HPE 3PAR StoreServ 8000 Series Cabling Instructions 4 Node 12 Drive Enclosures (12S) 4 medium (2m) SAS cables 22 short (1m) SAS cables

Transcription

1 01 HPE 3PAR StoreServ 8000 Series Cabling Instructions 4 Node 12 Drive Enclosures (12S) 4 medium (2m) SAS cables 22 short (1m) SAS cables All steps in this document, including application of the HPE 3PAR StoreServ 8000 Family Cable Label Kit, must be used to properly cable this system! Nodes 2/ Nodes 0/

2 Key: Labels and Enclosure Ports Legend for cable label content 8400/8440/8450 (4 node system) M6810 (SFF Drive Enclosure)

3 Step 1: Label Drive Enclosures Connected to Nodes 0 and 1 A. Find the Enclosure Labels for Nodes 0 and 1 that match those seen on the diagram below. B. Apply labels as seen in the diagram to the left rail of each disk enclosure. DO NOT LABEL THE CONTROLLER NODE ENCLOSURES Nodes 0/

4 Step 2: Label the Node 0 Cables Node 0 Number of cables Length Labels 6m 2m 7 1m A F A. Find the labels for Node 0 in the Label Kit. B. Select six short, 1m cables. Apply labels in row A to each end of one cable. Apply labels in rows B-F to each end of the remaining cables.

5 Step 3: Cable Node 0 with Red Label Cables A. Install the six short, 1m cables for Node 1 into the ports identified on the cable label. B. Use the diagram below to verify that all cabling is correct after connecting all the cables. Nodes 0/1

6 Step 4: Label the Node 1 Cables Node 1 Number of cables Length Labels 6m 2 2m E, F 5 1m J M A. Find the labels for Node 1 in the Label Kit. B. Select two medium, 2m cables. Apply labels in row E to each end of one cable. Apply labels in row F to each end of the remaining cable. C. Select four short, 1m cables. Apply labels in row J to each end of one cable. Apply labels in rows K-M to each end of the remaining cables.

7 Step 5: Cable Node 1 with Green Label Cables A. Install the two medium, 2m cables for Node 1 into the ports identified on the cable label. B. Install the four short, 1m cables for Node 1 into the ports identified on the cable label. C. Use the diagram below to verify that all cabling is correct after connecting all the cables. Nodes 0/1

8 Step 6: Label Drive Enclosures Connected to Nodes 2 and 3 A. Find the Enclosure Labels for Nodes 2 and 3 that match those seen on the diagram below. B. Apply labels as seen in the diagram to the left rail of each disk enclosure. DO NOT LABEL THE CONTROLLER NODE ENCLOSURES Nodes 2/

9 Step 7: Label the Node 2 Cables Node 2 Number of cables Length Labels 6m 2m 6 1m A F A. Find the labels for Node 2 in the Label Kit. B. Select six short, 1m cables. Apply labels in row A to each end of one cable. Apply labels in rows B-F to each end of the remaining cables.

10 Step 8: Cable Node 2 with Red Label Cables A. Install the six short, 1m cables for Node 1 into the ports identified on the cable label. B. Use the diagram below to verify that all cabling is correct after connecting all the cables. Nodes 2/3

11 Step 9: Label the Node 3 Cables Node 3 Number of cables Length Labels 6m 2 2m E, F 4 1m J M A. Find the labels for Node 3 in the Label Kit. B. Select two medium, 2m cables. Apply labels in rows E and F to each end of the cables. C. Select four short, 1m cables. Apply labels in row J to each end of one cable. Apply labels in rows K-M to each end of the remaining cables.

12 Step 10: Cable Node 3 with Green Label Cables A. Install the two medium, 2m cables for Node 1 into the ports identified on the cable label. B. Install the five short, 1m cables for Node 1 into the ports identified on the cable label. C. Use the diagram below to verify that all cabling is correct after connecting all the cables. Nodes 2/3

13 Step 11: Node Interconnect Cabling A. Find the four Node Interconnect cables The cables are DIRECTIONAL and must be installed correctly for the system to function properly. B. Connect one cable at a time as follows: 1. Controller A, Node 0, Intr 0 Controller C, Node 2, Intr 1 2. Controller A, Node 0, Intr 1 Controller C, Node 3, Intr 0 3. Controller A, Node 1, Intr 0 Controller C, Node 3, Intr 1 4. Controller A, Node 1, Intr 1 Controller C, Node 2, Intr 0 C. After confirming that all cabling is correct (SAS and interconnection) the system may be powered on using the procedure in the Installation Guide. Intr 1 Intr 0 C Node 3 Node Intr 0 Intr 1 C C C C 1 0 Node 1 A A A 3 Intr 1 Intr 0 3 Node 0 2 A A 2 Intr 0 Intr 1