Woyak ABAQUS Solutions Northeast, LLC Abstract: Finite element analysis can be used to predict the transient
About the Author. Acknowledgements
About the Author Dr. Paul Kurowski obtained his M.Sc. and Ph.D. in Applied Mechanics from Warsaw Technical University. He completed postdoctoral work at Kyoto University. Dr. Kurowski is an Assistant Professor
Topology Optimization and Analysis of Crane Hook Model
RESEARCH ARTICLE Topology Optimization and Analysis of Crane Hook Model Thejomurthy M.C 1, D.S Ramakrishn 2 1 Dept. of Mechanical engineering, CIT, Gubbi, 572216, India 2 Dept. of Mechanical engineering,
Modeling and Simulation for Aircraft Structural Repair Using Modern FEA Tools
Modeling and Simulation for Aircraft Structural Repair Using Modern FEA Tools December 19-22, 2011 and January 9-12, 2012 Kuang-Hua Chang, Ph.D. Williams Presidential Professor School of Aerospace and
A Multiple Constraint Approach for Finite Element Analysis of Moment Frames with Radius-cut RBS Connections
A Multiple Constraint Approach for Finite Element Analysis of Moment Frames with Radius-cut RBS Connections Dawit Hailu +, Adil Zekaria ++, Samuel Kinde +++ ABSTRACT After the 1994 Northridge earthquake
Structural analysis for in-service gas pipeline lowering using numerical method
Structural analysis for in-service gas pipeline lowering using numerical method Mochamad Safarudin 1*, Joga Dharma Setiawan 2 1 Mechanical Engineering, Sekolah Tinggi Teknologi Mandala, Indonesia 2 Mechanical
LMS Durability Technologies
Durability Technologies Virtual prototyping solutions for a more efficient and better quality durability engineering process Virtual Prototyping for Durability - BA1806-1 copyright International 1998 Fatigue
CHAPTER 1. Introduction
ME 475: Computer-Aided Design of Structures 1-1 CHAPTER 1 Introduction 1.1 Analysis versus Design 1.2 Basic Steps in Analysis 1.3 What is the Finite Element Method? 1.4 Geometrical Representation, Discretization
COSMOS. Connecting to Accurate, Efficient Assembly Analysis. SolidWorks Corporation. Introduction. Pin Connectors. Bolt Connectors.
WHITE PAPER Connecting to Accurate, Efficient Assembly Analysis CONTENTS Introduction Pin Connectors Bolt Connectors Spring Connectors Spot Weld Connectors 1 2 4 7 8 SolidWorks Corporation INTRODUCTION
COMPUTER AIDED ENGINEERING. Part-1
COMPUTER AIDED ENGINEERING Course no. 7962 Finite Element Modelling and Simulation Finite Element Modelling and Simulation Part-1 Modeling & Simulation System A system exists and operates in time and space.
Latch Spring. Problem:
Problem: Shown in the figure is a 12-gauge (0.1094 in) by 3/4 in latching spring which supports a load of F = 3 lb. The inside radius of the bend is 1/8 in. Estimate the stresses at the inner and outer
Artificial Finger Skin having Ridges and Distributed Tactile Sensors used for Grasp Force Control
Journal of Robotics and Mechatronics Vol., No.,. Artificial Finger Skin having Ridges and Distributed Tactile Sensors used for Grasp Force Control Daisuke Yamada, Takashi Maeno and Yoji Yamada Abstract
Modal Analysis of Exhaust System to Optimize Mounting Hanger Location
Modal Analysis of Exhaust System to Optimize Mounting Hanger Location Chetan D. Gaonkar Assistant Professor, Mechanical Engineering Dpt., DBCE, Margao, Goa Abstract An exhaust system with a superior performance
Fatigue design of welded bicycle frames using a multiaxial criterion
Available online at www.sciencedirect.com Procedia Engineering 34 (2012 ) 640 645 9 th Conference of the International Sports Engineering Association (ISEA) Fatigue design of welded bicycle frames using
DETECTION AND QUANTIFICATION OF CRACKS IN PRESSURE VESSELS USING ESPI AND FEA MODELLS
DETECTION AND QUANTIFICATION OF CRACKS IN PRESSURE VESSELS USING ESPI AND FEA MODELLS J GRYZAGORIDIS, DM FINDEIS, JR MYLES Department of Mechanical Engineering University of Cape Town Abstract Non destructive
Oasys Pdisp. Copyright Oasys 2013
Oasys Pdisp Copyright Oasys 2013 All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping,
Technical Report Example (1) Chartered (CEng) Membership
Technical Report Example (1) Chartered (CEng) Membership A TECHNICAL REPORT IN SUPPORT OF APPLICATION FOR CHARTERED MEMBERSHIP OF IGEM DESIGN OF 600 (103 BAR) 820MM SELF SEALING REPAIR CLAMP AND VERIFICATION
E91 Machine Design: Lab 2
E91 Machine Design: Lab 2 Analysis of Stresses in Machines with FEA Techniques Julian Leland Swarthmore College, Fall 2011 ABSTRACT In this lab, a 3- ton arbor press was modeled and assembled in Solidworks.
RF-PIPING. Add-on Modules for PIPELINES. Program Description
Version February 2016 Programs RF-PIPING Add-on Modules for PIPELINES Program Description All rights, including those of translations, are reserved. No portion of this book may be reproduced mechanically,
C-clamp FEA Analysis
C-clamp FEA Analysis ME 341 students are asked to determine the stresses on the inner and outer surface of a C-clamp at a point on the curved section and the straight section of the clamp. The following
Optimizing the Utility Scale Solar Megahelion Drive End-Cap (Imperial Units)
Autodesk Inventor Tutorial Exercise Optimizing the Utility Scale Solar Megahelion Drive End-Cap www.autodesk.com/sustainabilityworkshop Contents OPTIMIZING THE USS SOLAR TRACKING END CAP... 3 OBJECTIVE...
Offshore Platform Fluid Structure Interaction (FSI) Simulation
Offshore Platform Fluid Structure Interaction (FSI) Simulation Ali Marzaban, CD-adapco Murthy Lakshmiraju, CD-adapco Nigel Richardson, CD-adapco Mike Henneke, CD-adapco Guangyu Wu, Chevron Pedro M. Vargas,
Pressure Vessel Engineering Ltd. ASME Calculations - CRN Assistance - Vessel Design - Finite Element Analysis
PVEng Pressure Vessel Engineering Ltd. ASME Calculations - CRN Assistance - Vessel Design - Finite Element Analysis Design Conditions Code: ASME VIII-1 Year: 2007 Finite Element Analysis Report - VIII-1
Tutorial. BOSfluids. Water hammer (part 3) Dynamic Analysis using Caesar II
BOSfluids Tutorial Water hammer (part 3) Dynamic Analysis using Caesar II The Water hammer tutorial is a 3 part tutorial describing the phenomena of water hammer in a piping system and how BOSfluids can
FEMAP Tutorial 2. Figure 1: Bar with defined dimensions
FEMAP Tutorial 2 Consider a cantilevered beam with a vertical force applied to the right end. We will utilize the same geometry as the previous tutorial that considered an axial loading. Thus, this tutorial
Integrity Evaluation of Small Bore Connections (Branch Connections)
Integrity Evaluation of Small Bore Connections (Branch Connections) by: Chris B. Harper, P.Eng. Principal Engineer Beta Machinery Analysis Calgary, Canada charper@betamachinery.com www.betamachinery.com
MAE Advanced Computer Aided Design. 01. Introduction Doc 02. Introduction to the FINITE ELEMENT METHOD
MAE 656 - Advanced Computer Aided Design 01. Introduction Doc 02 Introduction to the FINITE ELEMENT METHOD The FEM is A TOOL A simulation tool The FEM is A TOOL NOT ONLY STRUCTURAL! Narrowing the problem
ME 345: Modeling & Simulation. Introduction to Finite Element Method
ME 345: Modeling & Simulation Introduction to Finite Element Method Examples Aircraft 2D plate Crashworthiness 2 Human Heart Gears Structure Human Spine 3 F.T. Fisher, PhD Dissertation, 2002 Fluid Flow
Seven Techniques For Finding FEA Errors
Seven Techniques For Finding FEA Errors by Hanson Chang, Engineering Manager, MSC.Software Corporation Design engineers today routinely perform preliminary first-pass finite element analysis (FEA) on new
CALCULATION OF FLANGED JOINTS
Software and Services ASME, CEN, DIN, FEA, CALCULATION Stress Analysis, Fatigue Analysis, OF FLANGED JOINTS Tightness Analysis SOFTWARE AND S E R VI C E S Advanced Tools and Comprehensive Services for
LOCAL STRESS ANALYSIS OF STIFFENED SHELLS USING MSC/NASTRAN S SHELL AND BEAM p-elements
LOCAL STRESS ANALYSIS OF STIFFENED SHELLS USING MSC/NASTRAN S SHELL AND BEAM p-elements Sanjay Patel, Claus Hoff, Mark Gwillim The MacNeal-Schwendler Corporation Abstract In large finite element models
ANSYS AIM Tutorial Stepped Shaft in Axial Tension
ANSYS AIM Tutorial Stepped Shaft in Axial Tension Author(s): Sebastian Vecchi, ANSYS Created using ANSYS AIM 18.1 Contents: Problem Specification 3 Learning Goals 4 Pre-Analysis & Start Up 5 Calculation
Matching Real World Results
Matching Real World Results Randy Dreher FFE Minerals Inc. Jan Janssen, Doug Farnell, Stephen Thompson Farnell-Thompson Applied Technologies Inc Abstract Comparing measured results to those generated by
Finite Element Analysis Using Creo Simulate 4.0
Introduction to Finite Element Analysis Using Creo Simulate 4.0 Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
Simplified Design Procedure for Piles Affected by Lateral Spreading based on 3D Nonlinear FEA Using OpenSees. University of Washington
Simplified Design Procedure for Piles Affected by Lateral Spreading based on 3D Nonlinear FEA Using OpenSees Christopher R. McGann, Ph.D. Student Pedro Arduino Peter Mackenzie-Helnwein University of Washington
Types of Idealizations. Idealizations. Cylindrical Shaped Part. Cyclic Symmetry. 3D Shell Model. Axisymmetric
Types of Idealizations Idealizations Selecting the model type 3D Solid Plane Stress Plane Strain 3D Shell Beam Cyclic Symmetry Cylindrical Shaped Part Interior Pressure Load 3D model can be used to model
Input Echo, Nozzle Item 1, Description: Design Internal Pressure ( Case 1 ) P psig Temperature for Internal Pressure TEMP 250.
1 Input Echo, Nozzle Item 1, Description: Design Internal Pressure ( Case 1 ) P 125.00 psig Temperature for Internal Pressure TEMP 250.00 F Include Hydrostatic Head Components NO Shell or Head Material
FINITE ELEMENT MODELING AND EXPERIMENTAL VALIDATION OF BUCKLE ARRESTORS FOR DEEPWATER PIPELINES.
Mecánica Computacional Vol XXV, pp. 687-704 Alberto Cardona, Norberto Nigro, Victorio Sonzogni, Mario Storti. (Eds.) Santa Fe, Argentina, Noviembre 2006 FINITE ELEMENT MODELING AND EXPERIMENTAL VALIDATION
Table of Contents FE/Pipe v4.5 Release Documentation
Table of Contents FE/Pipe v4.5 Release Documentation 2007 Release: New Features... 2 2007 Release: Program Updates... 3 Section 1: 18 Degree of Freedom Beam Elements... 7 Section 2: API 579 Fitness for
DISTRIBUTED LOADS DISCRETIZATION IN COMPOSITE MATERIALS STRUCTURES TESTS
DISTRIBUTED LOADS DISCRETIZATION IN COMPOSITE MATERIALS STRUCTURES TESTS C. Arellano 1 1 Structural Laboratory, TEAMS, Wilbur y Orville Wright N1 AEROPOLIS 41309 La Rinconada, Espana Corresponding Author:
Modeling Strategies for Dynamic Finite Element Cask Analyses
Session A Package Analysis: Structural Analysis - Modeling Modeling Strategies for Dynamic Finite Element Cask Analyses Uwe Zencker, Günter Wieser, Linan Qiao, Christian Protz BAM Federal Institute for
CHAPTER-10 DYNAMIC SIMULATION USING LS-DYNA
DYNAMIC SIMULATION USING LS-DYNA CHAPTER-10 10.1 Introduction In the past few decades, the Finite Element Method (FEM) has been developed into a key indispensable technology in the modeling and simulation
Tutorial 1: Welded Frame - Problem Description
Tutorial 1: Welded Frame - Problem Description Introduction In this first tutorial, we will analyse a simple frame: firstly as a welded frame, and secondly as a pin jointed truss. In each case, we will
Finite Element Method using Pro/ENGINEER and ANSYS
Finite Element Method using Pro/ENGINEER and ANSYS Notes by R.W. Toogood The transfer of a model from Pro/ENGINEER to ANSYS will be demonstrated here for a simple solid model. Model idealizations such
Understanding 3D Structured Light To Assess Corrosion Defects
Understanding 3D Structured Light To Assess Corrosion Defects By Joe Pikas NACE Corrosion and Cathodic Protection Specialist Technical Toolboxes Consulting Ltd. ABSTRACT Phase Measurement Profilometry
Premium Drillpipe. for Optimal Performance
Premium Drillpipe for Optimal Performance DRILCO offers a full line of premium drillpipe available in a variety of sizes with API and non-standard wall thickness to deliver optimal torque, weight, and
FB-MULTIPIER vs ADINA VALIDATION MODELING
FB-MULTIPIER vs ADINA VALIDATION MODELING 1. INTRODUCTION 1.1 Purpose of FB-MultiPier Validation testing Performing validation of structural analysis software delineates the capabilities and limitations
Liebherr-Aerospace: Optical Metrology from GOM Accelerates Certification Tests for New Landing Gears
Application Note Liebherr-Aerospace: Optical Metrology from GOM Accelerates Certification Tests for New Landing Gears Location/Country: Lindenberg, Deutschland GOM system: ARAMIS GOM software: ARAMIS Professional
Preparation and Installation of the Composite Type Rupture Disc (Light Lip and Heavy Lip) in 30 Seat Insert, Full-Bolted, and Union Type Holder
GEP-7004 Rev. L 101251 Ref. ID: 5472 Preparation and Installation of the Composite Type Rupture Disc (Light Lip and Heavy Lip) in 30 Seat Insert, Full-Bolted, and Union Type Holder WARNING USER SHOULD
ANSYS Element. elearning. Peter Barrett October CAE Associates Inc. and ANSYS Inc. All rights reserved.
ANSYS Element Selection elearning Peter Barrett October 2012 2012 CAE Associates Inc. and ANSYS Inc. All rights reserved. ANSYS Element Selection What is the best element type(s) for my analysis? Best
Detail Analysis of Ship Structures
Detail Analysis of Ship Structures By David Heath, Neil Pegg Defence Research Establishment Atlantic, Dartmouth, Nova Scotia, Canada and Aaron Dinovitzer, Robert Walker Fleet Technology Limited, Kanata,
Generic Neutral Files
Chapter 8 Interfaces 8-57 Generic Neutral Files CAESAR II Neutral File Interface The general neutral file can be used to send data either in to or out of the standard CAESAR II binary input file, otherwise
Chapter 7 Practical Considerations in Modeling. Chapter 7 Practical Considerations in Modeling
CIVL 7/8117 1/43 Chapter 7 Learning Objectives To present concepts that should be considered when modeling for a situation by the finite element method, such as aspect ratio, symmetry, natural subdivisions,
Technical Issues. Frequently Asked Questions Frequently Encountered Errors. - Featuring - ADAPT-ABI 2009
Technical Issues Frequently Asked Questions Frequently Encountered Errors - Featuring - ADAPT-ABI 2009 ADAPT Corporation, USA ADAPT International Pvt. Ltd, Kolkata, India Tuesday, November 17, 2009 1 What
Creo Simulate 3.0 Tutorial
Creo Simulate 3.0 Tutorial Structure and Thermal Roger Toogood, Ph.D., P. Eng. SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
Quarter Symmetry Tank Stress (Draft 4 Oct 24 06)
Quarter Symmetry Tank Stress (Draft 4 Oct 24 06) Introduction You need to carry out the stress analysis of an outdoor water tank. Since it has quarter symmetry you start by building only one-fourth of
Case Study- Importing As-Molded Plastic Part Conditions into CAE tools
1 IEI Innova Engineering 1 Park Plaza Suite 980 Irvine, California 92614 Case Study- Importing As-Molded Plastic Part Conditions into CAE tools 2 CONTENTS CONTENTS... 2 EXECUTIVE SUMMARY... 3 APPROACH...