Puji Innovations: Smart Switch 6+2 (BLE Mesh)

Transcription

1 Puji Innovations: Smart Switch 6+2 (BLE Mesh) User manual Transform home into a state-of-the-art smart home using the plug-in BLE Mesh enabled Smart Switch. This one-of-a-kind smart switch allows to wirelessly control electrical devices, lamp dimmer and fan/curtain/motor regulator, small appliance or electronic device in home. It features establish BLE mesh network, touch sensor interface to control operation from Switch panel. The BLE mesh enabled Smart Switch provides coverage for entire home through the use of the mobile app and does not require any wiring for stressfree use. Features: Crystal glass touch screen Keypads. Control appliances with a gentle touch equipped with a stunning OLED display & LED backlit. Wirelessly control electrical devices/lights from your smartphone or tablet. Dimmer Works with incandescent bulbs, Fan, curtain, Gate or electrical motors. Android app is ready to connect to BLE mesh enabled devices/switches. Supported Android 4.3 or later. Smart control repeats the signal up to 100 feet. Bluetooth Smart wireless mesh network provides coverage for entire home by simply adding more Smart routers. At any point in time, Smart Switch can exhibit one of the roles: Source Relay Destination Switch is uniquely identified with 128-bit Device UUID Mobile control Messages can be sent to an individual node or to a group Just 10 mins installation. Relay switch supports below listed electrical power supply, 7A 250V AC 12A 120V DC 10A 120VAC 10A 24VDC How it works? Creates a BLE mesh network from existing Bluetooth Smart & Smart Ready devices Smart Switches in BLE mesh network, repeats the signal to next node. o Extends range of Bluetooth Smart by repeating messages Switches are organized into secure networks Smart Switch BLE mesh Networks are secured using a network key All Switches within network are trusted devices All messages within the same network are encrypted with the network key Smart Switch is a single node in the network (Note: Above eample is only for representation, check electric device power requirements before connecting) Smart-Switch supports upto 7A 250V AC maximum, check electicric device power requirement before connecting (connecting High load device can damage the board). How to Install Smart Switch device? Switch-off your mains/mcb power supply of the room. Follow instruction in the Installation Guide. Connect the Smart Switch to your Switch board.

2 Download Smart Home Switch App from Google Play. Configure your Smart switch in your android Phone and start experience the Smart Home excitement. Smart Home Switch App: Smart Home switch app is freely downloadable from Google Play (search SmartSwitchBSmartMesh ) Note: Bug-free and latest app available only via Google Play After successful installation, you need to configure installed app to work with smart switch device, Below are the steps to configure Smart Switch App. Launch the Android application. The initial screen shown in Figure below shows a Scan and Connect button. Press Scan and Connect to discover devices that support the Smart Switch mesh service and connect to the nearest device. The application will automatically connect to the closest device based on the RSSI value. Setting up a Network To setup a Smart Switch mesh network a network key needs to be generated from a passphrase. This section describes the steps for generating a network key to start setting up a new network: Once the application connects to a Smart-Switch mesh device, a drop down menu is enabled which can be used to navigate to any of the Smart-Switch mesh control pages. Select the Security Settings page as shown in Figure below. The first time the application is started it will go to this page automatically. Enter a passphrase and press OK to setup a new network key. This network key will be used to associate new devices to the The security settings screen also shows the Bluetooth address of the connected bridge device. Note: It is important to un-check Authorise Devices if the Smart- Switch mesh devices do not support the authorisation code

3 feature as otherwise it will not be possible to associate devices. Once the device is associated a message box is displayed showing the 16-bit Device ID assigned to the device. Associating Devices to a Network In order to join devices to the Smart-Switch mesh network, the following steps need to be followed: Navigate to the Device Association screen from the main menu, see Figure below. The display will list the 128-bit UUIDs of the devices available for association, the device type will be displayed with the signal strength and the number of hops of the signal received. Select the UUID of a device to associate it to the Configuration Menu Select the Configuration page from the application main menu. The Configuration screen lists the groups and associated switches as shown in Figure below. By default the application provides four groups to which no switch will have been assigned. Touch and hold a Switch to pop-up a menu to configure the selected switch. A message will display to indicate association is in progress. Select Rename to rename a switch. Select Delete to remove the switch from the Select Device Info to see further information on the chosen switch including the supported models. Select Firmware Info to get the firmware information for a switch.

4 Select Request Data for a demonstration of Data Model. This sends a request to the device using data model and then displays the data received. Touch and hold a group item in order to pop-up a menu configure the selected group. Select Rename to rename the group. Select Delete to remove the group from the Select Request Data for a demonstration of Data Model. This sends a request to the whole list of devices which belong to the group using data model and then displays a list of device ids which have sent a message back to the request. Group Setup Switches can be placed into different groups. Select a group to show the check boxes against the switches. Check the items to be assigned to the group and click Apply. Select a switch to show check boxes against the groups. Check the groups to which the item should be assigned and click Apply.

5 Adding Switch to multiple group Controlling Switches The Switch Control page of the application lists all associated switches and configured groups. Select an individual switch, all switches or a group from the drop down list as shown in Figure below. Tap the power button to turn the connected lights/electrical device on or off. Move the slider at the bottom to adjust the brightness/speed of the selected lights/fan. Further questions or clarification please do contact support@pujiinnovations.com (+91)