DL05 Error Codes. Appendix. In This Appendix... DL05 Error Codes...B 1

Transcription

1 L0 Error odes ppendix In This ppendix... L0 Error odes... 1

2 ppendix : L0 Error odes E00 SOFTWRE TIME-OUT L0 Error ode escription E00 INVLI INSTRUTION E0 M TTERY LOW E WRITE FILE E11 OMMN E2 ONFIGURE I/O RESS OUT OF RNGE E HP OMM ERROR 1 E HP OMM ERROR 2 E HP OMM ERROR E1 HP OMM E ERROR E20 HP OMM TIME-OUT E21 OMM ERROR If the program scan time exceeds the time allotted to the watchdog timer, this error will occur. SP1 will be on and the error code will be stored in V. To correct this problem use UX to extend the time allotted to the watchdog timer. The PU attempted to execute an instruction code, but the RM contents had a parity error. Performing a program download to the PU in an electrically noisy environment can corrupt a program s contents. lear the PU program memory, and download the program again. The battery in the MOS RM cartridge is low and should be replaced. write to the PU was not successful. isconnect the power, remove the PU, and make sure the EEPROM is not write protected. If the EEPROM is not write protected, make sure the EEPROM is installed correctly. If both conditions are OK, replace the PU. parity error has occurred in the application program. SP will be on and the error code will be stored in V. This problem may possibly be due to electrical noise. lear the memory and download the program again. orrect any grounding problems. If the error returns replace the Micro PL. Out of range addresses have been assigned while manually configuring the I/O. orrect the address assignments using UX. request from the handheld programmer could not be processed by the PU. lear the error and retry the request. If the error continues replace the PU. SP will be on and the error code will be stored in V. data error was encountered during communications with the PU. lear between the two devices, replace the handheld programmer, then if necessary replace the PU. The error code will be stored in V. n address error was encountered during communications with the PU. lear the error and retry the request. If the error continues, check the cabling between the two devices, replace the handheld programmer, then if necessary replace the PU. The error code will be stored in V. mode error was encountered during communications with the PU. lear the error and retry the request. If the error continues, replace the handheld programmer, then if necessary replace the PU. The error code will be stored in V. The PU did not respond to the handheld programmer communication request. heck to ensure cabling is correct and not defective. Power cycle the system. If the error continues, replace the PU first and then the handheld programmer, if necessary. data error was encountered during communication with the PU. heck to ensure cabling is correct and not defective. Power cycle the system. If the error continues, replace the PU first and then the handheld programmer, if necessary. -2 L0 Micro PL User Manual, th Edition, Rev. E

3 ppendix : L0 Error odes E0 HP PERIPHERL PORT TIME-OUT E** NO PROGRM L0 Error ode E01 MISSING EN STTEMENT E02 MISSING LL E0 MISSING RET E0 MISSING FOR E0 MISSING NEXT E0 MISSING IRT E SR/LL> E21 UPLITE STGE REFERENE E22 UPLITE LL REFERENE E2 NESTE LOOPS E1 INVLI ISG/SG RESS escription The device connected to the peripheral port did not respond to the handheld programmer communication request. heck to ensure cabling is correct and not defective. The peripheral device or handheld programmer could be defective. syntax error exists in the application program. The most common is a missing EN statement. Run UX21 to determine which one of the E** series of errors is being flagged. ll application programs must terminate with an EN statement. Enter the EN statement in appropriate location in your program. MOVM or LLL instruction was used without the appropriate label. Refer to hapter for details on these instructions. subroutine in the program does not end with the RET instruction. NEXT instruction does not have the corresponding FOR instruction. FOR instruction does not have the corresponding NEXT instruction. n interrupt routine in the program does not end with the IRT instruction. There is greater than SR or LL instructions in the program. This error is also returned if there are greater than 2 INT instructions used in the program. Two or more SG or ISG labels exist in the application program with the same number. unique number must be allowed for each Stage and Initial Stage. Two or more LL instructions exist in the application program with the same number. unique number must be allowed for each and label. Nested loops (programming one FOR/NEXT loop inside of another) are not allowed. n ISG or SG instruction must not be placed after the end statement (such as inside a subroutine). L0 Micro PL User Manual, th Edition, Rev. E -

4 ppendix : L0 Error odes E INVLI SR RESS E INVLI RT RESS E INVLI RT RESS E INVLI INT RESS E INVLI IRT RESS E INVLI IRT RESS E0 INVLI T RESS E1 ON/NON E1 MLS/MLR E MISSING T/ E TMR E NT E SR L0 Error ode escription n SR must be programmed after the end statement, not in the main body of the program or in an interrupt routine. n RT must be programmed after the end statement, not in the main body of the program or in an interrupt routine. n RT must be programmed after the end statement, not in the main body of the program or in an interrupt routine. n INT must be programmed after the end statement, not in the main body of the program. n IRT must be programmed after the end statement, not in the main body of the program. n IRT must be programmed after the end statement, not in the main body of the program. Either the LL instruction has been programmed in the main program area (not after the EN statement), or the LL instruction is on a rung containing input contact(s). n ON or NON must be programmed after the end statement, not in the main body of the program. MLS instructions must be numbered in ascending order from top to bottom. timer or counter contact is being used where the associated timer or counter does not exist. One of the contacts is missing from a TMR instruction. One of the contacts is missing from a NT or U instruction. One of the contacts is missing from the SR instruction. - L0 Micro PL User Manual, th Edition, Rev. E

5 ppendix : L0 Error odes E1 STK OVERFLOW E2 STK UNERFLOW E LOGI ERROR E MISSING KT E1 UPLITE OIL REFERENE E2 UPLITE TMR REFERENE E UPLITE NT REFERENE E PRINT INSTRUTION L0 Error ode escription More than nine levels of logic have been stored on the stack. heck the use of OR STR and N STR instructions. n unmatched number of logic levels have been stored on the stack. Ensure the number of N STR and OR STR instructions match the number of STR instructions. STR instruction was not used to begin a rung of ladder logic. rung of ladder logic is not terminated properly. Two or more OUT instructions reference the same I/O point. Two or more TMR instructions reference the same number. Two or more NT instructions reference the same number. Invalid PRINT instruct usage. Quotations and/or spaces were not entered or entered incorrectly. L0 Micro PL User Manual, th Edition, Rev. E -

6 ppendix : L0 Error odes L0 Error ode E01 ENTRY E02 RESS E0 OMMN E0 REF/VL E0 INVLI INSTRUTION E0 INVLI OPERTION E20 OP RUN E21 OP TRUN E2 OP TPGM E2 OP PGM E2 MOE SWITH E2 OFF LINE E2 ON LINE E2 PU MOE E0 PU LOKE E1 WRONG PSSWOR E2 PSSWOR RESET E01 MEMORY FULL E02 INSTRUTION MISSING escription n invalid keystroke or series of keystrokes was entered into the handheld programmer. n invalid or out of range address was entered into the handheld programmer. n invalid command was entered into the handheld programmer. n invalid value or reference number was entered with an instruction. n invalid instruction was entered into the handheld programmer or a program which includes an instruction requiring a Memory artridge (0-01M) to be installed in the L0, but was placed in RUN without the M. n invalid operation was attempted by the handheld programmer. n operation which is invalid in the RUN mode was attempted by the handheld programmer. n operation which is invalid in the TEST RUN mode was attempted by the handheld programmer. n operation which is invalid in the TEST PROGRM mode was attempted by the handheld programmer. n operation which is invalid in the PROGRM mode was attempted by the handheld programmer. n operation was attempted by the handheld programmer while the PU mode switch was in a position other than the TERM position. The handheld programmer is in the OFFLINE mode. To change to the ONLINE mode use the MOE key. The handheld programmer is in the ON LINE mode. To change to the OFF LINE mode use the MOE key. The operation attempted is not allowed during a Run Time Edit. The PU has been password locked. To unlock the PU use UX2 with the password. The password used to unlock the PU with UX2 was incorrect. The PU powered up with an invalid password and reset the password to password may be re-entered using UX1. ttempted to enter an instruction which required more memory than is available in the PU. search function was performed and the instruction was not found. - L0 Micro PL User Manual, th Edition, Rev. E

7 ppendix : L0 Error odes L0 Error ode E0 T MISSING E0 REFERENE MISSING E20 OUT OF MEMORY E21 EEPROM NOT LNK E22 NO HPP EEPROM E2 SYSTEM EEPROM E2 V-MEMORY ONLY E2 PROGRM ONLY E2 PROM M E2 WRITE E2 EEPROM TYPE ERROR E0 OMPRE ERROR E1 VOLUME LEVEL E2 HEKSUM ERROR E0 HPP SYSTEM ERROR E1 HPP ROM ERROR E2 HPP RM ERROR escription search function was performed and the data was not found. search function was performed and the reference was not found. n attempt to transfer more data between the PU and handheld programmer than the receiving device can hold. n attempt to write to a non-blank EEPROM in the handheld programmer was made. Erase the EEPROM and then retry the write. data transfer was attempted with no EEPROM (or possibly a faulty EEPROM) installed in the handheld programmer. function was requested with an EEPROM in the handheld programmer which contains system information only. function was requested with an EEPROM in the handheld programmer which contains V-memory data only. function was requested with an EEPROM in the handheld programmer which contains program data only. n attempt to transfer data from a tape to a UVPROM Memory artridge. This transfer must be made using a MOS RM artridge. n attempt to write to a write-protected or faulty EEPROM in the handheld programmer was made. heck the write protect jumper and replace the EEPROM if necessary. The wrong size EEPROM is being used in the handheld programmer. This error occurs when the program size is larger than what the HPP can hold. compare between the EEPROM handheld programmer and the PU was found to be in error. The volume level of the cassette player is not set properly. djust the volume and retry the operation. n error was detected while data was being transferred to the handheld programmer s Memory artridge. heck cabling and retry the operation. system error has occurred in the handheld programmer. Power cycle the handheld programmer. If the error returns replace the handheld programmer. ROM error has occurred in the handheld programmer. Power cycle the handheld programmer. If the error returns replace the handheld programmer. RM error has occurred in the handheld programmer. Power cycle the handheld programmer. If the error returns replace the handheld programmer. L0 Micro PL User Manual, th Edition, Rev. E -