Model IR400 Infrared Gas Analyzer (22) Sample gas inlet Rc1/4 or 1/4 NPT

Transcription

1 Drawings Model IR00 Infrared Gas Analyzer [Style: S] <Top View> <Side View> Slide rail (). Power Switch <Front View> Sample gas inlet Rc1/ or 1/ NPT. <Rack mounting hole> M JIS : 100 mm EIA : 101. mm. Sample gas outlet Rc1/ or 1/ NPT Purge gas inlet Rc1/ or 1/ NPT <Rear View> 1. Fuse Power Inlet Connector for input/output terminal module Weight: Approx. kg Unless otherwise specified, differences in the dimensions are specified as: General tolerance = ±(Criteria of tolerance class IT1 in JIS B001-1)/. All Rights Reserved, Copyright 00, Yokogawa Electric Corporation. Subject to change without notice. SD 11G0N01-01E 1/ 1st Edition: Aug. 00 (YK) th Edition: Feb. 01 (YK)

2 Accessory Input/Output Module Mounting hole -. hole Screw terminals M. <TN1> <TN> <TN> <TN> <TN> Connector <CN>. Input/Output terminal module connector <CN1> M screw (0) Connector <CN> Dimensions for Mounting Input/Output Module Cut M screw holes at positions. Drill a rectangular hole of 0 x 1 mm or more in the center. F0.ai Cable for connecting Input/Output 1000±0 Unit : mm Unless otherwise specified, differences in the dimensions are specified as: General tolerance = ±(Criteria of tolerance class IT1 in JIS B001-1)/. SD 11G0N01-01E / th Edition:Feb. 01 (YK)

3 Slide Rail Model: equivalent to 0A-/Accuride International Inc. Closed Cabinet member 1.t Intermediate member Drawer member 1.t (.). ±0. 1. ±0. 1. ±0. 1. ±0. 1. ±0. ± (.). ± ±0. 0.±0. Reinforcement plate (.).. 1. ±0.. ±0. The slide rail is supplied at the delivery time. Closed position flush or under Open 10 ±0.. ±0..1 ±0. ± ±0. 1. ±0. <1-inch rack mounting method> For easy maintenance, we recommended the mounting method which allows the rack to be drawn out along the slide rail... Rack size With slide rails With guide rails * Rack size 0 or more 101. or or more 101. or 100 Mounting diagram Mounting diagram Slide rails Guide rails * For mounting with guide rails, a maintenance space (00 mm or more) should be provided on top of the main unit. Unless otherwise specified, differences in the dimensions are specified as: General tolerance = ±(Criteria of tolerance class IT1 in JIS B001-1)/. SD 11G0N01-01E / th Edition:Feb. 01 (YK)

4 Dedicated Relay Board (option code /R) Less than 1 Mounting Hole. CN1 CN CN1 CN CN CN CN CN CN CN F10-E.ai <How to connect> CN CN1 CN CN CN CN CN CN CN Reserved Solenoid valve driving power For switching sample For zero gas CH1 CH CH CH CH For span gas Solenoid valve CN1 CN Relay board I/O terminal module Dedicated cable (D-sub -pin straight cable 1. m) F11.ai Unless otherwise specified, differences in the dimensions are specified as: General tolerance = ±(Criteria of tolerance class IT1 in JIS B001-1)/. SD 11G0N01-01E / th Edition:Feb. 01 (YK)

5 External Connection Diagram 1 <TN1> Ch output - (Ch_OUT) + Ch output 1 (Ch_OUT) 1 Ch output 1 (Ch_OUT) 1 Ch output 1 (Ch_OUT) 1 Ch1 output 1 (Ch1_OUT) (M. screw) Ch10 output (Ch10_OUT) Ch output (Ch_OUT) Ch output (Ch_OUT) Ch output (Ch_OUT) Ch output (Ch_OUT) <TN> Ch1 output (Ch1_OUT) Ch11 output (Ch11_OUT) (M. screw) O analyzer input* (O _IN) Ch remote range (R_RNG_Ch) Ch remote range (R_RNG_Ch) Ch remote range (R_RNG_Ch) Ch remote range (R_RNG_Ch) Ch1 remote range (R_RNG_Ch1) * For external O analyzer input. <TN> Ch range identification signal output (RNG_ID_Ch) Peak count alarm output (PEAK_ALM) <TN> 1 1 Ch range identification signal output (RNG_ID_Ch) Auto calibration status contact output (ACAL/MNT) 1 1 Remote hold input (R_HOLD) 1 1 Ch range identification signal output (RNG_ID_Ch) Pump ON/OFF contact output (PUMP) 1 1 Average value reset input (RESET) Auto calibration remote start input (R_CAL) (M. screw) Ch range identification signal output (RNG_ID_Ch) Ch1 range identification signal output (RNG_ID_Ch1) Calibration error contact output (CAL_ALM) Instrument error contact output (FAULT) (M. screw) <TN> Connector <CN> Solenoid valve drive signal output for calibration Alarm output (ALM) Alarm output (ALM) Alarm1 output (ALM1) Alarm output (ALM) Alarm output (ALM) Alarm output (ALM) Contact output for sample gas selecting 1 Contact output for zero calibration Contact output for Ch1 Contact output for Ch <D-sub P> Contact output for Ch Contact output for Ch Contact output for Ch Power for relay drive V DC (M. screw) Note 1: terminals are used for internal connection. So they should not be used as repeating terminals either. Note : The allocation of each channel (Ch1 to Ch1) depends on measured gas components. Refer to the table on the next page. F0.ai SD 11G0N01-01E / th Edition:Feb. 01 (YK)